Skip to Content
Last modified by Mengting Qiu on 2025/06/10 18:53
From version 27.4
edited by Xiaoling
on 2022/06/24 14:16
Change comment: There is no comment for this version
To version 28.2
edited by Xiaoling
on 2022/06/24 14:27
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -68,7 +68,6 @@
68 68  * Weather sensors won’t work if solar panel and storage battery fails.
69 69  
70 70  
71 -
72 72  (% style="color:red" %)** Notice 2:**
73 73  
74 74  Due to shipment and importation limitation, user is better to purchase below parts locally:
... ... @@ -157,7 +157,6 @@
157 157  * Other control command: Use FPORT other than 2.
158 158  
159 159  
160 -
161 161  === 2.4.1 Uplink FPORT~=5, Device Status ===
162 162  
163 163  Uplink the device configures with FPORT=5. Once WSC1-L Joined the network, it will uplink this message to the server. After first uplink, WSC1-L will uplink Device Status every 12 hours
... ... @@ -364,7 +364,6 @@
364 364  * LoRaWAN Downlink instruction for different platforms:  [[Use Note for Server>>doc:Main.WebHome]](IoT LoRaWAN Server)
365 365  
366 366  
367 -
368 368  There are two kinds of commands to configure WSC1-L, they are:
369 369  
370 370  * (% style="color:#4472c4" %)**General Commands**.
... ... @@ -374,9 +374,8 @@
374 374  * General system settings like: uplink interval.
375 375  * LoRaWAN protocol & radio related command.
376 376  
377 -They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack((% style="color:red" %)Note~*~*)(%%). These commands can be found on the wiki:
378 378  
379 -[[http:~~/~~/wiki.dragino.com/index.php?title=End_Device_Downlink_Command>>url:http://wiki.dragino.com/index.php?title=End_Device_Downlink_Command]]
375 +They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack((% style="color:red" %)Note~*~*)(%%). These commands can be found on the wiki:  [[End Device Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
380 380  
381 381  (% style="color:red" %)Note~*~*: Please check early user manual if you don’t have v1.8.0 firmware.
382 382  
... ... @@ -392,20 +392,9 @@
392 392  
393 393  (% style="color:#037691" %)**AT Command: AT+TDC**
394 394  
395 -|**Command Example**|**Function**|**Response**
396 -|AT+TDC?|Show current transmit Interval|(((
397 -30000
391 +[[image:image-20220624142619-8.png]]
398 398  
399 -OK
400 400  
401 -the interval is 30000ms = 30s
402 -)))
403 -|AT+TDC=60000|Set Transmit Interval|(((
404 -OK
405 -
406 -Set transmit interval to 60000ms = 60 seconds
407 -)))
408 -
409 409  (% style="color:#037691" %)**Downlink Command: 0x01**
410 410  
411 411  Format: Command Code (0x01) followed by 3 bytes time value.
... ... @@ -415,6 +415,10 @@
415 415  * Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
416 416  * Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
417 417  
403 +
404 +
405 +
406 +
418 418  == 3.2 Set Emergency Mode ==
419 419  
420 420  Feature: In emergency mode, WSC1-L will uplink data every 1 minute.
... ... @@ -431,6 +431,10 @@
431 431  * 0xE101     Same as: AT+ALARMMOD=1
432 432  * 0xE100     Same as: AT+ALARMMOD=0
433 433  
423 +
424 +
425 +
426 +
434 434  == 3.3 Add or Delete RS485 Sensor ==
435 435  
436 436  Feature: User can add or delete 3^^rd^^ party sensor as long they are RS485/Modbus interface,baud rate support 9600.Maximum can add 4 sensors.
... ... @@ -500,6 +500,10 @@
500 500  
501 501  * 0xE5FF  
502 502  
496 +
497 +
498 +
499 +
503 503  == 3.4 RS485 Test Command ==
504 504  
505 505  (% style="color:#037691" %)**AT Command:**
... ... @@ -520,6 +520,10 @@
520 520  
521 521  * 0xE20103000001840A     Same as: AT+RSWRITE=0103000001840A
522 522  
520 +
521 +
522 +
523 +
523 523  == 3.5 RS485 response timeout ==
524 524  
525 525  Feature: Set or get extended time to receive 485 sensor data.
image-20220624142619-8.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +12.5 KB
Content