Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -67,6 +67,7 @@
67	67	* WSC1-L has an extra 1000mAh back up battery. So it can work even solar panel and storage battery Fails.
68	68	* Weather sensors won’t work if solar panel and storage battery fails.
69	69
	70	+
70	70	(% style="color:red" %)** Notice 2:**
71	71
72	72	Due to shipment and importation limitation, user is better to purchase below parts locally:
...	...	@@ -78,6 +78,7 @@
78	78	* Cabinet.
79	79
80	80
	82	+
81	81	== 2.2 How it works? ==
82	82
83	83	(((
...	...	@@ -96,6 +96,7 @@
96	96	1. User can send a downlink command to WSC1-L to do a re-scan on the available sensors.
97	97
98	98
	101	+
99	99	== 2.3 Example to use for LoRaWAN network ==
100	100
101	101	This section shows an example for how to join the TTN V3 LoRaWAN IoT server. Usages with other LoRaWAN IoT servers are of similar procedure.
...	...	@@ -152,6 +152,7 @@
152	152	* Valid Sensor Value: Use FPORT=2
153	153	* Other control command: Use FPORT other than 2.
154	154
	158	+
155	155	=== 2.4.1 Uplink FPORT~=5, Device Status ===
156	156
157	157	Uplink the device configures with FPORT=5. Once WSC1-L Joined the network, it will uplink this message to the server. After first uplink, WSC1-L will uplink Device Status every 12 hours
...	...	@@ -357,6 +357,7 @@
357	357	* AT Command Connection: See [[FAQ>>||anchor="H7.FAQ"]].
358	358	* LoRaWAN Downlink instruction for different platforms:  [[Use Note for Server>>doc:Main.WebHome]](IoT LoRaWAN Server)
359	359
	364	+
360	360	There are two kinds of commands to configure WSC1-L, they are:
361	361
362	362	* (% style="color:#4472c4" %)**General Commands**.
...	...	@@ -366,6 +366,7 @@
366	366	* General system settings like: uplink interval.
367	367	* LoRaWAN protocol & radio related command.
368	368
	374	+
369	369	They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack((% style="color:red" %)Note~*~*)(%%). These commands can be found on the wiki:  [[End Device Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
370	370
371	371	(% style="color:red" %)Note~*~*: Please check early user manual if you don’t have v1.8.0 firmware.
...	...	@@ -397,6 +397,7 @@
397	397
398	398
399	399
	406	+
400	400	== 3.2 Set Emergency Mode ==
401	401
402	402	Feature: In emergency mode, WSC1-L will uplink data every 1 minute.
...	...	@@ -416,6 +416,7 @@
416	416
417	417
418	418
	426	+
419	419	== 3.3 Add or Delete RS485 Sensor ==
420	420
421	421	Feature: User can add or delete 3^^rd^^ party sensor as long they are RS485/Modbus interface,baud rate support 9600.Maximum can add 4 sensors.
...	...	@@ -488,6 +488,7 @@
488	488
489	489
490	490
	499	+
491	491	== 3.4 RS485 Test Command ==
492	492
493	493	(% style="color:#037691" %)**AT Command:**
...	...	@@ -511,6 +511,7 @@
511	511
512	512
513	513
	523	+
514	514	== 3.5 RS485 response timeout ==
515	515
516	516	Feature: Set or get extended time to receive 485 sensor data.
...	...	@@ -536,6 +536,7 @@
536	536
537	537
538	538
	549	+
539	539	== 3.6 Set Sensor Type ==
540	540
541	541	Feature: Set sensor in used. If there are 6 sensors, user can set to only send 5 sensors values.