WSC1-L-Dragino LoRaWAN Weather Station User Manual

Dragino LoRaWAN weather station series products are designed for measuring atmospheric conditions to provide information for weather forecasts and to study the (% style="color:#4472c4" %)**weather and climate**(%%). They consist of a (% style="color:#4472c4" %)**main process device (WSC1-L) and various sensors**.

25

)))

26

27

(((

28

The sensors include various type such as: (% style="color:#4472c4" %)**Rain Gauge**, **Temperature/Humidity/Pressure sensor**, **Wind Speed/direction sensor**, **Illumination sensor**, **CO2 sensor**, **Rain/Snow sensor**,** PM2.5/10 sensor**, **PAR(Photosynthetically Available Radiation) sensor, Total Solar Radiation sensor**(%%) and so on.

)))

(((

Main process device WSC1-L is an outdoor LoRaWAN RS485 end node. It is powered by external (% style="color:#4472c4" %)**12v solar power**(%%) and have a (% style="color:#4472c4" %)**built-in li-on backup battery**(%%). WSC1-L reads value from various sensors and upload these sensor data to IoT server via LoRaWAN wireless protocol.

)))

(((

WSC1-L is full compatible with(% style="color:#4472c4" %)** LoRaWAN Class C protocol**(%%), it can work with standard LoRaWAN gateway.

)))

= 2. How to use =

== 2.1 Installation ==

44

45

Below is an installation example for the weather station. Field installation example can be found at [[Appendix I: Field Installation Photo.>>||anchor="H11.AppendixI:FieldInstallationPhoto"]]

46

47

[[image:1656041948552-849.png]]

48

49

50

(% style="color:blue" %)** Wiring:**

51

52

~1. WSC1-L and sensors all powered by solar power via MPPT

53

54

2. WSC1-L and sensors connect to each other via RS485/Modbus.

55

56

3. WSC1-L read value from each sensor and send uplink via LoRaWAN

57

58

59

WSC1-L is shipped with a RS485 converter board, for the easy connection to different sensors and WSC1-L. Below is a connection photo:

60

61

[[image:1656042136605-251.png]]

62

63

64

(% style="color:red" %)**Notice 1:**

65

66

* All weather sensors and WSC1-L are powered by MPPT solar recharge controller. MPPT is connected to solar panel and storage battery.

67

* WSC1-L has an extra 1000mAh back up battery. So it can work even solar panel and storage battery Fails.

68

* Weather sensors won’t work if solar panel and storage battery fails.

69

70

(% style="color:red" %)**Notice 2:**

71

72

Due to shipment and importation limitation, user is better to purchase below parts locally:

* Solar Panel

* Storage Battery

* MPPT Solar Recharger

77

* Mounting Kit includes pole and mast assembly. Each weather sensor has it's own mounting assembly, user can check the sensor section in this manual.

78

* Cabinet.

79

80

== 2.2 How it works? ==

81

82

(((

83

Each WSC1-L is shipped with a worldwide unique set of OTAA keys. To use WSC1-L in a LoRaWAN network, user needs to input the OTAA keys in LoRaWAN network server. After finish installation as above. Create WSC1-L in your LoRaWAN server and Power on WSC1-L , it can join the LoRaWAN network and start to transmit sensor data. The default period for each uplink is 20 minutes.

)))

(((

Open WSC1-L and put the yellow jumper as below position to power on WSC1-L.

89

)))

90

91

[[image:1656042192857-709.png]]

92

93

94

(% style="color:red" %)**Notice:**

95

96

1. WSC1-L will auto scan available weather sensors when power on or reboot.

97

1. User can send a [[downlink command>>||anchor="H3.ConfigureWSC1-LviaATCommandorLoRaWANDownlink"]] to WSC1-L to do a re-scan on the available sensors.

== 2.3 Example to use for LoRaWAN network ==

102

103

This section shows an example for how to join the TTN V3 LoRaWAN IoT server. Usages with other LoRaWAN IoT servers are of similar procedure.

104

105

106

[[image:1656042612899-422.png]]

Assume the DLOS8 is already set to connect to [[TTN V3 network >>url:https://eu1.cloud.thethings.network/]]. We need to add the WSC1-L device in TTN V3:

111

112

113

(% style="color:blue" %)**Step 1**(%%): Create a device in TTN V3 with the OTAA keys from WSC1-L.

114

115

Each WSC1-L is shipped with a sticker with the default device EUI as below:

116

117

[[image:image-20220624115043-1.jpeg]]

118

119

120

User can enter these keys in the LoRaWAN Server portal. Below is TTN V3 screen shot:

121

122

**Add APP EUI in the application.**

123

124

[[image:1656042662694-311.png]]

125

126

[[image:1656042673910-429.png]]

**Choose Manually to add WSC1-L**

132

133

[[image:1656042695755-103.png]]

**Add APP KEY and DEV EUI**

138

139

[[image:1656042723199-746.png]]

(((

(% style="color:blue" %)**Step 2**(%%): Power on WSC1-L, it will start to join TTN server. After join success, it will start to upload sensor data to TTN V3 and user can see in the panel.

)))

[[image:1656042745346-283.png]]

== 2.4 Uplink Payload ==

153

154

Uplink payloads include two types: Valid Sensor Value and other status / control command.

155

156

* Valid Sensor Value: Use FPORT=2

157

* Other control command: Use FPORT other than 2.

=== 2.4.1 Uplink FPORT~=5, Device Status ===

163

164

Uplink the device configures with FPORT=5. Once WSC1-L Joined the network, it will uplink this message to the server. After first uplink, WSC1-L will uplink Device Status every 12 hours

(((

User can also use downlink command(0x2301) to ask WSC1-L to resend this uplink

169

)))

170

171

(% border="1" cellspacing="8" style="background-color:#ffffcc; color:green; width:500px" %)

172

173

|(% style="width:99px" %)**Value**|(% style="width:112px" %)[[Sensor Model>>||anchor="HSensorModel:"]]|(% style="width:135px" %)[[Firmware Version>>||anchor="HFirmwareVersion:"]]|(% style="width:126px" %)[[Frequency Band>>||anchor="HFrequencyBand:"]]|(% style="width:85px" %)[[Sub-band>>||anchor="HSub-Band:"]]|(% style="width:46px" %)[[BAT>>||anchor="HBAT:"]]|(% style="width:166px" %)[[Weather Sensor Types>>||anchor="HWeatherSensorTypes:"]]

174

175

[[image:1656043061044-343.png]]

176

177

178

Example Payload (FPort=5): [[image:image-20220624101005-1.png]]

==== (% style="color:#037691" %)**Sensor Model:**(%%) ====

183

184

For WSC1-L, this value is 0x0D.

==== (% style="color:#037691" %)**Firmware Version:**(%%) ====

189

190

0x0100, Means: v1.0.0 version.

==== (% style="color:#037691" %)**Frequency Band:**(%%) ====

*0x01: EU868

*0x02: US915

*0x03: IN865

*0x04: AU915

*0x05: KZ865

*0x06: RU864

*0x07: AS923

*0x08: AS923-1

*0x09: AS923-2

*0x0a: AS923-3

==== (% style="color:#037691" %)**Sub-Band:**(%%) ====

219

220

value 0x00 ~~ 0x08(only for CN470, AU915,US915. Others are0x00)

==== (% style="color:#037691" %)**BAT:**(%%) ====

225

226

(((

227

shows the battery voltage for WSC1-L MCU.

)))

(((

Ex1: 0x0BD6/1000 = 3.03 V

)))

==== (% style="color:#037691" %)**Weather Sensor Types:**(%%) ====

237

238

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:100px" %)

239

|Byte3|Byte2|Byte1

240

241

Bit = 1 means this sensor is connected, Bit=0 means this sensor is not connected

242

243

[[image:image-20220624134713-1.png]]

244

245

246

Eg: 0x1000FE = 1 0000 0000 0000 1111 1110(b)

247

248

External sensors detected by WSC1-L include :

custom sensor A1,

PAR sensor (WSS-07),

Total Solar Radiation sensor (WSS-06),

255

256

CO2/PM2.5/PM10 (WSS-03),

257

258

Wind Speed/Direction (WSS-02)

259

260

261

User can also use downlink command(0x26 01) to ask WSC1-L to resend this uplink :

262

263

(% style="color:#037691" %)**Downlink:0x26 01**

264

265

[[image:1656049673488-415.png]]

=== 2.4.2 Uplink FPORT~=2, Real time sensor value ===

270

271

(((

272

WSC1-L will send this uplink after Device Config uplink once join LoRaWAN network successfully. And it will periodically send this uplink. Default interval is 20 minutes and [[can be changed>>||anchor="H3.1SetTransmitIntervalTime"]].

)))

(((

Uplink uses FPORT=2 and every 20 minutes send one uplink by default.

)))

(((

The upload length is dynamic, depends on what type of weather sensors are connected. The uplink payload is combined with sensor segments. As below:

)))

(% style="color:#4472c4" %)** Uplink Payload**:

286

287

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:464px" %)

288

|(% style="width:140px" %)Sensor Segment 1|(% style="width:139px" %)Sensor Segment 2|(% style="width:42px" %)……|(% style="width:140px" %)Sensor Segment n

289

290

(% style="color:#4472c4" %)** Sensor Segment Define**:

291

292

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:330px" %)

293

|(% style="width:89px" %)Type Code|(% style="width:114px" %)Length (Bytes)|(% style="width:124px" %)Measured Value

294

295

(% style="color:#4472c4" %)**Sensor Type Table:**

296

297

[[image:image-20220706154434-1.png]]

(((

Below is an example payload: [[image:image-20220624140615-3.png]]

)))

(((

)))

(((

When sending this payload to LoRaWAN server. WSC1-L will send this in one uplink or several uplinks according to LoRaWAN spec requirement. For example, total length of Payload is 54 bytes.

)))

* (((

When WSC1-L sending in US915 frequency DR0 data rate. Because this data rate has limitation of 11 bytes payload for each uplink. The payload will be split into below packets and uplink.

)))

(((

Uplink 1: [[image:image-20220624140735-4.png]]

)))

(((

)))

(((

Uplink 2: [[image:image-20220624140842-5.png]]

)))

(((

)))

* (((

When WSC1-L sending in EU868 frequency DR0 data rate. The payload will be split into below packets and uplink:

)))

(((

Uplink 1: [[image:image-20220624141025-6.png]]

)))

(((

)))

Uplink 2: [[image:image-20220624141100-7.png]]

=== 2.4.3 Decoder in TTN V3 ===

349

350

(((

351

In LoRaWAN platform, user only see HEX payload by default, user needs to use payload formatters to decode the payload to see human-readable value.

)))

(((

)))

(((

Download decoder for suitable platform from:

)))

(((

[[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Weather_Station/WSC1-L/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Weather_Station/WSC1-L/]]

)))

(((

and put as below:

)))

[[image:1656051152438-578.png]]

== 2.5 Show data on Application Server ==

375

376

(((

377

Application platform provides a human friendly interface to show the sensor data, once we have sensor data in TTN V3, we can use Datacake to connect to TTN V3 and see the data in Datacake. Below are the steps:

)))

(((

)))

(((

(% style="color:blue" %)**Step 1**(%%): Be sure that your device is programmed and properly connected to the LoRaWAN network.

)))

(((

(% style="color:blue" %)**Step 2**(%%): Configure your Application to forward data to Datacake you will need to add integration. Go to TTN V3 Console ~-~-> Applications ~-~-> Integrations ~-~-> Add Integrations.

390

)))

391

392

[[image:1656051197172-131.png]]

**Add TagoIO:**

[[image:1656051223585-631.png]]

**Authorization:**

[[image:1656051248318-368.png]]

403

404

405

In TagoIO console ([[https:~~/~~/admin.tago.io~~/~~/>>url:https://datacake.co/]]) , add WSC1-L:

406

407

[[image:1656051277767-168.png]]

= 3. Configure WSC1-L via AT Command or LoRaWAN Downlink =

412

413

Use can configure WSC1-L via AT Command or LoRaWAN Downlink.

414

415

* AT Command Connection: See [[FAQ>>||anchor="H7.FAQ"]].

416

* LoRaWAN Downlink instruction for different platforms: [[Use Note for Server>>doc:Main.WebHome]](IoT LoRaWAN Server)

417

418

There are two kinds of commands to configure WSC1-L, they are:

419

420

* (% style="color:#4472c4" %)**General Commands**.

421

422

These commands are to configure:

423

424

* General system settings like: uplink interval.

425

* LoRaWAN protocol & radio related command.

426

427

They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack((% style="color:red" %)Note~*~*)(%%). These commands can be found on the wiki: [[End Device Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]

428

429

(% style="color:red" %)Note~*~*: Please check early user manual if you don’t have v1.8.0 firmware.

430

431

432

* (% style="color:#4472c4" %)**Commands special design for WSC1-L**

433

434

These commands only valid for WSC1-L, as below:

== 3.1 Set Transmit Interval Time ==

439

440

Feature: Change LoRaWAN End Node Transmit Interval.

441

442

(% style="color:#037691" %)**AT Command: AT+TDC**

443

444

[[image:image-20220624142619-8.png]]

445

446

447

(% style="color:#037691" %)**Downlink Command: 0x01**

448

449

Format: Command Code (0x01) followed by 3 bytes time value.

450

451

If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.

452

453

* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds

454

* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds

== 3.2 Set Emergency Mode ==

460

461

Feature: In emergency mode, WSC1-L will uplink data every 1 minute.

462

463

(% style="color:#037691" %)**AT Command:**

464

465

[[image:image-20220624142956-9.png]]

466

467

468

(% style="color:#037691" %)**Downlink Command:**

469

470

* 0xE101 Same as: AT+ALARMMOD=1

471

* 0xE100 Same as: AT+ALARMMOD=0

== 3.3 Add or Delete RS485 Sensor ==

477

478

(((

479

Feature: User can add or delete 3^^rd^^ party sensor as long they are RS485/Modbus interface,baud rate support 9600.Maximum can add 4 sensors.

)))

(((

(% style="color:#037691" %)**AT Command: **

)))

(((

(% style="color:blue" %)**AT+DYSENSOR=Type_Code, Query_Length, Query_Command , Read_Length , Valid_Data ,has_CRC,timeout**

)))

* (((

Type_Code range: A1 ~~ A4

492

)))

493

* (((

494

Query_Length: RS485 Query frame length, Value cannot be greater than 10

495

)))

496

* (((

497

Query_Command: RS485 Query frame data to be sent to sensor, cannot be larger than 10 bytes

498

)))

499

* (((

500

Read_Length: RS485 response frame length supposed to receive. Max can receive

501

)))

502

* (((

503

Valid_Data: valid data from RS485 Response, Valid Data will be added to Payload and upload via LoRaWAN.

504

)))

505

* (((

506

has_CRC: RS485 Response crc check (0: no verification required 1: verification required). If CRC=1 and CRC error, valid data will be set to 0.

507

)))

508

* (((

509

timeout: RS485 receive timeout (uint:ms). Device will close receive window after timeout

)))

(((

**Example:**

)))

(((

User need to change external sensor use the type code as address code.

)))

(((

With a 485 sensor, after correctly changing the address code to A1, the RS485 query frame is shown in the following table:

522

)))

523

524

[[image:image-20220624143553-10.png]]

525

526

527

The response frame of the sensor is as follows:

528

529

[[image:image-20220624143618-11.png]]

**Then the following parameters should be:**

534

535

* Address_Code range: A1

536

* Query_Length: 8

537

* Query_Command: A103000000019CAA

538

* Read_Length: 8

539

* Valid_Data: 24 (Indicates that the data length is 2 bytes, starting from the 4th byte)

540

* has_CRC: 1

541

* timeout: 1500 (Fill in the test according to the actual situation)

542

543

**So the input command is:**

544

545

AT+DYSENSOR=A1,8,A103000000019CAA,8,24,1,1500

546

547

548

In every sampling. WSC1-L will auto append the sensor segment as per this structure and uplink.

549

550

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:351px" %)

551

|=(% style="width: 94px;" %)Type Code|=(% style="width: 121px;" %)Length (Bytes)|=(% style="width: 132px;" %)Measured Value

552

|(% style="width:94px" %)A1|(% style="width:121px" %)2|(% style="width:132px" %)0x000A

553

554

**Related commands:**

555

556

AT+DYSENSOR=A1,0 ~-~-> Delete 3^^rd^^ party sensor A1.

557

558

AT+DYSENSOR ~-~-> List All 3^^rd^^ Party Sensor. Like below:

559

560

561

(% style="color:#037691" %)**Downlink Command: **

562

563

**delete custom sensor A1:**

564

565

* 0xE5A1 Same as: AT+DYSENSOR=A1,0

566

567

**Remove all custom sensors**

* 0xE5FF

== 3.4 RS485 Test Command ==

575

576

(% style="color:#037691" %)**AT Command:**

577

578

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:474px" %)

579

|=(% style="width: 159px;" %)**Command Example**|=(% style="width: 227px;" %)**Function**|=(% style="width: 85px;" %)**Response**

580

|(% style="width:159px" %)AT+RSWRITE=xxxxxx|(% style="width:227px" %)(((

581

(((

582

Send command to 485 sensor

)))

(((

Range : no more than 10 bytes

587

)))

588

)))|(% style="width:85px" %)OK

589

590

Eg: Send command **01 03 00 00 00 01 84 0A** to 485 sensor

591

592

AT+RSWRITE=0103000001840A

593

594

595

(% style="color:#037691" %)**Downlink Command:**

596

597

* 0xE20103000001840A Same as: AT+RSWRITE=0103000001840A

598

599

== 3.5 RS485 response timeout ==

600

601

Feature: Set or get extended time to receive 485 sensor data.

602

603

(% style="color:#037691" %)**AT Command:**

604

605

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:433px" %)

606

|=(% style="width: 157px;" %)**Command Example**|=(% style="width: 188px;" %)**Function**|=(% style="width: 85px;" %)**Response**

607

|(% style="width:157px" %)AT+DTR=1000|(% style="width:188px" %)(((

608

(((

609

Set response timeout to:

)))

(((

Range : 0~~10000

)))

)))|(% style="width:85px" %)OK

616

617

(% style="color:#037691" %)**Downlink Command:**

618

619

Format: Command Code (0xE0) followed by 3 bytes time value.

620

621

If the downlink payload=E0000005, it means set the END Node’s Transmit Interval to 0x000005=5(S), while type code is E0.

622

623

* Example 1: Downlink Payload: E0000005 ~/~/ Set Transmit Interval (DTR) = 5 seconds

624

* Example 2: Downlink Payload: E000000A ~/~/ Set Transmit Interval (DTR) = 10 seconds

625

626

== 3.6 Set Sensor Type ==

627

628

(((

629

Feature: Set sensor in used. If there are 6 sensors, user can set to only send 5 sensors values.

)))

(((

See [[definition>>||anchor="HWeatherSensorTypes:"]] for the sensor type.

634

)))

635

636

[[image:image-20220624144904-12.png]]

637

638

639

(% style="color:#037691" %)**AT Command:**

640

641

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:377px" %)

642

|=(% style="width: 157px;" %)**Command Example**|=(% style="width: 130px;" %)**Function**|=(% style="width: 87px;" %)**Response**

643

|(% style="width:157px" %)AT+STYPE=80221|(% style="width:130px" %)Set sensor types|(% style="width:87px" %)OK

644

645

Eg: The setting command **AT+STYPE=802212** means:

646

647

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:495px" %)

So wsc1-L will upload the following data: Custom Sensor A1, Rain Gauge,CO2,BAT.

656

657

658

(% style="color:#037691" %)**Downlink Command:**

659

660

* 0xE400802212 Same as: AT+STYPE=80221

661

662

(% style="color:red" %)**Note:**

663

664

~1. The sensor type will not be saved to flash, and the value will be updated every time the sensor is restarted or rescanned.

= 4. Power consumption and battery =

669

670

== 4.1 Total Power Consumption ==

671

672

Dragino Weather Station serial products include the main process unit ( WSC1-L ) and various sensors. The total power consumption equal total power of all above units. The power consumption for main process unit WSC1-L is 18ma @ 12v. and the power consumption of each sensor can be found on the Sensors chapter.

673

674

675

== 4.2 Reduce power consumption ==

676

677

The main process unit WSC1-L is set to LoRaWAN Class C by default. If user want to reduce the power consumption of this unit, user can set it to run in Class A. In Class A mode, WSC1-L will not be to get real-time downlink command from IoT Server.

== 4.3 Battery ==

(((

All sensors are only power by external power source. If external power source is off. All sensor won't work.

)))

(((

Main Process Unit WSC1-L is powered by both external power source and internal 1000mAh rechargeable battery. If external power source is off, WSC1-L still runs and can send periodically uplinks, but the sensors value will become invalid. External power source can recharge the 1000mAh rechargeable battery.

)))

= 5. Main Process Unit WSC1-L =

== 5.1 Features ==

* Wall Attachable.

* LoRaWAN v1.0.3 Class A protocol.

697

* RS485 / Modbus protocol

698

* Frequency Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915

699

* AT Commands to change parameters

700

* Remote configure parameters via LoRaWAN Downlink

701

* Firmware upgradable via program port

702

* Powered by external 12v battery

703

* Back up rechargeable 1000mAh battery

704

* IP Rating: IP65

705

* Support default sensors or 3rd party RS485 sensors

706

707

== 5.2 Power Consumption ==

708

709

WSC1-L (without external sensor): Idle: 4mA, Transmit: max 40mA

710

711

712

== 5.3 Storage & Operation Temperature ==

-20°C to +60°C

== 5.4 Pin Mapping ==

718

719

[[image:1656054149793-239.png]]

== 5.5 Mechanical ==

Refer LSn50v2 enclosure drawing in: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=LSN50-LoRaST/Mechanical_Drawing/>>url:https://www.dragino.com/downloads/index.php?dir=LSN50-LoRaST/Mechanical_Drawing/]]

725

726

727

== 5.6 Connect to RS485 Sensors ==

728

729

WSC1-L includes a RS485 converter PCB. Which help it easy to connect multiply RS485 sensors. Below is the photo for reference.

730

731

732

[[image:1656054389031-379.png]]

733

734

735

Hardware Design for the Converter Board please see:

736

737

[[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Weather_Station/RS485_Converter_Board/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Weather_Station/RS485_Converter_Board/]]

738

739

740

= 6. Weather Sensors =

741

742

== 6.1 Rain Gauge ~-~- WSS-01 ==

(((

WSS-01 RS485 Rain Gauge is used in meteorology and hydrology to gather and measure the amount of liquid precipitation (mainly rainfall) over an area.

)))

(((

WSS-01 uses a tipping bucket to detect rainfall. The tipping bucket use 3D streamline shape to make sure it works smoothly and is easy to clean.

)))

(((

WSS-01 is designed to support the Dragino Weather station solution. Users only need to connect WSS-01 RS485 interface to WSC1-L. The weather station main processor WSC1-L can detect and upload the rainfall to the IoT Server via wireless LoRaWAN protocol

)))

(((

The tipping bucket of WSS-01 is adjusted to the best angle. When installation, user only needs to screw up and adjust the bottom horizontally.

)))

(((

WSS-01 package includes screw which can be installed to ground. If user want to install WSS-01 on pole, they can purchase WS-K2 bracket kit.

)))

=== 6.1.1 Feature ===

767

768

* RS485 Rain Gauge

769

* Small dimension, easy to install

770

* Vents under funnel, avoid leaf or other things to avoid rain flow.

771

* ABS enclosure.

772

* Horizontal adjustable.

773

774

=== 6.1.2 Specification ===

* Resolution: 0.2mm

* Accuracy: ±3%

* Range: 0 ~~ 100mm

* Rainfall strength: 0mm～4mm/min (max 8mm/min)

780

* Input Power: DC 5~~24v

781

* Interface: RS485

782

* Working Temperature: 0℃～70℃ ( incorrect below 0 degree, because water become ICE)

783

* Working Humidity: <100% (no dewing)

784

* Power Consumption: 4mA @ 12v.

785

786

=== 6.1.3 Dimension ===

787

788

[[image:1656054957406-980.png]]

789

790

791

=== 6.1.4 Pin Mapping ===

792

793

[[image:1656054972828-692.png]]

794

795

796

=== 6.1.5 Installation Notice ===

797

798

(((

799

Do not power on while connect the cables. Double check the wiring before power on.

)))

(((

Installation Photo as reference:

)))

(((

(% style="color:#4472c4" %)** Install on Ground:**

)))

(((

WSS-01 Rain Gauge include screws so can install in ground directly .

)))

(((

(% style="color:#4472c4" %)** Install on pole:**

)))

(((

If user want to install on pole, they can purchase the (% style="color:#4472c4" %)** WS-K2 : Bracket Kit for Pole installation**(%%), and install as below:

822

)))

823

824

[[image:image-20220624152218-1.png||height="526" width="276"]]

825

826

WS-K2: Bracket Kit for Pole installation

827

828

829

WSSC-K2 dimension document, please see:

830

831

[[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Weather_Station/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Weather_Station/]]

832

833

834

== 6.2 Wind Speed/Direction ~-~- WSS-02 ==

835

836

[[image:1656055444035-179.png]]

837

838

(((

839

WSS-02 is a RS485 wind speed and wind direction monitor designed for weather station solution.

)))

(((

WSS-02 shell is made of polycarbonate composite material, which has good anti-corrosion and anti-corrosion characteristics, and ensure the long-term use of the sensor without rust. At the same time, it cooperates with the internal smooth bearing system to ensure the stability of information collection

)))

(((

Users only need to connect WSS-02 RS485 interface to WSC1-L. The weather station main processor WSC1-L can detect and upload the wind speed and direction to the IoT Server via wireless LoRaWAN protocol.

)))

=== 6.2.1 Feature ===

852

853

* RS485 wind speed / direction sensor

854

* PC enclosure, resist corrosion

855

856

=== 6.2.2 Specification ===

857

858

* Wind speed range: 0 ~~ 30m/s, (always show 30m/s for higher speed)

859

* Wind direction range: 0 ~~ 360°

860

* Start wind speed: ≤0.3m/s

861

* Accuracy: ±（0.3＋0.03V）m/s , ±1°

862

* Input Power: DC 5~~24v

863

* Interface: RS485

864

* Working Temperature: -30℃～70℃

865

* Working Humidity: <100% (no dewing)

866

* Power Consumption: 13mA ~~ 12v.

867

* Cable Length: 2 meters

868

869

=== 6.2.3 Dimension ===

870

871

[[image:image-20220624152813-2.png]]

872

873

874

=== 6.2.4 Pin Mapping ===

875

876

[[image:1656056281231-994.png]]

877

878

879

=== 6.2.5 Angle Mapping ===

880

881

[[image:1656056303845-585.png]]

882

883

884

=== 6.2.6 Installation Notice ===

885

886

(((

887

Do not power on while connect the cables. Double check the wiring before power on.

)))

(((

The sensor must be installed with below direction, towards North.

892

)))

893

894

[[image:image-20220624153901-3.png]]

895

896

897

== 6.3 CO2/PM2.5/PM10 ~-~- WSS-03 ==

(((

WSS-03 is a RS485 Air Quality sensor. It can monitor CO2, PM2.5 and PM10 at the same time.

)))

(((

WSS-03 uses weather proof shield which can make sure the sensors are well protected against UV & radiation.

)))

(((

WSS-03 is designed to support the Dragino Weather station solution. Users only need to connect WSS-03 RS485 interface to WSC1-L. The weather station main processor WSC1-L can detect and upload the environment CO2, PM2.5 and PM10 to the IoT Server via wireless LoRaWAN protocol.

)))

=== 6.3.1 Feature ===

914

915

* RS485 CO2, PM2.5, PM10 sensor

916

* NDIR to measure CO2 with Internal Temperature Compensation

917

* Laser Beam Scattering to PM2.5 and PM10

918

919

=== 6.3.2 Specification ===

920

921

* CO2 Range: 0～5000ppm, accuracy: ±3%F•S（25℃）

922

* CO2 resolution: 1ppm

923

* PM2.5/PM10 Range: 0～1000μg/m3 , accuracy ±3%F•S（25℃）

924

* PM2.5/PM10 resolution: 1μg/m3

925

* Input Power: DC 7 ~~ 24v

926

* Preheat time: 3min

927

* Interface: RS485

928

* Working Temperature:

929

** CO2: 0℃～50℃;

930

** PM2.5/PM10: -30 ~~ 50℃

931

* Working Humidity:

932

** PM2.5/PM10: 15～80%RH (no dewing)

933

** CO2: 0～95%RH

934

* Power Consumption: 50mA@ 12v.

935

936

=== 6.3.3 Dimension ===

937

938

[[image:1656056708366-230.png]]

939

940

941

=== 6.3.4 Pin Mapping ===

942

943

[[image:1656056722648-743.png]]

944

945

946

=== 6.3.5 Installation Notice ===

947

948

Do not power on while connect the cables. Double check the wiring before power on.

949

950

[[image:1656056751153-304.png]]

951

952

[[image:1656056766224-773.png]]

953

954

955

== 6.4 Rain/Snow Detect ~-~- WSS-04 ==

(((

WSS-04 is a RS485 rain / snow detect sensor. It can monitor Rain or Snow event.

)))

(((

WSS-04 has auto heating feature, this ensures measurement more reliable.

)))

(((

WSS-04 is designed to support the Dragino Weather station solution. Users only need to connect WSS-04 RS485 interface to WSC1-L. The weather station main processor WSC1-L can detect and upload the SNOW/Rain Event to the IoT Server via wireless LoRaWAN protocol.

)))

=== 6.4.1 Feature ===

973

974

* RS485 Rain/Snow detect sensor

975

* Surface heating to dry

976

* grid electrode uses Electroless Nickel/Immersion Gold design for resist corrosion

977

978

=== 6.4.2 Specification ===

979

980

* Detect if there is rain or snow

981

* Input Power: DC 12 ~~ 24v

982

* Interface: RS485

983

* Working Temperature: -30℃～70℃

984

* Working Humidity: 10～90%RH

985

* Power Consumption:

986

** No heating: 12mA @ 12v,

987

** heating: 94ma @ 12v.

988

989

=== 6.4.3 Dimension ===

990

991

[[image:1656056844782-155.png]]

992

993

994

=== 6.4.4 Pin Mapping ===

995

996

[[image:1656056855590-754.png]]

997

998

999

=== 6.4.5 Installation Notice ===

1000

1001

Do not power on while connect the cables. Double check the wiring before power on.

(((

Install with 15°degree.

1006

)))

1007

1008

[[image:1656056873783-780.png]]

1009

1010

1011

[[image:1656056883736-804.png]]

1012

1013

1014

=== 6.4.6 Heating ===

1015

1016

(((

1017

WSS-04 supports auto-heat feature. When the temperature is below the heat start temperature 15℃, WSS-04 starts to heat and stop at stop temperature (default is 25℃).

)))

== 6.5 Temperature, Humidity, Illuminance, Pressure ~-~- WSS-05 ==

(((

WSS-05 is a 4 in 1 RS485 sensor which can monitor Temperature, Humidity, Illuminance and Pressure at the same time.

)))

(((

WSS-05 is designed to support the Dragino Weather station solution. Users only need to connect WSS-05 RS485 interface to WSC1-L. The weather station main processor WSC1-L can detect and upload environment Temperature, Humidity, Illuminance, Pressure to the IoT Server via wireless LoRaWAN protocol.

)))

=== 6.5.1 Feature ===

1034

1035

* RS485 Temperature, Humidity, Illuminance, Pressure sensor

1036

1037

=== 6.5.2 Specification ===

1038

1039

* Input Power: DC 12 ~~ 24v

1040

* Interface: RS485

1041

* Temperature Sensor Spec:

** Range: -30 ~~ 70℃

** resolution 0.1℃

** Accuracy: ±0.5℃

* Humidity Sensor Spec:

1046

** Range: 0 ~~ 100% RH

1047

** resolution 0.1 %RH

1048

** Accuracy: 3% RH

1049

* Pressure Sensor Spec:

1050

** Range: 10～1100hPa

1051

** Resolution: 0.1hPa

1052

** Accuracy: ±0.1hPa

1053

* Illuminate sensor:

1054

** Range: 0～2/20/200kLux

1055

** Resolution: 10 Lux

1056

** Accuracy: ±3％FS

1057

* Working Temperature: -30℃～70℃

1058

* Working Humidity: 10～90%RH

1059

* Power Consumption: 4mA @ 12v

1060

1061

=== 6.5.3 Dimension ===

1062

1063

[[image:1656057170639-522.png]]

1064

1065

1066

=== 6.5.4 Pin Mapping ===

1067

1068

[[image:1656057181899-910.png]]

1069

1070

1071

=== 6.5.5 Installation Notice ===

1072

1073

Do not power on while connect the cables. Double check the wiring before power on.

1074

1075

[[image:1656057199955-514.png]]

1076

1077

1078

[[image:1656057212438-475.png]]

1079

1080

1081

== 6.6 Total Solar Radiation sensor ~-~- WSS-06 ==

(((

WSS-06 is Total Radiation Sensor can be used to measure the total solar radiation in the spectral range of 0.3 to 3 μm (300 to 3000 nm). If the sensor face is down, the reflected radiation can be measured, and the shading ring can also be used to measure the scattered radiation.

)))

(((

The core device of the radiation sensor is a high-precision photosensitive element, which has good stability and high precision; at the same time, a precision-machined PTTE radiation cover is installed outside the sensing element, which effectively prevents environmental factors from affecting its performance

)))

(((

WSS-06 is designed to support the Dragino Weather station solution. Users only need to connect WSS-06 RS485 interface to WSC1-L. The weather station main processor WSC1-L can detect and upload Total Solar Radiation to the IoT Server via wireless LoRaWAN protocol.

)))

=== 6.6.1 Feature ===

1099

1100

* RS485 Total Solar Radiation sensor

1101

* Measure Total Radiation between 0.3～3μm（300～3000nm）

1102

* Measure Reflected Radiation if sense area towards ground.

1103

1104

=== 6.6.2 Specification ===

1105

1106

* Input Power: DC 5 ~~ 24v

1107

* Interface: RS485

1108

* Detect spectrum: 0.3～3μm（300～3000nm）

1109

* Measure strength range: 0～2000W/m2

1110

* Resolution: 0.1W/m2

1111

* Accuracy: ±3%

1112

* Yearly Stability: ≤±2％

1113

* Cosine response: ≤7％ (@ Sun angle 10°)

1114

* Temperature Effect: ±2％（－10℃～40℃）

1115

* Working Temperature: -40℃～70℃

1116

* Working Humidity: 10～90%RH

1117

* Power Consumption: 4mA @ 12v

1118

1119

=== 6.6.3 Dimension ===

1120

1121

[[image:1656057348695-898.png]]

1122

1123

1124

=== 6.6.4 Pin Mapping ===

1125

1126

[[image:1656057359343-744.png]]

1127

1128

1129

=== 6.6.5 Installation Notice ===

1130

1131

Do not power on while connect the cables. Double check the wiring before power on.

1132

1133

[[image:1656057369259-804.png]]

1134

1135

1136

[[image:1656057377943-564.png]]

1137

1138

1139

== 6.7 PAR (Photosynthetically Available Radiation) ~-~- WSS-07 ==

(((

WSS-07 photosynthetically active radiation sensor is mainly used to measure the photosynthetically active radiation of natural light in the wavelength range of 400-700nm.

)))

(((

WSS-07 use precision optical detectors and has an optical filter of 400-700nm, when natural light is irradiated, a voltage signal proportional to the intensity of the incident radiation is generated, and its luminous flux density is proportional to the cosine of the direct angle of the incident light.

)))

(((

WSS-07 is designed to support the Dragino Weather station solution. Users only need to connect WSS-07 RS485 interface to WSC1-L. The weather station main processor WSC1-L can detect and upload Photosynthetically Available Radiation to the IoT Server via wireless LoRaWAN protocol.

)))

=== 6.7.1 Feature ===

1156

1157

(((

1158

PAR (Photosynthetically Available Radiation) sensor measure 400 ~~ 700nm wavelength nature light's Photosynthetically Available Radiation.

)))

(((

When nature light shine on the sense area, it will generate a signal base on the incidence radiation strength.

)))

=== 6.7.2 Specification ===

1167

1168

* Input Power: DC 5 ~~ 24v

1169

* Interface: RS485

1170

* Response Spectrum: 400～700nm

1171

* Measure range: 0～2500μmol/m2•s

1172

* Resolution: 1μmol/m2•s

1173

* Accuracy: ±2%

1174

* Yearly Stability: ≤±2％

1175

* Working Temperature: -30℃～75℃

1176

* Working Humidity: 10～90%RH

1177

* Power Consumption: 3mA @ 12v

1178

1179

=== 6.7.3 Dimension ===

1180

1181

[[image:1656057538793-888.png]]

1182

1183

1184

=== 6.7.4 Pin Mapping ===

1185

1186

[[image:1656057548116-203.png]]

1187

1188

1189

=== 6.7.5 Installation Notice ===

1190

1191

Do not power on while connect the cables. Double check the wiring before power on.

1192

1193

1194

[[image:1656057557191-895.png]]

1195

1196

1197

[[image:1656057565783-251.png]]

= 7. FAQ =

== 7.1 What else do I need to purchase to build Weather Station? ==

1203

1204

Below is the installation photo and structure:

1205

1206

[[image:1656057598349-319.png]]

1207

1208

1209

[[image:1656057608049-693.png]]

== 7.2 How to upgrade firmware for WSC1-L? ==

1214

1215

(((

1216

Firmware Location & Change log:

)))

(((

[[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/WSC1-L/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/WSC1-L/]]

)))

(((

Firmware Upgrade instruction: [[Firmware Upgrade Instruction>>doc:Main.Firmware Upgrade Instruction for STM32 base products.WebHome||anchor="H2.HardwareUpgradeMethodSupportList"]]

)))

== 7.3 How to change the LoRa Frequency Bands/Region? ==

1230

1231

User can follow the introduction for how to [[upgrade image>>||anchor="H7.2HowtoupgradefirmwareforWSC1-L3F"]]. When download the images, choose the required image file for download.

1232

1233

1234

== 7.4 Can I add my weather sensors? ==

1235

1236

Yes, connect the sensor to RS485 bus and see instruction: [[add sensors.>>||anchor="H3.3AddorDeleteRS485Sensor"]]

1237

1238

1239

= 8. Trouble Shooting =

1240

1241

== 8.1 AT Command input doesn't work ==

1242

1243

(((

1244

In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.

)))

= 9. Order Info =

== 9.1 Main Process Unit ==

1251

1252

Part Number: (% style="color:blue" %)**WSC1-L-XX**

1253

1254

(% style="color:blue" %)**XX**(%%): The default frequency band

1255

1256

* (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band

1257

* (% style="color:red" %)**AU915**(%%): LoRaWAN AU915 band

1258

* (% style="color:red" %)**EU433**(%%): LoRaWAN EU433 band

1259

* (% style="color:red" %)**EU868**(%%): LoRaWAN EU868 band

1260

* (% style="color:red" %)**KR920**(%%): LoRaWAN KR920 band

1261

* (% style="color:red" %)**US915**(%%): LoRaWAN US915 band

1262

* (% style="color:red" %)**IN865**(%%): LoRaWAN IN865 band

1263

* (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band

== 9.2 Sensors ==

(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:500px" %)

1268

|=(% style="width: 300px;" %)**Sensor Model**|=(% style="width: 200px;" %)**Part Number**

1269

|(% style="width:462px" %)**Rain Gauge**|(% style="width:120px" %)WSS-01

1270

|(% style="width:462px" %)**Rain Gauge installation Bracket for Pole**|(% style="width:120px" %)WS-K2

1271

|(% style="width:462px" %)**Wind Speed Direction 2 in 1 Sensor**|(% style="width:120px" %)WSS-02

1272

|(% style="width:462px" %)**CO2/PM2.5/PM10 3 in 1 Sensor**|(% style="width:120px" %)WSS-03

1273

|(% style="width:462px" %)**Rain/Snow Detect Sensor**|(% style="width:120px" %)WSS-04

1274

|(% style="width:462px" %)**Temperature, Humidity, illuminance and Pressure 4 in 1 sensor**|(% style="width:120px" %)WSS-05

1275

|(% style="width:462px" %)**Total Solar Radiation Sensor**|(% style="width:120px" %)WSS-06

1276

|(% style="width:462px" %)**PAR (Photosynthetically Available Radiation)**|(% style="width:120px" %)WSS-07

= 10. Support =

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

1281

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:file:///D:/市场资料/说明书/LoRa/LT系列/support@dragino.com]]

1282

1283

= 11. Appendix I: Field Installation Photo =

1284

1285

1286

[[image:1656058346362-132.png||height="685" width="732"]]

1287

1288

**Storage Battery**: 12v,12AH li battery

1289

1290