Summary

• Page properties (1 modified, 0 added, 0 removed)
• Attachments (0 modified, 0 added, 3 removed)
  • image-20220624142956-9.png
  • image-20220624143553-10.png
  • image-20220624143618-11.png

Details

Page properties

Content

...	...	@@ -67,6 +67,7 @@
67	67	* WSC1-L has an extra 1000mAh back up battery. So it can work even solar panel and storage battery Fails.
68	68	* Weather sensors won’t work if solar panel and storage battery fails.
69	69
	70	+
70	70	(% style="color:red" %)** Notice 2:**
71	71
72	72	Due to shipment and importation limitation, user is better to purchase below parts locally:
...	...	@@ -78,6 +78,7 @@
78	78	* Cabinet.
79	79
80	80
	82	+
81	81	== 2.2 How it works? ==
82	82
83	83	(((
...	...	@@ -96,6 +96,7 @@
96	96	1. User can send a downlink command to WSC1-L to do a re-scan on the available sensors.
97	97
98	98
	101	+
99	99	== 2.3 Example to use for LoRaWAN network ==
100	100
101	101	This section shows an example for how to join the TTN V3 LoRaWAN IoT server. Usages with other LoRaWAN IoT servers are of similar procedure.
...	...	@@ -152,6 +152,7 @@
152	152	* Valid Sensor Value: Use FPORT=2
153	153	* Other control command: Use FPORT other than 2.
154	154
	158	+
155	155	=== 2.4.1 Uplink FPORT~=5, Device Status ===
156	156
157	157	Uplink the device configures with FPORT=5. Once WSC1-L Joined the network, it will uplink this message to the server. After first uplink, WSC1-L will uplink Device Status every 12 hours
...	...	@@ -357,6 +357,7 @@
357	357	* AT Command Connection: See [[FAQ>>||anchor="H7.FAQ"]].
358	358	* LoRaWAN Downlink instruction for different platforms:  [[Use Note for Server>>doc:Main.WebHome]](IoT LoRaWAN Server)
359	359
	364	+
360	360	There are two kinds of commands to configure WSC1-L, they are:
361	361
362	362	* (% style="color:#4472c4" %)**General Commands**.
...	...	@@ -366,6 +366,7 @@
366	366	* General system settings like: uplink interval.
367	367	* LoRaWAN protocol & radio related command.
368	368
	374	+
369	369	They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack((% style="color:red" %)Note~*~*)(%%). These commands can be found on the wiki:  [[End Device Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
370	370
371	371	(% style="color:red" %)Note~*~*: Please check early user manual if you don’t have v1.8.0 firmware.
...	...	@@ -397,15 +397,18 @@
397	397
398	398
399	399
	406	+
400	400	== 3.2 Set Emergency Mode ==
401	401
402	402	Feature: In emergency mode, WSC1-L will uplink data every 1 minute.
403	403
	411	+
404	404	(% style="color:#037691" %)**AT Command:**
405	405
406		-[[image:image-20220624142956-9.png]]
	414	+|**Command Example**|**Function**|**Response**
	415	+|AT+ALARMMOD=1|Enter emergency mode. Uplink every 1 minute|OK
	416	+|AT+ALARMMOD=0|Exit emergency mode. Uplink base on TDC time|OK
407	407
408		-
409	409	(% style="color:#037691" %)**Downlink Command:**
410	410
411	411	* 0xE101     Same as: AT+ALARMMOD=1
...	...	@@ -414,6 +414,7 @@
414	414
415	415
416	416
	426	+
417	417	== 3.3 Add or Delete RS485 Sensor ==
418	418
419	419	Feature: User can add or delete 3^^rd^^ party sensor as long they are RS485/Modbus interface,baud rate support 9600.Maximum can add 4 sensors.
...	...	@@ -422,13 +422,13 @@
422	422
423	423	AT+DYSENSOR=Type_Code, Query_Length, Query_Command , Read_Length , Valid_Data ,has_CRC,timeout
424	424
425		-* Type_Code range:  A1 ~~ A4
426		-* Query_Length:  RS485 Query frame length, Value cannot be greater than 10
427		-* Query_Command:  RS485 Query frame data to be sent to sensor, cannot be larger than 10 bytes
428		-* Read_Length:  RS485 response frame length supposed to receive. Max can receive
429		-* Valid_Data:  valid data from RS485 Response, Valid Data will be added to Payload and upload via LoRaWAN.
430		-* has_CRC:  RS485 Response crc check  (0: no verification required 1: verification required). If CRC=1 and CRC error, valid data will be set to 0.
431		-* timeout:  RS485 receive timeout (uint:ms). Device will close receive window after timeout
	435	+* Type_Code range: A1 ~~ A4
	436	+* Query_Length: RS485 Query frame length, Value cannot be greater than 10
	437	+* Query_Command: RS485 Query frame data to be sent to sensor, cannot be larger than 10 bytes
	438	+* Read_Length: RS485 response frame length supposed to receive. Max can receive
	439	+* Valid_Data: valid data from RS485 Response, Valid Data will be added to Payload and upload via LoRaWAN.
	440	+* has_CRC: RS485 Response crc check  (0: no verification required 1: verification required). If CRC=1 and CRC error, valid data will be set to 0.
	441	+* timeout: RS485 receive timeout (uint:ms). Device will close receive window after timeout
432	432
433	433	Example:
434	434
...	...	@@ -486,6 +486,7 @@
486	486
487	487
488	488
	499	+
489	489	== 3.4 RS485 Test Command ==
490	490
491	491	(% style="color:#037691" %)**AT Command:**
...	...	@@ -509,6 +509,7 @@
509	509
510	510
511	511
	523	+
512	512	== 3.5 RS485 response timeout ==
513	513
514	514	Feature: Set or get extended time to receive 485 sensor data.
...	...	@@ -534,6 +534,7 @@
534	534
535	535
536	536
	549	+
537	537	== 3.6 Set Sensor Type ==
538	538
539	539	Feature: Set sensor in used. If there are 6 sensors, user can set to only send 5 sensors values.

image-20220624142956-9.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-9.2 KB

Content

image-20220624143553-10.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-6.7 KB

Content

image-20220624143618-11.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-6.3 KB

Content