Changes for page WSC1-L-Dragino LoRaWAN Weather Station User Manual
Last modified by Xiaoling on 2025/05/07 14:00
Summary
-
Page properties (1 modified, 0 added, 0 removed)
-
Attachments (0 modified, 1 added, 0 removed)
Details
- Page properties
-
- Content
-
... ... @@ -79,6 +79,7 @@ 79 79 * Cabinet. 80 80 81 81 82 + 82 82 == 2.2 How it works? == 83 83 84 84 ((( ... ... @@ -97,6 +97,7 @@ 97 97 1. User can send a downlink command to WSC1-L to do a re-scan on the available sensors. 98 98 99 99 101 + 100 100 == 2.3 Example to use for LoRaWAN network == 101 101 102 102 This section shows an example for how to join the TTN V3 LoRaWAN IoT server. Usages with other LoRaWAN IoT servers are of similar procedure. ... ... @@ -369,9 +369,9 @@ 369 369 * General system settings like: uplink interval. 370 370 * LoRaWAN protocol & radio related command. 371 371 374 + 372 372 They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack((% style="color:red" %)Note~*~*)(%%). These commands can be found on the wiki: [[End Device Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]] 373 373 374 - 375 375 (% style="color:red" %)Note~*~*: Please check early user manual if you don’t have v1.8.0 firmware. 376 376 377 377 ... ... @@ -386,20 +386,9 @@ 386 386 387 387 (% style="color:#037691" %)**AT Command: AT+TDC** 388 388 389 -|**Command Example**|**Function**|**Response** 390 -|AT+TDC?|Show current transmit Interval|((( 391 -30000 391 +[[image:image-20220624142619-8.png]] 392 392 393 -OK 394 394 395 -the interval is 30000ms = 30s 396 -))) 397 -|AT+TDC=60000|Set Transmit Interval|((( 398 -OK 399 - 400 -Set transmit interval to 60000ms = 60 seconds 401 -))) 402 - 403 403 (% style="color:#037691" %)**Downlink Command: 0x01** 404 404 405 405 Format: Command Code (0x01) followed by 3 bytes time value. ... ... @@ -409,6 +409,10 @@ 409 409 * Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds 410 410 * Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds 411 411 403 + 404 + 405 + 406 + 412 412 == 3.2 Set Emergency Mode == 413 413 414 414 Feature: In emergency mode, WSC1-L will uplink data every 1 minute. ... ... @@ -425,6 +425,10 @@ 425 425 * 0xE101 Same as: AT+ALARMMOD=1 426 426 * 0xE100 Same as: AT+ALARMMOD=0 427 427 423 + 424 + 425 + 426 + 428 428 == 3.3 Add or Delete RS485 Sensor == 429 429 430 430 Feature: User can add or delete 3^^rd^^ party sensor as long they are RS485/Modbus interface,baud rate support 9600.Maximum can add 4 sensors. ... ... @@ -494,6 +494,10 @@ 494 494 495 495 * 0xE5FF 496 496 496 + 497 + 498 + 499 + 497 497 == 3.4 RS485 Test Command == 498 498 499 499 (% style="color:#037691" %)**AT Command:** ... ... @@ -514,6 +514,10 @@ 514 514 515 515 * 0xE20103000001840A Same as: AT+RSWRITE=0103000001840A 516 516 520 + 521 + 522 + 523 + 517 517 == 3.5 RS485 response timeout == 518 518 519 519 Feature: Set or get extended time to receive 485 sensor data. ... ... @@ -536,6 +536,10 @@ 536 536 * Example 1: Downlink Payload: E0000005 ~/~/ Set Transmit Interval (DTR) = 5 seconds 537 537 * Example 2: Downlink Payload: E000000A ~/~/ Set Transmit Interval (DTR) = 10 seconds 538 538 546 + 547 + 548 + 549 + 539 539 == 3.6 Set Sensor Type == 540 540 541 541 Feature: Set sensor in used. If there are 6 sensors, user can set to only send 5 sensors values.
- image-20220624142619-8.png
-
- Author
-
... ... @@ -1,0 +1,1 @@ 1 +XWiki.Xiaoling - Size
-
... ... @@ -1,0 +1,1 @@ 1 +12.5 KB - Content