Skip to Content
Last modified by Mengting Qiu on 2025/06/10 18:53
From version 32.12
edited by Xiaoling
on 2022/06/24 15:00
Change comment: There is no comment for this version
To version 32.11
edited by Xiaoling
on 2022/06/24 14:59
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -78,6 +78,7 @@
78 78  * Cabinet.
79 79  
80 80  
81 +
81 81  == 2.2 How it works? ==
82 82  
83 83  (((
... ... @@ -96,6 +96,7 @@
96 96  1. User can send a downlink command to WSC1-L to do a re-scan on the available sensors.
97 97  
98 98  
100 +
99 99  == 2.3 Example to use for LoRaWAN network ==
100 100  
101 101  This section shows an example for how to join the TTN V3 LoRaWAN IoT server. Usages with other LoRaWAN IoT servers are of similar procedure.
... ... @@ -153,9 +153,6 @@
153 153  * Other control command: Use FPORT other than 2.
154 154  
155 155  
156 -
157 -
158 -
159 159  === 2.4.1 Uplink FPORT~=5, Device Status ===
160 160  
161 161  Uplink the device configures with FPORT=5. Once WSC1-L Joined the network, it will uplink this message to the server. After first uplink, WSC1-L will uplink Device Status every 12 hours
... ... @@ -401,6 +401,7 @@
401 401  
402 402  
403 403  
403 +
404 404  == 3.2 Set Emergency Mode ==
405 405  
406 406  Feature: In emergency mode, WSC1-L will uplink data every 1 minute.
... ... @@ -417,6 +417,7 @@
417 417  
418 418  
419 419  
420 +
420 420  == 3.3 Add or Delete RS485 Sensor ==
421 421  
422 422  Feature: User can add or delete 3^^rd^^ party sensor as long they are RS485/Modbus interface,baud rate support 9600.Maximum can add 4 sensors.
... ... @@ -434,6 +434,7 @@
434 434  * timeout:  RS485 receive timeout (uint:ms). Device will close receive window after timeout
435 435  
436 436  
438 +
437 437  **Example:**
438 438  
439 439  User need to change external sensor use the type code as address code.
... ... @@ -458,6 +458,7 @@
458 458  * has_CRC: 1
459 459  * timeout: 1500 (Fill in the test according to the actual situation)
460 460  
463 +
461 461  **So the input command is:**
462 462  
463 463  AT+DYSENSOR=A1,8,A103000000019CAA,8,24,1,1500
... ... @@ -488,6 +488,7 @@
488 488  
489 489  
490 490  
494 +
491 491  == 3.4 RS485 Test Command ==
492 492  
493 493  (% style="color:#037691" %)**AT Command:**
... ... @@ -511,6 +511,7 @@
511 511  
512 512  
513 513  
518 +
514 514  == 3.5 RS485 response timeout ==
515 515  
516 516  Feature: Set or get extended time to receive 485 sensor data.
... ... @@ -525,6 +525,7 @@
525 525  Range : 0~~10000
526 526  )))|(% style="width:85px" %)OK
527 527  
533 +
528 528  (% style="color:#037691" %)**Downlink Command:**
529 529  
530 530  Format: Command Code (0xE0) followed by 3 bytes time value.
... ... @@ -536,6 +536,7 @@
536 536  
537 537  
538 538  
545 +
539 539  == 3.6 Set Sensor Type ==
540 540  
541 541  Feature: Set sensor in used. If there are 6 sensors, user can set to only send 5 sensors values.
... ... @@ -617,6 +617,7 @@
617 617  
618 618  
619 619  
627 +
620 620  == 5.2 Power Consumption ==
621 621  
622 622  WSC1-L (without external sensor): Idle: 4mA, Transmit: max 40mA