Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -79,7 +79,6 @@
79	79
80	80
81	81
82		-
83	83	== 2.2 How it works? ==
84	84
85	85	(((
...	...	@@ -99,7 +99,6 @@
99	99
100	100
101	101
102		-
103	103	== 2.3 Example to use for LoRaWAN network ==
104	104
105	105	This section shows an example for how to join the TTN V3 LoRaWAN IoT server. Usages with other LoRaWAN IoT servers are of similar procedure.
...	...	@@ -157,7 +157,6 @@
157	157	* Other control command: Use FPORT other than 2.
158	158
159	159
160		-
161	161	=== 2.4.1 Uplink FPORT~=5, Device Status ===
162	162
163	163	Uplink the device configures with FPORT=5. Once WSC1-L Joined the network, it will uplink this message to the server. After first uplink, WSC1-L will uplink Device Status every 12 hours
...	...	@@ -382,6 +382,7 @@
382	382	These commands only valid for WSC1-L, as below:
383	383
384	384
	382	+
385	385	== 3.1 Set Transmit Interval Time ==
386	386
387	387	Feature: Change LoRaWAN End Node Transmit Interval.
...	...	@@ -401,6 +401,8 @@
401	401	* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
402	402
403	403
	402	+
	403	+
404	404	== 3.2 Set Emergency Mode ==
405	405
406	406	Feature: In emergency mode, WSC1-L will uplink data every 1 minute.
...	...	@@ -416,6 +416,8 @@
416	416	* 0xE100     Same as: AT+ALARMMOD=0
417	417
418	418
	419	+
	420	+
419	419	== 3.3 Add or Delete RS485 Sensor ==
420	420
421	421	Feature: User can add or delete 3^^rd^^ party sensor as long they are RS485/Modbus interface,baud rate support 9600.Maximum can add 4 sensors.
...	...	@@ -432,6 +432,8 @@
432	432	* has_CRC:  RS485 Response crc check  (0: no verification required 1: verification required). If CRC=1 and CRC error, valid data will be set to 0.
433	433	* timeout:  RS485 receive timeout (uint:ms). Device will close receive window after timeout
434	434
	437	+
	438	+
435	435	**Example:**
436	436
437	437	User need to change external sensor use the type code as address code.
...	...	@@ -456,6 +456,7 @@
456	456	* has_CRC: 1
457	457	* timeout: 1500 (Fill in the test according to the actual situation)
458	458
	463	+
459	459	**So the input command is:**
460	460
461	461	AT+DYSENSOR=A1,8,A103000000019CAA,8,24,1,1500
...	...	@@ -485,6 +485,8 @@
485	485	* 0xE5FF
486	486
487	487
	493	+
	494	+
488	488	== 3.4 RS485 Test Command ==
489	489
490	490	(% style="color:#037691" %)**AT Command:**
...	...	@@ -507,6 +507,8 @@
507	507	* 0xE20103000001840A     Same as: AT+RSWRITE=0103000001840A
508	508
509	509
	517	+
	518	+
510	510	== 3.5 RS485 response timeout ==
511	511
512	512	Feature: Set or get extended time to receive 485 sensor data.
...	...	@@ -521,6 +521,7 @@
521	521	Range : 0~~10000
522	522	)))|(% style="width:85px" %)OK
523	523
	533	+
524	524	(% style="color:#037691" %)**Downlink Command:**
525	525
526	526	Format: Command Code (0xE0) followed by 3 bytes time value.
...	...	@@ -531,6 +531,8 @@
531	531	* Example 2: Downlink Payload: E000000A ~/~/ Set Transmit Interval (DTR) = 10 seconds
532	532
533	533
	544	+
	545	+
534	534	== 3.6 Set Sensor Type ==
535	535
536	536	Feature: Set sensor in used. If there are 6 sensors, user can set to only send 5 sensors values.
...	...	@@ -540,7 +540,6 @@
540	540	[[image:image-20220624144904-12.png]]
541	541
542	542
543		-
544	544	(% style="color:#037691" %)**AT Command:**
545	545
546	546	(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:377px" %)
...	...	@@ -614,7 +614,6 @@
614	614
615	615
616	616
617		-
618	618	== 5.2 Power Consumption ==
619	619
620	620	WSC1-L (without external sensor): Idle: 4mA, Transmit: max 40mA