Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -62,6 +62,9 @@
62	62	* Firmware upgradable via UART interface
63	63	* Ultra-long RF range
64	64
	65	+
	66	+
	67	+
65	65	== 1.3  Specification ==
66	66
67	67	* CPU: 32-bit 48 MHz
...	...	@@ -82,6 +82,9 @@
82	82	* LoRa Rx current: <9 mA
83	83	* I/O Voltage: 3.3v
84	84
	88	+
	89	+
	90	+
85	85	== 1.4  AT Command ==
86	86
87	87
...	...	@@ -193,34 +193,59 @@
193	193
194	194	== 2.5  Example: Use AT Command to communicate with LA66 module via Arduino UNO. ==
195	195
196		-Show connection diagram：
197	197
	203	+**Show connection diagram：**
	204	+
	205	+
198	198	[[image:image-20220723170210-2.png||height="908" width="681"]]
199	199
200		-1.open Arduino IDE
201	201
	209	+
	210	+**1.  open Arduino IDE**
	211	+
	212	+
202	202	[[image:image-20220723170545-4.png]]
203	203
204		-2.Open project
205	205
	216	+
	217	+**2.  Open project**
	218	+
	219	+
	220	+LA66-LoRaWAN-shield-AT-command-via-Arduino-UNO source code link: [[https:~~/~~/www.dropbox.com/sh/trqitpm9adkupva/AAAE542NzwlHubIAIDxe6IWFa?dl=0>>https://www.dropbox.com/sh/trqitpm9adkupva/AAAE542NzwlHubIAIDxe6IWFa?dl=0]]
	221	+
206	206	[[image:image-20220723170750-5.png||height="533" width="930"]]
207	207
208		-3.Click the button marked 1 in the figure to compile, and after the compilation is complete, click the button marked 2 in the figure to upload
209	209
	225	+
	226	+**3.  Click the button marked 1 in the figure to compile, and after the compilation is complete, click the button marked 2 in the figure to upload**
	227	+
	228	+
210	210	[[image:image-20220723171228-6.png]]
211	211
212		-4.After the upload is successful, open the serial port monitoring and send the AT command
213	213
	232	+
	233	+**4.  After the upload is successful, open the serial port monitoring and send the AT command**
	234	+
	235	+
214	214	[[image:image-20220723172235-7.png||height="480" width="1027"]]
215	215
	238	+
	239	+
216	216	== 2.6  Example: Join TTN network and send an uplink message, get downlink message. ==
217	217
218		-1.Open project
219	219
	243	+**1.  Open project**
	244	+
	245	+
	246	+Join-TTN-network source code link: [[https:~~/~~/www.dropbox.com/sh/trqitpm9adkupva/AAAE542NzwlHubIAIDxe6IWFa?dl=0>>https://www.dropbox.com/sh/trqitpm9adkupva/AAAE542NzwlHubIAIDxe6IWFa?dl=0]]
	247	+
220	220	[[image:image-20220723172502-8.png]]
221	221
222		-2.Same steps as 2.5,after opening the serial port monitoring, it will automatically connect to the network and send packets
223	223
	251	+
	252	+2.  Same steps as 2.5,after opening the serial port monitoring, it will automatically connect to the network and send packets
	253	+
	254	+
224	224	[[image:image-20220723172938-9.png||height="652" width="1050"]]
225	225
226	226