Skip to Content
Last modified by Mengting Qiu on 2025/06/10 18:53
From version 31.4
edited by Xiaoling
on 2022/06/24 14:41
Change comment: There is no comment for this version
To version 32.12
edited by Xiaoling
on 2022/06/24 15:00
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -77,6 +77,7 @@
77 77  * Mounting Kit includes pole and mast assembly. Each weather sensor has it’s own mounting assembly, user can check the sensor section in this manual.
78 78  * Cabinet.
79 79  
80 +
80 80  == 2.2 How it works? ==
81 81  
82 82  (((
... ... @@ -94,6 +94,7 @@
94 94  1. WSC1-L will auto scan available weather sensors when power on or reboot.
95 95  1. User can send a downlink command to WSC1-L to do a re-scan on the available sensors.
96 96  
98 +
97 97  == 2.3 Example to use for LoRaWAN network ==
98 98  
99 99  This section shows an example for how to join the TTN V3 LoRaWAN IoT server. Usages with other LoRaWAN IoT servers are of similar procedure.
... ... @@ -150,6 +150,10 @@
150 150  * Valid Sensor Value: Use FPORT=2
151 151  * Other control command: Use FPORT other than 2.
152 152  
155 +
156 +
157 +
158 +
153 153  === 2.4.1 Uplink FPORT~=5, Device Status ===
154 154  
155 155  Uplink the device configures with FPORT=5. Once WSC1-L Joined the network, it will uplink this message to the server. After first uplink, WSC1-L will uplink Device Status every 12 hours
... ... @@ -374,6 +374,7 @@
374 374  These commands only valid for WSC1-L, as below:
375 375  
376 376  
383 +
377 377  == 3.1 Set Transmit Interval Time ==
378 378  
379 379  Feature: Change LoRaWAN End Node Transmit Interval.
... ... @@ -441,7 +441,7 @@
441 441  [[image:image-20220624143618-11.png]]
442 442  
443 443  
444 -Then the following parameters should be:
451 +**Then the following parameters should be:**
445 445  
446 446  * Address_Code range: A1
447 447  * Query_Length: 8
... ... @@ -451,7 +451,7 @@
451 451  * has_CRC: 1
452 452  * timeout: 1500 (Fill in the test according to the actual situation)
453 453  
454 -So the input command is:
461 +**So the input command is:**
455 455  
456 456  AT+DYSENSOR=A1,8,A103000000019CAA,8,24,1,1500
457 457  
... ... @@ -458,14 +458,15 @@
458 458  
459 459  In every sampling. WSC1-L will auto append the sensor segment as per this structure and uplink.
460 460  
461 -|Type Code|Length (Bytes)|Measured Value
462 -|A1|2|0x000A
468 +(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:351px" %)
469 +|=(% style="width: 94px;" %)Type Code|=(% style="width: 121px;" %)Length (Bytes)|=(% style="width: 132px;" %)Measured Value
470 +|(% style="width:94px" %)A1|(% style="width:121px" %)2|(% style="width:132px" %)0x000A
463 463  
464 -Related commands:
472 +**Related commands:**
465 465  
466 -AT+DYSENSOR=A1,0 –> Delete 3^^rd^^ party sensor A1.
474 +AT+DYSENSOR=A1,0  ~-~->  Delete 3^^rd^^ party sensor A1.
467 467  
468 -AT+DYSENSOR ~-~-> List All 3^^rd^^ Party Sensor. Like below:
476 +AT+DYSENSOR  ~-~->  List All 3^^rd^^ Party Sensor. Like below:
469 469  
470 470  
471 471  (% style="color:#037691" %)**Downlink Command:  **
... ... @@ -484,12 +484,13 @@
484 484  
485 485  (% style="color:#037691" %)**AT Command:**
486 486  
487 -|**Command Example**|**Function**|**Response**
488 -|AT+RSWRITE=xxxxxx|(((
495 +(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:474px" %)
496 +|=(% style="width: 159px;" %)**Command Example**|=(% style="width: 227px;" %)**Function**|=(% style="width: 85px;" %)**Response**
497 +|(% style="width:159px" %)AT+RSWRITE=xxxxxx|(% style="width:227px" %)(((
489 489  Send command to 485 sensor
490 490  
491 491  Range : no more than 10 bytes
492 -)))|OK
501 +)))|(% style="width:85px" %)OK
493 493  
494 494  Eg: Send command **01 03 00 00 00 01 84 0A** to 485 sensor
495 495  
... ... @@ -508,12 +508,13 @@
508 508  
509 509  (% style="color:#037691" %)**AT Command:**
510 510  
511 -|**Command Example**|**Function**|**Response**
512 -|AT+DTR=1000|(((
520 +(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:433px" %)
521 +|=(% style="width: 157px;" %)**Command Example**|=(% style="width: 188px;" %)**Function**|=(% style="width: 85px;" %)**Response**
522 +|(% style="width:157px" %)AT+DTR=1000|(% style="width:188px" %)(((
513 513  Set response timeout to:
514 514  
515 515  Range : 0~~10000
516 -)))|OK
526 +)))|(% style="width:85px" %)OK
517 517  
518 518  (% style="color:#037691" %)**Downlink Command:**
519 519  
... ... @@ -530,45 +530,26 @@
530 530  
531 531  Feature: Set sensor in used. If there are 6 sensors, user can set to only send 5 sensors values.
532 532  
533 -See [[definition>>||anchor="H"]] for the sensor type.
543 +See [[definition>>||anchor="HWeatherSensorTypes:"]] for the sensor type.
534 534  
545 +[[image:image-20220624144904-12.png]]
535 535  
536 -|(% rowspan="2" %)Byte3|Bit23|Bit22|Bit21|Bit20|Bit19|Bit18|Bit17|Bit16
537 -| |A4|A3|A2|A1| | |
538 -|(% rowspan="2" %)Byte2|Bit15|Bit14|Bit13|Bit12|Bit11|Bit10|Bit9|Bit8
539 -| | |Solar Radiation|PAR|PM10|PM2.5|(((
540 -Rain
541 541  
542 -Gauge
543 -)))|(((
544 -Air
545 -
546 -Pressure
547 -)))
548 -|(% rowspan="2" %)Byte1|Bit7|Bit6|Bit5|Bit4|Bit3|Bit2|Bit1|Bit0
549 -|Humidity|Temperature|CO2|(((
550 -Rain/Snow
551 -
552 -Detect
553 -)))|illuminance|(((
554 -Wind
555 -
556 -Direction
557 -)))|Wind Speed|BAT
558 -
559 559  (% style="color:#037691" %)**AT Command:**
560 560  
561 -|**Command Example**|**Function**|**Response**
562 -|AT+STYPE=80221|Set sensor types|OK
550 +(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:377px" %)
551 +|=(% style="width: 157px;" %)**Command Example**|=(% style="width: 130px;" %)**Function**|=(% style="width: 87px;" %)**Response**
552 +|(% style="width:157px" %)AT+STYPE=80221|(% style="width:130px" %)Set sensor types|(% style="width:87px" %)OK
563 563  
564 564  Eg: The setting command **AT+STYPE=802212** means:
565 565  
566 -|(% rowspan="2" %)Byte3|Bit23|Bit22|Bit21|Bit20|Bit19|Bit18|Bit17|Bit16
567 -|0|0|0|0|1|0|0|0
568 -|(% rowspan="2" %)Byte2|Bit15|Bit14|Bit13|Bit12|Bit11|Bit10|Bit9|Bit8
569 -|0|0|0|0|0|0|1|0
570 -|(% rowspan="2" %)Byte1|Bit7|Bit6|Bit5|Bit4|Bit3|Bit2|Bit1|Bit0
571 -|0|0|1|0|0|0|0|1
556 +(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:495px" %)
557 +|(% rowspan="2" style="width:57px" %)Byte3|(% style="width:57px" %)Bit23|(% style="width:59px" %)Bit22|(% style="width:56px" %)Bit21|(% style="width:51px" %)Bit20|(% style="width:54px" %)Bit19|(% style="width:54px" %)Bit18|(% style="width:52px" %)Bit17|(% style="width:52px" %)Bit16
558 +|(% style="width:57px" %)0|(% style="width:59px" %)0|(% style="width:56px" %)0|(% style="width:51px" %)0|(% style="width:54px" %)1|(% style="width:54px" %)0|(% style="width:52px" %)0|(% style="width:52px" %)0
559 +|(% rowspan="2" style="width:57px" %)Byte2|(% style="width:57px" %)Bit15|(% style="width:59px" %)Bit14|(% style="width:56px" %)Bit13|(% style="width:51px" %)Bit12|(% style="width:54px" %)Bit11|(% style="width:54px" %)Bit10|(% style="width:52px" %)Bit9|(% style="width:52px" %)Bit8
560 +|(% style="width:57px" %)0|(% style="width:59px" %)0|(% style="width:56px" %)0|(% style="width:51px" %)0|(% style="width:54px" %)0|(% style="width:54px" %)0|(% style="width:52px" %)1|(% style="width:52px" %)0
561 +|(% rowspan="2" style="width:57px" %)Byte1|(% style="width:57px" %)Bit7|(% style="width:59px" %)Bit6|(% style="width:56px" %)Bit5|(% style="width:51px" %)Bit4|(% style="width:54px" %)Bit3|(% style="width:54px" %)Bit2|(% style="width:52px" %)Bit1|(% style="width:52px" %)Bit0
562 +|(% style="width:57px" %)0|(% style="width:59px" %)0|(% style="width:56px" %)1|(% style="width:51px" %)0|(% style="width:54px" %)0|(% style="width:54px" %)0|(% style="width:52px" %)0|(% style="width:52px" %)1
572 572  
573 573  So wsc1-L will upload the following data: Custom Sensor A1, Rain Gauge,CO2,BAT.
574 574  
... ... @@ -579,12 +579,11 @@
579 579  
580 580  (% style="color:red" %)**Note:**
581 581  
582 -~1. The sensor type will not be saved to flash, and the value will be updated every time the sensor is restarted or rescanned
573 +~1. The sensor type will not be saved to flash, and the value will be updated every time the sensor is restarted or rescanned.
583 583  
584 584  
585 585  
586 586  
587 -
588 588  = 4. Power consumption and battery =
589 589  
590 590  == 4.1 Total Power Consumption ==
... ... @@ -597,13 +597,15 @@
597 597  The main process unit WSC1-L is set to LoRaWAN Class C by default. If user want to reduce the power consumption of this unit, user can set it to run in Class A. In Class A mode, WSC1-L will not be to get real-time downlink command from IoT Server.
598 598  
599 599  
600 -
601 601  == 4.3 Battery ==
602 602  
603 -All sensors are only power by external power source. If external power source is off. All sensor won’t work.
592 +(((
593 +All sensors are only power by external power source. If external power source is off. All sensor won't work.
594 +)))
604 604  
605 -
596 +(((
606 606  Main Process Unit WSC1-L is powered by both external power source and internal 1000mAh rechargeable battery. If external power source is off, WSC1-L still runs and can send periodically uplinks, but the sensors value will become invalid.  External power source can recharge the 1000mAh rechargeable battery.
598 +)))
607 607  
608 608  
609 609  
... ... @@ -623,6 +623,8 @@
623 623  * IP Rating: IP65
624 624  * Support default sensors or 3rd party RS485 sensors
625 625  
618 +
619 +
626 626  == 5.2 Power Consumption ==
627 627  
628 628  WSC1-L (without external sensor): Idle: 4mA, Transmit: max 40mA
image-20220624144904-12.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +17.2 KB
Content