Table of Contents:

1.  LA66 LoRaWAN Shield

1.1  Overview

image-20220715000826-2.png     

 

LA66 LoRaWAN Shield is the Arduino shield base on LA66. Users can use LA66 LoRaWAN Shield to rapidly add LoRaWAN or peer-to-peer LoRa wireless function to  Arduino projects.

LA66 is a ready-to-use module that includes the LoRaWAN v1.0.3 protocol. The LoRaWAN stack used in LA66 is used in more than 1 million LoRaWAN End Devices deployed world widely.  This mature LoRaWAN stack greatly reduces the risk to make stable LoRaWAN Sensors to support different LoRaWAN servers and different countries' standards. External MCU can use AT command to call LA66 and start to transmit data via the LoRaWAN protocol.

Each LA66 module includes a world-unique OTAA key for LoRaWAN registration.

Besides the support of the LoRaWAN protocol, LA66 also supports open-source peer-to-peer LoRa Protocol for the none-LoRaWAN application. 

LA66 is equipped with TCXO crystal which ensures the module can achieve stable performance in extreme temperatures.

1.2  Features

  • Arduino Shield base on LA66 LoRaWAN module
  • Support LoRaWAN v1.0.3 protocol
  • Support peer-to-peer protocol
  • TCXO crystal to ensure RF performance on low temperature
  • SMA connector
  • Available in different frequency LoRaWAN frequency bands.
  • World-wide unique OTAA keys.
  • AT Command via UART-TTL interface
  • Firmware upgradable via UART interface
  • Ultra-long RF range

1.3  Specification

  • CPU: 32-bit 48 MHz
  • Flash: 256KB
  • RAM: 64KB
  • Input Power Range: 1.8v ~ 3.7v
  • Power Consumption: < 4uA.
  • Frequency Range: 150 MHz ~ 960 MHz
  • Maximum Power +22 dBm constant RF output
  • High sensitivity: -148 dBm
  • Temperature:
    • Storage: -55 ~ +125℃
    • Operating: -40 ~ +85℃
  • Humidity:
    • Storage: 5 ~ 95% (Non-Condensing)
    • Operating: 10 ~ 95% (Non-Condensing)
  • LoRa Tx Current: <90 mA at +17 dBm, 108 mA at +22 dBm
  • LoRa Rx current: <9 mA
  • I/O Voltage: 3.3v

1.4  Pin Mapping & LED

image-20220817085048-1.png

1. The LED lights up red when there is an upstream data packet

2. When the network is successfully connected, the green light will be on for 5 seconds

3. Purple light on when receiving downlink data packets

image-20220820112305-1.png

1.5  Example: Use AT Command to communicate with LA66 module via Arduino UNO.

Show connection diagram:

image-20220723170210-2.png

1.  open Arduino IDE

image-20220723170545-4.png

2.  Open project

LA66-LoRaWAN-shield-AT-command-via-Arduino-UNO source code link: https://www.dropbox.com/sh/hgtycj0go4tka2r/AAACRRIRriMAudB2m3ThH7Sba?dl=0 

image-20220726135239-1.png

3.  Click the button marked 1 in the figure to compile, and after the compilation is complete, click the button marked 2 in the figure to upload

image-20220726135356-2.png

4.  After the upload is successful, open the serial port monitoring and send the AT command

image-20220723172235-7.png

1.6  Example: Join TTN network and send an uplink message, get downlink message.

1.  Open project

Join-TTN-network source code link: https://www.dropbox.com/sh/hgtycj0go4tka2r/AAACRRIRriMAudB2m3ThH7Sba?dl=0 

image-20220723172502-8.png

2.  Same steps as 1.5,after opening the serial port monitoring, it will automatically connect to the network and send packets

image-20220723172938-9.png

1.7  Example: Log Temperature Sensor(DHT11) and send data to TTN, show it in Node-RED.

1.  Open project

Log-Temperature-Sensor-and-send-data-to-TTN source code link: https://www.dropbox.com/sh/hgtycj0go4tka2r/AAACRRIRriMAudB2m3ThH7Sba?dl=0

image-20220723173341-10.png

2.  Same steps as 2.5,after opening the serial port monitoring, it will automatically connect to the network and send packets

image-20220723173950-11.png

3.  Integration into Node-red via TTNV3

For the usage of Node-RED, please refer to: http://wiki.dragino.com/xwiki/bin/view/Main/Node-RED/

image-20220723175700-12.png

1.8  Example: How to join helium

1.  Create a new device.

image-20220907165500-1.png

2.  Save the device after filling in the necessary information.

image-20220907165837-2.png

3.  Use AT commands.

image-20220602100052-2.png

4.  Use command AT+CFG to get device configuration

image-20220907170308-3.png

5.  Network successfully.

image-20220907170436-4.png

6.  Send uplink using command

image-20220912084334-1.png

image-20220912084412-3.png

image-20220907170744-6.png

1.9  Upgrade Firmware of LA66 LoRaWAN Shield

1.9.1  Items needed for update

  1. LA66 LoRaWAN Shield
  2. Arduino
  3. USB TO TTL Adapter

image-20220602100052-2.png

1.9.2  Connection

image-20220602101311-3.png

LA66 LoRaWAN Shield  <-> USB TTL

GND                                <-> GND
TXD                                 <->  TXD
RXD                                 <->  RXD

Put a jumper cap on JP6 of LA66 LoRaWAN Shield. ( the jumper is to power on LA66 module)

Connect USB TTL Adapter to PC after connecting the wires

image-20220602102240-4.png

1.9.3  Upgrade steps

1.  Switch SW1 to put in ISP position

image-20220602102824-5.png

2.  Press the RST switch once

image-20220817085447-1.png

3.  Open the Upgrade tool (Tremo Programmer) in PC and Upgrade

image-20220602103227-6.png

image-20220602103357-7.png

2.  Select the COM port corresponding to USB TTL

image-20220602103844-8.png

3.  Select the bin file to burn

image-20220602104144-9.png

image-20220602104251-10.png

image-20220602104402-11.png

4.  Click to start the download

image-20220602104923-13.png

5.  Check update process

image-20220602104948-14.png

The following picture shows that the burning is successful

image-20220602105251-15.png

2.  FAQ

2.1  How to Compile Source Code for LA66?

Compile and Upload Code to ASR6601 Platform :Instruction

2.2  Where to find Peer-to-Peer firmware of LA66?

Instruction for LA66 Peer to Peer firmware : Instruction 

3.  Order Info

Part Number:   LA66-LoRaWAN-Shield-XXX   

XXX: The default frequency band

  • AS923:  LoRaWAN AS923 band
  • AU915:  LoRaWAN AU915 band
  • EU433:  LoRaWAN EU433 band
  • EU868:  LoRaWAN EU868 band
  • KR920:  LoRaWAN KR920 band
  • US915:  LoRaWAN US915 band
  • IN865:  LoRaWAN IN865 band
  • CN470: LoRaWAN CN470 band
  • PP:        Peer to Peer LoRa Protocol

4.  Reference

  • Hardware Design File for LA66 LoRaWAN Shield : Download

5.  FCC Statement

FCC Caution:

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 

IMPORTANT NOTE: 

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 

—Reorient or relocate the receiving antenna. 

—Increase the separation between the equipment and receiver. 

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

—Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement: 

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.  

 

Tags:
    
Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0