Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -875,56 +875,81 @@
875	875	* The sensor window is made by Acrylic. Don’t touch it with alcohol material. This will destroy the sensor window.
876	876
877	877
878		-
879	879	= 4.  Configure LLDS12 via AT Command or LoRaWAN Downlink =
880	880
881	881	(((
	881	+(((
882	882	Use can configure LLDS12 via AT Command or LoRaWAN Downlink.
883	883	)))
	884	+)))
884	884
885	885	* (((
	887	+(((
886	886	AT Command Connection: See [[FAQ>>||anchor="H7.A0FAQ"]].
887	887	)))
	890	+)))
888	888	* (((
	892	+(((
889	889	LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>doc:Main.WebHome]]
890	890	)))
	895	+)))
891	891
892	892	(((
	898	+(((
893	893
	900	+)))
894	894
	902	+(((
895	895	There are two kinds of commands to configure LLDS12, they are:
896	896	)))
	905	+)))
897	897
898	898	* (((
	908	+(((
899	899	(% style="color:#4f81bd" %)** General Commands**.
900	900	)))
	911	+)))
901	901
902	902	(((
	914	+(((
903	903	These commands are to configure:
904	904	)))
	917	+)))
905	905
906	906	* (((
	920	+(((
907	907	General system settings like: uplink interval.
908	908	)))
	923	+)))
909	909	* (((
	925	+(((
910	910	LoRaWAN protocol & radio related command.
911	911	)))
	928	+)))
912	912
913	913	(((
	931	+(((
914	914	They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
915	915	)))
	934	+)))
916	916
917	917	(((
	937	+(((
918	918
919	919	)))
	940	+)))
920	920
921	921	* (((
	943	+(((
922	922	(% style="color:#4f81bd" %)** Commands special design for LLDS12**
923	923	)))
	946	+)))
924	924
925	925	(((
	949	+(((
926	926	These commands only valid for LLDS12, as below:
927	927	)))
	952	+)))
928	928
929	929
930	930
...	...	@@ -960,6 +960,8 @@
960	960
961	961	)))
962	962
	988	+
	989	+
963	963	== 4.2  Set Interrupt Mode ==
964	964
965	965	Feature, Set Interrupt mode for GPIO_EXIT.
...	...	@@ -988,6 +988,8 @@
988	988	Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
989	989	)))
990	990
	1018	+
	1019	+
991	991	== 4.3  Get Firmware Version Info ==
992	992
993	993	Feature: use downlink to get firmware version.
...	...	@@ -1184,10 +1184,14 @@
1184	1184
1185	1185
1186	1186	(((
	1216	+(((
1187	1187	In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LLDS12.
	1218	+)))
1188	1188
	1220	+(((
1189	1189	LLDS12 will output system info once power on as below:
1190	1190	)))
	1223	+)))
1191	1191
1192	1192
1193	1193	[[image:1654593712276-618.png]]
...	...	@@ -1208,7 +1208,9 @@
1208	1208	== 8.1  AT Commands input doesn’t work ==
1209	1209
1210	1210
	1244	+(((
1211	1211	In the case if user can see the console output but can’t type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn’t send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
	1246	+)))
1212	1212
1213	1213
1214	1214	== 8.2  Significant error between the output distant value of LiDAR and actual distance ==