Skip to Content
Last modified by Mengting Qiu on 2025/06/10 18:53
From version 32.11
edited by Xiaoling
on 2022/06/24 14:59
Change comment: There is no comment for this version
To version 32.10
edited by Xiaoling
on 2022/06/24 14:59
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -79,6 +79,7 @@
79 79  
80 80  
81 81  
82 +
82 82  == 2.2 How it works? ==
83 83  
84 84  (((
... ... @@ -98,6 +98,7 @@
98 98  
99 99  
100 100  
102 +
101 101  == 2.3 Example to use for LoRaWAN network ==
102 102  
103 103  This section shows an example for how to join the TTN V3 LoRaWAN IoT server. Usages with other LoRaWAN IoT servers are of similar procedure.
... ... @@ -155,6 +155,7 @@
155 155  * Other control command: Use FPORT other than 2.
156 156  
157 157  
160 +
158 158  === 2.4.1 Uplink FPORT~=5, Device Status ===
159 159  
160 160  Uplink the device configures with FPORT=5. Once WSC1-L Joined the network, it will uplink this message to the server. After first uplink, WSC1-L will uplink Device Status every 12 hours
... ... @@ -401,6 +401,7 @@
401 401  
402 402  
403 403  
407 +
404 404  == 3.2 Set Emergency Mode ==
405 405  
406 406  Feature: In emergency mode, WSC1-L will uplink data every 1 minute.
... ... @@ -418,6 +418,7 @@
418 418  
419 419  
420 420  
425 +
421 421  == 3.3 Add or Delete RS485 Sensor ==
422 422  
423 423  Feature: User can add or delete 3^^rd^^ party sensor as long they are RS485/Modbus interface,baud rate support 9600.Maximum can add 4 sensors.
... ... @@ -434,8 +434,6 @@
434 434  * has_CRC:  RS485 Response crc check  (0: no verification required 1: verification required). If CRC=1 and CRC error, valid data will be set to 0.
435 435  * timeout:  RS485 receive timeout (uint:ms). Device will close receive window after timeout
436 436  
437 -
438 -
439 439  **Example:**
440 440  
441 441  User need to change external sensor use the type code as address code.
... ... @@ -460,7 +460,6 @@
460 460  * has_CRC: 1
461 461  * timeout: 1500 (Fill in the test according to the actual situation)
462 462  
463 -
464 464  **So the input command is:**
465 465  
466 466  AT+DYSENSOR=A1,8,A103000000019CAA,8,24,1,1500
... ... @@ -492,6 +492,7 @@
492 492  
493 493  
494 494  
497 +
495 495  == 3.4 RS485 Test Command ==
496 496  
497 497  (% style="color:#037691" %)**AT Command:**
... ... @@ -516,6 +516,7 @@
516 516  
517 517  
518 518  
522 +
519 519  == 3.5 RS485 response timeout ==
520 520  
521 521  Feature: Set or get extended time to receive 485 sensor data.
... ... @@ -530,7 +530,6 @@
530 530  Range : 0~~10000
531 531  )))|(% style="width:85px" %)OK
532 532  
533 -
534 534  (% style="color:#037691" %)**Downlink Command:**
535 535  
536 536  Format: Command Code (0xE0) followed by 3 bytes time value.
... ... @@ -543,6 +543,7 @@
543 543  
544 544  
545 545  
549 +
546 546  == 3.6 Set Sensor Type ==
547 547  
548 548  Feature: Set sensor in used. If there are 6 sensors, user can set to only send 5 sensors values.
... ... @@ -552,6 +552,7 @@
552 552  [[image:image-20220624144904-12.png]]
553 553  
554 554  
559 +
555 555  (% style="color:#037691" %)**AT Command:**
556 556  
557 557  (% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:377px" %)
... ... @@ -625,6 +625,7 @@
625 625  
626 626  
627 627  
633 +
628 628  == 5.2 Power Consumption ==
629 629  
630 630  WSC1-L (without external sensor): Idle: 4mA, Transmit: max 40mA