Summary

• Page properties (1 modified, 0 added, 0 removed)
• Attachments (0 modified, 1 added, 0 removed)
  • image-20220624142619-8.png

Details

Page properties

Content

...	...	@@ -67,7 +67,6 @@
67	67	* WSC1-L has an extra 1000mAh back up battery. So it can work even solar panel and storage battery Fails.
68	68	* Weather sensors won’t work if solar panel and storage battery fails.
69	69
70		-
71	71	(% style="color:red" %)** Notice 2:**
72	72
73	73	Due to shipment and importation limitation, user is better to purchase below parts locally:
...	...	@@ -153,7 +153,6 @@
153	153	* Valid Sensor Value: Use FPORT=2
154	154	* Other control command: Use FPORT other than 2.
155	155
156		-
157	157	=== 2.4.1 Uplink FPORT~=5, Device Status ===
158	158
159	159	Uplink the device configures with FPORT=5. Once WSC1-L Joined the network, it will uplink this message to the server. After first uplink, WSC1-L will uplink Device Status every 12 hours
...	...	@@ -359,7 +359,6 @@
359	359	* AT Command Connection: See [[FAQ>>||anchor="H7.FAQ"]].
360	360	* LoRaWAN Downlink instruction for different platforms:  [[Use Note for Server>>doc:Main.WebHome]](IoT LoRaWAN Server)
361	361
362		-
363	363	There are two kinds of commands to configure WSC1-L, they are:
364	364
365	365	* (% style="color:#4472c4" %)**General Commands**.
...	...	@@ -371,7 +371,6 @@
371	371
372	372	They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack((% style="color:red" %)Note~*~*)(%%). These commands can be found on the wiki:  [[End Device Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
373	373
374		-
375	375	(% style="color:red" %)Note~*~*: Please check early user manual if you don’t have v1.8.0 firmware.
376	376
377	377
...	...	@@ -386,20 +386,9 @@
386	386
387	387	(% style="color:#037691" %)**AT Command: AT+TDC**
388	388
389		-|**Command Example**|**Function**|**Response**
390		-|AT+TDC?|Show current transmit Interval|(((
391		-30000
	385	+[[image:image-20220624142619-8.png]]
392	392
393		-OK
394	394
395		-the interval is 30000ms = 30s
396		-)))
397		-|AT+TDC=60000|Set Transmit Interval|(((
398		-OK
399		-
400		-Set transmit interval to 60000ms = 60 seconds
401		-)))
402		-
403	403	(% style="color:#037691" %)**Downlink Command: 0x01**
404	404
405	405	Format: Command Code (0x01) followed by 3 bytes time value.
...	...	@@ -409,6 +409,9 @@
409	409	* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
410	410	* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
411	411
	397	+
	398	+
	399	+
412	412	== 3.2 Set Emergency Mode ==
413	413
414	414	Feature: In emergency mode, WSC1-L will uplink data every 1 minute.
...	...	@@ -425,6 +425,9 @@
425	425	* 0xE101     Same as: AT+ALARMMOD=1
426	426	* 0xE100     Same as: AT+ALARMMOD=0
427	427
	416	+
	417	+
	418	+
428	428	== 3.3 Add or Delete RS485 Sensor ==
429	429
430	430	Feature: User can add or delete 3^^rd^^ party sensor as long they are RS485/Modbus interface,baud rate support 9600.Maximum can add 4 sensors.
...	...	@@ -494,6 +494,9 @@
494	494
495	495	* 0xE5FF
496	496
	488	+
	489	+
	490	+
497	497	== 3.4 RS485 Test Command ==
498	498
499	499	(% style="color:#037691" %)**AT Command:**
...	...	@@ -514,6 +514,9 @@
514	514
515	515	* 0xE20103000001840A     Same as: AT+RSWRITE=0103000001840A
516	516
	511	+
	512	+
	513	+
517	517	== 3.5 RS485 response timeout ==
518	518
519	519	Feature: Set or get extended time to receive 485 sensor data.
...	...	@@ -536,6 +536,9 @@
536	536	* Example 1: Downlink Payload: E0000005 ~/~/ Set Transmit Interval (DTR) = 5 seconds
537	537	* Example 2: Downlink Payload: E000000A ~/~/ Set Transmit Interval (DTR) = 10 seconds
538	538
	536	+
	537	+
	538	+
539	539	== 3.6 Set Sensor Type ==
540	540
541	541	Feature: Set sensor in used. If there are 6 sensors, user can set to only send 5 sensors values.

image-20220624142619-8.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+12.5 KB

Content