Changes for page WSC1-L-Dragino LoRaWAN Weather Station User Manual

Last modified by Xiaoling on 2025/04/25 09:08

From version < 46.4 >

edited by Xiaoling
on 2022/06/24 15:43

To version < 46.6 >

edited by Xiaoling
on 2022/06/24 15:44

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -68,7 +68,6 @@
  * Weather sensors won’t work if solar panel and storage battery fails.
--
  (% style="color:red" %)** Notice 2:**
  Due to shipment and importation limitation, user is better to purchase below parts locally:
@@ -83,7 +83,6 @@
--
  == 2.2  How it works? ==
  (((
@@ -105,7 +105,6 @@
--
  == 2.3  Example to use for LoRaWAN network ==
  This section shows an example for how to join the TTN V3 LoRaWAN IoT server. Usages with other LoRaWAN IoT servers are of similar procedure.
@@ -162,7 +162,6 @@
  * Valid Sensor Value: Use FPORT=2
  * Other control command: Use FPORT other than 2.
--
  === 2.4.1  Uplink FPORT~=5, Device Status ===
  Uplink the device configures with FPORT=5. Once WSC1-L Joined the network, it will uplink this message to the server. After first uplink, WSC1-L will uplink Device Status every 12 hours
@@ -413,7 +413,6 @@
--
  == 3.2  Set Emergency Mode ==
  Feature: In emergency mode, WSC1-L will uplink data every 1 minute.
@@ -432,7 +432,6 @@
--
  == 3.3  Add or Delete RS485 Sensor ==
  Feature: User can add or delete 3^^rd^^ party sensor as long they are RS485/Modbus interface,baud rate support 9600.Maximum can add 4 sensors.
@@ -475,7 +475,6 @@
  * timeout: 1500 (Fill in the test according to the actual situation)
--
  **So the input command is:**
  AT+DYSENSOR=A1,8,A103000000019CAA,8,24,1,1500
@@ -487,7 +487,6 @@
  |=(% style="width: 94px;" %)Type Code|=(% style="width: 121px;" %)Length (Bytes)|=(% style="width: 132px;" %)Measured Value
  |(% style="width:94px" %)A1|(% style="width:121px" %)2|(% style="width:132px" %)0x000A
--
  **Related commands:**
  AT+DYSENSOR=A1,0    ~-~->   Delete 3^^rd^^ party sensor A1.
@@ -509,7 +509,6 @@
--
  == 3.4  RS485 Test Command ==
  (% style="color:#037691" %)**AT Command:**
@@ -535,7 +535,6 @@
--
  == 3.5  RS485 response timeout ==
  Feature: Set or get extended time to receive 485 sensor data.
@@ -563,7 +563,6 @@
--
  == 3.6  Set Sensor Type ==
  Feature: Set sensor in used. If there are 6 sensors, user can set to only send 5 sensors values.
@@ -710,7 +710,6 @@
  * Horizontal adjustable.
--
  === 6.1.2  Specification ===
  * Resolution: 0.2mm
@@ -723,7 +723,6 @@
  * Power Consumption: 4mA @ 12v.
--
  === 6.1.3  Dimension ===
   [[image:1656054957406-980.png]]
@@ -784,7 +784,6 @@
  * PC enclosure, resist corrosion
--
  === 6.2.2  Specification ===
  * Wind speed range: 0 ~~ 30m/s, (always show 30m/s for higher speed)
@@ -799,7 +799,6 @@
  * Cable Length: 2 meters
--
  === 6.2.3  Dimension ===
  [[image:image-20220624152813-2.png]]
@@ -826,19 +826,20 @@
  == 6.3  CO2/PM2.5/PM10 ~-~- WSS-03 ==
++
++(((
  WSS-03 is a RS485 Air Quality sensor. It can monitor CO2, PM2.5 and PM10 at the same time.
++)))
--
++(((
  WSS-03 uses weather proof shield which can make sure the sensors are well protected against UV & radiation.
++)))
++(((
++WSS-03 is designed to support the Dragino Weather station solution. Users only need to connect WSS-03 RS485 interface to WSC1-L. The weather station main processor WSC1-L can detect and upload the environment CO2, PM2.5 and PM10 to the IoT Server via wireless LoRaWAN protocol.
++)))
--WSS-03 is designed to support the Dragino Weather station solution.
--Users only need to connect WSS-03 RS485 interface to WSC1-L. The weather station main
--
--processor WSC1-L can detect and upload the environment CO2, PM2.5 and PM10 to the IoT Server via wireless LoRaWAN protocol.
--
--
  === 6.3.1  Feature ===
  * RS485 CO2, PM2.5, PM10 sensor
@@ -846,7 +846,6 @@
  * Laser Beam Scattering to PM2.5 and PM10
--
  === 6.3.2  Specification ===
  * CO2 Range: 0～5000ppm, accuracy: ±3%F•S（25℃）
@@ -865,7 +865,6 @@
  * Power Consumption: 50mA@ 12v.
--
  === 6.3.3  Dimension ===
  [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image028.png]]
@@ -912,7 +912,6 @@
  * grid electrode uses Electroless Nickel/Immersion Gold design for resist corrosion
--
  === 6.4.2  Specification ===
  * Detect if there is rain or snow
@@ -925,7 +925,6 @@
  ** heating: 94ma @ 12v.
--
  === 6.4.3  Dimension ===
  [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image031.png]]
@@ -976,7 +976,6 @@
  * RS485 Temperature, Humidity, Illuminance, Pressure sensor
--
  === 6.5.2  Specification ===
  * Input Power: DC 12 ~~ 24v
@@ -1002,7 +1002,6 @@
  * Power Consumption: 4mA @ 12v
--
  === 6.5.3  Dimension ===
  [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image034.jpg]]
@@ -1049,7 +1049,6 @@
  * Measure Reflected Radiation if sense area towards ground.
--
  === 6.6.2  Specification ===
  * Input Power: DC 5 ~~ 24v
@@ -1066,7 +1066,6 @@
  * Power Consumption: 4mA @ 12v
--
  === 6.6.3  Dimension ===
  [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image036.png]]
@@ -1125,7 +1125,6 @@
  * Power Consumption: 3mA @ 12v
--
  === 6.7.3  Dimension ===
  [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image036.png]]
@@ -1209,7 +1209,6 @@
  * (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
--
  == 9.2  Sensors ==
  |**Sensor Model**|**Part Number**

Changes for page WSC1-L-Dragino LoRaWAN Weather Station User Manual

Summary

Details

Applications

Navigation