Dragino LoRaWAN Weather Station User Manual

Dragino LoRaWAN weather station series products are designed for measuring atmospheric conditions to provide information for weather forecasts and to study the (% style="color:#4472c4" %)**weather and climate**(%%). They consist of a (% style="color:#4472c4" %)**main process device (WSC1-L) and various sensors**.

25

)))

26

27

(((

28

The sensors include various type such as: (% style="color:#4472c4" %)**Rain Gauge**, **Temperature/Humidity/Pressure sensor**, **Wind Speed/direction sensor**, **Illumination sensor**, **CO2 sensor**, **Rain/Snow sensor**,** PM2.5/10 sensor**, **PAR(Photosynthetically Available Radiation) sensor, Total Solar Radiation sensor**(%%) and so on.

)))

(((

Main process device WSC1-L is an outdoor LoRaWAN RS485 end node. It is powered by external (% style="color:#4472c4" %)**12v solar power**(%%) and have a (% style="color:#4472c4" %)**built-in li-on backup battery**(%%). WSC1-L reads value from various sensors and upload these sensor data to IoT server via LoRaWAN wireless protocol.

)))

(((

WSC1-L is full compatible with(% style="color:#4472c4" %)** LoRaWAN Class C protocol**(%%), it can work with standard LoRaWAN gateway.

)))

= 2. How to use =

== 2.1 Installation ==

44

45

Below is an installation example for the weather station. Field installation example can be found at [[Appendix I: Field Installation Photo.>>||anchor="H11.AppendixI:FieldInstallationPhoto"]]

46

47

[[image:1656041948552-849.png]]

48

49

50

(% style="color:blue" %)** Wiring:**

51

52

~1. WSC1-L and sensors all powered by solar power via MPPT

53

54

2. WSC1-L and sensors connect to each other via RS485/Modbus.

55

56

3. WSC1-L read value from each sensor and send uplink via LoRaWAN

57

58

59

WSC1-L is shipped with a RS485 converter board, for the easy connection to different sensors and WSC1-L. Below is a connection photo:

60

61

[[image:1656042136605-251.png]]

62

63

64

(% style="color:red" %)**Notice 1:**

65

66

* All weather sensors and WSC1-L are powered by MPPT solar recharge controller. MPPT is connected to solar panel and storage battery.

67

* WSC1-L has an extra 1000mAh back up battery. So it can work even solar panel and storage battery Fails.

68

* Weather sensors won’t work if solar panel and storage battery fails.

(% style="color:red" %)**Notice 2:**

73

74

Due to shipment and importation limitation, user is better to purchase below parts locally:

* Solar Panel

* Storage Battery

* MPPT Solar Recharger

79

* Mounting Kit includes pole and mast assembly. Each weather sensor has it’s own mounting assembly, user can check the sensor section in this manual.

* Cabinet.

== 2.2 How it works? ==

87

88

(((

89

Each WSC1-L is shipped with a worldwide unique set of OTAA keys. To use WSC1-L in a LoRaWAN network, user needs to input the OTAA keys in LoRaWAN network server. After finish installation as above. Create WSC1-L in your LoRaWAN server and Power on WSC1-L , it can join the LoRaWAN network and start to transmit sensor data. The default period for each uplink is 20 minutes.

)))

(((

Open WSC1-L and put the yellow jumper as below position to power on WSC1-L.

95

)))

96

97

[[image:1656042192857-709.png]]

98

99

100

(% style="color:red" %)**Notice:**

101

102

1. WSC1-L will auto scan available weather sensors when power on or reboot.

103

1. User can send a downlink command to WSC1-L to do a re-scan on the available sensors.

== 2.3 Example to use for LoRaWAN network ==

109

110

This section shows an example for how to join the TTN V3 LoRaWAN IoT server. Usages with other LoRaWAN IoT servers are of similar procedure.

111

112

113

[[image:1656042612899-422.png]]

Assume the DLOS8 is already set to connect to [[TTN V3 network >>url:https://eu1.cloud.thethings.network/]]. We need to add the WSC1-L device in TTN V3:

118

119

120

(% style="color:blue" %)**Step 1**(%%): Create a device in TTN V3 with the OTAA keys from WSC1-L.

121

122

Each WSC1-L is shipped with a sticker with the default device EUI as below:

123

124

[[image:image-20220624115043-1.jpeg]]

125

126

127

User can enter these keys in the LoRaWAN Server portal. Below is TTN V3 screen shot:

128

129

**Add APP EUI in the application.**

130

131

[[image:1656042662694-311.png]]

132

133

[[image:1656042673910-429.png]]

**Choose Manually to add WSC1-L**

139

140

[[image:1656042695755-103.png]]

**Add APP KEY and DEV EUI**

145

146

[[image:1656042723199-746.png]]

(((

(% style="color:blue" %)**Step 2**(%%): Power on WSC1-L, it will start to join TTN server. After join success, it will start to upload sensor data to TTN V3 and user can see in the panel.

)))

[[image:1656042745346-283.png]]

== 2.4 Uplink Payload ==

160

161

Uplink payloads include two types: Valid Sensor Value and other status / control command.

162

163

* Valid Sensor Value: Use FPORT=2

164

* Other control command: Use FPORT other than 2.

=== 2.4.1 Uplink FPORT~=5, Device Status ===

170

171

Uplink the device configures with FPORT=5. Once WSC1-L Joined the network, it will uplink this message to the server. After first uplink, WSC1-L will uplink Device Status every 12 hours

(((

User can also use downlink command(0x2301) to ask WSC1-L to resend this uplink

176

)))

177

178

(% border="1" cellspacing="8" style="background-color:#ffffcc; color:green; width:500px" %)

179

180

|(% style="width:99px" %)**Value**|(% style="width:112px" %)[[Sensor Model>>||anchor="HSensorModel:"]]|(% style="width:135px" %)[[Firmware Version>>||anchor="HFirmwareVersion:"]]|(% style="width:126px" %)[[Frequency Band>>||anchor="HFrequencyBand:"]]|(% style="width:85px" %)[[Sub-band>>||anchor="HSub-Band:"]]|(% style="width:46px" %)[[BAT>>||anchor="HBAT:"]]|(% style="width:166px" %)[[Weather Sensor Types>>||anchor="HWeatherSensorTypes:"]]

181

182

[[image:1656043061044-343.png]]

183

184

185

Example Payload (FPort=5): [[image:image-20220624101005-1.png]]

==== (% style="color:#037691" %)**Sensor Model:**(%%) ====

190

191

For WSC1-L, this value is 0x0D.

==== (% style="color:#037691" %)**Firmware Version:**(%%) ====

196

197

0x0100, Means: v1.0.0 version.

==== (% style="color:#037691" %)**Frequency Band:**(%%) ====

*0x01: EU868

*0x02: US915

*0x03: IN865

*0x04: AU915

*0x05: KZ865

*0x06: RU864

*0x07: AS923

*0x08: AS923-1

*0x09: AS923-2

*0x0a: AS923-3

==== (% style="color:#037691" %)**Sub-Band:**(%%) ====

226

227

value 0x00 ~~ 0x08(only for CN470, AU915,US915. Others are0x00)

==== (% style="color:#037691" %)**BAT:**(%%) ====

232

233

(((

234

shows the battery voltage for WSC1-L MCU.

)))

(((

Ex1: 0x0BD6/1000 = 3.03 V

)))

==== (% style="color:#037691" %)**Weather Sensor Types:**(%%) ====

244

245

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:100px" %)

246

|Byte3|Byte2|Byte1

247

248

Bit = 1 means this sensor is connected, Bit=0 means this sensor is not connected

249

250

[[image:image-20220624134713-1.png]]

251

252

253

Eg: 0x1000FE = 1 0000 0000 0000 1111 1110(b)

254

255

External sensors detected by WSC1-L include :

custom sensor A1,

PAR sensor (WSS-07),

Total Solar Radiation sensor (WSS-06),

262

263

CO2/PM2.5/PM10 (WSS-03),

264

265

Wind Speed/Direction (WSS-02)

266

267

268

User can also use downlink command(0x26 01) to ask WSC1-L to resend this uplink :

269

270

(% style="color:#037691" %)**Downlink:0x26 01**

271

272

[[image:1656049673488-415.png]]

=== 2.4.2 Uplink FPORT~=2, Real time sensor value ===

277

278

(((

279

WSC1-L will send this uplink after Device Config uplink once join LoRaWAN network successfully. And it will periodically send this uplink. Default interval is 20 minutes and [[can be changed>>||anchor="H3.1SetTransmitIntervalTime"]].

)))

(((

Uplink uses FPORT=2 and every 20 minutes send one uplink by default.

)))

(((

The upload length is dynamic, depends on what type of weather sensors are connected. The uplink payload is combined with sensor segments. As below:

)))

(% style="color:#4472c4" %)** Uplink Payload**:

293

294

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:464px" %)

295

|(% style="width:140px" %)Sensor Segment 1|(% style="width:139px" %)Sensor Segment 2|(% style="width:42px" %)……|(% style="width:140px" %)Sensor Segment n

296

297

(% style="color:#4472c4" %)** Sensor Segment Define**:

298

299

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:330px" %)

300

|(% style="width:89px" %)Type Code|(% style="width:114px" %)Length (Bytes)|(% style="width:124px" %)Measured Value

301

302

(% style="color:#4472c4" %)**Sensor Type Table:**

303

304

[[image:image-20220624140352-2.png]]

(((

Below is an example payload: [[image:image-20220624140615-3.png]]

)))

(((

)))

(((

When sending this payload to LoRaWAN server. WSC1-L will send this in one uplink or several uplinks according to LoRaWAN spec requirement. For example, total length of Payload is 54 bytes.

)))

* (((

When WSC1-L sending in US915 frequency DR0 data rate. Because this data rate has limitation of 11 bytes payload for each uplink. The payload will be split into below packets and uplink.

)))

(((

Uplink 1: [[image:image-20220624140735-4.png]]

)))

(((

)))

(((

Uplink 2: [[image:image-20220624140842-5.png]]

)))

(((

)))

* (((

When WSC1-L sending in EU868 frequency DR0 data rate. The payload will be split into below packets and uplink:

)))

(((

Uplink 1: [[image:image-20220624141025-6.png]]

)))

(((

)))

Uplink 2: [[image:image-20220624141100-7.png]]

=== 2.4.3 Decoder in TTN V3 ===

357

358

In LoRaWAN platform, user only see HEX payload by default, user needs to use payload formatters to decode the payload to see human-readable value.

359

360

361

Download decoder for suitable platform from:

362

363

[[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Weather_Station/WSC1-L/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Weather_Station/WSC1-L/]]

and put as below:

[[image:1656051152438-578.png]]

== 2.5 Show data on Application Server ==

372

373

Application platform provides a human friendly interface to show the sensor data, once we have sensor data in TTN V3, we can use Datacake to connect to TTN V3 and see the data in Datacake. Below are the steps:

374

375

376

(% style="color:blue" %)**Step 1**(%%): Be sure that your device is programmed and properly connected to the LoRaWAN network.

377

378

(% style="color:blue" %)**Step 2**(%%): Configure your Application to forward data to Datacake you will need to add integration. Go to TTN V3 Console ~-~-> Applications ~-~-> Integrations ~-~-> Add Integrations.

379

380

[[image:1656051197172-131.png]]

**Add TagoIO:**

[[image:1656051223585-631.png]]

**Authorization:**

[[image:1656051248318-368.png]]

391

392

393

In TagoIO console ([[https:~~/~~/admin.tago.io~~/~~/>>url:https://datacake.co/]]) , add WSC1-L:

394

395

[[image:1656051277767-168.png]]

= 3. Configure WSC1-L via AT Command or LoRaWAN Downlink =

400

401

Use can configure WSC1-L via AT Command or LoRaWAN Downlink.

402

403

* AT Command Connection: See [[FAQ>>||anchor="H7.FAQ"]].

404

* LoRaWAN Downlink instruction for different platforms: [[Use Note for Server>>doc:Main.WebHome]](IoT LoRaWAN Server)

405

406

There are two kinds of commands to configure WSC1-L, they are:

407

408

* (% style="color:#4472c4" %)**General Commands**.

409

410

These commands are to configure:

411

412

* General system settings like: uplink interval.

413

* LoRaWAN protocol & radio related command.

414

415

They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack((% style="color:red" %)Note~*~*)(%%). These commands can be found on the wiki: [[End Device Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]

416

417

(% style="color:red" %)Note~*~*: Please check early user manual if you don’t have v1.8.0 firmware.

418

419

420

* (% style="color:#4472c4" %)**Commands special design for WSC1-L**

421

422

These commands only valid for WSC1-L, as below:

== 3.1 Set Transmit Interval Time ==

430

431

Feature: Change LoRaWAN End Node Transmit Interval.

432

433

(% style="color:#037691" %)**AT Command: AT+TDC**

434

435

[[image:image-20220624142619-8.png]]

436

437

438

(% style="color:#037691" %)**Downlink Command: 0x01**

439

440

Format: Command Code (0x01) followed by 3 bytes time value.

441

442

If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.

443

444

* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds

445

* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds

== 3.2 Set Emergency Mode ==

451

452

Feature: In emergency mode, WSC1-L will uplink data every 1 minute.

453

454

(% style="color:#037691" %)**AT Command:**

455

456

[[image:image-20220624142956-9.png]]

457

458

459

(% style="color:#037691" %)**Downlink Command:**

460

461

* 0xE101 Same as: AT+ALARMMOD=1

462

* 0xE100 Same as: AT+ALARMMOD=0

== 3.3 Add or Delete RS485 Sensor ==

468

469

Feature: User can add or delete 3^^rd^^ party sensor as long they are RS485/Modbus interface,baud rate support 9600.Maximum can add 4 sensors.

470

471

(% style="color:#037691" %)**AT Command: **

472

473

(% style="color:blue" %)**AT+DYSENSOR=Type_Code, Query_Length, Query_Command , Read_Length , Valid_Data ,has_CRC,timeout**

474

475

* Type_Code range: A1 ~~ A4

476

* Query_Length: RS485 Query frame length, Value cannot be greater than 10

477

* Query_Command: RS485 Query frame data to be sent to sensor, cannot be larger than 10 bytes

478

* Read_Length: RS485 response frame length supposed to receive. Max can receive

479

* Valid_Data: valid data from RS485 Response, Valid Data will be added to Payload and upload via LoRaWAN.

480

* has_CRC: RS485 Response crc check (0: no verification required 1: verification required). If CRC=1 and CRC error, valid data will be set to 0.

481

* timeout: RS485 receive timeout (uint:ms). Device will close receive window after timeout

**Example:**

User need to change external sensor use the type code as address code.

486

487

With a 485 sensor, after correctly changing the address code to A1, the RS485 query frame is shown in the following table:

488

489

[[image:image-20220624143553-10.png]]

490

491

492

The response frame of the sensor is as follows:

493

494

[[image:image-20220624143618-11.png]]

**Then the following parameters should be:**

499

500

* Address_Code range: A1

501

* Query_Length: 8

502

* Query_Command: A103000000019CAA

503

* Read_Length: 8

504

* Valid_Data: 24 (Indicates that the data length is 2 bytes, starting from the 4th byte)

505

* has_CRC: 1

506

* timeout: 1500 (Fill in the test according to the actual situation)

507

508

**So the input command is:**

509

510

AT+DYSENSOR=A1,8,A103000000019CAA,8,24,1,1500

511

512

513

In every sampling. WSC1-L will auto append the sensor segment as per this structure and uplink.

514

515

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:351px" %)

516

|=(% style="width: 94px;" %)Type Code|=(% style="width: 121px;" %)Length (Bytes)|=(% style="width: 132px;" %)Measured Value

517

|(% style="width:94px" %)A1|(% style="width:121px" %)2|(% style="width:132px" %)0x000A

518

519

**Related commands:**

520

521

AT+DYSENSOR=A1,0 ~-~-> Delete 3^^rd^^ party sensor A1.

522

523

AT+DYSENSOR ~-~-> List All 3^^rd^^ Party Sensor. Like below:

524

525

526

(% style="color:#037691" %)**Downlink Command: **

527

528

**delete custom sensor A1:**

529

530

* 0xE5A1 Same as: AT+DYSENSOR=A1,0

531

532

**Remove all custom sensors**

* 0xE5FF

== 3.4 RS485 Test Command ==

540

541

(% style="color:#037691" %)**AT Command:**

542

543

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:474px" %)

544

|=(% style="width: 159px;" %)**Command Example**|=(% style="width: 227px;" %)**Function**|=(% style="width: 85px;" %)**Response**

545

|(% style="width:159px" %)AT+RSWRITE=xxxxxx|(% style="width:227px" %)(((

546

Send command to 485 sensor

547

548

Range : no more than 10 bytes

549

)))|(% style="width:85px" %)OK

550

551

Eg: Send command **01 03 00 00 00 01 84 0A** to 485 sensor

552

553

AT+RSWRITE=0103000001840A

554

555

556

(% style="color:#037691" %)**Downlink Command:**

557

558

* 0xE20103000001840A Same as: AT+RSWRITE=0103000001840A

== 3.5 RS485 response timeout ==

564

565

Feature: Set or get extended time to receive 485 sensor data.

566

567

(% style="color:#037691" %)**AT Command:**

568

569

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:433px" %)

570

|=(% style="width: 157px;" %)**Command Example**|=(% style="width: 188px;" %)**Function**|=(% style="width: 85px;" %)**Response**

571

|(% style="width:157px" %)AT+DTR=1000|(% style="width:188px" %)(((

572

Set response timeout to:

573

574

Range : 0~~10000

575

)))|(% style="width:85px" %)OK

576

577

(% style="color:#037691" %)**Downlink Command:**

578

579

Format: Command Code (0xE0) followed by 3 bytes time value.

580

581

If the downlink payload=E0000005, it means set the END Node’s Transmit Interval to 0x000005=5(S), while type code is E0.

582

583

* Example 1: Downlink Payload: E0000005 ~/~/ Set Transmit Interval (DTR) = 5 seconds

584

* Example 2: Downlink Payload: E000000A ~/~/ Set Transmit Interval (DTR) = 10 seconds

== 3.6 Set Sensor Type ==

590

591

(((

592

Feature: Set sensor in used. If there are 6 sensors, user can set to only send 5 sensors values.

)))

(((

See [[definition>>||anchor="HWeatherSensorTypes:"]] for the sensor type.

597

)))

598

599

[[image:image-20220624144904-12.png]]

600

601

602

(% style="color:#037691" %)**AT Command:**

603

604

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:377px" %)

605

|=(% style="width: 157px;" %)**Command Example**|=(% style="width: 130px;" %)**Function**|=(% style="width: 87px;" %)**Response**

606

|(% style="width:157px" %)AT+STYPE=80221|(% style="width:130px" %)Set sensor types|(% style="width:87px" %)OK

607

608

Eg: The setting command **AT+STYPE=802212** means:

609

610

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:495px" %)

So wsc1-L will upload the following data: Custom Sensor A1, Rain Gauge,CO2,BAT.

619

620

621

(% style="color:#037691" %)**Downlink Command:**

622

623

* 0xE400802212 Same as: AT+STYPE=80221

624

625

(% style="color:red" %)**Note:**

626

627

~1. The sensor type will not be saved to flash, and the value will be updated every time the sensor is restarted or rescanned.

= 4. Power consumption and battery =

633

634

== 4.1 Total Power Consumption ==

635

636

Dragino Weather Station serial products include the main process unit ( WSC1-L ) and various sensors. The total power consumption equal total power of all above units. The power consumption for main process unit WSC1-L is 18ma @ 12v. and the power consumption of each sensor can be found on the Sensors chapter.

637

638

639

== 4.2 Reduce power consumption ==

640

641

The main process unit WSC1-L is set to LoRaWAN Class C by default. If user want to reduce the power consumption of this unit, user can set it to run in Class A. In Class A mode, WSC1-L will not be to get real-time downlink command from IoT Server.

== 4.3 Battery ==

(((

All sensors are only power by external power source. If external power source is off. All sensor won't work.

)))

(((

Main Process Unit WSC1-L is powered by both external power source and internal 1000mAh rechargeable battery. If external power source is off, WSC1-L still runs and can send periodically uplinks, but the sensors value will become invalid. External power source can recharge the 1000mAh rechargeable battery.

)))

= 5. Main Process Unit WSC1-L =

== 5.1 Features ==

* Wall Attachable.

* LoRaWAN v1.0.3 Class A protocol.

661

* RS485 / Modbus protocol

662

* Frequency Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915

663

* AT Commands to change parameters

664

* Remote configure parameters via LoRaWAN Downlink

665

* Firmware upgradable via program port

666

* Powered by external 12v battery

667

* Back up rechargeable 1000mAh battery

668

* IP Rating: IP65

669

* Support default sensors or 3rd party RS485 sensors

== 5.2 Power Consumption ==

675

676

WSC1-L (without external sensor): Idle: 4mA, Transmit: max 40mA

677

678

679

== 5.3 Storage & Operation Temperature ==

-20°C to +60°C

== 5.4 Pin Mapping ==

685

686

[[image:1656054149793-239.png]]

== 5.5 Mechanical ==

Refer LSn50v2 enclosure drawing in: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=LSN50-LoRaST/Mechanical_Drawing/>>url:https://www.dragino.com/downloads/index.php?dir=LSN50-LoRaST/Mechanical_Drawing/]]

692

693

694

== 5.6 Connect to RS485 Sensors ==

695

696

WSC1-L includes a RS485 converter PCB. Which help it easy to connect multiply RS485 sensors. Below is the photo for reference.

697

698

699

[[image:1656054389031-379.png]]

700

701

702

Hardware Design for the Converter Board please see:

703

704

[[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Weather_Station/RS485_Converter_Board/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Weather_Station/RS485_Converter_Board/]]

705

706

707

= 6. Weather Sensors =

708

709

== 6.1 Rain Gauge ~-~- WSS-01 ==

(((

WSS-01 RS485 Rain Gauge is used in meteorology and hydrology to gather and measure the amount of liquid precipitation (mainly rainfall) over an area.

)))

(((

WSS-01 uses a tipping bucket to detect rainfall. The tipping bucket use 3D streamline shape to make sure it works smoothly and is easy to clean.

)))

(((

WSS-01 is designed to support the Dragino Weather station solution. Users only need to connect WSS-01 RS485 interface to WSC1-L. The weather station main processor WSC1-L can detect and upload the rainfall to the IoT Server via wireless LoRaWAN protocol

)))

(((

The tipping bucket of WSS-01 is adjusted to the best angle. When installation, user only needs to screw up and adjust the bottom horizontally.

)))

(((

WSS-01 package includes screw which can be installed to ground. If user want to install WSS-01 on pole, they can purchase WS-K2 bracket kit.

)))

=== 6.1.1 Feature ===

734

735

* RS485 Rain Gauge

736

* Small dimension, easy to install

737

* Vents under funnel, avoid leaf or other things to avoid rain flow.

738

* ABS enclosure.

739

* Horizontal adjustable.

=== 6.1.2 Specification ===

* Resolution: 0.2mm

* Accuracy: ±3%

* Rainfall strength: 0mm～4mm/min (max 8mm/min)

749

* Input Power: DC 5~~24v

750

* Interface: RS485

751

* Working Temperature: 0℃～70℃ ( incorrect below 0 degree, because water become ICE)

752

* Working Humidity: <100% (no dewing)

753

* Power Consumption: 4mA @ 12v.

=== 6.1.3 Dimension ===

759

760

[[image:1656054957406-980.png]]

761

762

763

=== 6.1.4 Pin Mapping ===

764

765

[[image:1656054972828-692.png]]

766

767

768

=== 6.1.5 Installation Notice ===

769

770

Do not power on while connect the cables. Double check the wiring before power on.

771

772

Installation Photo as reference:

773

774

775

(% style="color:#4472c4" %)** Install on Ground:**

776

777

WSS-01 Rain Gauge include screws so can install in ground directly .

778

779

780

(% style="color:#4472c4" %)** Install on pole:**

781

782

If user want to install on pole, they can purchase the (% style="color:#4472c4" %)** WS-K2 : Bracket Kit for Pole installation**(%%), and install as below:

783

784

[[image:image-20220624152218-1.png||height="526" width="276"]]

785

786

WS-K2: Bracket Kit for Pole installation

787

788

789

WSSC-K2 dimension document, please see:

790

791

[[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Weather_Station/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Weather_Station/]]

792

793

794

== 6.2 Wind Speed/Direction ~-~- WSS-02 ==

795

796

[[image:1656055444035-179.png]]

797

798

(((

799

WSS-02 is a RS485 wind speed and wind direction monitor designed for weather station solution.

)))

(((

WSS-02 shell is made of polycarbonate composite material, which has good anti-corrosion and anti-corrosion characteristics, and ensure the long-term use of the sensor without rust. At the same time, it cooperates with the internal smooth bearing system to ensure the stability of information collection

)))

(((

Users only need to connect WSS-02 RS485 interface to WSC1-L. The weather station main processor WSC1-L can detect and upload the wind speed and direction to the IoT Server via wireless LoRaWAN protocol.

)))

=== 6.2.1 Feature ===

812

813

* RS485 wind speed / direction sensor

814

* PC enclosure, resist corrosion

=== 6.2.2 Specification ===

820

821

* Wind speed range: 0 ~~ 30m/s, (always show 30m/s for higher speed)

822

* Wind direction range: 0 ~~ 360°

823

* Start wind speed: ≤0.3m/s

824

* Accuracy: ±（0.3＋0.03V）m/s , ±1°

825

* Input Power: DC 5~~24v

826

* Interface: RS485

827

* Working Temperature: -30℃～70℃

828

* Working Humidity: <100% (no dewing)

829

* Power Consumption: 13mA ~~ 12v.

830

* Cable Length: 2 meters

=== 6.2.3 Dimension ===

836

837

[[image:image-20220624152813-2.png]]

838

839

840

=== 6.2.4 Pin Mapping ===

841

842

[[image:1656056281231-994.png]]

843

844

845

=== 6.2.5 Angle Mapping ===

846

847

[[image:1656056303845-585.png]]

848

849

850

=== 6.2.6 Installation Notice ===

851

852

Do not power on while connect the cables. Double check the wiring before power on.

853

854

The sensor must be installed with below direction, towards North.

855

856

[[image:image-20220624153901-3.png]]

857

858

859

== 6.3 CO2/PM2.5/PM10 ~-~- WSS-03 ==

(((

WSS-03 is a RS485 Air Quality sensor. It can monitor CO2, PM2.5 and PM10 at the same time.

)))

(((

WSS-03 uses weather proof shield which can make sure the sensors are well protected against UV & radiation.

)))

(((

WSS-03 is designed to support the Dragino Weather station solution. Users only need to connect WSS-03 RS485 interface to WSC1-L. The weather station main processor WSC1-L can detect and upload the environment CO2, PM2.5 and PM10 to the IoT Server via wireless LoRaWAN protocol.

)))

=== 6.3.1 Feature ===

876

877

* RS485 CO2, PM2.5, PM10 sensor

878

* NDIR to measure CO2 with Internal Temperature Compensation

879

* Laser Beam Scattering to PM2.5 and PM10

=== 6.3.2 Specification ===

885

886

* CO2 Range: 0～5000ppm, accuracy: ±3%F•S（25℃）

887

* CO2 resolution: 1ppm

888

* PM2.5/PM10 Range: 0～1000μg/m3 , accuracy ±3%F•S（25℃）

889

* PM2.5/PM10 resolution: 1μg/m3

890

* Input Power: DC 7 ~~ 24v

891

* Preheat time: 3min

892

* Interface: RS485

893

* Working Temperature:

894

** CO2: 0℃～50℃;

895

** PM2.5/PM10: -30 ~~ 50℃

896

* Working Humidity:

897

** PM2.5/PM10: 15～80%RH (no dewing)

898

** CO2: 0～95%RH

899

* Power Consumption: 50mA@ 12v.

=== 6.3.3 Dimension ===

905

906

[[image:1656056708366-230.png]]

907

908

909

=== 6.3.4 Pin Mapping ===

910

911

[[image:1656056722648-743.png]]

912

913

914

=== 6.3.5 Installation Notice ===

915

916

Do not power on while connect the cables. Double check the wiring before power on.

917

918

[[image:1656057016033-551.png]]

919

920

[[image:1656056751153-304.png]]

921

922

[[image:1656056766224-773.png]]

923

924

925

== 6.4 Rain/Snow Detect ~-~- WSS-04 ==

(((

WSS-04 is a RS485 rain / snow detect sensor. It can monitor Rain or Snow event.

)))

(((

WSS-04 has auto heating feature, this ensures measurement more reliable.

)))

(((

WSS-04 is designed to support the Dragino Weather station solution. Users only need to connect WSS-04 RS485 interface to WSC1-L. The weather station main processor WSC1-L can detect and upload the SNOW/Rain Event to the IoT Server via wireless LoRaWAN protocol.

)))

=== 6.4.1 Feature ===

943

944

* RS485 Rain/Snow detect sensor

945

* Surface heating to dry

946

* grid electrode uses Electroless Nickel/Immersion Gold design for resist corrosion

=== 6.4.2 Specification ===

952

953

* Detect if there is rain or snow

954

* Input Power: DC 12 ~~ 24v

955

* Interface: RS485

956

* Working Temperature: -30℃～70℃

957

* Working Humidity: 10～90%RH

958

* Power Consumption:

959

** No heating: 12mA @ 12v,

960

** heating: 94ma @ 12v.

=== 6.4.3 Dimension ===

966

967

[[image:1656056844782-155.png]]

968

969

970

=== 6.4.4 Pin Mapping ===

971

972

[[image:1656056855590-754.png]]

973

974

975

=== 6.4.5 Installation Notice ===

976

977

Do not power on while connect the cables. Double check the wiring before power on.

978

979

980

Install with 15°degree.

981

982

[[image:1656056873783-780.png]]

983

984

985

[[image:1656056883736-804.png]]

986

987

988

=== 6.4.6 Heating ===

989

990

(((

991

WSS-04 supports auto-heat feature. When the temperature is below the heat start temperature 15℃, WSS-04 starts to heat and stop at stop temperature (default is 25℃).

)))

== 6.5 Temperature, Humidity, Illuminance, Pressure ~-~- WSS-05 ==

(((

WSS-05 is a 4 in 1 RS485 sensor which can monitor Temperature, Humidity, Illuminance and Pressure at the same time.

)))

(((

WSS-05 is designed to support the Dragino Weather station solution. Users only need to connect WSS-05 RS485 interface to WSC1-L. The weather station main processor WSC1-L can detect and upload environment Temperature, Humidity, Illuminance, Pressure to the IoT Server via wireless LoRaWAN protocol.

)))

=== 6.5.1 Feature ===

1008

1009

* RS485 Temperature, Humidity, Illuminance, Pressure sensor

=== 6.5.2 Specification ===

1015

1016

* Input Power: DC 12 ~~ 24v

1017

* Interface: RS485

1018

* Temperature Sensor Spec:

** Range: -30 ~~ 70℃

** resolution 0.1℃

** Accuracy: ±0.5℃

* Humidity Sensor Spec:

1023

** Range: 0 ~~ 100% RH

1024

** resolution 0.1 %RH

1025

** Accuracy: 3% RH

1026

* Pressure Sensor Spec:

1027

** Range: 10～1100hPa

1028

** Resolution: 0.1hPa

1029

** Accuracy: ±0.1hPa

1030

* Illuminate sensor:

1031

** Range: 0～2/20/200kLux

1032

** Resolution: 10 Lux

1033

** Accuracy: ±3％FS

1034

* Working Temperature: -30℃～70℃

1035

* Working Humidity: 10～90%RH

1036

* Power Consumption: 4mA @ 12v

=== 6.5.3 Dimension ===

1042

1043

[[image:1656057170639-522.png]]

1044

1045

1046

=== 6.5.4 Pin Mapping ===

1047

1048

[[image:1656057181899-910.png]]

1049

1050

1051

=== 6.5.5 Installation Notice ===

1052

1053

Do not power on while connect the cables. Double check the wiring before power on.

1054

1055

[[image:1656057199955-514.png]]

1056

1057

1058

[[image:1656057212438-475.png]]

1059

1060

1061

== 6.6 Total Solar Radiation sensor ~-~- WSS-06 ==

(((

WSS-06 is Total Radiation Sensor can be used to measure the total solar radiation in the spectral range of 0.3 to 3 μm (300 to 3000 nm). If the sensor face is down, the reflected radiation can be measured, and the shading ring can also be used to measure the scattered radiation.

)))

(((

The core device of the radiation sensor is a high-precision photosensitive element, which has good stability and high precision; at the same time, a precision-machined PTTE radiation cover is installed outside the sensing element, which effectively prevents environmental factors from affecting its performance

)))

(((

WSS-06 is designed to support the Dragino Weather station solution. Users only need to connect WSS-06 RS485 interface to WSC1-L. The weather station main processor WSC1-L can detect and upload Total Solar Radiation to the IoT Server via wireless LoRaWAN protocol.

)))

=== 6.6.1 Feature ===

1079

1080

* RS485 Total Solar Radiation sensor

1081

* Measure Total Radiation between 0.3～3μm（300～3000nm）

1082

* Measure Reflected Radiation if sense area towards ground.

=== 6.6.2 Specification ===

1088

1089

* Input Power: DC 5 ~~ 24v

1090

* Interface: RS485

1091

* Detect spectrum: 0.3～3μm（300～3000nm）

1092

* Measure strength range: 0～2000W/m2

1093

* Resolution: 0.1W/m2

1094

* Accuracy: ±3%

1095

* Yearly Stability: ≤±2％

1096

* Cosine response: ≤7％ (@ Sun angle 10°)

1097

* Temperature Effect: ±2％（－10℃～40℃）

1098

* Working Temperature: -40℃～70℃

1099

* Working Humidity: 10～90%RH

1100

* Power Consumption: 4mA @ 12v

=== 6.6.3 Dimension ===

1106

1107

[[image:1656057348695-898.png]]

1108

1109

1110

=== 6.6.4 Pin Mapping ===

1111

1112

[[image:1656057359343-744.png]]

1113

1114

1115

=== 6.6.5 Installation Notice ===

1116

1117

Do not power on while connect the cables. Double check the wiring before power on.

1118

1119

[[image:1656057369259-804.png]]

1120

1121

1122

[[image:1656057377943-564.png]]

1123

1124

1125

== 6.7 PAR (Photosynthetically Available Radiation) ~-~- WSS-07 ==

(((

WSS-07 photosynthetically active radiation sensor is mainly used to measure the photosynthetically active radiation of natural light in the wavelength range of 400-700nm.

)))

(((

WSS-07 use precision optical detectors and has an optical filter of 400-700nm, when natural light is irradiated, a voltage signal proportional to the intensity of the incident radiation is generated, and its luminous flux density is proportional to the cosine of the direct angle of the incident light.

)))

(((

WSS-07 is designed to support the Dragino Weather station solution. Users only need to connect WSS-07 RS485 interface to WSC1-L. The weather station main processor WSC1-L can detect and upload Photosynthetically Available Radiation to the IoT Server via wireless LoRaWAN protocol.

)))

=== 6.7.1 Feature ===

1142

1143

PAR (Photosynthetically Available Radiation) sensor measure 400 ~~ 700nm wavelength nature light's Photosynthetically Available Radiation.

1144

1145

When nature light shine on the sense area, it will generate a signal base on the incidence radiation strength.

1146

1147

1148

=== 6.7.2 Specification ===

1149

1150

* Input Power: DC 5 ~~ 24v

1151

* Interface: RS485

1152

* Response Spectrum: 400～700nm

1153

* Measure range: 0～2500μmol/m2•s

1154

* Resolution: 1μmol/m2•s

1155

* Accuracy: ±2%

1156

* Yearly Stability: ≤±2％

1157

* Working Temperature: -30℃～75℃

1158

* Working Humidity: 10～90%RH

1159

* Power Consumption: 3mA @ 12v

=== 6.7.3 Dimension ===

1165

1166

[[image:1656057538793-888.png]]

1167

1168

1169

=== 6.7.4 Pin Mapping ===

1170

1171

[[image:1656057548116-203.png]]

1172

1173

1174

=== 6.7.5 Installation Notice ===

1175

1176

Do not power on while connect the cables. Double check the wiring before power on.

1177

1178

1179

[[image:1656057557191-895.png]]

1180

1181

1182

[[image:1656057565783-251.png]]

= 7. FAQ =

== 7.1 What else do I need to purchase to build Weather Station? ==

1188

1189

Below is the installation photo and structure:

1190

1191

[[image:1656057598349-319.png]]

1192

1193

1194

[[image:1656057608049-693.png]]

== 7.2 How to upgrade firmware for WSC1-L? ==

1199

1200

(((

1201

Firmware Location & Change log:

)))

(((

[[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/WSC1-L/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/WSC1-L/]]

)))

(((

Firmware Upgrade instruction: [[Firmware Upgrade Instruction>>doc:Main.Firmware Upgrade Instruction for STM32 base products.WebHome||anchor="H2.HardwareUpgradeMethodSupportList"]]

)))

== 7.3 How to change the LoRa Frequency Bands/Region? ==

1215

1216

User can follow the introduction for how to [[upgrade image>>||anchor="H7.2HowtoupgradefirmwareforWSC1-L3F"]]. When download the images, choose the required image file for download.

1217

1218

1219

== 7.4 Can I add my weather sensors? ==

1220

1221

Yes, connect the sensor to RS485 bus and see instruction: [[add sensors.>>||anchor="H3.3AddorDeleteRS485Sensor"]]

1222

1223

1224

= 8. Trouble Shooting =

1225

1226

== 8.1 AT Command input doesn't work ==

1227

1228

(((

1229

In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.

)))

= 9. Order Info =

== 9.1 Main Process Unit ==

1236

1237

Part Number: (% style="color:blue" %)**WSC1-L-XX**

1238

1239

(% style="color:blue" %)**XX**(%%): The default frequency band

1240

1241

* (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band

1242

* (% style="color:red" %)**AU915**(%%): LoRaWAN AU915 band

1243

* (% style="color:red" %)**EU433**(%%): LoRaWAN EU433 band

1244

* (% style="color:red" %)**EU868**(%%): LoRaWAN EU868 band

1245

* (% style="color:red" %)**KR920**(%%): LoRaWAN KR920 band

1246

* (% style="color:red" %)**US915**(%%): LoRaWAN US915 band

1247

* (% style="color:red" %)**IN865**(%%): LoRaWAN IN865 band

1248

* (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band

== 9.2 Sensors ==

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:510px" %)

1253

|=(% style="width: 462px;" %)**Sensor Model**|=(% style="width: 110px;" %)**Part Number**

1254

|(% style="width:462px" %)**Rain Gauge**|(% style="width:110px" %)WSS-01

1255

|(% style="width:462px" %)**Rain Gauge installation Bracket for Pole**|(% style="width:110px" %)WS-K2

1256

|(% style="width:462px" %)**Wind Speed Direction 2 in 1 Sensor**|(% style="width:110px" %)WSS-02

1257

|(% style="width:462px" %)**CO2/PM2.5/PM10 3 in 1 Sensor**|(% style="width:110px" %)WSS-03

1258

|(% style="width:462px" %)**Rain/Snow Detect Sensor**|(% style="width:110px" %)WSS-04

1259

|(% style="width:462px" %)**Temperature, Humidity, illuminance and Pressure 4 in 1 sensor**|(% style="width:110px" %)WSS-05

1260

|(% style="width:462px" %)**Total Solar Radiation Sensor**|(% style="width:110px" %)WSS-06

1261

|(% style="width:462px" %)**PAR (Photosynthetically Available Radiation)**|(% style="width:110px" %)WSS-07

= 10. Support =

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

1267

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:file:///D:/市场资料/说明书/LoRa/LT系列/support@dragino.com]]

1268

1269

1270

= 11. Appendix I: Field Installation Photo =

1271

1272

1273

[[image:1656058346362-132.png]]

1274

1275

**Storage Battery**: 12v,12AH li battery

1276