Changes for page WSC1-L-Dragino LoRaWAN Weather Station User Manual

Last modified by Xiaoling on 2025/04/25 09:08

From version < 82.6 >

edited by Xiaoling
on 2022/06/24 18:02

To version < 79.24 >

edited by Xiaoling
on 2022/06/24 17:24

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -79,8 +79,6 @@
--
--
  == 2.2  How it works? ==
  (((
@@ -101,9 +101,6 @@
 . User can send a downlink command to WSC1-L to do a re-scan on the available sensors.
--
--
--
  == 2.3  Example to use for LoRaWAN network ==
  This section shows an example for how to join the TTN V3 LoRaWAN IoT server. Usages with other LoRaWAN IoT servers are of similar procedure.
@@ -163,9 +163,6 @@
  * Other control command: Use FPORT other than 2.
--
--
--
  === 2.4.1  Uplink FPORT~=5, Device Status ===
  Uplink the device configures with FPORT=5. Once WSC1-L Joined the network, it will uplink this message to the server. After first uplink, WSC1-L will uplink Device Status every 12 hours
@@ -443,6 +443,9 @@
++
++
++
  == 3.1  Set Transmit Interval Time ==
  Feature: Change LoRaWAN End Node Transmit Interval.
@@ -462,9 +462,6 @@
  * Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
--
--
--
  == 3.2  Set Emergency Mode ==
  Feature: In emergency mode, WSC1-L will uplink data every 1 minute.
@@ -480,56 +480,27 @@
  * 0xE100     Same as: AT+ALARMMOD=0
--
--
--
  == 3.3  Add or Delete RS485 Sensor ==
--(((
  Feature: User can add or delete 3^^rd^^ party sensor as long they are RS485/Modbus interface,baud rate support 9600.Maximum can add 4 sensors.
--)))
--(((
  (% style="color:#037691" %)**AT Command: **
--)))
--(((
  (% style="color:blue" %)**AT+DYSENSOR=Type_Code, Query_Length, Query_Command , Read_Length , Valid_Data ,has_CRC,timeout**
--)))
--* (((
--Type_Code range:   A1 ~~ A4
--)))
--* (((
--Query_Length:        RS485 Query frame length, Value cannot be greater than 10
--)))
--* (((
--Query_Command:  RS485 Query frame data to be sent to sensor, cannot be larger than 10 bytes
--)))
--* (((
--Read_Length:   RS485 response frame length supposed to receive. Max can receive
--)))
--* (((
--Valid_Data:       valid data from RS485 Response, Valid Data will be added to Payload and upload via LoRaWAN.
--)))
--* (((
--has_CRC:          RS485 Response crc check  (0: no verification required 1: verification required). If CRC=1 and CRC error, valid data will be set to 0.
--)))
--* (((
--timeout:           RS485 receive timeout (uint:ms). Device will close receive window after timeout
--)))
++* Type_Code range:   A1 ~~ A4
++* Query_Length:        RS485 Query frame length, Value cannot be greater than 10
++* Query_Command:  RS485 Query frame data to be sent to sensor, cannot be larger than 10 bytes
++* Read_Length:   RS485 response frame length supposed to receive. Max can receive
++* Valid_Data:       valid data from RS485 Response, Valid Data will be added to Payload and upload via LoRaWAN.
++* has_CRC:          RS485 Response crc check  (0: no verification required 1: verification required). If CRC=1 and CRC error, valid data will be set to 0.
++* timeout:           RS485 receive timeout (uint:ms). Device will close receive window after timeout
--(((
  **Example:**
--)))
--(((
  User need to change external sensor use the type code as address code.
--)))
--(((
  With a 485 sensor, after correctly changing the address code to A1, the RS485 query frame is shown in the following table:
--)))
  [[image:image-20220624143553-10.png]]
@@ -579,9 +579,6 @@
  * 0xE5FF
--
--
--
  == 3.4  RS485 Test Command ==
  (% style="color:#037691" %)**AT Command:**
@@ -604,9 +604,6 @@
  * 0xE20103000001840A     Same as: AT+RSWRITE=0103000001840A
--
--
--
  == 3.5  RS485 response timeout ==
  Feature: Set or get extended time to receive 485 sensor data.
@@ -631,9 +631,6 @@
  * Example 2: Downlink Payload: E000000A ~/~/ Set Transmit Interval (DTR) = 10 seconds
--
--
--
  == 3.6  Set Sensor Type ==
  (((
@@ -716,6 +716,7 @@
  * IP Rating: IP65
  * Support default sensors or 3rd party RS485 sensors
++
  == 5.2  Power Consumption ==
  WSC1-L (without external sensor): Idle: 4mA, Transmit: max 40mA
@@ -783,6 +783,7 @@
  * ABS enclosure.
  * Horizontal adjustable.
++
  === 6.1.2  Specification ===
  * Resolution: 0.2mm
@@ -794,6 +794,7 @@
  * Working Humidity: <100% (no dewing)
  * Power Consumption: 4mA @ 12v.
++
  === 6.1.3  Dimension ===
   [[image:1656054957406-980.png]]
@@ -864,6 +864,7 @@
  * RS485 wind speed / direction sensor
  * PC enclosure, resist corrosion
++
  === 6.2.2  Specification ===
  * Wind speed range: 0 ~~ 30m/s, (always show 30m/s for higher speed)
@@ -877,6 +877,7 @@
  * Power Consumption: 13mA ~~ 12v.
  * Cable Length: 2 meters
++
  === 6.2.3  Dimension ===
  [[image:image-20220624152813-2.png]]
@@ -927,6 +927,7 @@
  * NDIR to measure CO2 with Internal Temperature Compensation
  * Laser Beam Scattering to PM2.5 and PM10
++
  === 6.3.2  Specification ===
  * CO2 Range: 0～5000ppm, accuracy: ±3%F•S（25℃）
@@ -944,6 +944,7 @@
  ** CO2: 0～95%RH
  * Power Consumption: 50mA@ 12v.
++
  === 6.3.3  Dimension ===
  [[image:1656056708366-230.png]]
@@ -986,6 +986,7 @@
  * Surface heating to dry
  * grid electrode uses Electroless Nickel/Immersion Gold design for resist corrosion
++
  === 6.4.2  Specification ===
  * Detect if there is rain or snow
@@ -997,6 +997,7 @@
  ** No heating: 12mA @ 12v,
  ** heating: 94ma @ 12v.
++
  === 6.4.3  Dimension ===
  [[image:1656056844782-155.png]]
@@ -1046,9 +1046,6 @@
  * RS485 Temperature, Humidity, Illuminance, Pressure sensor
--
--
--
  === 6.5.2  Specification ===
  * Input Power: DC 12 ~~ 24v
@@ -1074,9 +1074,6 @@
  * Power Consumption: 4mA @ 12v
--
--
--
  === 6.5.3  Dimension ===
  [[image:1656057170639-522.png]]
@@ -1121,8 +1121,6 @@
  * Measure Reflected Radiation if sense area towards ground.
--
--
  === 6.6.2  Specification ===
  * Input Power: DC 5 ~~ 24v
@@ -1139,9 +1139,6 @@
  * Power Consumption: 4mA @ 12v
--
--
--
  === 6.6.3  Dimension ===
  [[image:1656057348695-898.png]]
@@ -1203,9 +1203,6 @@
  * Power Consumption: 3mA @ 12v
--
--
--
  === 6.7.3  Dimension ===
  [[image:1656057538793-888.png]]
@@ -1293,6 +1293,9 @@
  * (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
++
++
++
  == 9.2  Sensors ==
  (% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:400px" %)
@@ -1307,6 +1307,9 @@
  |(% style="width:462px" %)**PAR (Photosynthetically Available Radiation)**|(% style="width:110px" %)WSS-07
++
++
++
  = 10.  Support =
  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
@@ -1313,6 +1313,9 @@
  * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:file:///D:/市场资料/说明书/LoRa/LT系列/support@dragino.com]]
++
++
++
  = 11.  Appendix I: Field Installation Photo =

Changes for page WSC1-L-Dragino LoRaWAN Weather Station User Manual

Summary

Details

Applications

Navigation