<
From version < 112.1 >
edited by Xiaoling
on 2022/06/10 15:00
To version < 111.31 >
edited by Xiaoling
on 2022/06/10 14:53
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -875,81 +875,56 @@
875 875  * The sensor window is made by Acrylic. Don’t touch it with alcohol material. This will destroy the sensor window.
876 876  
877 877  
878 +
878 878  = 4.  Configure LLDS12 via AT Command or LoRaWAN Downlink =
879 879  
880 880  (((
881 -(((
882 882  Use can configure LLDS12 via AT Command or LoRaWAN Downlink.
883 883  )))
884 -)))
885 885  
886 886  * (((
887 -(((
888 888  AT Command Connection: See [[FAQ>>||anchor="H7.A0FAQ"]].
889 889  )))
890 -)))
891 891  * (((
892 -(((
893 893  LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>doc:Main.WebHome]]
894 894  )))
895 -)))
896 896  
897 897  (((
898 -(((
899 899  
900 -)))
901 901  
902 -(((
903 903  There are two kinds of commands to configure LLDS12, they are:
904 904  )))
905 -)))
906 906  
907 907  * (((
908 -(((
909 909  (% style="color:#4f81bd" %)** General Commands**.
910 910  )))
911 -)))
912 912  
913 913  (((
914 -(((
915 915  These commands are to configure:
916 916  )))
917 -)))
918 918  
919 919  * (((
920 -(((
921 921  General system settings like: uplink interval.
922 922  )))
923 -)))
924 924  * (((
925 -(((
926 926  LoRaWAN protocol & radio related command.
927 927  )))
928 -)))
929 929  
930 930  (((
931 -(((
932 932  They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
933 933  )))
934 -)))
935 935  
936 936  (((
937 -(((
938 938  
939 939  )))
940 -)))
941 941  
942 942  * (((
943 -(((
944 944  (% style="color:#4f81bd" %)** Commands special design for LLDS12**
945 945  )))
946 -)))
947 947  
948 948  (((
949 -(((
950 950  These commands only valid for LLDS12, as below:
951 951  )))
952 -)))
953 953  
954 954  
955 955  
... ... @@ -985,8 +985,6 @@
985 985  
986 986  )))
987 987  
988 -
989 -
990 990  == 4.2  Set Interrupt Mode ==
991 991  
992 992  Feature, Set Interrupt mode for GPIO_EXIT.
... ... @@ -1015,8 +1015,6 @@
1015 1015  Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
1016 1016  )))
1017 1017  
1018 -
1019 -
1020 1020  == 4.3  Get Firmware Version Info ==
1021 1021  
1022 1022  Feature: use downlink to get firmware version.
... ... @@ -1213,14 +1213,10 @@
1213 1213  
1214 1214  
1215 1215  (((
1216 -(((
1217 1217  In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LLDS12.
1218 -)))
1219 1219  
1220 -(((
1221 1221  LLDS12 will output system info once power on as below:
1222 1222  )))
1223 -)))
1224 1224  
1225 1225  
1226 1226   [[image:1654593712276-618.png]]
... ... @@ -1241,9 +1241,7 @@
1241 1241  == 8.1  AT Commands input doesn’t work ==
1242 1242  
1243 1243  
1244 -(((
1245 1245  In the case if user can see the console output but can’t type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn’t send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
1246 -)))
1247 1247  
1248 1248  
1249 1249  == 8.2  Significant error between the output distant value of LiDAR and actual distance ==
Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0