Summary

• Page properties (1 modified, 0 added, 0 removed)
• Attachments (0 modified, 0 added, 2 removed)
  • image-20220624142619-8.png
  • image-20220624142956-9.png

Details

Page properties

Content

...	...	@@ -67,6 +67,7 @@
67	67	* WSC1-L has an extra 1000mAh back up battery. So it can work even solar panel and storage battery Fails.
68	68	* Weather sensors won’t work if solar panel and storage battery fails.
69	69
	70	+
70	70	(% style="color:red" %)** Notice 2:**
71	71
72	72	Due to shipment and importation limitation, user is better to purchase below parts locally:
...	...	@@ -152,6 +152,7 @@
152	152	* Valid Sensor Value: Use FPORT=2
153	153	* Other control command: Use FPORT other than 2.
154	154
	156	+
155	155	=== 2.4.1 Uplink FPORT~=5, Device Status ===
156	156
157	157	Uplink the device configures with FPORT=5. Once WSC1-L Joined the network, it will uplink this message to the server. After first uplink, WSC1-L will uplink Device Status every 12 hours
...	...	@@ -357,6 +357,7 @@
357	357	* AT Command Connection: See [[FAQ>>||anchor="H7.FAQ"]].
358	358	* LoRaWAN Downlink instruction for different platforms:  [[Use Note for Server>>doc:Main.WebHome]](IoT LoRaWAN Server)
359	359
	362	+
360	360	There are two kinds of commands to configure WSC1-L, they are:
361	361
362	362	* (% style="color:#4472c4" %)**General Commands**.
...	...	@@ -368,6 +368,8 @@
368	368
369	369	They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack((% style="color:red" %)Note~*~*)(%%). These commands can be found on the wiki:  [[End Device Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
370	370
	374	+[[http:~~/~~/wiki1.dragino.com/index.php?title=End_Device_Downlink_Command>>url:http://wiki.dragino.com/index.php?title=End_Device_Downlink_Command]]
	375	+
371	371	(% style="color:red" %)Note~*~*: Please check early user manual if you don’t have v1.8.0 firmware.
372	372
373	373
...	...	@@ -382,9 +382,20 @@
382	382
383	383	(% style="color:#037691" %)**AT Command: AT+TDC**
384	384
385		-[[image:image-20220624142619-8.png]]
	390	+|**Command Example**|**Function**|**Response**
	391	+|AT+TDC?|Show current transmit Interval|(((
	392	+30000
386	386
	394	+OK
387	387
	396	+the interval is 30000ms = 30s
	397	+)))
	398	+|AT+TDC=60000|Set Transmit Interval|(((
	399	+OK
	400	+
	401	+Set transmit interval to 60000ms = 60 seconds
	402	+)))
	403	+
388	388	(% style="color:#037691" %)**Downlink Command: 0x01**
389	389
390	390	Format: Command Code (0x01) followed by 3 bytes time value.
...	...	@@ -394,26 +394,22 @@
394	394	* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
395	395	* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
396	396
397		-
398		-
399		-
400	400	== 3.2 Set Emergency Mode ==
401	401
402	402	Feature: In emergency mode, WSC1-L will uplink data every 1 minute.
403	403
	417	+
404	404	(% style="color:#037691" %)**AT Command:**
405	405
406		-[[image:image-20220624142956-9.png]]
	420	+|**Command Example**|**Function**|**Response**
	421	+|AT+ALARMMOD=1|Enter emergency mode. Uplink every 1 minute|OK
	422	+|AT+ALARMMOD=0|Exit emergency mode. Uplink base on TDC time|OK
407	407
408		-
409	409	(% style="color:#037691" %)**Downlink Command:**
410	410
411	411	* 0xE101     Same as: AT+ALARMMOD=1
412	412	* 0xE100     Same as: AT+ALARMMOD=0
413	413
414		-
415		-
416		-
417	417	== 3.3 Add or Delete RS485 Sensor ==
418	418
419	419	Feature: User can add or delete 3^^rd^^ party sensor as long they are RS485/Modbus interface,baud rate support 9600.Maximum can add 4 sensors.
...	...	@@ -483,9 +483,6 @@
483	483
484	484	* 0xE5FF
485	485
486		-
487		-
488		-
489	489	== 3.4 RS485 Test Command ==
490	490
491	491	(% style="color:#037691" %)**AT Command:**
...	...	@@ -506,9 +506,6 @@
506	506
507	507	* 0xE20103000001840A     Same as: AT+RSWRITE=0103000001840A
508	508
509		-
510		-
511		-
512	512	== 3.5 RS485 response timeout ==
513	513
514	514	Feature: Set or get extended time to receive 485 sensor data.
...	...	@@ -531,9 +531,6 @@
531	531	* Example 1: Downlink Payload: E0000005 ~/~/ Set Transmit Interval (DTR) = 5 seconds
532	532	* Example 2: Downlink Payload: E000000A ~/~/ Set Transmit Interval (DTR) = 10 seconds
533	533
534		-
535		-
536		-
537	537	== 3.6 Set Sensor Type ==
538	538
539	539	Feature: Set sensor in used. If there are 6 sensors, user can set to only send 5 sensors values.

image-20220624142619-8.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-12.5 KB

Content

image-20220624142956-9.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-9.2 KB

Content