Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -300,6 +300,7 @@
300	300	|(% style="width:160px" %)0x01|(% style="width:163px" %)Normal Uplink|(% style="width:173px" %)[[Normal Uplink Payload>>||anchor="H2.3A0200BUplinkPayload"]]
301	301	|(% style="width:160px" %)0x02|(% style="width:163px" %)Reply configures info|(% style="width:173px" %)[[Configure Info Payload>>||anchor="H4.3A0GetFirmwareVersionInfo"]]
302	302
	303	+
303	303	=== 2.3.8  Decode payload in The Things Network ===
304	304
305	305	While using TTN network, you can add the payload format to decode the payload.
...	...	@@ -468,6 +468,8 @@
468	468	* Check what sub-band the LoRaWAN server ask from the OTAA Join Accept message and switch to that sub-band
469	469	* Use the Join successful sub-band if the server doesn’t include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include)
470	470
	472	+
	473	+
471	471	=== 2.6.3  CN470-510 (CN470) ===
472	472
473	473	(((
...	...	@@ -578,6 +578,8 @@
578	578	* Check what sub-band the LoRaWAN server ask from the OTAA Join Accept message and switch to that sub-band
579	579	* Use the Join successful sub-band if the server doesn’t include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include)
580	580
	584	+
	585	+
581	581	=== 2.6.5  AS920-923 & AS923-925 (AS923) ===
582	582
583	583	(((
...	...	@@ -804,6 +804,7 @@
804	804	* The sensor is detected when the device is turned on, and it will flash 4 times quickly when it is detected.
805	805	* Blink once when device transmit a packet.
806	806
	812	+
807	807	== 2.8  ​Firmware Change Log ==
808	808
809	809
...	...	@@ -831,11 +831,11 @@
831	831	[[image:1654831774373-275.png]]
832	832
833	833
834		-(% style="color:blue" %)**① **(%%)Represents the detection blind zone of The LiDAR probe, 0-10cm, within which the output data is unreliable.
	840	+①Represents the detection blind zone of The LiDAR probe, 0-10cm, within which the output data is unreliable.
835	835
836		-(% style="color:blue" %)**② **(%%)Represents the operating range of The LiDAR probe detecting black target with 10% reflectivity, 0.1-5m.
	842	+②Represents the operating range of The LiDAR probe detecting black target with 10% reflectivity, 0.1-5m.
837	837
838		-(% style="color:blue" %)**③ **(%%)Represents the operating range of The LiDAR probe detecting white target with 90% reflectivity, 0.1-12m.
	844	+③Represents the operating range of The LiDAR probe detecting white target with 90% reflectivity, 0.1-12m.
839	839
840	840
841	841	Vertical Coordinates: Represents the radius of light spot for The LiDAR probe at the different distances. The diameter of light spot depends on the FOV of The LiDAR probe (the term of FOV generally refers to the smaller value between the receiving angle and the transmitting angle), which is calculated as follows:
...	...	@@ -976,6 +976,9 @@
976	976	Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
977	977	)))
978	978
	985	+
	986	+
	987	+
979	979	== 4.3  Get Firmware Version Info ==
980	980
981	981	Feature: use downlink to get firmware version.
...	...	@@ -1004,7 +1004,7 @@
1004	1004
1005	1005	Version
1006	1006	)))|Sensor Type|Reserve|(((
1007		-[[Message Type>>||anchor="H2.3.7A0MessageType"]]
	1016	+[[Message Type>>||anchor="H2.3.6MessageType"]]
1008	1008	Always 0x02
1009	1009	)))
1010	1010
...	...	@@ -1172,15 +1172,13 @@
1172	1172
1173	1173
1174	1174	(((
1175		-In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LLDS12.
1176		-
1177		-LLDS12 will output system info once power on as below:
	1184	+In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LSPH01. LSPH01 will output system info once power on as below:
1178	1178	)))
1179	1179
1180	1180
1181	1181	[[image:1654593712276-618.png]]
1182	1182
1183		-Valid AT Command please check [[Configure Device>>||anchor="H4.A0ConfigureLLDS12viaATCommandorLoRaWANDownlink"]].
	1190	+Valid AT Command please check [[Configure Device>>||anchor="H3.ConfigureLSPH01viaATCommandorLoRaWANDownlink"]].
1184	1184
1185	1185
1186	1186	= 7.  FAQ =
...	...	@@ -1187,7 +1187,7 @@
1187	1187
1188	1188	== 7.1  How to change the LoRa Frequency Bands/Region ==
1189	1189
1190		-You can follow the instructions for [[how to upgrade image>>||anchor="H2.8A0200BFirmwareChangeLog"]].
	1197	+You can follow the instructions for [[how to upgrade image>>||anchor="H2.10200BFirmwareChangeLog"]].
1191	1191	When downloading the images, choose the required image file for download. ​
1192	1192
1193	1193