Changes for page WSC1-L-Dragino LoRaWAN Weather Station User Manual

Last modified by Xiaoling on 2025/05/07 14:00

From version < 79.16 >

edited by Xiaoling
on 2022/06/24 17:20

To version < 78.2 >

edited by Xiaoling
on 2022/06/24 16:16

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -61,16 +61,14 @@
  [[image:1656042136605-251.png]]
--(% style="color:red" %)**Notice 1:**
++(% style="color:red" %) ** Notice 1:**
  * All weather sensors and WSC1-L are powered by MPPT solar recharge controller. MPPT is connected to solar panel and storage battery.
  * WSC1-L has an extra 1000mAh back up battery. So it can work even solar panel and storage battery Fails.
  * Weather sensors won’t work if solar panel and storage battery fails.
++(% style="color:red" %)** Notice 2:**
--
--(% style="color:red" %)**Notice 2:**
--
  Due to shipment and importation limitation, user is better to purchase below parts locally:
  * Solar Panel
@@ -79,10 +79,6 @@
  * Mounting Kit includes pole and mast assembly. Each weather sensor has it’s own mounting assembly, user can check the sensor section in this manual.
  * Cabinet.
--
--
--
--
  == 2.2  How it works? ==
  (((
@@ -90,9 +90,7 @@
  )))
--(((
  Open WSC1-L and put the yellow jumper as below position to power on WSC1-L.
--)))
  [[image:1656042192857-709.png]]
@@ -102,9 +102,6 @@
 . WSC1-L will auto scan available weather sensors when power on or reboot.
 . User can send a downlink command to WSC1-L to do a re-scan on the available sensors.
--
--
--
  == 2.3  Example to use for LoRaWAN network ==
  This section shows an example for how to join the TTN V3 LoRaWAN IoT server. Usages with other LoRaWAN IoT servers are of similar procedure.
@@ -147,9 +147,7 @@
--(((
  (% style="color:blue" %)**Step 2**(%%): Power on WSC1-L, it will start to join TTN server. After join success, it will start to upload sensor data to TTN V3 and user can see in the panel.
--)))
  [[image:1656042745346-283.png]]
@@ -163,9 +163,6 @@
  * Valid Sensor Value: Use FPORT=2
  * Other control command: Use FPORT other than 2.
--
--
--
  === 2.4.1  Uplink FPORT~=5, Device Status ===
  Uplink the device configures with FPORT=5. Once WSC1-L Joined the network, it will uplink this message to the server. After first uplink, WSC1-L will uplink Device Status every 12 hours
@@ -230,13 +230,9 @@
  ==== (% style="color:#037691" %)**BAT:**(%%) ====
--(((
  shows the battery voltage for WSC1-L MCU.
--)))
--(((
  Ex1: 0x0BD6/1000 = 3.03 V
--)))
@@ -304,50 +304,22 @@
  [[image:image-20220624140352-2.png]]
--(((
  Below is an example payload:  [[image:image-20220624140615-3.png]]
--)))
--(((
--
--)))
--(((
  When sending this payload to LoRaWAN server. WSC1-L will send this in one uplink or several uplinks according to LoRaWAN spec requirement. For example, total length of Payload is 54 bytes.
--)))
--* (((
--When WSC1-L sending in US915 frequency DR0 data rate. Because this data rate has limitation of 11 bytes payload for each uplink. The payload will be split into below packets and uplink.
--)))
++* When WSC1-L sending in US915 frequency DR0 data rate. Because this data rate has limitation of 11 bytes payload for each uplink. The payload will be split into below packets and uplink.
--(((
            Uplink 1:  [[image:image-20220624140735-4.png]]
--)))
--(((
--
--)))
--
--(((
            Uplink 2:  [[image:image-20220624140842-5.png]]
--)))
--(((
--
--)))
--* (((
--When WSC1-L sending in EU868 frequency DR0 data rate. The payload will be split into below packets and uplink:
--)))
++* When WSC1-L sending in EU868 frequency DR0 data rate. The payload will be split into below packets and uplink:
--(((
            Uplink 1:  [[image:image-20220624141025-6.png]]
--)))
--(((
--
--)))
--
            Uplink 2:   [[image:image-20220624141100-7.png]]
@@ -444,9 +444,6 @@
  * Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
  * Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
--
--
--
  == 3.2  Set Emergency Mode ==
  Feature: In emergency mode, WSC1-L will uplink data every 1 minute.
@@ -461,9 +461,6 @@
  * 0xE101     Same as: AT+ALARMMOD=1
  * 0xE100     Same as: AT+ALARMMOD=0
--
--
--
  == 3.3  Add or Delete RS485 Sensor ==
  Feature: User can add or delete 3^^rd^^ party sensor as long they are RS485/Modbus interface,baud rate support 9600.Maximum can add 4 sensors.
@@ -533,9 +533,6 @@
  * 0xE5FF
--
--
--
  == 3.4  RS485 Test Command ==
  (% style="color:#037691" %)**AT Command:**
@@ -557,9 +557,6 @@
  * 0xE20103000001840A     Same as: AT+RSWRITE=0103000001840A
--
--
--
  == 3.5  RS485 response timeout ==
  Feature: Set or get extended time to receive 485 sensor data.
@@ -583,18 +583,11 @@
  * Example 1: Downlink Payload: E0000005 ~/~/ Set Transmit Interval (DTR) = 5 seconds
  * Example 2: Downlink Payload: E000000A ~/~/ Set Transmit Interval (DTR) = 10 seconds
--
--
--
  == 3.6  Set Sensor Type ==
--(((
  Feature: Set sensor in used. If there are 6 sensors, user can set to only send 5 sensors values.
--)))
--(((
  See [[definition>>||anchor="HWeatherSensorTypes:"]] for the sensor type.
--)))
  [[image:image-20220624144904-12.png]]
@@ -668,9 +668,6 @@
  * IP Rating: IP65
  * Support default sensors or 3rd party RS485 sensors
--
--
--
  == 5.2  Power Consumption ==
  WSC1-L (without external sensor): Idle: 4mA, Transmit: max 40mA
@@ -738,9 +738,6 @@
  * ABS enclosure.
  * Horizontal adjustable.
--
--
--
  === 6.1.2  Specification ===
  * Resolution: 0.2mm
@@ -752,9 +752,6 @@
  * Working Humidity: <100% (no dewing)
  * Power Consumption: 4mA @ 12v.
--
--
--
  === 6.1.3  Dimension ===
   [[image:1656054957406-980.png]]
@@ -767,31 +767,19 @@
  === 6.1.5  Installation Notice ===
--(((
  Do not power on while connect the cables. Double check the wiring before power on.
--)))
--(((
  Installation Photo as reference:
--)))
--(((
  (% style="color:#4472c4" %)** Install on Ground:**
--)))
--(((
  WSS-01 Rain Gauge include screws so can install in ground directly .
--)))
--(((
  (% style="color:#4472c4" %)** Install on pole:**
--)))
--(((
  If user want to install on pole, they can purchase the (% style="color:#4472c4" %)** WS-K2 :  Bracket Kit for Pole installation**(%%), and install as below:
--)))
  [[image:image-20220624152218-1.png||height="526" width="276"]]
@@ -825,9 +825,6 @@
  * RS485 wind speed / direction sensor
  * PC enclosure, resist corrosion
--
--
--
  === 6.2.2  Specification ===
  * Wind speed range: 0 ~~ 30m/s, (always show 30m/s for higher speed)
@@ -841,9 +841,6 @@
  * Power Consumption: 13mA ~~ 12v.
  * Cable Length: 2 meters
--
--
--
  === 6.2.3  Dimension ===
  [[image:image-20220624152813-2.png]]
@@ -861,13 +861,9 @@
  === 6.2.6  Installation Notice ===
--(((
  Do not power on while connect the cables. Double check the wiring before power on.
--)))
--(((
  The sensor must be installed with below direction, towards North.
--)))
  [[image:image-20220624153901-3.png]]
@@ -894,9 +894,6 @@
  * NDIR to measure CO2 with Internal Temperature Compensation
  * Laser Beam Scattering to PM2.5 and PM10
--
--
--
  === 6.3.2  Specification ===
  * CO2 Range: 0～5000ppm, accuracy: ±3%F•S（25℃）
@@ -914,9 +914,6 @@
  ** CO2: 0～95%RH
  * Power Consumption: 50mA@ 12v.
--
--
--
  === 6.3.3  Dimension ===
  [[image:1656056708366-230.png]]
@@ -931,6 +931,8 @@
  Do not power on while connect the cables. Double check the wiring before power on.
++[[image:1656057016033-551.png]]
++
  [[image:1656056751153-304.png]]
  [[image:1656056766224-773.png]]
@@ -959,9 +959,6 @@
  * Surface heating to dry
  * grid electrode uses Electroless Nickel/Immersion Gold design for resist corrosion
--
--
--
  === 6.4.2  Specification ===
  * Detect if there is rain or snow
@@ -973,9 +973,6 @@
  ** No heating: 12mA @ 12v,
  ** heating: 94ma @ 12v.
--
--
--
  === 6.4.3  Dimension ===
  [[image:1656056844782-155.png]]
@@ -991,9 +991,7 @@
  Do not power on while connect the cables. Double check the wiring before power on.
--(((
  Install with 15°degree.
--)))
   [[image:1656056873783-780.png]]
@@ -1024,9 +1024,6 @@
  * RS485 Temperature, Humidity, Illuminance, Pressure sensor
--
--
--
  === 6.5.2  Specification ===
  * Input Power: DC 12 ~~ 24v
@@ -1051,9 +1051,6 @@
  * Working Humidity: 10～90%RH
  * Power Consumption: 4mA @ 12v
--
--
--
  === 6.5.3  Dimension ===
  [[image:1656057170639-522.png]]
@@ -1097,9 +1097,6 @@
  * Measure Total Radiation between 0.3～3μm（300～3000nm）
  * Measure Reflected Radiation if sense area towards ground.
--
--
--
  === 6.6.2  Specification ===
  * Input Power: DC 5 ~~ 24v
@@ -1115,9 +1115,6 @@
  * Working Humidity: 10～90%RH
  * Power Consumption: 4mA @ 12v
--
--
--
  === 6.6.3  Dimension ===
  [[image:1656057348695-898.png]]
@@ -1156,13 +1156,9 @@
  === 6.7.1  Feature ===
--(((
  PAR (Photosynthetically Available Radiation) sensor measure 400 ~~ 700nm wavelength nature light's Photosynthetically Available Radiation.
--)))
--(((
  When nature light shine on the sense area, it will generate a signal base on the incidence radiation strength.
--)))
  === 6.7.2  Specification ===
@@ -1178,9 +1178,6 @@
  * Working Humidity: 10～90%RH
  * Power Consumption: 3mA @ 12v
--
--
--
  === 6.7.3  Dimension ===
  [[image:1656057538793-888.png]]
@@ -1267,10 +1267,12 @@
  * (% style="color:red" %)**IN865**(%%): LoRaWAN IN865 band
  * (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
++
++
  == 9.2  Sensors ==
--(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:350px" %)
--|=(% style="width: 300px;" %)**Sensor Model**|=(% style="width: 50px;" %)**Part Number**
++(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:510px" %)
++|=(% style="width: 462px;" %)**Sensor Model**|=(% style="width: 110px;" %)**Part Number**
  |(% style="width:462px" %)**Rain Gauge**|(% style="width:110px" %)WSS-01
  |(% style="width:462px" %)**Rain Gauge installation Bracket for Pole**|(% style="width:110px" %)WS-K2
  |(% style="width:462px" %)**Wind Speed Direction 2 in 1 Sensor**|(% style="width:110px" %)WSS-02
@@ -1281,6 +1281,8 @@
  |(% style="width:462px" %)**PAR (Photosynthetically Available Radiation)**|(% style="width:110px" %)WSS-07
++
++
  = 10.  Support =
  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
@@ -1287,6 +1287,8 @@
  * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:file:///D:/市场资料/说明书/LoRa/LT系列/support@dragino.com]]
++
++
  = 11.  Appendix I: Field Installation Photo =

Changes for page WSC1-L-Dragino LoRaWAN Weather Station User Manual

Summary

Details

Applications

Navigation