<
From version < 27.5 >
edited by Xiaoling
on 2022/06/24 14:19
To version < 28.4 >
edited by Xiaoling
on 2022/06/24 14:28
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -67,7 +67,6 @@
67 67  * WSC1-L has an extra 1000mAh back up battery. So it can work even solar panel and storage battery Fails.
68 68  * Weather sensors won’t work if solar panel and storage battery fails.
69 69  
70 -
71 71  (% style="color:red" %)** Notice 2:**
72 72  
73 73  Due to shipment and importation limitation, user is better to purchase below parts locally:
... ... @@ -153,7 +153,6 @@
153 153  * Valid Sensor Value: Use FPORT=2
154 154  * Other control command: Use FPORT other than 2.
155 155  
156 -
157 157  === 2.4.1 Uplink FPORT~=5, Device Status ===
158 158  
159 159  Uplink the device configures with FPORT=5. Once WSC1-L Joined the network, it will uplink this message to the server. After first uplink, WSC1-L will uplink Device Status every 12 hours
... ... @@ -359,7 +359,6 @@
359 359  * AT Command Connection: See [[FAQ>>||anchor="H7.FAQ"]].
360 360  * LoRaWAN Downlink instruction for different platforms:  [[Use Note for Server>>doc:Main.WebHome]](IoT LoRaWAN Server)
361 361  
362 -
363 363  There are two kinds of commands to configure WSC1-L, they are:
364 364  
365 365  * (% style="color:#4472c4" %)**General Commands**.
... ... @@ -371,8 +371,6 @@
371 371  
372 372  They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack((% style="color:red" %)Note~*~*)(%%). These commands can be found on the wiki:  [[End Device Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
373 373  
374 -[[http:~~/~~/wiki1.dragino.com/index.php?title=End_Device_Downlink_Command>>url:http://wiki.dragino.com/index.php?title=End_Device_Downlink_Command]]
375 -
376 376  (% style="color:red" %)Note~*~*: Please check early user manual if you don’t have v1.8.0 firmware.
377 377  
378 378  
... ... @@ -387,20 +387,9 @@
387 387  
388 388  (% style="color:#037691" %)**AT Command: AT+TDC**
389 389  
390 -|**Command Example**|**Function**|**Response**
391 -|AT+TDC?|Show current transmit Interval|(((
392 -30000
385 +[[image:image-20220624142619-8.png]]
393 393  
394 -OK
395 395  
396 -the interval is 30000ms = 30s
397 -)))
398 -|AT+TDC=60000|Set Transmit Interval|(((
399 -OK
400 -
401 -Set transmit interval to 60000ms = 60 seconds
402 -)))
403 -
404 404  (% style="color:#037691" %)**Downlink Command: 0x01**
405 405  
406 406  Format: Command Code (0x01) followed by 3 bytes time value.
... ... @@ -410,6 +410,9 @@
410 410  * Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
411 411  * Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
412 412  
397 +
398 +
399 +
413 413  == 3.2 Set Emergency Mode ==
414 414  
415 415  Feature: In emergency mode, WSC1-L will uplink data every 1 minute.
... ... @@ -426,6 +426,9 @@
426 426  * 0xE101     Same as: AT+ALARMMOD=1
427 427  * 0xE100     Same as: AT+ALARMMOD=0
428 428  
416 +
417 +
418 +
429 429  == 3.3 Add or Delete RS485 Sensor ==
430 430  
431 431  Feature: User can add or delete 3^^rd^^ party sensor as long they are RS485/Modbus interface,baud rate support 9600.Maximum can add 4 sensors.
... ... @@ -495,6 +495,9 @@
495 495  
496 496  * 0xE5FF  
497 497  
488 +
489 +
490 +
498 498  == 3.4 RS485 Test Command ==
499 499  
500 500  (% style="color:#037691" %)**AT Command:**
... ... @@ -515,6 +515,9 @@
515 515  
516 516  * 0xE20103000001840A     Same as: AT+RSWRITE=0103000001840A
517 517  
511 +
512 +
513 +
518 518  == 3.5 RS485 response timeout ==
519 519  
520 520  Feature: Set or get extended time to receive 485 sensor data.
... ... @@ -537,6 +537,9 @@
537 537  * Example 1: Downlink Payload: E0000005 ~/~/ Set Transmit Interval (DTR) = 5 seconds
538 538  * Example 2: Downlink Payload: E000000A ~/~/ Set Transmit Interval (DTR) = 10 seconds
539 539  
536 +
537 +
538 +
540 540  == 3.6 Set Sensor Type ==
541 541  
542 542  Feature: Set sensor in used. If there are 6 sensors, user can set to only send 5 sensors values.
image-20220624142619-8.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +12.5 KB
Content
Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0