Summary

• Page properties (1 modified, 0 added, 0 removed)
• Attachments (0 modified, 1 added, 0 removed)
  • image-20220624142956-9.png

Details

Page properties

Content

...	...	@@ -67,7 +67,6 @@
67	67	* WSC1-L has an extra 1000mAh back up battery. So it can work even solar panel and storage battery Fails.
68	68	* Weather sensors won’t work if solar panel and storage battery fails.
69	69
70		-
71	71	(% style="color:red" %)** Notice 2:**
72	72
73	73	Due to shipment and importation limitation, user is better to purchase below parts locally:
...	...	@@ -79,7 +79,6 @@
79	79	* Cabinet.
80	80
81	81
82		-
83	83	== 2.2 How it works? ==
84	84
85	85	(((
...	...	@@ -98,7 +98,6 @@
98	98	1. User can send a downlink command to WSC1-L to do a re-scan on the available sensors.
99	99
100	100
101		-
102	102	== 2.3 Example to use for LoRaWAN network ==
103	103
104	104	This section shows an example for how to join the TTN V3 LoRaWAN IoT server. Usages with other LoRaWAN IoT servers are of similar procedure.
...	...	@@ -155,7 +155,6 @@
155	155	* Valid Sensor Value: Use FPORT=2
156	156	* Other control command: Use FPORT other than 2.
157	157
158		-
159	159	=== 2.4.1 Uplink FPORT~=5, Device Status ===
160	160
161	161	Uplink the device configures with FPORT=5. Once WSC1-L Joined the network, it will uplink this message to the server. After first uplink, WSC1-L will uplink Device Status every 12 hours
...	...	@@ -361,7 +361,6 @@
361	361	* AT Command Connection: See [[FAQ>>||anchor="H7.FAQ"]].
362	362	* LoRaWAN Downlink instruction for different platforms:  [[Use Note for Server>>doc:Main.WebHome]](IoT LoRaWAN Server)
363	363
364		-
365	365	There are two kinds of commands to configure WSC1-L, they are:
366	366
367	367	* (% style="color:#4472c4" %)**General Commands**.
...	...	@@ -371,7 +371,6 @@
371	371	* General system settings like: uplink interval.
372	372	* LoRaWAN protocol & radio related command.
373	373
374		-
375	375	They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack((% style="color:red" %)Note~*~*)(%%). These commands can be found on the wiki:  [[End Device Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
376	376
377	377	(% style="color:red" %)Note~*~*: Please check early user manual if you don’t have v1.8.0 firmware.
...	...	@@ -403,7 +403,6 @@
403	403
404	404
405	405
406		-
407	407	== 3.2 Set Emergency Mode ==
408	408
409	409	Feature: In emergency mode, WSC1-L will uplink data every 1 minute.
...	...	@@ -423,7 +423,6 @@
423	423
424	424
425	425
426		-
427	427	== 3.3 Add or Delete RS485 Sensor ==
428	428
429	429	Feature: User can add or delete 3^^rd^^ party sensor as long they are RS485/Modbus interface,baud rate support 9600.Maximum can add 4 sensors.
...	...	@@ -496,7 +496,6 @@
496	496
497	497
498	498
499		-
500	500	== 3.4 RS485 Test Command ==
501	501
502	502	(% style="color:#037691" %)**AT Command:**
...	...	@@ -520,7 +520,6 @@
520	520
521	521
522	522
523		-
524	524	== 3.5 RS485 response timeout ==
525	525
526	526	Feature: Set or get extended time to receive 485 sensor data.
...	...	@@ -546,7 +546,6 @@
546	546
547	547
548	548
549		-
550	550	== 3.6 Set Sensor Type ==
551	551
552	552	Feature: Set sensor in used. If there are 6 sensors, user can set to only send 5 sensors values.

image-20220624142956-9.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+9.2 KB

Content