Changes for page WSC1-L-Dragino LoRaWAN Weather Station User Manual

Last modified by Mengting Qiu on 2025/06/10 18:53

From 77.1 to 76.1 From 79.8 to 79.7

From version 79.7

edited by Xiaoling
on 2022/06/24 16:50

Change comment: There is no comment for this version

To version 77.1

edited by Xiaoling
on 2022/06/24 16:14

Change comment: Uploaded new attachment "1656058463455-569.png", version {1}

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -61,16 +61,14 @@
  [[image:1656042136605-251.png]]
--(% style="color:red" %)**Notice 1:**
++(% style="color:red" %) ** Notice 1:**
  * All weather sensors and WSC1-L are powered by MPPT solar recharge controller. MPPT is connected to solar panel and storage battery.
  * WSC1-L has an extra 1000mAh back up battery. So it can work even solar panel and storage battery Fails.
  * Weather sensors won’t work if solar panel and storage battery fails.
++(% style="color:red" %)** Notice 2:**
--
--(% style="color:red" %)**Notice 2:**
--
  Due to shipment and importation limitation, user is better to purchase below parts locally:
  * Solar Panel
@@ -80,9 +80,6 @@
  * Cabinet.
--
--
--
  == 2.2  How it works? ==
  (((
@@ -90,9 +90,7 @@
  )))
--(((
  Open WSC1-L and put the yellow jumper as below position to power on WSC1-L.
--)))
  [[image:1656042192857-709.png]]
@@ -103,8 +103,6 @@
 . User can send a downlink command to WSC1-L to do a re-scan on the available sensors.
--
--
  == 2.3  Example to use for LoRaWAN network ==
  This section shows an example for how to join the TTN V3 LoRaWAN IoT server. Usages with other LoRaWAN IoT servers are of similar procedure.
@@ -147,9 +147,7 @@
--(((
  (% style="color:blue" %)**Step 2**(%%): Power on WSC1-L, it will start to join TTN server. After join success, it will start to upload sensor data to TTN V3 and user can see in the panel.
--)))
  [[image:1656042745346-283.png]]
@@ -163,9 +163,6 @@
  * Valid Sensor Value: Use FPORT=2
  * Other control command: Use FPORT other than 2.
--
--
--
  === 2.4.1  Uplink FPORT~=5, Device Status ===
  Uplink the device configures with FPORT=5. Once WSC1-L Joined the network, it will uplink this message to the server. After first uplink, WSC1-L will uplink Device Status every 12 hours
@@ -230,13 +230,9 @@
  ==== (% style="color:#037691" %)**BAT:**(%%) ====
--(((
  shows the battery voltage for WSC1-L MCU.
--)))
--(((
  Ex1: 0x0BD6/1000 = 3.03 V
--)))
@@ -304,41 +304,21 @@
  [[image:image-20220624140352-2.png]]
--(((
  Below is an example payload:  [[image:image-20220624140615-3.png]]
--)))
--(((
--
--)))
--(((
  When sending this payload to LoRaWAN server. WSC1-L will send this in one uplink or several uplinks according to LoRaWAN spec requirement. For example, total length of Payload is 54 bytes.
--)))
--* (((
--When WSC1-L sending in US915 frequency DR0 data rate. Because this data rate has limitation of 11 bytes payload for each uplink. The payload will be split into below packets and uplink.
--)))
++* When WSC1-L sending in US915 frequency DR0 data rate. Because this data rate has limitation of 11 bytes payload for each uplink. The payload will be split into below packets and uplink.
--(((
            Uplink 1:  [[image:image-20220624140735-4.png]]
--)))
--(((
            Uplink 2:  [[image:image-20220624140842-5.png]]
--)))
--(((
--
--)))
--* (((
--When WSC1-L sending in EU868 frequency DR0 data rate. The payload will be split into below packets and uplink:
--)))
++* When WSC1-L sending in EU868 frequency DR0 data rate. The payload will be split into below packets and uplink:
--(((
            Uplink 1:  [[image:image-20220624141025-6.png]]
--)))
            Uplink 2:   [[image:image-20220624141100-7.png]]
@@ -437,8 +437,6 @@
  * Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
--
--
  == 3.2  Set Emergency Mode ==
  Feature: In emergency mode, WSC1-L will uplink data every 1 minute.
@@ -454,8 +454,6 @@
  * 0xE100     Same as: AT+ALARMMOD=0
--
--
  == 3.3  Add or Delete RS485 Sensor ==
  Feature: User can add or delete 3^^rd^^ party sensor as long they are RS485/Modbus interface,baud rate support 9600.Maximum can add 4 sensors.
@@ -526,8 +526,6 @@
  * 0xE5FF
--
--
  == 3.4  RS485 Test Command ==
  (% style="color:#037691" %)**AT Command:**
@@ -550,8 +550,6 @@
  * 0xE20103000001840A     Same as: AT+RSWRITE=0103000001840A
--
--
  == 3.5  RS485 response timeout ==
  Feature: Set or get extended time to receive 485 sensor data.
@@ -576,8 +576,6 @@
  * Example 2: Downlink Payload: E000000A ~/~/ Set Transmit Interval (DTR) = 10 seconds
--
--
  == 3.6  Set Sensor Type ==
  Feature: Set sensor in used. If there are 6 sensors, user can set to only send 5 sensors values.
@@ -656,9 +656,6 @@
  * IP Rating: IP65
  * Support default sensors or 3rd party RS485 sensors
--
--
--
  == 5.2  Power Consumption ==
  WSC1-L (without external sensor): Idle: 4mA, Transmit: max 40mA
@@ -726,9 +726,6 @@
  * ABS enclosure.
  * Horizontal adjustable.
--
--
--
  === 6.1.2  Specification ===
  * Resolution: 0.2mm
@@ -740,9 +740,6 @@
  * Working Humidity: <100% (no dewing)
  * Power Consumption: 4mA @ 12v.
--
--
--
  === 6.1.3  Dimension ===
   [[image:1656054957406-980.png]]
@@ -801,9 +801,6 @@
  * RS485 wind speed / direction sensor
  * PC enclosure, resist corrosion
--
--
--
  === 6.2.2  Specification ===
  * Wind speed range: 0 ~~ 30m/s, (always show 30m/s for higher speed)
@@ -817,9 +817,6 @@
  * Power Consumption: 13mA ~~ 12v.
  * Cable Length: 2 meters
--
--
--
  === 6.2.3  Dimension ===
  [[image:image-20220624152813-2.png]]
@@ -866,9 +866,6 @@
  * NDIR to measure CO2 with Internal Temperature Compensation
  * Laser Beam Scattering to PM2.5 and PM10
--
--
--
  === 6.3.2  Specification ===
  * CO2 Range: 0～5000ppm, accuracy: ±3%F•S（25℃）
@@ -886,9 +886,6 @@
  ** CO2: 0～95%RH
  * Power Consumption: 50mA@ 12v.
--
--
--
  === 6.3.3  Dimension ===
  [[image:1656056708366-230.png]]
@@ -933,9 +933,6 @@
  * Surface heating to dry
  * grid electrode uses Electroless Nickel/Immersion Gold design for resist corrosion
--
--
--
  === 6.4.2  Specification ===
  * Detect if there is rain or snow
@@ -947,9 +947,6 @@
  ** No heating: 12mA @ 12v,
  ** heating: 94ma @ 12v.
--
--
--
  === 6.4.3  Dimension ===
  [[image:1656056844782-155.png]]
@@ -996,9 +996,6 @@
  * RS485 Temperature, Humidity, Illuminance, Pressure sensor
--
--
--
  === 6.5.2  Specification ===
  * Input Power: DC 12 ~~ 24v
@@ -1023,9 +1023,6 @@
  * Working Humidity: 10～90%RH
  * Power Consumption: 4mA @ 12v
--
--
--
  === 6.5.3  Dimension ===
  [[image:1656057170639-522.png]]
@@ -1069,9 +1069,6 @@
  * Measure Total Radiation between 0.3～3μm（300～3000nm）
  * Measure Reflected Radiation if sense area towards ground.
--
--
--
  === 6.6.2  Specification ===
  * Input Power: DC 5 ~~ 24v
@@ -1087,9 +1087,6 @@
  * Working Humidity: 10～90%RH
  * Power Consumption: 4mA @ 12v
--
--
--
  === 6.6.3  Dimension ===
  [[image:1656057348695-898.png]]
@@ -1146,9 +1146,6 @@
  * Working Humidity: 10～90%RH
  * Power Consumption: 3mA @ 12v
--
--
--
  === 6.7.3  Dimension ===
  [[image:1656057538793-888.png]]
@@ -1235,6 +1235,9 @@
  * (% style="color:red" %)**IN865**(%%): LoRaWAN IN865 band
  * (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
++
++
++
  == 9.2  Sensors ==
  (% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:510px" %)
@@ -1255,6 +1255,9 @@
  * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:file:///D:/市场资料/说明书/LoRa/LT系列/support@dragino.com]]
++
++
++
  = 11.  Appendix I: Field Installation Photo =
@@ -1264,36 +1264,34 @@
--**Wind Speed/Direction**
++Wind Speed/Direction.
  [[image:1656058373174-421.png]]
--**Total Solar Radiation sensor**
++Total Solar Radiation sensor
  [[image:1656058397364-282.png]]
--**PAR Sensor**
++PAR Sensor
  [[image:1656058416171-615.png]]
--**CO2/PM2.5/PM10 3 in 1 sensor**
++CO2/PM2.5/PM10 3 in 1 sensor
--[[image:1656058441194-827.png]]
++[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image044.png]]
++Rain / Snow Detect:
--**Rain / Snow Detect**
++[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image045.png]]
--[[image:1656058451456-166.png]]
++Rain Gauge.
--
--**Rain Gauge**
--
--[[image:1656058463455-569.png]]
++[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image046.png]]

Changes for page WSC1-L-Dragino LoRaWAN Weather Station User Manual

Summary

Details

Applications

Navigation