Changes for page WSC1-L-Dragino LoRaWAN Weather Station User Manual

Last modified by Mengting Qiu on 2025/06/10 18:53

From 79.21 to 79.22 From 85.1 to 85.2

From version 79.22

edited by Xiaoling
on 2022/06/24 17:23

Change comment: There is no comment for this version

To version 85.1

edited by Xiaoling
on 2022/06/24 18:08

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -99,6 +99,7 @@
 . User can send a downlink command to WSC1-L to do a re-scan on the available sensors.
++
  == 2.3  Example to use for LoRaWAN network ==
  This section shows an example for how to join the TTN V3 LoRaWAN IoT server. Usages with other LoRaWAN IoT servers are of similar procedure.
@@ -158,6 +158,7 @@
  * Other control command: Use FPORT other than 2.
++
  === 2.4.1  Uplink FPORT~=5, Device Status ===
  Uplink the device configures with FPORT=5. Once WSC1-L Joined the network, it will uplink this message to the server. After first uplink, WSC1-L will uplink Device Status every 12 hours
@@ -373,12 +373,21 @@
  == 2.5  Show data on Application Server ==
++(((
  Application platform provides a human friendly interface to show the sensor data, once we have sensor data in TTN V3, we can use Datacake to connect to TTN V3 and see the data in Datacake. Below are the steps:
++)))
++(((
++
++)))
++(((
  (% style="color:blue" %)**Step 1**(%%): Be sure that your device is programmed and properly connected to the LoRaWAN network.
++)))
++(((
  (% style="color:blue" %)**Step 2**(%%): Configure your Application to forward data to Datacake you will need to add integration. Go to TTN V3 Console ~-~-> Applications ~-~-> Integrations ~-~-> Add Integrations.
++)))
  [[image:1656051197172-131.png]]
@@ -426,9 +426,6 @@
--
--
--
  == 3.1  Set Transmit Interval Time ==
  Feature: Change LoRaWAN End Node Transmit Interval.
@@ -448,6 +448,7 @@
  * Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
++
  == 3.2  Set Emergency Mode ==
  Feature: In emergency mode, WSC1-L will uplink data every 1 minute.
@@ -463,27 +463,54 @@
  * 0xE100     Same as: AT+ALARMMOD=0
++
  == 3.3  Add or Delete RS485 Sensor ==
++(((
  Feature: User can add or delete 3^^rd^^ party sensor as long they are RS485/Modbus interface,baud rate support 9600.Maximum can add 4 sensors.
++)))
++(((
  (% style="color:#037691" %)**AT Command: **
++)))
++(((
  (% style="color:blue" %)**AT+DYSENSOR=Type_Code, Query_Length, Query_Command , Read_Length , Valid_Data ,has_CRC,timeout**
++)))
--* Type_Code range:   A1 ~~ A4
--* Query_Length:        RS485 Query frame length, Value cannot be greater than 10
--* Query_Command:  RS485 Query frame data to be sent to sensor, cannot be larger than 10 bytes
--* Read_Length:   RS485 response frame length supposed to receive. Max can receive
--* Valid_Data:       valid data from RS485 Response, Valid Data will be added to Payload and upload via LoRaWAN.
--* has_CRC:          RS485 Response crc check  (0: no verification required 1: verification required). If CRC=1 and CRC error, valid data will be set to 0.
--* timeout:           RS485 receive timeout (uint:ms). Device will close receive window after timeout
++* (((
++Type_Code range:   A1 ~~ A4
++)))
++* (((
++Query_Length:        RS485 Query frame length, Value cannot be greater than 10
++)))
++* (((
++Query_Command:  RS485 Query frame data to be sent to sensor, cannot be larger than 10 bytes
++)))
++* (((
++Read_Length:   RS485 response frame length supposed to receive. Max can receive
++)))
++* (((
++Valid_Data:       valid data from RS485 Response, Valid Data will be added to Payload and upload via LoRaWAN.
++)))
++* (((
++has_CRC:          RS485 Response crc check  (0: no verification required 1: verification required). If CRC=1 and CRC error, valid data will be set to 0.
++)))
++* (((
++timeout:           RS485 receive timeout (uint:ms). Device will close receive window after timeout
++)))
++(((
  **Example:**
++)))
++(((
  User need to change external sensor use the type code as address code.
++)))
++(((
  With a 485 sensor, after correctly changing the address code to A1, the RS485 query frame is shown in the following table:
++)))
  [[image:image-20220624143553-10.png]]
@@ -533,6 +533,7 @@
  * 0xE5FF
++
  == 3.4  RS485 Test Command ==
  (% style="color:#037691" %)**AT Command:**
@@ -555,6 +555,7 @@
  * 0xE20103000001840A     Same as: AT+RSWRITE=0103000001840A
++
  == 3.5  RS485 response timeout ==
  Feature: Set or get extended time to receive 485 sensor data.
@@ -579,6 +579,7 @@
  * Example 2: Downlink Payload: E000000A ~/~/ Set Transmit Interval (DTR) = 10 seconds
++
  == 3.6  Set Sensor Type ==
  (((
@@ -662,6 +662,7 @@
  * Support default sensors or 3rd party RS485 sensors
++
  == 5.2  Power Consumption ==
  WSC1-L (without external sensor): Idle: 4mA, Transmit: max 40mA
@@ -730,6 +730,7 @@
  * Horizontal adjustable.
++
  === 6.1.2  Specification ===
  * Resolution: 0.2mm
@@ -742,6 +742,7 @@
  * Power Consumption: 4mA @ 12v.
++
  === 6.1.3  Dimension ===
   [[image:1656054957406-980.png]]
@@ -813,6 +813,7 @@
  * PC enclosure, resist corrosion
++
  === 6.2.2  Specification ===
  * Wind speed range: 0 ~~ 30m/s, (always show 30m/s for higher speed)
@@ -827,6 +827,7 @@
  * Cable Length: 2 meters
++
  === 6.2.3  Dimension ===
  [[image:image-20220624152813-2.png]]
@@ -878,6 +878,7 @@
  * Laser Beam Scattering to PM2.5 and PM10
++
  === 6.3.2  Specification ===
  * CO2 Range: 0～5000ppm, accuracy: ±3%F•S（25℃）
@@ -896,6 +896,7 @@
  * Power Consumption: 50mA@ 12v.
++
  === 6.3.3  Dimension ===
  [[image:1656056708366-230.png]]
@@ -939,6 +939,7 @@
  * grid electrode uses Electroless Nickel/Immersion Gold design for resist corrosion
++
  === 6.4.2  Specification ===
  * Detect if there is rain or snow
@@ -951,6 +951,7 @@
  ** heating: 94ma @ 12v.
++
  === 6.4.3  Dimension ===
  [[image:1656056844782-155.png]]
@@ -1000,6 +1000,7 @@
  * RS485 Temperature, Humidity, Illuminance, Pressure sensor
++
  === 6.5.2  Specification ===
  * Input Power: DC 12 ~~ 24v
@@ -1025,6 +1025,7 @@
  * Power Consumption: 4mA @ 12v
++
  === 6.5.3  Dimension ===
  [[image:1656057170639-522.png]]
@@ -1085,6 +1085,7 @@
  * Power Consumption: 4mA @ 12v
++
  === 6.6.3  Dimension ===
  [[image:1656057348695-898.png]]
@@ -1146,6 +1146,7 @@
  * Power Consumption: 3mA @ 12v
++
  === 6.7.3  Dimension ===
  [[image:1656057538793-888.png]]
@@ -1261,11 +1261,10 @@
--
  = 11.  Appendix I: Field Installation Photo =
--[[image:1656058346362-132.png]]
++[[image:1656058346362-132.png||height="685" width="732"]]
  **Storage Battery**: 12v,12AH li battery
@@ -1273,13 +1273,13 @@
  **Wind Speed/Direction**
--[[image:1656058373174-421.png]]
++[[image:1656058373174-421.png||height="356" width="731"]]
  **Total Solar Radiation sensor**
--[[image:1656058397364-282.png]]
++[[image:1656058397364-282.png||height="453" width="732"]]
@@ -1291,7 +1291,7 @@
  **CO2/PM2.5/PM10 3 in 1 sensor**
--[[image:1656058441194-827.png]]
++[[image:1656058441194-827.png||height="672" width="523"]]
@@ -1303,4 +1303,4 @@
  **Rain Gauge**
--[[image:1656058463455-569.png]]
++[[image:1656058463455-569.png||height="499" width="550"]]