Wiki source code of HP0D Full Hotspot for Helium User Manual

Version 174.15 by Xiaoling on 2022/07/27 17:36

version	line-number	content
131.1	1	(% style="text-align:center" %)
	2	[[image:1651802206983-860.png\|\|height="427" width="398"]]
	3
	4
	5	(((
174.2	6
131.1	7
	8
	9	)))
	10
	11	Table of Contents：
	12
	13	{{toc/}}
	14
	15
	16	= 1. Introduction =
	17
	18	== 1.1 What is HP0D ==
	19
174.2	20
131.1	21	(((
	22	The HP0D is an outdoor LoRaWAN Gateway. It lets you bridge LoRa wireless network to an IP network via WiFi,Ethernet, optional 3G or 4G. The LoRa wireless allows users to send data and reach extremely long ranges at low data rates.
	23	)))
	24
	25	(((
	26	HP0D has passed Helium Full Hotspot Approval. It supports the (% style="color:#037691" %) miner feature from Helium (% style="color:black" %) and has a built-in ATECC608 encryption chip. It can be used as a Helium Full Hotspot for the project. It also supports Semtech packet forwarder and LoRaWAN Station connection, it is fully compatible with LoRaWAN protocol.HP0D supports two LoRaWAN servers at the same time, (% style="color:#037691" %)users can use HP0D for helium mining and connects max 2 x LoRaWAN servers at the same time.
	27	)))
	28
	29	(((
	30	(% style="color:#037691" %)Dragino already paid HP0D $40 onboarding cost and $10 location cost for each HP0D. (% style="color:black" %)It is ready to use for Helium, user only needs to input HNT wallet address and use QR Code to onboarding HP0D when it arrives.
	31	)))
	32
	33	(((
	34	HP0D has pre-configured standard LoRaWAN frequency bands to use for different countries. Users can also customize the frequency bands to use in their own LoRaWAN network.
174.2	35
	36
131.1	37	)))
	38
	39	== 1.2 Specifications ==
	40
	41	~ Hardware System:
	42	Linux Part:
	43
	44	* Raspberry Pi 4
	45
	46	~ Interface:
	47
	48	* 10M/100M RJ45 Ports x 1
	49	* LoRaWAN Wireless
	50	* Power Input: 12V 2A, DC
	51
	52	~ Operating Condition:
	53
	54	* Work Temperature: -20 ~~ 65°C
	55	* Storage Temperature: -20 ~~ 65°C
	56	* Power Input: 12V 2A, DC
	57
174.9	58
131.1	59	== 1.3 Features ==
	60
	61	* Open-Source Linux system
	62	* RPi4 with 2G /4G or 8G RAM
	63	* Managed by Web GUI, SSH via Internet
	64	* Support Semtech UDP packet forwarder
	65	* Support LoRaWAN Station Connection
	66	* Support Helium Miner
	67	* External fiberglass antenna
	68	* Firmware OTA
	69	* 802.3af PoE
	70	* Lighting Protection
	71	* Remote Monitoring
	72	* Support Helium LoRaWAN server and secondary LoRaWAN server
	73	* Include prepaid $40 onboarding cost and $10 location cost.
	74	* [[Remote.it remote management>>url:https://wiki.dragino.com/index.php?title=Reverse_SSH_Access#Use_Remote.it_service]].
	75
174.9	76
131.1	77	== 1.4 Label info and login name ==
	78
174.2	79
131.1	80	[[image:1651803959860-394.png\|\|height="500" width="375"]]
	81
	82
	83
	84	=== 1.4.1 Label information: ===
	85
174.2	86
174.12	87	(((
131.1	88	Device hostname: (% class="mark" %)dragino-xxxxxx(%%)
	89	Band: (% class="mark" %)US915/AU915/AS923_1-AS923_4/KR920/EU868/IN865/RU864(%%)
	90	Miner animal name: (% class="mark" %)xxx-xxx-xxx(%%)
	91	Miner address: (% class="mark" %)12xxxxxx(%%)
	92	Eth MAC address: (% class="mark" %)A8: 40: 41: EF: FE: CD(%%)
	93	Login: (% class="mark" %)root/d59f2d5b (the root is the Login account for the Web-UI and SSH.)(%%)
	94	SN: (% class="mark" %)device serial number.
174.12	95	)))
131.1	96
	97
174.2	98
131.1	99	= 2. Quick Start & Onboarding =
	100
174.2	101
174.13	102	(((
131.1	103	The HP0D is configured as a Wi-Fi Access Point by factory default. You can access and configure the HPD after connecting to its Wi-Fi network, or via its WAN Ethernet port.
174.13	104	)))
131.1	105
	106
	107	== 2.1 Connect HP0D Web UI ==
	108
	109
174.3	110	=== 2.1.1 via HP0D's Access Point ===
	111
	112
131.1	113	At the first boot of HP0D, it will auto-generate a Wi-Fi network
	114
	115
	116	[[image:1651804327535-321.png\|\|height="325" width="199"]]
	117
	118
	119	(% class="box infomessage" %)
	120	(((
	121	called : //HPD-dragino-xxxxxx//
	122	)))
	123
	124	(% class="box infomessage" %)
	125	(((
	126	with password: //dragino+dragino//
	127	You can use a PC to connect to this Wi-Fi network. The PC will get an IP address 10.130.1.xxx and the HP0D has the default IP 10.130.1.1
	128	)))
	129
	130
	131	[[image:1651804397792-591.png\|\|height="386" width="733"]]
	132
	133
174.2	134
131.1	135	=== 2.1.2 Connect via HP0D hostname ===
	136
174.2	137
174.14	138	(((
	139	Connect the HP0D Ethernet port to your router and HP0D will obtain an IP address. If your PC(Windows/Mac/Ubuntu) connects to the same network with the HP0D, you can access the HP0D Web-UI via HP0D's hostname.
	140	)))
131.1	141
174.15	142	Like: (% style="background-color:yellow" %)__//http:~/~/dragino-4ba54a//__
131.1	143
	144
	145	[[image:1651804629009-699.png]]
	146
174.2	147
	148
131.1	149	=== 2.1.3 Connect via Ethernet Port ===
	150
174.2	151
131.1	152	//Connect the HP0D Ethernet port to your router and HP0D will obtain an IP address from your router. In the router’s management portal, you should be able to find what IP address the router has assigned to the HP0D.//
	153
	154
	155	//If you get the IP address from the router, like: (% class="mark" %)10.130.2.42(%%), you can use this IP address to connect the WEB UI or SSH access of HP0D.//
	156
	157
	158	[[image:1651804782523-623.png]]
	159
	160
174.2	161
131.1	162	== 2.2 Generate QR Code ==
	163
	164
	165	(((
174.3	166	//Go to (% style="color:#037691" %)Miner ~-~-> QR Generate(%%), input your Helium Wallet Address, and click Generate.//
131.1	167	)))
	168
	169	(((
174.3	170	(% style="color:red" %)//Note: After onboarding, this wallet will become the owner of this hotspot.//
131.1	171
	172
	173	)))
	174
	175	[[image:image-20220506140312-1.png\|\|height="435" width="438"]]
	176
	177
174.2	178
131.1	179	== 2.3 Onboarding Hotspot ==
	180
	181
	182	(((
	183	//1. Download the Helium Hotspot APP from the Apple or Google Play store.//
	184	)))
	185
	186	(((
174.2	187	(% style="color:red" %)//Note: the APP version needs to be greater than 3.11.//
131.1	188
	189
	190	)))
	191
	192	(((
174.2	193	//2. To add a hotspot, select (% style="color:blue" %)“Hotspot”(%%). On this tab, click the (% style="color:blue" %)“+ Add Hotspot"(%%) in the mid where choose the (% style="color:blue" %)"DRAGINO Miner HP0D"//
131.1	194
	195
	196	)))
	197
	198	[[image:1651817186037-899.png\|\|height="429" width="206"]] [[image:1651817194458-938.png\|\|height="434" width="203"]]
	199
	200
174.2	201
131.1	202	//3. Scan the QR Code you generated in the previous step.//
	203
	204	[[image:1651828211026-220.png\|\|height="405" width="191"]]
	205
	206
174.2	207
131.1	208	(((
	209	//4. Onboarding your device//
	210	)))
	211
	212	(((
174.10	213	Mobile APP will get info from the onboarding server. If the MAC address doesn't appear, it means the network connection of the mobile to the onboarding server might have an issue.
131.1	214
	215
	216	)))
	217
	218	[[image:image-20220506141159-2.png\|\|height="422" width="202"]] [[image:1651817529289-461.png\|\|height="423" width="199"]]
	219
	220	[[image:1651828250802-391.png\|\|height="421" width="197"]] [[image:1651828262668-768.png\|\|height="416" width="196"]](% style="display:none" %)
	221
	222
	223	5. //Check onboarding status where you can check from mobile~://
	224
	225	[[image:1651828391664-884.png\|\|height="413" width="197"]] [[image:1651828401011-970.png\|\|height="412" width="193"]](% style="display:none" %)
	226
	227
	228	//You can also see the hotspot status in the below link~://
	229
	230	//https:~/~/explorer.helium.com/hotspots/<(% class="mark" %)YOUR_HOTSPORT_KEY(%%)>//
	231
	232	//Example~://
	233
	234
	235	//Green Synced means hotspot works normally.//
	236
	237	[[image:1651828427715-679.png\|\|height="374" width="635"]]
	238
	239
174.4	240
131.1	241	== 2.4 Set the Port Forwarding ==
	242
	243
	244	(((
	245	//Helium Hotspots may not work if the Hotspot is behind a firewall or uses an incompatible NAT type. Other times it may be because of a router configuration or the internet is offline. This article aims to help resolve any issues you may have.//
	246	)))
	247
	248	[[image:1651828514449-658.png]]
	249
	250	(((
	251
	252	)))
	253
	254	(((
174.11	255	(((
174.4	256	(% style="color:red" %)Note: Please refer to more detailed Settings
131.1	257	)))
174.11	258	)))
131.1	259
	260	(((
174.11	261	(((
131.1	262	[[https:~~/~~/docs.helium.com/troubleshooting/network-troubleshooting/>>url:https://docs.helium.com/troubleshooting/network-troubleshooting/]]
	263	)))
174.11	264	)))
131.1	265
	266	(((
174.11	267	(((
131.1	268	[[https:~~/~~/www.youtube.com/watch?v=GKusVC7ovrE>>url:https://www.youtube.com/watch?v=GKusVC7ovrE]]
174.11	269	)))
131.1	270
174.4	271
131.1	272
	273	)))
	274
	275	= 3. Check the configuration of HP0D =
	276
	277	== 3.1 LoRa frequency configuration ==
	278
	279
	280	[[image:1651828687205-178.png\|\|height="323" width="657"]]
	281
	282
174.5	283
131.1	284	== 3.2 Check the LoRaWAN Server Address ==
	285
	286
	287	[[image:image-20220607160428-1.png\|\|height="472" width="654"]]
	288
	289
174.5	290
131.1	291	== 3.2.1 Configure the Secondary LoRaWAN Server ==
	292
174.5	293
131.1	294	[[image:image-20220607161130-2.png\|\|height="501" width="1112"]]
	295
160.1	296
131.1	297	[[image:image-20220607161603-3.png\|\|height="557" width="1113"]]
	298
160.1	299
131.1	300	[[image:image-20220607161812-4.png\|\|height="699" width="1115"]]
	301
	302
	303
	304	== 3.3 Check Miner configuration ==
	305
	306
	307	[[image:image-20220506181408-1.png\|\|height="451" width="513"]]
	308
174.5	309
131.1	310	(((
174.5	311	(% style="color:red" %)//Note: Check the Region and Height, the default height is greater than 1, if it is 1 please Click the mid button of Update, and then wait 10mins to check here.//
131.1	312
	313
174.5	314
131.1	315	== //3.4 Check the Miner state// ==
	316
	317
	318	[[image:image-20220531171836-9.png\|\|height="776" width="1155"]]
	319
	320
174.11	321	(((
	322	(% style="color:red" %)//Note: Absorption status can show whether the hotspot is working properly The p2p network can see how your hotspot is interacting with the surrounding hotspots usually, the nat_type should be '//(% style="color:blue" %)//none'//
	323	)))
131.1	324
	325
	326
	327	)))
	328
	329	= 4. Installation of Antenna =
	330
	331
	332	(((
	333	//HP0D uses Fiber Glass Antenna.//
	334	)))
	335
	336	[[image:1651832158606-882.png]]
	337
	338	(((
	339
	340	)))
	341
	342	(((
174.5	343	//The user needs to connect the antenna cable's SMA connector to the HP03 and connect the N-Type connector to the antenna and install it as below~://
131.1	344	)))
	345
	346	(((
	347	[[image:1651832205608-998.png\|\|height="349" width="198"]]
	348
174.5	349
131.1	350
	351	)))
	352
	353	= 5. SSH Access for Linux console =
	354
	355
	356	//Connect the HP0D Ethernet port to your router and HP0D will obtain an IP address from your router.//
	357
	358	//In the router's management portal, you should be able to find what IP address the router has assigned to the HP0D.//
	359
	360	//You can use this IP or hostname of HP0D to connect the WEB UI or SSH access of HP0D.//
	361
	362	//Make sure your PC and the HP0D are in the same network, the use an SSH tool (such as [[putty>>url:http://www.chiark.greenend.org.uk/~~sgtatham/putty/download.html]]) to access it.//
	363
	364
	365	Below are screenshots:
	366
	367	[[image:image-20220608202027-1.png]]
	368
	369	(((
	370	//IP address: IP address of HP0D or hostname of HP0D ((% class="mark" %)Such as dragino-7df4af(%%))//
	371	)))
	372
	373	(((
	374	//Port: 22//
	375	)))
	376
	377	(((
	378	//User Name: (% style="color:green" %)root//
	379	)))
	380
	381	(((
	382	//Password: (% style="color:green" %)Randomly generated （found on device’s label）//
	383
	384
	385	)))
	386
	387	(((
	388	//After logging in, you will be in the Linux console and can enter commands as shown below.//
	389
	390
	391	)))
	392
	393	[[image:image-20220608202118-2.png]]
	394
	395
174.6	396
131.1	397	= 6. How to change the Wireless function of HP0D =
	398
174.6	399
131.1	400	//The wireless function is configured as AP by default and the web page does not support configuration,//
	401
	402	//if you want to configure it as STA(client)connection mode,//
	403
174.6	404	//you can configure your WiFi info on the (% style="color:blue" %)/Network/WiFi (%%)page.//
131.1	405
	406
174.6	407	(% style="color:red" %)//Note: the wireless state is as AP//
131.1	408
	409	[[image:image-20220531170243-5.png\|\|height="469" width="967"]]
	410
	411
174.6	412
131.1	413	== 6.1 Access WiFi configuration page ==
	414
	415
	416	[[image:image-20220531165803-2.png]]
	417
	418
174.6	419
131.1	420	== 6.2 Enter your WiFi information and save ==
	421
	422
	423	[[image:image-20220531165958-3.png]]
	424
	425
174.6	426
131.1	427	== 6.3 Change the WiFi mode. ==
	428
	429
	430	[[image:image-20220531170131-4.png]]
	431
174.6	432
	433
131.1	434	== 6.4 Wait system to restart ==
	435
	436
	437	[[image:image-20220531170501-7.png]]
	438
	439
174.6	440	(% style="color:red" %)//Note: When the time remaining is finished it will turn to the home page.//
131.1	441
	442
174.6	443
131.1	444	== 6.5 Check the STA state ==
	445
	446
	447	[[image:image-20220531170705-8.png\|\|height="484" width="990"]]
	448
	449
174.6	450
131.1	451	= 7. Trouble Shootings =
	452
	453	== 7.1 How to get a wallet address? ==
	454
	455
	456	//Download the helium Hotspots APP on the Apple or Google Play store to generate your own wallet.//
	457
	458
174.6	459
131.1	460	== 7.2 Onboarding ~-~- Unable to access Web-UI ~-~-> Miner ==
	461
	462
	463	(((
	464	//Users can log in to the HP0D, able to access other Web Pages except for the miner page.//
	465	)))
	466
	467	(((
	468	//If you first boot the device where you need to wait for 10 mins for the initialization connection to the Helium server.//
	469
174.6	470
131.1	471
	472	)))
	473
	474	== 7.3 Onboarding ~-~- Some parameters on the miner page show timeout ==
	475
	476
	477	[[image:image-20220506182042-2.png\|\|height="250" width="516"]]
	478
	479	[[image:1651832455372-647.png\|\|height="224" width="520"]]
	480
	481
	482	//HP0D is establishing a connection to the Helium server and is not finished. And you might see above.//
	483
	484	//It might relate to the network which might be up to 10mins.//
	485
	486
174.6	487
131.1	488	== 7.4 Onboarding – Bad Gateway ==
	489
	490
	491	[[image:1651832583790-633.png]]
	492
	493
	494	//This is caused by the process leading too long which just needs to refresh the page.//
	495
	496
174.6	497
131.1	498	== 7.5 Onboarding ~-~- Why did QR Code generate aways fail? ==
	499
	500
	501	[[image:image-20220506182424-3.png]]
	502
	503
	504	(((
	505	//This may be related to the current block height, if the device is synchronizing to the latest height or if the device block height is much lower than the current height as the above picture like '1 1', the QR code generation may fail.//
	506
174.6	507
131.1	508
	509	)))
	510
	511	== 7.6 Onboarding ~-~- Why is the QR Code not quite the same as the manual? ==
	512
174.6	513
131.1	514	[[image:1651832742262-209.png\|\|height="297" width="365"]]
	515
	516
	517	(((
174.6	518	//Please ensure that you enter the correct wallet address and that your network is up and running, the user can click the button of (% style="color:red" %)‘Clean’(%%) to re-generate the QR Code.//
131.1	519
174.6	520
131.1	521
	522	)))
	523
	524	== 7.7 Onboarding – MAC address is ‘Unknown’ after scan QR Code ==
	525
	526
	527	[[image:1651832811038-780.png\|\|height="462" width="216"]]
	528
	529
	530	(((
174.6	531	//If you see the MAC Address shows the (% style="color:red" %)‘Unknown’(%%) where is due to the provisioning error, please contact us to help you solve it.//
131.1	532
174.6	533
131.1	534
	535	)))
	536
174.6	537	== 7.8 Onboarding – MAC address is being refreshed after scanning the QR Code ==
131.1	538
	539
	540	(((
	541	//After scanning the QR Code, Mobile APP will connect to the Helium onboarding server and provide the public key/ wallet address to the onboarding server. The server will return the match MAC address for this hotspot.//
	542
	543
	544	)))
	545
	546	(((
174.6	547	//If you don't see the MAC address, make sure your mobile has a good internet connection.//
131.1	548	)))
	549
	550	[[image:1651832880009-473.png]]
	551
	552
	553
174.6	554	== 7.9 HP0D Web ~-~-> Miner ~-~-> Version shows ‘short’ ==
131.1	555
174.6	556
131.1	557	//This is caused by the server connection delay, which does not affect the regular use.//
	558
	559	[[image:1651832959907-357.png]]
	560
	561
174.6	562
131.1	563	== 7.10 Mobile APP crash after scanning the QR Code? ==
	564
	565
	566	* //Make sure you have input the correct Wallet address to generate QR Code.//
	567	* //Make sure your mobile app uses the same wallet address as the one to generate QR Code.//
174.6	568	* //Make sure your mobile app's relevant permission is enabled.//
131.1	569	* //Known: The Android 11 version may cause this kind of issue.//
	570
	571	== 7.11 Why the frequency/region is not the same as what I purchased? ==
	572
	573
	574	(((
	575	//Each HP0D is inspected and configured prior to shipping.//
	576	)))
	577
	578	(((
	579	//If your HP0D Web-UI – Miner region is not the same as the shell labels, please contact our support team that will solve this issue for you.//
	580
174.6	581
131.1	582
	583	)))
	584
	585	== 7.12 Can use the frequency to a region where is no support? ==
	586
	587
	588	(((
	589	//Please make sure that the region supports this frequency, you can confirm the appropriate frequency through this link://
	590	)))
	591
	592	(((
	593	[[https:~~/~~/docs.helium.com/lorawan-on-helium/frequency-plans>>url:https://docs.helium.com/lorawan-on-helium/frequency-plans]]
	594
174.6	595
131.1	596
	597	)))
	598
	599	== 7.13 Can change the frequency of the HP0D Miner? ==
	600
	601
	602	//We do not recommend doing this, it may damage your device//
	603
	604
174.6	605
131.1	606	== 7.14 Low Reward and not transmit issue ==
	607
	608
	609	//We had released the 0524 version for the miner, Users can check the miner version in the HP0D web UI.//
	610
	611	//If it is lower than the 0524 version, users can manually upgrade it via the 'draginoups' command in the HP0D's CLI.//
	612
	613	[[image:image-20220527114519-1.png\|\|height="579" width="851"]]
	614
	615
174.6	616
131.1	617	== 7.15 Why is my miner version not the latest ==
	618
	619
	620	//By default, as soon as a new version of helium is released, we will push the upgrade the same day.//
	621
	622	//However, the download and upgrade may fail due to the network.//
	623
150.1	624	You can reboot your hotspot where the hotspot will try to upgrade when per booting.
140.1	625
131.1	626
150.1	627	//and We offer manual check methods://
131.1	628
150.1	629	// Use the "draginoups" command to check//
140.1	630
	631
174.6	632	(% style="color:red" %)//Note: How to access the hotspot CLI refer to ( Such as ////[[Step 5.>>url:http://8.211.40.43/xwiki/bin/view/Main/User%20Manual%20for%20All%20Gateway%20models/HP0D#H5.SSHAccessforLinuxconsole]] )//
141.1	633
174.6	634
131.1	635	[[image:image-20220601101358-1.png]]
	636
	637
	638
145.2	639	== 7.16 Why is my miner running down? ==
	640
174.6	641
145.2	642	//the default, the Miner is managed by docker.//
	643
	644	//If you find the miner is offline where the miner is running down.//
	645
	646
	647	What You can do?
	648
174.6	649	(% style="color:blue" %)1. Reboot the hotspot and check again.
145.2	650
149.1	651	//Usually, if the miner is just down, then a reboot is the quickest way//
145.2	652
	653
174.6	654	(% style="color:blue" %)2. Reinstall the Miner manually.
145.2	655
149.1	656	//If rebooting does not solve the problem you can reinstall MINER by one of the following methods//
145.2	657
149.1	658	1). There is an update button in the middle of the miner page, click this button and then the miner will be reinstalled.
	659
	660
174.6	661	2). Run the (% style="color:red" %)"//minerup updat//e"(%%) command to reinstall the miner
149.1	662
	663
	664
145.2	665	[[image:image-20220610094825-2.png\|\|height="457" width="835"]]
	666
174.6	667
145.2	668	[[image:image-20220610094755-1.png\|\|height="706" width="834"]]
	669
	670
174.6	671
163.1	672	== 7.17 More commands for debugging. ==
145.2	673
	674
148.1	675	I'm trapped somewhere, what can I do first?
	676
	677
	678	//dragino provides a method of self-testing//
	679
	680	//1.) Is Hotspot's Miner running?//
	681
	682	//2). Is the miner version up to date?//
	683
	684	//3). Is the height gap between local height and remote height kept within 100//
	685
	686
174.6	687	(% style="color:red" %)//Note: You can find the above three points on the Miner page, and If you are familiar with the Linux command line you can use the following command//
148.1	688
	689
147.1	690	(% class="box infomessage" %)
	691	(((
	692	minerup update #~-~-> reinstall miner but not clearing memory
	693	minerup flush #~-~-> reinstall miner and clear memory
	694	minerup snap #~-~-> load a snap_short to sync the block height
148.1	695	minerup gap #~-~-> check the height between local and remote.
	696	draginoup #~-~-> check the miner version gap between local and remote.
155.1	697
	698
	699	doker ps #~-~-> show the miner running state
	700	miner versions #~-~-> show the miner version
147.1	701	)))
	702
	703
174.6	704
161.1	705	== 7.18 Why does my hotspot not have some of the features described in this WiKi ==
147.1	706
161.1	707
	708	//This is the result of the OTA not being updated in time//
	709
	710	//You can reboot your hotspot or upgrade these packages manually.//
	711
	712
	713	(% class="box infomessage" %)
	714	(((
	715	apt update
	716	apt install dragino*
	717	)))
	718
	719
174.6	720
155.1	721	= 8. How to flash a new OS for the hotspot, the hotspot's setting will be factory settings =
131.1	722
174.6	723
131.1	724	The hotspot is based on the Rpi-4B so the OS has been installed on the SD card.
	725
	726	So you have to re-flash the image into the SD card.
	727
174.6	728	(% style="background-color:yellow" %)Warning: Do not reset unless necessary
131.1	729
139.1	730
174.6	731	(% style="color:blue" %)//Preparations://
131.1	732
	733	1. //Open the HP0D shell, and take out the SD card from the Raspberry PI 4B (Make sure the SD card is empty )//
	734
	735	2. //Download the OS image~: ( Such as [[draginohp0d-1.9img>>url:http://repo.dragino.com/release/hp0d-image/draginohp0d-1.9.img]] )//
	736
	737	3. //A card reader device//
	738
	739	4. //A Flash software tool ( Such as [[balenaEtcher>>url:https://www.balena.io/etcher/]] )//
	740
	741	5. //SD Card [[formatter>>url:http://repo.dragino.com/release/tool/PanasonicSDFormatter.zip]]//
	742
	743
174.6	744	(% style="color:blue" %)HP0D's enclosure
158.1	745
	746
	747	[[image:image-20220615204902-1.png\|\|height="633" width="918"]]
	748
	749
	750	[[image:image-20220615204917-2.png\|\|height="1038" width="922"]]
	751
	752
	753
174.6	754	=== (% style="color:blue" %)Step 1. Formatting the SD Card(%%) ===
131.1	755
	756
	757	[[image:image-20220609111027-9.png]]
	758
	759
174.7	760
174.6	761	=== (% style="color:blue" %)Step 2. Select the OS image (%%) ===
131.1	762
	763
	764	[[image:image-20220609104907-8.png]]
	765
	766
174.7	767
174.6	768	=== (% style="color:blue" %)Step 3. Select the target (%%) ===
131.1	769
	770
	771	[[image:image-20220609104637-2.png]]
	772
	773	[[image:image-20220609104701-3.png]]
	774
	775
174.7	776
174.6	777	=== (% style="color:blue" %)Step 4. Flash start(%%) ===
131.1	778
	779
	780	[[image:image-20220609104727-4.png]]
	781
	782	[[image:image-20220609104741-5.png]]
	783
	784
174.6	785	=== (% style="color:blue" %)Flash Complete(%%) ===
131.1	786
	787
	788	[[image:image-20220609104415-1.png]]
	789
	790
	791	== Step 4. Re-install the SD card into the hotspot and boot it ==
	792
	793
174.6	794
131.1	795	== Step 5. Configure the correct region for the miner ==
	796
174.6	797
131.1	798	by the default, the factory settings apply to the US915.
	799
	800	if your region is not the US915, you have to configure the correct region for the miner.
	801
	802
	803	Access the hotspot CLI, and run these Linux commands
	804
	805
132.1	806	(% class="box infomessage" %)
	807	(((
131.1	808	~#~##update the software of dragino
	809
	810	apt update
	811
	812	apt install dragino*
132.1	813	)))
131.1	814
	815	[[image:image-20220609150452-2.png\|\|height="348" width="909"]]
	816
	817
	818
132.1	819	(% class="box infomessage" %)
	820	(((
131.1	821	~#~##configure the correct region for the miner and update it
	822
138.1	823	uci set miner.general.region=<Region; Such as AS923_1/AU915/US915/EU868/IN865>
131.1	824
	825	uci commit miner
	826
	827	minerup update
132.1	828	)))
131.1	829
137.1	830	[[image:image-20220609151513-5.png]]
131.1	831
	832
174.6	833
132.1	834	(% class="box infomessage" %)
	835	(((
131.1	836	~#~##check the miner version
	837
	838	draginoups
132.1	839	)))
131.1	840
135.1	841	[[image:image-20220609151419-3.png]]
131.1	842
143.1	843
174.6	844
143.1	845	(% class="box infomessage" %)
	846	(((
	847	~#~##unblock the function of wireless
	848	rfkill unblock wlan
	849	uci set wireless.general.mode=ap
	850	uci commit wireless
	851	)))
	852
	853	[[image:image-20220609161204-1.png]]
	854
131.1	855
160.1	856
174.1	857	= 9. How does the HP0D access to the network via a USB 4G Dongle =
160.1	858
174.6	859
172.1	860	We have reserved enough space inside the HP0D to use a USB 4G Dongle,
	861
	862	so you can install a USB 4G Dongle in order for the hotspot to access the network via 4G.
	863
	864
174.6	865	(% style="color:green" %)//Preparations://
172.1	866
	867	//1). A USB 4G Dongle, Such as HUAWEI E3327,ZTE...//
	868
	869	//2). A Sim card that can access the 4g network.//
	870
	871	//3). open the hotspot's shell.//
	872
	873
174.6	874
172.1	875	== 9.1. Open the HP0D shell and access the USB 4G Dongle into the Rpi. ==
	876
174.6	877
172.1	878	[[image:image-20220627153334-2.png]]
	879
	880
174.6	881
172.1	882	== 9.2. Checking the USB 4G Dongle network ==
	883
174.6	884
172.1	885	We have installed drivers for common USB 4G Dongle,
	886
	887	and managed by NetworkManager, once hp0d detects an available USB 4G Dongle it will try to dial up the range network
	888
	889
174.6	890	//HUAWEI-E3327//
172.1	891
	892	[[image:image-20220627154526-9.png\|\|height="762" width="725"]]
	893
	894
	895
174.6	896	//ZTE//
	897
172.1	898	[[image:image-20220627154201-5.png]]
	899
	900
	901
	902	= 10. PoE introduction =
	903
	904
174.6	905	//The HP0D is use the (% style="color:blue" %)IEEE 802.3 af compliant PoE port(%%) (input 44 ~~ 57 v, output 12V)//
160.1	906
161.1	907	//So you can use the PoE //switches// or PoE injector to power the device.//
160.1	908
	909
174.6	910	(((
	911	(% style="color:red" %)Note: The RJ45 Indicator light only represents the PoE power supply, so when you use DC to power the hotspot and the RJ45 indicator light is off ~-~--> this is normal
	912	)))
160.1	913
	914
174.6	915	(% style="background-color:yellow" %)Wiring schematic:
160.1	916
	917	[[image:image-20220616143347-1.png]]
	918
	919
	920
	921
173.1	922	= 11. OTA Version Info =
160.1	923
174.6	924
131.1	925	== When does the OTA update happen? ==
	926
	927
	928	//HP0D will check OTA update on a) Every Booting. b) Every Night. Below is the OTA update version info//
	929
174.6	930
	931
131.1	932	== # 2022/05/14 ==
	933
	934
	935	1. //Update to the latest miner version: miner-arm64_2022.05.13.0_GA//
	936	1. //Add postinst after auto-update//
	937	1. //Add Miner version mark.//
	938	1. //Add fast sync if miner GAP is large//
	939
152.1	940	== # 2022/05/18 ==
	941
	942
	943	1. //Update minerup to speed up synchronized blocks//
	944
131.1	945	== # 2022/05/24 ==
	946
151.1	947
152.1	948	1. //Update to the latest miner version: miner-arm64_2022.05.24.0_GA//
131.1	949
151.1	950	== # 2022/05/31 ==
131.1	951
174.6	952
152.1	953	1. //Add WiFi STA icon display//
	954	1. //Optimize AP icon display//
	955	1. //Optimize home icon display//
	956	1. //Fix for Miner icon URL bug//
	957	1. //Add the secondary server configuration//
151.1	958
173.1	959	= 12. Supports =
131.1	960
174.6	961
131.1	962	(((
	963	//If you are experiencing issues and can’t solve them, you can send mail to [[support@dragino.com>>mailto:support@dragino.com]].//
	964	)))
	965
	966	(((
	967	//With your question as detailed as possible. We will reply and help you in the shortest.//
	968
174.6	969
131.1	970
	971	)))
	972
173.1	973	= 13. Order Info =
131.1	974
	975
174.6	976	(% style="color:blue" %)HP0D-XXX
131.1	977
174.6	978	(% style="color:blue" %)XXX(%%): Frequency Band
131.1	979
174.6	980	* (% style="color:red" %)AS923(%%): LoRaWAN AS923 band
	981	* (% style="color:red" %)AU915(%%): LoRaWAN AU915 band
	982	* (% style="color:red" %)EU868(%%): LoRaWAN EU868 band
	983	* (% style="color:red" %)KR920(%%): LoRaWAN KR920 band
	984	* (% style="color:red" %)US915(%%): LoRaWAN US915 band
	985	* (% style="color:red" %)IN865(%%): LoRaWAN IN865 band
	986
173.1	987	= 14. Manufacturer Info =
131.1	988
174.6	989
131.1	990	(((
	991	Shenzhen Dragino Technology Development co. LTD
	992	)))
	993
	994	(((
	995	Room 202, Block B, BCT Incubation Bases (BaoChengTai), No.8 CaiYunRoad
	996	)))
	997
	998	(((
	999	Longcheng Street, LongGang District; Shenzhen 518116, China
	1000
	1001
	1002
	1003	)))
	1004
173.1	1005	= 15. FCC Warning =
131.1	1006
174.6	1007
131.1	1008	(((
	1009	This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
	1010	)))
	1011
	1012	(((
	1013	~-~- Reorient or relocate the receiving antenna.
	1014	)))
	1015
	1016	(((
	1017	~-~- Increase the separation between the equipment and receiver.
	1018	)))
	1019
	1020	(((
	1021	~-~- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
	1022	)))
	1023
	1024	(((
	1025	~-~- Consult the dealer or an experienced radio/TV technician for help.
	1026	)))
	1027
	1028	(((
	1029	Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
	1030	)))
	1031
	1032	(((
	1033	The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
	1034	)))

Wiki source code of HP0D Full Hotspot for Helium User Manual

Applications

Navigation