Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -63,6 +63,9 @@
63	63	* Downlink to change configure
64	64	* 8500mAh Battery for long term use
65	65
	66	+
	67	+
	68	+
66	66	== 1.3  Probe Specification ==
67	67
68	68	* Storage temperature ：-20℃~~75℃
...	...	@@ -78,6 +78,9 @@
78	78	* Material of enclosure - ABS+PC
79	79	* Wire length - 25cm
80	80
	84	+
	85	+
	86	+
81	81	== 1.4  Probe Dimension ==
82	82
83	83
...	...	@@ -94,6 +94,9 @@
94	94	* Automatic control
95	95	* Sewer
96	96
	103	+
	104	+
	105	+
97	97	== 1.6  Pin mapping and power on ==
98	98
99	99
...	...	@@ -874,8 +874,6 @@
874	874	* The LiDAR probe is cover by dirty things; the reading might be wrong. In this case, need to clean the probe.
875	875	* The sensor window is made by Acrylic. Don’t touch it with alcohol material. This will destroy the sensor window.
876	876
877		-
878		-
879	879	= 4.  Configure LLDS12 via AT Command or LoRaWAN Downlink =
880	880
881	881	(((
...	...	@@ -963,7 +963,6 @@
963	963	[[image:image-20220607171554-8.png]]
964	964
965	965
966		-
967	967	(((
968	968	(% style="color:#037691" %)**Downlink Command: 0x01**
969	969	)))
...	...	@@ -986,6 +986,7 @@
986	986
987	987	)))
988	988
	995	+
989	989	== 4.2  Set Interrupt Mode ==
990	990
991	991	Feature, Set Interrupt mode for GPIO_EXIT.
...	...	@@ -1014,6 +1014,7 @@
1014	1014	Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
1015	1015	)))
1016	1016
	1024	+
1017	1017	== 4.3  Get Firmware Version Info ==
1018	1018
1019	1019	Feature: use downlink to get firmware version.
...	...	@@ -1210,10 +1210,14 @@
1210	1210
1211	1211
1212	1212	(((
	1221	+(((
1213	1213	In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LLDS12.
	1223	+)))
1214	1214
	1225	+(((
1215	1215	LLDS12 will output system info once power on as below:
1216	1216	)))
	1228	+)))
1217	1217
1218	1218
1219	1219	[[image:1654593712276-618.png]]
...	...	@@ -1234,7 +1234,9 @@
1234	1234	== 8.1  AT Commands input doesn’t work ==
1235	1235
1236	1236
	1249	+(((
1237	1237	In the case if user can see the console output but can’t type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn’t send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
	1251	+)))
1238	1238
1239	1239
1240	1240	== 8.2  Significant error between the output distant value of LiDAR and actual distance ==