WSC1-L-Dragino LoRaWAN Weather Station User Manual

Dragino LoRaWAN weather station series products are designed for measuring atmospheric conditions to provide information for weather forecasts and to study the (% style="color:#4472c4" %)**weather and climate**(%%). They consist of a (% style="color:#4472c4" %)**main process device (WSC1-L) and various sensors**.

25

)))

26

27

(((

28

The sensors include various type such as: (% style="color:#4472c4" %)**Rain Gauge**, **Temperature/Humidity/Pressure sensor**, **Wind Speed/direction sensor**, **Illumination sensor**, **CO2 sensor**, **Rain/Snow sensor**,** PM2.5/10 sensor**, **PAR(Photosynthetically Available Radiation) sensor, Total Solar Radiation sensor**(%%) and so on.

)))

(((

Main process device WSC1-L is an outdoor LoRaWAN RS485 end node. It is powered by external (% style="color:#4472c4" %)**12v solar power**(%%) and have a (% style="color:#4472c4" %)**built-in li-on backup battery**(%%). WSC1-L reads value from various sensors and upload these sensor data to IoT server via LoRaWAN wireless protocol.

)))

(((

WSC1-L is full compatible with(% style="color:#4472c4" %)** LoRaWAN Class C protocol**(%%), it can work with standard LoRaWAN gateway.

)))

= 2. How to use =

== 2.1 Installation ==

43

44

45

Below is an installation example for the weather station. Field installation example can be found at [[Appendix I: Field Installation Photo.>>||anchor="H11.AppendixI:FieldInstallationPhoto"]]

46

47

48

[[image:1656041948552-849.png]]

49

50

51

(% style="color:blue" %)** Wiring:**

52

53

~1. WSC1-L and sensors all powered by solar power via MPPT

54

55

2. WSC1-L and sensors connect to each other via RS485/Modbus.

56

57

3. WSC1-L read value from each sensor and send uplink via LoRaWAN

58

59

60

WSC1-L is shipped with a RS485 converter board, for the easy connection to different sensors and WSC1-L. Below is a connection photo:

61

62

63

[[image:1656042136605-251.png]]

64

65

66

(% style="color:red" %)**Notice 1:**

67

68

* All weather sensors and WSC1-L are powered by MPPT solar recharge controller. MPPT is connected to solar panel and storage battery.

69

* WSC1-L has an extra 1000mAh back up battery. So it can work even solar panel and storage battery Fails.

70

* Weather sensors won't work if solar panel and storage battery fails.

71

72

(% style="color:red" %)**Notice 2:**

73

74

Due to shipment and importation limitation, user is better to purchase below parts locally:

* Solar Panel

* Storage Battery

* MPPT Solar Recharger

79

* Mounting Kit includes pole and mast assembly. Each weather sensor has it's own mounting assembly, user can check the sensor section in this manual.

* Cabinet.

== 2.2 How it works? ==

(((

Each WSC1-L is shipped with a worldwide unique set of OTAA keys. To use WSC1-L in a LoRaWAN network, user needs to input the OTAA keys in LoRaWAN network server. After finish installation as above. Create WSC1-L in your LoRaWAN server and Power on WSC1-L , it can join the LoRaWAN network and start to transmit sensor data. The default period for each uplink is 20 minutes.

)))

(((

Open WSC1-L and put the yellow jumper as below position to power on WSC1-L.

94

)))

95

96

[[image:1656042192857-709.png]]

97

98

99

(% style="color:red" %)**Notice:**

100

101

1. WSC1-L will auto scan available weather sensors when power on or reboot.

102

1. User can send a [[downlink command>>||anchor="H3.ConfigureWSC1-LviaATCommandorLoRaWANDownlink"]] to WSC1-L to do a re-scan on the available sensors.

== 2.3 Example to use for LoRaWAN network ==

107

108

109

This section shows an example for how to join the TTN V3 LoRaWAN IoT server. Usages with other LoRaWAN IoT servers are of similar procedure.

110

111

112

[[image:1656042612899-422.png]]

Assume the DLOS8 is already set to connect to [[TTN V3 network >>url:https://eu1.cloud.thethings.network/]]. We need to add the WSC1-L device in TTN V3:

117

118

119

(% style="color:blue" %)**Step 1**(%%): Create a device in TTN V3 with the OTAA keys from WSC1-L.

120

121

Each WSC1-L is shipped with a sticker with the default device EUI as below:

122

123

[[image:image-20220624115043-1.jpeg]]

124

125

126

User can enter these keys in the LoRaWAN Server portal. Below is TTN V3 screen shot:

127

128

Put a Jumper on JP2 to power on the device. ( The Jumper must be in FLASH position).

129

130

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSE01-LoRaWAN%20Soil%20Moisture%20%26%20EC%20Sensor%20User%20Manual/WebHome/image-20220606163915-7.png?rev=1.1||alt="image-20220606163915-7.png"]]

131

132

**Add APP EUI in the application.**

133

134

[[image:1656042662694-311.png]]

135

136

[[image:1656042673910-429.png]]

**Choose Manually to add WSC1-L**

142

143

[[image:1656042695755-103.png]]

**Add APP KEY and DEV EUI**

148

149

[[image:1656042723199-746.png]]

(((

(% style="color:blue" %)**Step 2**(%%): Power on WSC1-L, it will start to join TTN server. After join success, it will start to upload sensor data to TTN V3 and user can see in the panel.

)))

[[image:1656042745346-283.png]]

159

160

161

== 2.4 Uplink Payload ==

162

163

164

Uplink payloads include two types: Valid Sensor Value and other status / control command.

165

166

* Valid Sensor Value: Use FPORT=2

167

* Other control command: Use FPORT other than 2.

=== 2.4.1 Uplink FPORT~=5, Device Status ===

172

173

174

Uplink the device configures with FPORT=5. Once WSC1-L Joined the network, it will uplink this message to the server. After first uplink, WSC1-L will uplink Device Status every 12 hours

(((

User can also use downlink command**(0x2301)** to ask WSC1-L to resend this uplink

179

)))

180

181

(% border="1" cellspacing="8" style="background-color:#ffffcc; color:green; width:500px" %)

182

183

|(% style="width:99px" %)**Value**|(% style="width:112px" %)[[Sensor Model>>||anchor="HSensorModel:"]]|(% style="width:135px" %)[[Firmware Version>>||anchor="HFirmwareVersion:"]]|(% style="width:126px" %)[[Frequency Band>>||anchor="HFrequencyBand:"]]|(% style="width:85px" %)[[Sub-band>>||anchor="HSub-Band:"]]|(% style="width:46px" %)[[BAT>>||anchor="HBAT:"]]|(% style="width:166px" %)[[Weather Sensor Types>>||anchor="HWeatherSensorTypes:"]]

184

185

[[image:1656043061044-343.png]]

186

187

188

Example Payload (FPort=5): [[image:image-20220624101005-1.png]]

189

190

191

==== (% style="color:#037691" %)**Sensor Model:**(%%) ====

192

193

For WSC1-L, this value is 0x0D.

194

195

196

==== (% style="color:#037691" %)**Firmware Version:**(%%) ====

197

198

0x0100, Means: v1.0.0 version.

199

200

201

==== (% style="color:#037691" %)**Frequency Band:**(%%) ====

*0x01: EU868

*0x02: US915

*0x03: IN865

*0x04: AU915

*0x05: KZ865

*0x06: RU864

*0x07: AS923

*0x08: AS923-1

*0x09: AS923-2

*0x0a: AS923-3

==== (% style="color:#037691" %)**Sub-Band:**(%%) ====

225

226

value 0x00 ~~ 0x08(only for CN470, AU915,US915. Others are0x00)

227

228

229

==== (% style="color:#037691" %)**BAT:**(%%) ====

230

231

(((

232

shows the battery voltage for WSC1-L MCU.

)))

(((

Ex1: 0x0BD6/1000 = 3.03 V

)))

==== (% style="color:#037691" %)**Weather Sensor Types:**(%%) ====

241

242

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:100px" %)

243

|Byte3|Byte2|Byte1

244

245

Bit = 1 means this sensor is connected, Bit=0 means this sensor is not connected

246

247

[[image:image-20220624134713-1.png]]

248

249

250

Eg: 0x1000FE = 1 0000 0000 0000 1111 1110(b)

251

252

External sensors detected by WSC1-L include :

custom sensor A1,

PAR sensor (WSS-07),

Total Solar Radiation sensor (WSS-06),

259

260

CO2/PM2.5/PM10 (WSS-03),

261

262

Wind Speed/Direction (WSS-02)

263

264

265

User can also use downlink command(0x26 01) to ask WSC1-L to resend this uplink :

266

267

(% style="color:#037691" %)**Downlink:0x26 01**

268

269

[[image:1656049673488-415.png]]

270

271

272

=== 2.4.2 Uplink FPORT~=2, Real time sensor value ===

(((

WSC1-L will send this uplink after Device Config uplink once join LoRaWAN network successfully. And it will periodically send this uplink. Default interval is 20 minutes and [[can be changed>>||anchor="H3.1SetTransmitIntervalTime"]].

)))

(((

Uplink uses FPORT=2 and every 20 minutes send one uplink by default.

)))

(((

The upload length is dynamic, depends on what type of weather sensors are connected. The uplink payload is combined with sensor segments. As below:

)))

(% style="color:#4472c4" %)** Uplink Payload**:

290

291

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:464px" %)

292

|(% style="width:140px" %)Sensor Segment 1|(% style="width:139px" %)Sensor Segment 2|(% style="width:42px" %)……|(% style="width:140px" %)Sensor Segment n

293

294

(% style="color:#4472c4" %)** Sensor Segment Define**:

295

296

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:330px" %)

297

|(% style="width:89px" %)Type Code|(% style="width:114px" %)Length (Bytes)|(% style="width:124px" %)Measured Value

298

299

(% style="color:#4472c4" %)**Sensor Type Table:**

300

301

[[image:image-20220706154434-1.png]]

(((

Below is an example payload: [[image:image-20220624140615-3.png]]

)))

(((

)))

(((

When sending this payload to LoRaWAN server. WSC1-L will send this in one uplink or several uplinks according to LoRaWAN spec requirement. For example, total length of Payload is 54 bytes.

)))

* (((

When WSC1-L sending in US915 frequency DR0 data rate. Because this data rate has limitation of 11 bytes payload for each uplink. The payload will be split into below packets and uplink.

)))

(((

Uplink 1: [[image:image-20220624140735-4.png]]

)))

(((

)))

(((

Uplink 2: [[image:image-20220624140842-5.png]]

)))

(((

)))

* (((

When WSC1-L sending in EU868 frequency DR0 data rate. The payload will be split into below packets and uplink:

)))

(((

Uplink 1: [[image:image-20220624141025-6.png]]

)))

(((

)))

Uplink 2: [[image:image-20220624141100-7.png]]

349

350

351

=== 2.4.3 Decoder in TTN V3 ===

(((

In LoRaWAN platform, user only see HEX payload by default, user needs to use payload formatters to decode the payload to see human-readable value.

)))

(((

Download decoder for suitable platform from: [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>https://github.com/dragino/dragino-end-node-decoder]]

)))

(((

)))

(((

and put as below:

)))

[[image:1656051152438-578.png]]

373

374

375

== 2.5 Show data on Application Server ==

(((

Application platform provides a human friendly interface to show the sensor data, once we have sensor data in TTN V3, we can use Datacake to connect to TTN V3 and see the data in Datacake. Below are the steps:

)))

(((

)))

(((

(% style="color:blue" %)**Step 1**(%%): Be sure that your device is programmed and properly connected to the LoRaWAN network.

)))

(((

(% style="color:blue" %)**Step 2**(%%): Configure your Application to forward data to Datacake you will need to add integration. Go to TTN V3 Console ~-~-> Applications ~-~-> Integrations ~-~-> Add Integrations.

392

)))

393

394

[[image:1656051197172-131.png]]

**Add TagoIO:**

[[image:1656051223585-631.png]]

**Authorization:**

[[image:1656051248318-368.png]]

In TagoIO console ([[https:~~/~~/admin.tago.io~~/~~/>>url:https://datacake.co/]]) , add WSC1-L:

411

412

413

[[image:1656051277767-168.png]]

414

415

416

= 3. Configure WSC1-L via AT Command or LoRaWAN Downlink =

417

418

419

Use can configure WSC1-L via AT Command or LoRaWAN Downlink.

420

421

* AT Command Connection: See [[FAQ>>||anchor="H7.FAQ"]].

422

* LoRaWAN Downlink instruction for different platforms: [[Use Note for Server>>doc:Main.WebHome]](IoT LoRaWAN Server)

423

424

There are two kinds of commands to configure WSC1-L, they are:

425

426

* (% style="color:#4472c4" %)**General Commands**.

427

428

These commands are to configure:

429

430

* General system settings like: uplink interval.

431

* LoRaWAN protocol & radio related command.

432

433

They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack((% style="color:red" %)Note~*~*)(%%). These commands can be found on the wiki: [[End Device Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]

434

435

(% style="color:red" %)**Note~*~*: Please check early user manual if you don’t have v1.8.0 firmware. **

436

437

438

* (% style="color:#4472c4" %)**Commands special design for WSC1-L**

439

440

These commands only valid for WSC1-L, as below:

441

442

443

== 3.1 Set Transmit Interval Time ==

444

445

446

Feature: Change LoRaWAN End Node Transmit Interval.

447

448

(% style="color:#037691" %)**AT Command: AT+TDC**

449

450

[[image:image-20220624142619-8.png]]

451

452

453

(% style="color:#037691" %)**Downlink Command: 0x01**

454

455

Format: Command Code (0x01) followed by 3 bytes time value.

456

457

If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.

458

459

* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds

460

* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds

== 3.2 Set Emergency Mode ==

465

466

467

Feature: In emergency mode, WSC1-L will uplink data every 1 minute.

468

469

(% style="color:#037691" %)**AT Command:**

470

471

[[image:image-20220624142956-9.png]]

472

473

474

(% style="color:#037691" %)**Downlink Command:**

475

476

* 0xE101 Same as: AT+ALARMMOD=1

477

* 0xE100 Same as: AT+ALARMMOD=0

== 3.3 Add or Delete RS485 Sensor ==

(((

Feature: User can add or delete 3^^rd^^ party sensor as long they are RS485/Modbus interface,baud rate support 9600.Maximum can add 4 sensors.

)))

(((

(% style="color:#037691" %)**AT Command: **

)))

(((

(% style="color:blue" %)**AT+DYSENSOR=Type_Code, Query_Length, Query_Command , Read_Length , Valid_Data ,has_CRC,timeout**

)))

* (((

Type_Code range: A1 ~~ A4

498

)))

499

* (((

500

Query_Length: RS485 Query frame length, Value cannot be greater than 10

501

)))

502

* (((

503

Query_Command: RS485 Query frame data to be sent to sensor, cannot be larger than 10 bytes

504

)))

505

* (((

506

Read_Length: RS485 response frame length supposed to receive. Max can receive

507

)))

508

* (((

509

Valid_Data: valid data from RS485 Response, Valid Data will be added to Payload and upload via LoRaWAN.

510

)))

511

* (((

512

has_CRC: RS485 Response crc check (0: no verification required 1: verification required). If CRC=1 and CRC error, valid data will be set to 0.

513

)))

514

* (((

515

timeout: RS485 receive timeout (uint:ms). Device will close receive window after timeout

)))

(((

**Example:**

)))

(((

User need to change external sensor use the type code as address code.

)))

(((

With a 485 sensor, after correctly changing the address code to A1, the RS485 query frame is shown in the following table:

528

)))

529

530

[[image:image-20220624143553-10.png]]

531

532

533

The response frame of the sensor is as follows:

534

535

[[image:image-20220624143618-11.png]]

536

537

538

**Then the following parameters should be:**

539

540

* Address_Code range: A1

541

* Query_Length: 8

542

* Query_Command: A103000000019CAA

543

* Read_Length: 8

544

* Valid_Data: 24 (Indicates that the data length is 2 bytes, starting from the 4th byte)

545

* has_CRC: 1

546

* timeout: 1500 (Fill in the test according to the actual situation)

547

548

**So the input command is:**

549

550

AT+DYSENSOR=A1,8,A103000000019CAA,8,24,1,1500

551

552

553

In every sampling. WSC1-L will auto append the sensor segment as per this structure and uplink.

554

555

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:351px" %)

556

|=(% style="width: 94px;" %)Type Code|=(% style="width: 121px;" %)Length (Bytes)|=(% style="width: 132px;" %)Measured Value

557

|(% style="width:94px" %)A1|(% style="width:121px" %)2|(% style="width:132px" %)0x000A

558

559

**Related commands:**

560

561

AT+DYSENSOR=A1,0 ~-~-> Delete 3^^rd^^ party sensor A1.

562

563

AT+DYSENSOR ~-~-> List All 3^^rd^^ Party Sensor. Like below:

564

565

566

(% style="color:#037691" %)**Downlink Command: **

567

568

**delete custom sensor A1:**

569

570

* 0xE5A1 Same as: AT+DYSENSOR=A1,0

571

572

**Remove all custom sensors**

* 0xE5FF

== 3.4 RS485 Test Command ==

579

580

581

(% style="color:#037691" %)**AT Command:**

582

583

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:474px" %)

584

|=(% style="width: 159px;" %)**Command Example**|=(% style="width: 227px;" %)**Function**|=(% style="width: 85px;" %)**Response**

585

|(% style="width:159px" %)AT+RSWRITE=xxxxxx|(% style="width:227px" %)(((

586

(((

587

Send command to 485 sensor

)))

(((

Range : no more than 10 bytes

592

)))

593

)))|(% style="width:85px" %)OK

594

595

Eg: Send command **01 03 00 00 00 01 84 0A** to 485 sensor

596

597

AT+RSWRITE=0103000001840A

598

599

600

(% style="color:#037691" %)**Downlink Command:**

601

602

* 0xE20103000001840A Same as: AT+RSWRITE=0103000001840A

== 3.5 RS485 response timeout ==

607

608

609

Feature: Set or get extended time to receive 485 sensor data.

610

611

(% style="color:#037691" %)**AT Command:**

612

613

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:433px" %)

614

|=(% style="width: 157px;" %)**Command Example**|=(% style="width: 188px;" %)**Function**|=(% style="width: 85px;" %)**Response**

615

|(% style="width:157px" %)AT+DTR=1000|(% style="width:188px" %)(((

616

(((

617

Set response timeout to:

)))

(((

Range : 0~~10000

)))

)))|(% style="width:85px" %)OK

624

625

(% style="color:#037691" %)**Downlink Command:**

626

627

Format: Command Code (0xE0) followed by 3 bytes time value.

628

629

If the downlink payload=E0000005, it means set the END Node’s Transmit Interval to 0x000005=5(S), while type code is E0.

630

631

* Example 1: Downlink Payload: E0000005 ~/~/ Set Transmit Interval (DTR) = 5 seconds

632

* Example 2: Downlink Payload: E000000A ~/~/ Set Transmit Interval (DTR) = 10 seconds

== 3.6 Set Sensor Type ==

(((

Feature: Set sensor in used. If there are 6 sensors, user can set to only send 5 sensors values.

)))

(((

See [[definition>>||anchor="HWeatherSensorTypes:"]] for the sensor type.

645

)))

646

647

[[image:image-20220624144904-12.png]]

648

649

650

(% style="color:#037691" %)**AT Command:**

651

652

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:377px" %)

653

|=(% style="width: 157px;" %)**Command Example**|=(% style="width: 130px;" %)**Function**|=(% style="width: 87px;" %)**Response**

654

|(% style="width:157px" %)AT+STYPE=80221|(% style="width:130px" %)Set sensor types|(% style="width:87px" %)OK

655

656

Eg: The setting command **AT+STYPE=80221** means:

657

658

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:495px" %)

So wsc1-L will upload the following data: Custom Sensor A1, Rain Gauge,CO2,BAT.

667

668

669

(% style="color:#037691" %)**Downlink Command:**

670

671

* 0xE400080221 Same as: AT+STYPE=80221

672

673

(% style="color:red" %)**Note:**

674

675

~1. The sensor type will not be saved to flash, and the value will be updated every time the sensor is restarted or rescanned.

676

677

678

= 4. Power consumption and battery =

679

680

== 4.1 Total Power Consumption ==

681

682

683

Dragino Weather Station serial products include the main process unit ( WSC1-L ) and various sensors. The total power consumption equal total power of all above units. The power consumption for main process unit WSC1-L is 18ma @ 12v. and the power consumption of each sensor can be found on the Sensors chapter.

684

685

686

== 4.2 Reduce power consumption ==

687

688

689

The main process unit WSC1-L is set to LoRaWAN Class C by default. If user want to reduce the power consumption of this unit, user can set it to run in Class A. In Class A mode, WSC1-L will not be to get real-time downlink command from IoT Server.

== 4.3 Battery ==

(((

All sensors are only power by external power source. If external power source is off. All sensor won't work.

)))

(((

Main Process Unit WSC1-L is powered by both external power source and internal 1000mAh rechargeable battery. If external power source is off, WSC1-L still runs and can send periodically uplinks, but the sensors value will become invalid. External power source can recharge the 1000mAh rechargeable battery.

)))

= 5. Main Process Unit WSC1-L =

== 5.1 Features ==

* Wall Attachable.

* LoRaWAN v1.0.3 Class A protocol.

711

* RS485 / Modbus protocol

712

* Frequency Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915

713

* AT Commands to change parameters

714

* Remote configure parameters via LoRaWAN Downlink

715

* Firmware upgradable via program port

716

* Powered by external 12v battery

717

* Back up rechargeable 1000mAh battery

718

* IP Rating: IP65

719

* Support default sensors or 3rd party RS485 sensors

== 5.2 Power Consumption ==

724

725

726

WSC1-L (without external sensor): Idle: 4mA, Transmit: max 40mA

727

728

729

== 5.3 Storage & Operation Temperature ==

-20°C to +60°C

== 5.4 Pin Mapping ==

736

737

738

[[image:1656054149793-239.png]]

== 5.5 Mechanical ==

Refer LSn50v2 enclosure drawing in: [[https:~~/~~/www.dropbox.com/sh/0ir0l9jjmk6p95e/AADwWXorcKuNpPR5em7VgrEja?dl=0>>https://www.dropbox.com/sh/0ir0l9jjmk6p95e/AADwWXorcKuNpPR5em7VgrEja?dl=0]]

745

746

747

== 5.6 Connect to RS485 Sensors ==

748

749

750

WSC1-L includes a RS485 converter PCB. Which help it easy to connect multiply RS485 sensors. Below is the photo for reference.

751

752

753

[[image:1656054389031-379.png]]

754

755

756

Hardware Design for the Converter Board please see:

757

758

[[https:~~/~~/www.dropbox.com/sh/bqyvsvitb70qtgf/AABLpD7_yxsQ_drVMxHIEI7wa?dl=0>>https://www.dropbox.com/sh/bqyvsvitb70qtgf/AABLpD7_yxsQ_drVMxHIEI7wa?dl=0]]

759

760

761

= 6. Weather Sensors =

762

763

== 6.1 Rain Gauge ~-~- WSS-01 ==

(((

WSS-01 RS485 Rain Gauge is used in meteorology and hydrology to gather and measure the amount of liquid precipitation (mainly rainfall) over an area.

)))

(((

WSS-01 uses a tipping bucket to detect rainfall. The tipping bucket use 3D streamline shape to make sure it works smoothly and is easy to clean.

)))

(((

WSS-01 is designed to support the Dragino Weather station solution. Users only need to connect WSS-01 RS485 interface to WSC1-L. The weather station main processor WSC1-L can detect and upload the rainfall to the IoT Server via wireless LoRaWAN protocol

)))

(((

The tipping bucket of WSS-01 is adjusted to the best angle. When installation, user only needs to screw up and adjust the bottom horizontally.

)))

(((

WSS-01 package includes screw which can be installed to ground. If user want to install WSS-01 on pole, they can purchase WS-K2 bracket kit.

)))

=== 6.1.1 Feature ===

* RS485 Rain Gauge

* Small dimension, easy to install

792

* Vents under funnel, avoid leaf or other things to avoid rain flow.

793

* ABS enclosure.

794

* Horizontal adjustable.

=== 6.1.2 Specification ===

* Resolution: 0.2mm

* Accuracy: ±3%

* Range: 0 ~~ 100mm

* Rainfall strength: 0mm～4mm/min (max 8mm/min)

805

* Input Power: DC 5~~24v

806

* Interface: RS485

807

* Working Temperature: 0℃～70℃ ( incorrect below 0 degree, because water become ICE)

808

* Working Humidity: <100% (no dewing)

809

* Power Consumption: 4mA @ 12v.

=== 6.1.3 Dimension ===

814

815

816

[[image:1656054957406-980.png]]

817

818

819

=== 6.1.4 Pin Mapping ===

820

821

822

[[image:1656054972828-692.png]]

823

824

825

=== 6.1.5 Installation Notice ===

(((

Do not power on while connect the cables. Double check the wiring before power on.

)))

(((

Installation Photo as reference:

)))

(((

(% style="color:#4472c4" %)** Install on Ground:**

)))

(((

WSS-01 Rain Gauge include screws so can install in ground directly .

)))

(((

(% style="color:#4472c4" %)** Install on pole:**

)))

(((

If user want to install on pole, they can purchase the (% style="color:#4472c4" %)** WS-K2 : Bracket Kit for Pole installation**(%%), and install as below:

852

)))

853

854

[[image:image-20220624152218-1.png||height="526" width="276"]]

855

856

WS-K2: Bracket Kit for Pole installation

857

858

859

WSSC-K2 dimension document, please see:

860

861

[[https:~~/~~/www.dropbox.com/sh/7wa2elfm2q8xq4l/AAB7ZB_gSVGrhmJEgU2LyTQNa?dl=0>>https://www.dropbox.com/sh/7wa2elfm2q8xq4l/AAB7ZB_gSVGrhmJEgU2LyTQNa?dl=0]]

862

863

864

== 6.2 Wind Speed/Direction ~-~- WSS-02 ==

865

866

867

[[image:1656055444035-179.png]]

(((

WSS-02 is a RS485 wind speed and wind direction monitor designed for weather station solution.

)))

(((

WSS-02 shell is made of polycarbonate composite material, which has good anti-corrosion and anti-corrosion characteristics, and ensure the long-term use of the sensor without rust. At the same time, it cooperates with the internal smooth bearing system to ensure the stability of information collection

)))

(((

Users only need to connect WSS-02 RS485 interface to WSC1-L. The weather station main processor WSC1-L can detect and upload the wind speed and direction to the IoT Server via wireless LoRaWAN protocol.

)))

=== 6.2.1 Feature ===

885

886

887

* RS485 wind speed / direction sensor

888

* PC enclosure, resist corrosion

=== 6.2.2 Specification ===

893

894

895

* Wind speed range: 0 ~~ 60m/s

896

* Wind direction range: 0 ~~ 360°

897

* Start wind speed: ≤0.3m/s

898

* Accuracy: ±（0.3＋0.03V）m/s , ±1°

899

* Input Power: DC 5~~24v

900

* Interface: RS485

901

* Working Temperature: -30℃～70℃

902

* Working Humidity: <100% (no dewing)

903

* Power Consumption: 13mA ~~ 12v.

904

* Cable Length: 2 meters

=== 6.2.3 Dimension ===

909

910

911

[[image:image-20220624152813-2.png]]

912

913

914

=== 6.2.4 Pin Mapping ===

915

916

917

[[image:1656056281231-994.png]]

918

919

920

=== 6.2.5 Angle Mapping ===

921

922

923

[[image:1656056303845-585.png]]

924

925

926

=== 6.2.6 Installation Notice ===

(((

Do not power on while connect the cables. Double check the wiring before power on.

)))

(((

The sensor must be installed with below direction, towards North.

)))

[[image:image-20220624153901-3.png]]

940

941

942

== 6.3 CO2/PM2.5/PM10 ~-~- WSS-03 ==

(((

WSS-03 is a RS485 Air Quality sensor. It can monitor CO2, PM2.5 and PM10 at the same time.

)))

(((

WSS-03 uses weather proof shield which can make sure the sensors are well protected against UV & radiation.

)))

(((

WSS-03 is designed to support the Dragino Weather station solution. Users only need to connect WSS-03 RS485 interface to WSC1-L. The weather station main processor WSC1-L can detect and upload the environment CO2, PM2.5 and PM10 to the IoT Server via wireless LoRaWAN protocol.

)))

=== 6.3.1 Feature ===

959

960

961

* RS485 CO2, PM2.5, PM10 sensor

962

* NDIR to measure CO2 with Internal Temperature Compensation

963

* Laser Beam Scattering to PM2.5 and PM10

=== 6.3.2 Specification ===

968

969

970

* CO2 Range: 0～5000ppm, accuracy: ±3%F•S（25℃）

971

* CO2 resolution: 1ppm

972

* PM2.5/PM10 Range: 0～1000μg/m3 , accuracy ±3%F•S（25℃）

973

* PM2.5/PM10 resolution: 1μg/m3

974

* Input Power: DC 7 ~~ 24v

975

* Preheat time: 3min

976

* Interface: RS485

977

* Working Temperature:

978

** CO2: 0℃～50℃;

979

** PM2.5/PM10: -30 ~~ 50℃

980

* Working Humidity:

981

** PM2.5/PM10: 15～80%RH (no dewing)

982

** CO2: 0～95%RH

983

* Power Consumption: 50mA@ 12v.

=== 6.3.3 Dimension ===

988

989

990

[[image:1656056708366-230.png]]

=== 6.3.4 Pin Mapping ===

995

996

997

[[image:1656056722648-743.png]]

998

999

1000

=== 6.3.5 Installation Notice ===

1001

1002

1003

Do not power on while connect the cables. Double check the wiring before power on.

1004

1005

1006

[[image:1656056751153-304.png]]

1007

1008

1009

[[image:1656056766224-773.png]]

1010

1011

1012

== 6.4 Rain/Snow Detect ~-~- WSS-04 ==

(((

WSS-04 is a RS485 rain / snow detect sensor. It can monitor Rain or Snow event.

)))

(((

WSS-04 has auto heating feature, this ensures measurement more reliable.

)))

(((

WSS-04 is designed to support the Dragino Weather station solution. Users only need to connect WSS-04 RS485 interface to WSC1-L. The weather station main processor WSC1-L can detect and upload the SNOW/Rain Event to the IoT Server via wireless LoRaWAN protocol.

)))

=== 6.4.1 Feature ===

1029

1030

1031

* RS485 Rain/Snow detect sensor

1032

* Surface heating to dry

1033

* grid electrode uses Electroless Nickel/Immersion Gold design for resist corrosion

=== 6.4.2 Specification ===

1038

1039

1040

* Detect if there is rain or snow

1041

* Input Power: DC 12 ~~ 24v

1042

* Interface: RS485

1043

* Working Temperature: -30℃～70℃

1044

* Working Humidity: 10～90%RH

1045

* Power Consumption:

1046

** No heating: 12mA @ 12v,

1047

** heating: 94ma @ 12v.

=== 6.4.3 Dimension ===

1052

1053

1054

[[image:1656056844782-155.png]]

1055

1056

1057

=== 6.4.4 Pin Mapping ===

1058

1059

1060

[[image:1656056855590-754.png]]

1061

1062

1063

=== 6.4.5 Installation Notice ===

1064

1065

1066

Do not power on while connect the cables. Double check the wiring before power on.

(((

Install with 15°degree.

1071

)))

1072

1073

[[image:1656056873783-780.png]]

1074

1075

1076

[[image:1656056883736-804.png]]

1077

1078

1079

=== 6.4.6 Heating ===

(((

WSS-04 supports auto-heat feature. When the temperature is below the heat start temperature 15℃, WSS-04 starts to heat and stop at stop temperature (default is 25℃).

)))

== 6.5 Temperature, Humidity, Illuminance, Pressure ~-~- WSS-05 ==

(((

WSS-05 is a 4 in 1 RS485 sensor which can monitor Temperature, Humidity, Illuminance and Pressure at the same time.

)))

(((

WSS-05 is designed to support the Dragino Weather station solution. Users only need to connect WSS-05 RS485 interface to WSC1-L. The weather station main processor WSC1-L can detect and upload environment Temperature, Humidity, Illuminance, Pressure to the IoT Server via wireless LoRaWAN protocol.

)))

=== 6.5.1 Feature ===

1100

1101

1102

* RS485 Temperature, Humidity, Illuminance, Pressure sensor

=== 6.5.2 Specification ===

1107

1108

1109

* Input Power: DC 12 ~~ 24v

1110

* Interface: RS485

1111

* Temperature Sensor Spec:

** Range: -30 ~~ 70℃

** resolution 0.1℃

** Accuracy: ±0.5℃

* Humidity Sensor Spec:

1116

** Range: 0 ~~ 100% RH

1117

** resolution 0.1 %RH

1118

** Accuracy: 3% RH

1119

* Pressure Sensor Spec:

1120

** Range: 10～1100hPa

1121

** Resolution: 0.1hPa

1122

** Accuracy: ±0.1hPa

1123

* Illuminate sensor:

1124

** Range: 0～2/20/200kLux

1125

** Resolution: 10 Lux

1126

** Accuracy: ±3％FS

1127

* Working Temperature: -30℃～70℃

1128

* Working Humidity: 10～90%RH

1129

* Power Consumption: 4mA @ 12v

=== 6.5.3 Dimension ===

1134

1135

1136

[[image:1656057170639-522.png]]

1137

1138

1139

=== 6.5.4 Pin Mapping ===

1140

1141

1142

[[image:1656057181899-910.png]]

1143

1144

1145

=== 6.5.5 Installation Notice ===

1146

1147

1148

Do not power on while connect the cables. Double check the wiring before power on.

1149

1150

[[image:1656057199955-514.png]]

1151

1152

1153

[[image:1656057212438-475.png]]

1154

1155

1156

== 6.6 Total Solar Radiation sensor ~-~- WSS-06 ==

(((

WSS-06 is Total Radiation Sensor can be used to measure the total solar radiation in the spectral range of 0.3 to 3 μm (300 to 3000 nm). If the sensor face is down, the reflected radiation can be measured, and the shading ring can also be used to measure the scattered radiation.

)))

(((

The core device of the radiation sensor is a high-precision photosensitive element, which has good stability and high precision; at the same time, a precision-machined PTTE radiation cover is installed outside the sensing element, which effectively prevents environmental factors from affecting its performance

)))

(((

WSS-06 is designed to support the Dragino Weather station solution. Users only need to connect WSS-06 RS485 interface to WSC1-L. The weather station main processor WSC1-L can detect and upload Total Solar Radiation to the IoT Server via wireless LoRaWAN protocol.

)))

=== 6.6.1 Feature ===

1173

1174

1175

* RS485 Total Solar Radiation sensor

1176

* Measure Total Radiation between 0.3～3μm（300～3000nm）

1177

* Measure Reflected Radiation if sense area towards ground.

=== 6.6.2 Specification ===

1182

1183

1184

* Input Power: DC 5 ~~ 24v

1185

* Interface: RS485

1186

* Detect spectrum: 0.3～3μm（300～3000nm）

1187

* Measure strength range: 0～2000W/m2

1188

* Resolution: 0.1W/m2

1189

* Accuracy: ±3%

1190

* Yearly Stability: ≤±2％

1191

* Cosine response: ≤7％ (@ Sun angle 10°)

1192

* Temperature Effect: ±2％（－10℃～40℃）

1193

* Working Temperature: -40℃～70℃

1194

* Working Humidity: 10～90%RH

1195

* Power Consumption: 4mA @ 12v

=== 6.6.3 Dimension ===

1200

1201

1202

[[image:1656057348695-898.png]]

1203

1204

1205

=== 6.6.4 Pin Mapping ===

1206

1207

1208

[[image:1656057359343-744.png]]

1209

1210

1211

=== 6.6.5 Installation Notice ===

1212

1213

1214

Do not power on while connect the cables. Double check the wiring before power on.

1215

1216

1217

[[image:1656057369259-804.png]]

1218

1219

1220

[[image:1656057377943-564.png]]

1221

1222

1223

== 6.7 PAR (Photosynthetically Available Radiation) ~-~- WSS-07 ==

(((

WSS-07 photosynthetically active radiation sensor is mainly used to measure the photosynthetically active radiation of natural light in the wavelength range of 400-700nm.

)))

(((

WSS-07 use precision optical detectors and has an optical filter of 400-700nm, when natural light is irradiated, a voltage signal proportional to the intensity of the incident radiation is generated, and its luminous flux density is proportional to the cosine of the direct angle of the incident light.

)))

(((

WSS-07 is designed to support the Dragino Weather station solution. Users only need to connect WSS-07 RS485 interface to WSC1-L. The weather station main processor WSC1-L can detect and upload Photosynthetically Available Radiation to the IoT Server via wireless LoRaWAN protocol.

)))

=== 6.7.1 Feature ===

(((

PAR (Photosynthetically Available Radiation) sensor measure 400 ~~ 700nm wavelength nature light's Photosynthetically Available Radiation.

)))

(((

When nature light shine on the sense area, it will generate a signal base on the incidence radiation strength.

)))

=== 6.7.2 Specification ===

1252

1253

1254

* Input Power: DC 5 ~~ 24v

1255

* Interface: RS485

1256

* Response Spectrum: 400～700nm

1257

* Measure range: 0～2500μmol/m2•s

1258

* Resolution: 1μmol/m2•s

1259

* Accuracy: ±2%

1260

* Yearly Stability: ≤±2％

1261

* Working Temperature: -30℃～75℃

1262

* Working Humidity: 10～90%RH

1263

* Power Consumption: 3mA @ 12v

=== 6.7.3 Dimension ===

1268

1269

1270

[[image:1656057538793-888.png]]

1271

1272

1273

=== 6.7.4 Pin Mapping ===

1274

1275

1276

[[image:1656057548116-203.png]]

1277

1278

1279

=== 6.7.5 Installation Notice ===

1280

1281

1282

Do not power on while connect the cables. Double check the wiring before power on.

1283

1284

1285

[[image:1656057557191-895.png]]

1286

1287

1288

[[image:1656057565783-251.png]]

= 7. FAQ =

== 7.1 What else do I need to purchase to build Weather Station? ==

1294

1295

1296

Below is the installation photo and structure:

1297

1298

1299

[[image:1656057598349-319.png]]

1300

1301

1302

[[image:1656057608049-693.png]]

1303

1304

1305

== 7.2 How to upgrade firmware for WSC1-L? ==

(((

Firmware Location & Change log:

1310

1311

[[https:~~/~~/www.dropbox.com/sh/fuorz31grv8i3r1/AABmjFDU4FADNP6sq7fsmBwVa?dl=0>>https://www.dropbox.com/sh/fuorz31grv8i3r1/AABmjFDU4FADNP6sq7fsmBwVa?dl=0]]

)))

(((

)))

(((

Firmware Upgrade instruction: [[Firmware Upgrade Instruction>>doc:Main.Firmware Upgrade Instruction for STM32 base products.WebHome||anchor="H2.HardwareUpgradeMethodSupportList"]]

)))

== 7.3 How to change the LoRa Frequency Bands/Region? ==

1324

1325

1326

User can follow the introduction for how to [[upgrade image>>||anchor="H7.2HowtoupgradefirmwareforWSC1-L3F"]]. When download the images, choose the required image file for download.

1327

1328

1329

== 7.4 Can I add my weather sensors? ==

1330

1331

1332

Yes, connect the sensor to RS485 bus and see instruction: [[add sensors.>>||anchor="H3.3AddorDeleteRS485Sensor"]]

1333

1334

1335

= 8. Trouble Shooting =

1336

1337

== 8.1 AT Command input doesn't work ==

(((

In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.

)))

= 9. Order Info =

== 9.1 Main Process Unit ==

1348

1349

1350

Part Number: (% style="color:blue" %)**WSC1-L-XX**

1351

1352

(% style="color:blue" %)**XX**(%%): The default frequency band

1353

1354

* (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band

1355

* (% style="color:red" %)**AU915**(%%): LoRaWAN AU915 band

1356

* (% style="color:red" %)**EU433**(%%): LoRaWAN EU433 band

1357

* (% style="color:red" %)**EU868**(%%): LoRaWAN EU868 band

1358

* (% style="color:red" %)**KR920**(%%): LoRaWAN KR920 band

1359

* (% style="color:red" %)**US915**(%%): LoRaWAN US915 band

1360

* (% style="color:red" %)**IN865**(%%): LoRaWAN IN865 band

1361

* (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band

== 9.2 Sensors ==

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:500px" %)

1369

|=(% style="width: 300px;" %)**Sensor Model**|=(% style="width: 200px;" %)**Part Number**

1370

|(% style="width:462px" %)**Rain Gauge**|(% style="width:120px" %)WSS-01

1371

|(% style="width:462px" %)**Rain Gauge installation Bracket for Pole**|(% style="width:120px" %)WS-K2

1372

|(% style="width:462px" %)**Wind Speed Direction 2 in 1 Sensor**|(% style="width:120px" %)WSS-02

1373

|(% style="width:462px" %)**CO2/PM2.5/PM10 3 in 1 Sensor**|(% style="width:120px" %)WSS-03

1374

|(% style="width:462px" %)**Rain/Snow Detect Sensor**|(% style="width:120px" %)WSS-04

1375

|(% style="width:462px" %)**Temperature, Humidity, illuminance and Pressure 4 in 1 sensor**|(% style="width:120px" %)WSS-05

1376

|(% style="width:462px" %)**Total Solar Radiation Sensor**|(% style="width:120px" %)WSS-06

1377

|(% style="width:462px" %)**PAR (Photosynthetically Available Radiation)**|(% style="width:120px" %)WSS-07

= 10. Support =

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

1385

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:file:///D:/市场资料/说明书/LoRa/LT系列/support@dragino.com]].

= 11. Appendix I: Field Installation Photo =

1390

1391

1392

[[image:1656058346362-132.png||height="685" width="732"]]

1393

1394

(% style="color:blue" %)**Storage Battery: 12v,12AH li battery**