Wiki source code of HP0D Full Hotspot for Helium User Manual

Version 174.12 by Xiaoling on 2022/07/27 17:34

version	line-number	content
131.1	1	(% style="text-align:center" %)
	2	[[image:1651802206983-860.png\|\|height="427" width="398"]]
	3
	4
	5	(((
174.2	6
131.1	7
	8
	9	)))
	10
	11	Table of Contents：
	12
	13	{{toc/}}
	14
	15
	16	= 1. Introduction =
	17
	18	== 1.1 What is HP0D ==
	19
174.2	20
131.1	21	(((
	22	The HP0D is an outdoor LoRaWAN Gateway. It lets you bridge LoRa wireless network to an IP network via WiFi,Ethernet, optional 3G or 4G. The LoRa wireless allows users to send data and reach extremely long ranges at low data rates.
	23	)))
	24
	25	(((
	26	HP0D has passed Helium Full Hotspot Approval. It supports the (% style="color:#037691" %) miner feature from Helium (% style="color:black" %) and has a built-in ATECC608 encryption chip. It can be used as a Helium Full Hotspot for the project. It also supports Semtech packet forwarder and LoRaWAN Station connection, it is fully compatible with LoRaWAN protocol.HP0D supports two LoRaWAN servers at the same time, (% style="color:#037691" %)users can use HP0D for helium mining and connects max 2 x LoRaWAN servers at the same time.
	27	)))
	28
	29	(((
	30	(% style="color:#037691" %)Dragino already paid HP0D $40 onboarding cost and $10 location cost for each HP0D. (% style="color:black" %)It is ready to use for Helium, user only needs to input HNT wallet address and use QR Code to onboarding HP0D when it arrives.
	31	)))
	32
	33	(((
	34	HP0D has pre-configured standard LoRaWAN frequency bands to use for different countries. Users can also customize the frequency bands to use in their own LoRaWAN network.
174.2	35
	36
131.1	37	)))
	38
	39	== 1.2 Specifications ==
	40
	41	~ Hardware System:
	42	Linux Part:
	43
	44	* Raspberry Pi 4
	45
	46	~ Interface:
	47
	48	* 10M/100M RJ45 Ports x 1
	49	* LoRaWAN Wireless
	50	* Power Input: 12V 2A, DC
	51
	52	~ Operating Condition:
	53
	54	* Work Temperature: -20 ~~ 65°C
	55	* Storage Temperature: -20 ~~ 65°C
	56	* Power Input: 12V 2A, DC
	57
174.9	58
	59
131.1	60	== 1.3 Features ==
	61
	62	* Open-Source Linux system
	63	* RPi4 with 2G /4G or 8G RAM
	64	* Managed by Web GUI, SSH via Internet
	65	* Support Semtech UDP packet forwarder
	66	* Support LoRaWAN Station Connection
	67	* Support Helium Miner
	68	* External fiberglass antenna
	69	* Firmware OTA
	70	* 802.3af PoE
	71	* Lighting Protection
	72	* Remote Monitoring
	73	* Support Helium LoRaWAN server and secondary LoRaWAN server
	74	* Include prepaid $40 onboarding cost and $10 location cost.
	75	* [[Remote.it remote management>>url:https://wiki.dragino.com/index.php?title=Reverse_SSH_Access#Use_Remote.it_service]].
	76
174.9	77
	78
131.1	79	== 1.4 Label info and login name ==
	80
174.2	81
131.1	82	[[image:1651803959860-394.png\|\|height="500" width="375"]]
	83
	84
	85
	86	=== 1.4.1 Label information: ===
	87
174.2	88
174.12	89	(((
131.1	90	Device hostname: (% class="mark" %)dragino-xxxxxx(%%)
	91	Band: (% class="mark" %)US915/AU915/AS923_1-AS923_4/KR920/EU868/IN865/RU864(%%)
	92	Miner animal name: (% class="mark" %)xxx-xxx-xxx(%%)
	93	Miner address: (% class="mark" %)12xxxxxx(%%)
	94	Eth MAC address: (% class="mark" %)A8: 40: 41: EF: FE: CD(%%)
	95	Login: (% class="mark" %)root/d59f2d5b (the root is the Login account for the Web-UI and SSH.)(%%)
	96	SN: (% class="mark" %)device serial number.
174.12	97	)))
131.1	98
	99
174.2	100
131.1	101	= 2. Quick Start & Onboarding =
	102
174.2	103
131.1	104	The HP0D is configured as a Wi-Fi Access Point by factory default. You can access and configure the HPD after connecting to its Wi-Fi network, or via its WAN Ethernet port.
	105
	106
	107	== 2.1 Connect HP0D Web UI ==
	108
	109
174.3	110	=== 2.1.1 via HP0D's Access Point ===
	111
	112
131.1	113	At the first boot of HP0D, it will auto-generate a Wi-Fi network
	114
	115
	116	[[image:1651804327535-321.png\|\|height="325" width="199"]]
	117
	118
	119	(% class="box infomessage" %)
	120	(((
	121	called : //HPD-dragino-xxxxxx//
	122	)))
	123
	124	(% class="box infomessage" %)
	125	(((
	126	with password: //dragino+dragino//
	127	You can use a PC to connect to this Wi-Fi network. The PC will get an IP address 10.130.1.xxx and the HP0D has the default IP 10.130.1.1
	128	)))
	129
	130
	131	[[image:1651804397792-591.png\|\|height="386" width="733"]]
	132
	133
174.2	134
131.1	135	=== 2.1.2 Connect via HP0D hostname ===
	136
174.2	137
131.1	138	Connect the HP0D Ethernet port to your router and HP0D will obtain an IP address. If your PC(Windows/Mac/Ubuntu) connects to the same network with the HP0D, you can access the HP0D Web-UI via HP0D’s hostname.
	139
	140	Like: (% class="mark" %)__//http:~/~/dragino-4ba54a//__
	141
	142
	143	[[image:1651804629009-699.png]]
	144
174.2	145
	146
131.1	147	=== 2.1.3 Connect via Ethernet Port ===
	148
174.2	149
131.1	150	//Connect the HP0D Ethernet port to your router and HP0D will obtain an IP address from your router. In the router’s management portal, you should be able to find what IP address the router has assigned to the HP0D.//
	151
	152
	153	//If you get the IP address from the router, like: (% class="mark" %)10.130.2.42(%%), you can use this IP address to connect the WEB UI or SSH access of HP0D.//
	154
	155
	156	[[image:1651804782523-623.png]]
	157
	158
174.2	159
131.1	160	== 2.2 Generate QR Code ==
	161
	162
	163	(((
174.3	164	//Go to (% style="color:#037691" %)Miner ~-~-> QR Generate(%%), input your Helium Wallet Address, and click Generate.//
131.1	165	)))
	166
	167	(((
174.3	168	(% style="color:red" %)//Note: After onboarding, this wallet will become the owner of this hotspot.//
131.1	169
	170
	171	)))
	172
	173	[[image:image-20220506140312-1.png\|\|height="435" width="438"]]
	174
	175
174.2	176
131.1	177	== 2.3 Onboarding Hotspot ==
	178
	179
	180	(((
	181	//1. Download the Helium Hotspot APP from the Apple or Google Play store.//
	182	)))
	183
	184	(((
174.2	185	(% style="color:red" %)//Note: the APP version needs to be greater than 3.11.//
131.1	186
	187
	188	)))
	189
	190	(((
174.2	191	//2. To add a hotspot, select (% style="color:blue" %)“Hotspot”(%%). On this tab, click the (% style="color:blue" %)“+ Add Hotspot"(%%) in the mid where choose the (% style="color:blue" %)"DRAGINO Miner HP0D"//
131.1	192
	193
	194	)))
	195
	196	[[image:1651817186037-899.png\|\|height="429" width="206"]] [[image:1651817194458-938.png\|\|height="434" width="203"]]
	197
	198
174.2	199
131.1	200	//3. Scan the QR Code you generated in the previous step.//
	201
	202	[[image:1651828211026-220.png\|\|height="405" width="191"]]
	203
	204
174.2	205
131.1	206	(((
	207	//4. Onboarding your device//
	208	)))
	209
	210	(((
174.10	211	Mobile APP will get info from the onboarding server. If the MAC address doesn't appear, it means the network connection of the mobile to the onboarding server might have an issue.
131.1	212
	213
	214	)))
	215
	216	[[image:image-20220506141159-2.png\|\|height="422" width="202"]] [[image:1651817529289-461.png\|\|height="423" width="199"]]
	217
	218	[[image:1651828250802-391.png\|\|height="421" width="197"]] [[image:1651828262668-768.png\|\|height="416" width="196"]](% style="display:none" %)
	219
	220
	221	5. //Check onboarding status where you can check from mobile~://
	222
	223	[[image:1651828391664-884.png\|\|height="413" width="197"]] [[image:1651828401011-970.png\|\|height="412" width="193"]](% style="display:none" %)
	224
	225
	226	//You can also see the hotspot status in the below link~://
	227
	228	//https:~/~/explorer.helium.com/hotspots/<(% class="mark" %)YOUR_HOTSPORT_KEY(%%)>//
	229
	230	//Example~://
	231
	232
	233	//Green Synced means hotspot works normally.//
	234
	235	[[image:1651828427715-679.png\|\|height="374" width="635"]]
	236
	237
174.4	238
131.1	239	== 2.4 Set the Port Forwarding ==
	240
	241
	242	(((
	243	//Helium Hotspots may not work if the Hotspot is behind a firewall or uses an incompatible NAT type. Other times it may be because of a router configuration or the internet is offline. This article aims to help resolve any issues you may have.//
	244	)))
	245
	246	[[image:1651828514449-658.png]]
	247
	248	(((
	249
	250	)))
	251
	252	(((
174.11	253	(((
174.4	254	(% style="color:red" %)Note: Please refer to more detailed Settings
131.1	255	)))
174.11	256	)))
131.1	257
	258	(((
174.11	259	(((
131.1	260	[[https:~~/~~/docs.helium.com/troubleshooting/network-troubleshooting/>>url:https://docs.helium.com/troubleshooting/network-troubleshooting/]]
	261	)))
174.11	262	)))
131.1	263
	264	(((
174.11	265	(((
131.1	266	[[https:~~/~~/www.youtube.com/watch?v=GKusVC7ovrE>>url:https://www.youtube.com/watch?v=GKusVC7ovrE]]
174.11	267	)))
131.1	268
174.4	269
131.1	270
	271	)))
	272
	273	= 3. Check the configuration of HP0D =
	274
	275	== 3.1 LoRa frequency configuration ==
	276
	277
	278	[[image:1651828687205-178.png\|\|height="323" width="657"]]
	279
	280
174.5	281
131.1	282	== 3.2 Check the LoRaWAN Server Address ==
	283
	284
	285	[[image:image-20220607160428-1.png\|\|height="472" width="654"]]
	286
	287
174.5	288
131.1	289	== 3.2.1 Configure the Secondary LoRaWAN Server ==
	290
174.5	291
131.1	292	[[image:image-20220607161130-2.png\|\|height="501" width="1112"]]
	293
160.1	294
131.1	295	[[image:image-20220607161603-3.png\|\|height="557" width="1113"]]
	296
160.1	297
131.1	298	[[image:image-20220607161812-4.png\|\|height="699" width="1115"]]
	299
	300
	301
	302	== 3.3 Check Miner configuration ==
	303
	304
	305	[[image:image-20220506181408-1.png\|\|height="451" width="513"]]
	306
174.5	307
131.1	308	(((
174.5	309	(% style="color:red" %)//Note: Check the Region and Height, the default height is greater than 1, if it is 1 please Click the mid button of Update, and then wait 10mins to check here.//
131.1	310
	311
174.5	312
131.1	313	== //3.4 Check the Miner state// ==
	314
	315
	316	[[image:image-20220531171836-9.png\|\|height="776" width="1155"]]
	317
	318
174.11	319	(((
	320	(% style="color:red" %)//Note: Absorption status can show whether the hotspot is working properly The p2p network can see how your hotspot is interacting with the surrounding hotspots usually, the nat_type should be '//(% style="color:blue" %)//none'//
	321	)))
131.1	322
	323
	324
	325	)))
	326
	327	= 4. Installation of Antenna =
	328
	329
	330	(((
	331	//HP0D uses Fiber Glass Antenna.//
	332	)))
	333
	334	[[image:1651832158606-882.png]]
	335
	336	(((
	337
	338	)))
	339
	340	(((
174.5	341	//The user needs to connect the antenna cable's SMA connector to the HP03 and connect the N-Type connector to the antenna and install it as below~://
131.1	342	)))
	343
	344	(((
	345	[[image:1651832205608-998.png\|\|height="349" width="198"]]
	346
174.5	347
131.1	348
	349	)))
	350
	351	= 5. SSH Access for Linux console =
	352
	353
	354	//Connect the HP0D Ethernet port to your router and HP0D will obtain an IP address from your router.//
	355
	356	//In the router's management portal, you should be able to find what IP address the router has assigned to the HP0D.//
	357
	358	//You can use this IP or hostname of HP0D to connect the WEB UI or SSH access of HP0D.//
	359
	360	//Make sure your PC and the HP0D are in the same network, the use an SSH tool (such as [[putty>>url:http://www.chiark.greenend.org.uk/~~sgtatham/putty/download.html]]) to access it.//
	361
	362
	363	Below are screenshots:
	364
	365	[[image:image-20220608202027-1.png]]
	366
	367	(((
	368	//IP address: IP address of HP0D or hostname of HP0D ((% class="mark" %)Such as dragino-7df4af(%%))//
	369	)))
	370
	371	(((
	372	//Port: 22//
	373	)))
	374
	375	(((
	376	//User Name: (% style="color:green" %)root//
	377	)))
	378
	379	(((
	380	//Password: (% style="color:green" %)Randomly generated （found on device’s label）//
	381
	382
	383	)))
	384
	385	(((
	386	//After logging in, you will be in the Linux console and can enter commands as shown below.//
	387
	388
	389	)))
	390
	391	[[image:image-20220608202118-2.png]]
	392
	393
174.6	394
131.1	395	= 6. How to change the Wireless function of HP0D =
	396
174.6	397
131.1	398	//The wireless function is configured as AP by default and the web page does not support configuration,//
	399
	400	//if you want to configure it as STA(client)connection mode,//
	401
174.6	402	//you can configure your WiFi info on the (% style="color:blue" %)/Network/WiFi (%%)page.//
131.1	403
	404
174.6	405	(% style="color:red" %)//Note: the wireless state is as AP//
131.1	406
	407	[[image:image-20220531170243-5.png\|\|height="469" width="967"]]
	408
	409
174.6	410
131.1	411	== 6.1 Access WiFi configuration page ==
	412
	413
	414	[[image:image-20220531165803-2.png]]
	415
	416
174.6	417
131.1	418	== 6.2 Enter your WiFi information and save ==
	419
	420
	421	[[image:image-20220531165958-3.png]]
	422
	423
174.6	424
131.1	425	== 6.3 Change the WiFi mode. ==
	426
	427
	428	[[image:image-20220531170131-4.png]]
	429
174.6	430
	431
131.1	432	== 6.4 Wait system to restart ==
	433
	434
	435	[[image:image-20220531170501-7.png]]
	436
	437
174.6	438	(% style="color:red" %)//Note: When the time remaining is finished it will turn to the home page.//
131.1	439
	440
174.6	441
131.1	442	== 6.5 Check the STA state ==
	443
	444
	445	[[image:image-20220531170705-8.png\|\|height="484" width="990"]]
	446
	447
174.6	448
131.1	449	= 7. Trouble Shootings =
	450
	451	== 7.1 How to get a wallet address? ==
	452
	453
	454	//Download the helium Hotspots APP on the Apple or Google Play store to generate your own wallet.//
	455
	456
174.6	457
131.1	458	== 7.2 Onboarding ~-~- Unable to access Web-UI ~-~-> Miner ==
	459
	460
	461	(((
	462	//Users can log in to the HP0D, able to access other Web Pages except for the miner page.//
	463	)))
	464
	465	(((
	466	//If you first boot the device where you need to wait for 10 mins for the initialization connection to the Helium server.//
	467
174.6	468
131.1	469
	470	)))
	471
	472	== 7.3 Onboarding ~-~- Some parameters on the miner page show timeout ==
	473
	474
	475	[[image:image-20220506182042-2.png\|\|height="250" width="516"]]
	476
	477	[[image:1651832455372-647.png\|\|height="224" width="520"]]
	478
	479
	480	//HP0D is establishing a connection to the Helium server and is not finished. And you might see above.//
	481
	482	//It might relate to the network which might be up to 10mins.//
	483
	484
174.6	485
131.1	486	== 7.4 Onboarding – Bad Gateway ==
	487
	488
	489	[[image:1651832583790-633.png]]
	490
	491
	492	//This is caused by the process leading too long which just needs to refresh the page.//
	493
	494
174.6	495
131.1	496	== 7.5 Onboarding ~-~- Why did QR Code generate aways fail? ==
	497
	498
	499	[[image:image-20220506182424-3.png]]
	500
	501
	502	(((
	503	//This may be related to the current block height, if the device is synchronizing to the latest height or if the device block height is much lower than the current height as the above picture like '1 1', the QR code generation may fail.//
	504
174.6	505
131.1	506
	507	)))
	508
	509	== 7.6 Onboarding ~-~- Why is the QR Code not quite the same as the manual? ==
	510
174.6	511
131.1	512	[[image:1651832742262-209.png\|\|height="297" width="365"]]
	513
	514
	515	(((
174.6	516	//Please ensure that you enter the correct wallet address and that your network is up and running, the user can click the button of (% style="color:red" %)‘Clean’(%%) to re-generate the QR Code.//
131.1	517
174.6	518
131.1	519
	520	)))
	521
	522	== 7.7 Onboarding – MAC address is ‘Unknown’ after scan QR Code ==
	523
	524
	525	[[image:1651832811038-780.png\|\|height="462" width="216"]]
	526
	527
	528	(((
174.6	529	//If you see the MAC Address shows the (% style="color:red" %)‘Unknown’(%%) where is due to the provisioning error, please contact us to help you solve it.//
131.1	530
174.6	531
131.1	532
	533	)))
	534
174.6	535	== 7.8 Onboarding – MAC address is being refreshed after scanning the QR Code ==
131.1	536
	537
	538	(((
	539	//After scanning the QR Code, Mobile APP will connect to the Helium onboarding server and provide the public key/ wallet address to the onboarding server. The server will return the match MAC address for this hotspot.//
	540
	541
	542	)))
	543
	544	(((
174.6	545	//If you don't see the MAC address, make sure your mobile has a good internet connection.//
131.1	546	)))
	547
	548	[[image:1651832880009-473.png]]
	549
	550
	551
174.6	552	== 7.9 HP0D Web ~-~-> Miner ~-~-> Version shows ‘short’ ==
131.1	553
174.6	554
131.1	555	//This is caused by the server connection delay, which does not affect the regular use.//
	556
	557	[[image:1651832959907-357.png]]
	558
	559
174.6	560
131.1	561	== 7.10 Mobile APP crash after scanning the QR Code? ==
	562
	563
	564	* //Make sure you have input the correct Wallet address to generate QR Code.//
	565	* //Make sure your mobile app uses the same wallet address as the one to generate QR Code.//
174.6	566	* //Make sure your mobile app's relevant permission is enabled.//
131.1	567	* //Known: The Android 11 version may cause this kind of issue.//
	568
	569	== 7.11 Why the frequency/region is not the same as what I purchased? ==
	570
	571
	572	(((
	573	//Each HP0D is inspected and configured prior to shipping.//
	574	)))
	575
	576	(((
	577	//If your HP0D Web-UI – Miner region is not the same as the shell labels, please contact our support team that will solve this issue for you.//
	578
174.6	579
131.1	580
	581	)))
	582
	583	== 7.12 Can use the frequency to a region where is no support? ==
	584
	585
	586	(((
	587	//Please make sure that the region supports this frequency, you can confirm the appropriate frequency through this link://
	588	)))
	589
	590	(((
	591	[[https:~~/~~/docs.helium.com/lorawan-on-helium/frequency-plans>>url:https://docs.helium.com/lorawan-on-helium/frequency-plans]]
	592
174.6	593
131.1	594
	595	)))
	596
	597	== 7.13 Can change the frequency of the HP0D Miner? ==
	598
	599
	600	//We do not recommend doing this, it may damage your device//
	601
	602
174.6	603
131.1	604	== 7.14 Low Reward and not transmit issue ==
	605
	606
	607	//We had released the 0524 version for the miner, Users can check the miner version in the HP0D web UI.//
	608
	609	//If it is lower than the 0524 version, users can manually upgrade it via the 'draginoups' command in the HP0D's CLI.//
	610
	611	[[image:image-20220527114519-1.png\|\|height="579" width="851"]]
	612
	613
174.6	614
131.1	615	== 7.15 Why is my miner version not the latest ==
	616
	617
	618	//By default, as soon as a new version of helium is released, we will push the upgrade the same day.//
	619
	620	//However, the download and upgrade may fail due to the network.//
	621
150.1	622	You can reboot your hotspot where the hotspot will try to upgrade when per booting.
140.1	623
131.1	624
150.1	625	//and We offer manual check methods://
131.1	626
150.1	627	// Use the "draginoups" command to check//
140.1	628
	629
174.6	630	(% style="color:red" %)//Note: How to access the hotspot CLI refer to ( Such as ////[[Step 5.>>url:http://8.211.40.43/xwiki/bin/view/Main/User%20Manual%20for%20All%20Gateway%20models/HP0D#H5.SSHAccessforLinuxconsole]] )//
141.1	631
174.6	632
131.1	633	[[image:image-20220601101358-1.png]]
	634
	635
	636
145.2	637	== 7.16 Why is my miner running down? ==
	638
174.6	639
145.2	640	//the default, the Miner is managed by docker.//
	641
	642	//If you find the miner is offline where the miner is running down.//
	643
	644
	645	What You can do?
	646
174.6	647	(% style="color:blue" %)1. Reboot the hotspot and check again.
145.2	648
149.1	649	//Usually, if the miner is just down, then a reboot is the quickest way//
145.2	650
	651
174.6	652	(% style="color:blue" %)2. Reinstall the Miner manually.
145.2	653
149.1	654	//If rebooting does not solve the problem you can reinstall MINER by one of the following methods//
145.2	655
149.1	656	1). There is an update button in the middle of the miner page, click this button and then the miner will be reinstalled.
	657
	658
174.6	659	2). Run the (% style="color:red" %)"//minerup updat//e"(%%) command to reinstall the miner
149.1	660
	661
	662
145.2	663	[[image:image-20220610094825-2.png\|\|height="457" width="835"]]
	664
174.6	665
145.2	666	[[image:image-20220610094755-1.png\|\|height="706" width="834"]]
	667
	668
174.6	669
163.1	670	== 7.17 More commands for debugging. ==
145.2	671
	672
148.1	673	I'm trapped somewhere, what can I do first?
	674
	675
	676	//dragino provides a method of self-testing//
	677
	678	//1.) Is Hotspot's Miner running?//
	679
	680	//2). Is the miner version up to date?//
	681
	682	//3). Is the height gap between local height and remote height kept within 100//
	683
	684
174.6	685	(% style="color:red" %)//Note: You can find the above three points on the Miner page, and If you are familiar with the Linux command line you can use the following command//
148.1	686
	687
147.1	688	(% class="box infomessage" %)
	689	(((
	690	minerup update #~-~-> reinstall miner but not clearing memory
	691	minerup flush #~-~-> reinstall miner and clear memory
	692	minerup snap #~-~-> load a snap_short to sync the block height
148.1	693	minerup gap #~-~-> check the height between local and remote.
	694	draginoup #~-~-> check the miner version gap between local and remote.
155.1	695
	696
	697	doker ps #~-~-> show the miner running state
	698	miner versions #~-~-> show the miner version
147.1	699	)))
	700
	701
174.6	702
161.1	703	== 7.18 Why does my hotspot not have some of the features described in this WiKi ==
147.1	704
161.1	705
	706	//This is the result of the OTA not being updated in time//
	707
	708	//You can reboot your hotspot or upgrade these packages manually.//
	709
	710
	711	(% class="box infomessage" %)
	712	(((
	713	apt update
	714	apt install dragino*
	715	)))
	716
	717
174.6	718
155.1	719	= 8. How to flash a new OS for the hotspot, the hotspot's setting will be factory settings =
131.1	720
174.6	721
131.1	722	The hotspot is based on the Rpi-4B so the OS has been installed on the SD card.
	723
	724	So you have to re-flash the image into the SD card.
	725
174.6	726	(% style="background-color:yellow" %)Warning: Do not reset unless necessary
131.1	727
139.1	728
174.6	729	(% style="color:blue" %)//Preparations://
131.1	730
	731	1. //Open the HP0D shell, and take out the SD card from the Raspberry PI 4B (Make sure the SD card is empty )//
	732
	733	2. //Download the OS image~: ( Such as [[draginohp0d-1.9img>>url:http://repo.dragino.com/release/hp0d-image/draginohp0d-1.9.img]] )//
	734
	735	3. //A card reader device//
	736
	737	4. //A Flash software tool ( Such as [[balenaEtcher>>url:https://www.balena.io/etcher/]] )//
	738
	739	5. //SD Card [[formatter>>url:http://repo.dragino.com/release/tool/PanasonicSDFormatter.zip]]//
	740
	741
174.6	742	(% style="color:blue" %)HP0D's enclosure
158.1	743
	744
	745	[[image:image-20220615204902-1.png\|\|height="633" width="918"]]
	746
	747
	748	[[image:image-20220615204917-2.png\|\|height="1038" width="922"]]
	749
	750
	751
174.6	752	=== (% style="color:blue" %)Step 1. Formatting the SD Card(%%) ===
131.1	753
	754
	755	[[image:image-20220609111027-9.png]]
	756
	757
174.7	758
174.6	759	=== (% style="color:blue" %)Step 2. Select the OS image (%%) ===
131.1	760
	761
	762	[[image:image-20220609104907-8.png]]
	763
	764
174.7	765
174.6	766	=== (% style="color:blue" %)Step 3. Select the target (%%) ===
131.1	767
	768
	769	[[image:image-20220609104637-2.png]]
	770
	771	[[image:image-20220609104701-3.png]]
	772
	773
174.7	774
174.6	775	=== (% style="color:blue" %)Step 4. Flash start(%%) ===
131.1	776
	777
	778	[[image:image-20220609104727-4.png]]
	779
	780	[[image:image-20220609104741-5.png]]
	781
	782
174.6	783	=== (% style="color:blue" %)Flash Complete(%%) ===
131.1	784
	785
	786	[[image:image-20220609104415-1.png]]
	787
	788
	789	== Step 4. Re-install the SD card into the hotspot and boot it ==
	790
	791
174.6	792
131.1	793	== Step 5. Configure the correct region for the miner ==
	794
174.6	795
131.1	796	by the default, the factory settings apply to the US915.
	797
	798	if your region is not the US915, you have to configure the correct region for the miner.
	799
	800
	801	Access the hotspot CLI, and run these Linux commands
	802
	803
132.1	804	(% class="box infomessage" %)
	805	(((
131.1	806	~#~##update the software of dragino
	807
	808	apt update
	809
	810	apt install dragino*
132.1	811	)))
131.1	812
	813	[[image:image-20220609150452-2.png\|\|height="348" width="909"]]
	814
	815
	816
132.1	817	(% class="box infomessage" %)
	818	(((
131.1	819	~#~##configure the correct region for the miner and update it
	820
138.1	821	uci set miner.general.region=<Region; Such as AS923_1/AU915/US915/EU868/IN865>
131.1	822
	823	uci commit miner
	824
	825	minerup update
132.1	826	)))
131.1	827
137.1	828	[[image:image-20220609151513-5.png]]
131.1	829
	830
174.6	831
132.1	832	(% class="box infomessage" %)
	833	(((
131.1	834	~#~##check the miner version
	835
	836	draginoups
132.1	837	)))
131.1	838
135.1	839	[[image:image-20220609151419-3.png]]
131.1	840
143.1	841
174.6	842
143.1	843	(% class="box infomessage" %)
	844	(((
	845	~#~##unblock the function of wireless
	846	rfkill unblock wlan
	847	uci set wireless.general.mode=ap
	848	uci commit wireless
	849	)))
	850
	851	[[image:image-20220609161204-1.png]]
	852
131.1	853
160.1	854
174.1	855	= 9. How does the HP0D access to the network via a USB 4G Dongle =
160.1	856
174.6	857
172.1	858	We have reserved enough space inside the HP0D to use a USB 4G Dongle,
	859
	860	so you can install a USB 4G Dongle in order for the hotspot to access the network via 4G.
	861
	862
174.6	863	(% style="color:green" %)//Preparations://
172.1	864
	865	//1). A USB 4G Dongle, Such as HUAWEI E3327,ZTE...//
	866
	867	//2). A Sim card that can access the 4g network.//
	868
	869	//3). open the hotspot's shell.//
	870
	871
174.6	872
172.1	873	== 9.1. Open the HP0D shell and access the USB 4G Dongle into the Rpi. ==
	874
174.6	875
172.1	876	[[image:image-20220627153334-2.png]]
	877
	878
174.6	879
172.1	880	== 9.2. Checking the USB 4G Dongle network ==
	881
174.6	882
172.1	883	We have installed drivers for common USB 4G Dongle,
	884
	885	and managed by NetworkManager, once hp0d detects an available USB 4G Dongle it will try to dial up the range network
	886
	887
174.6	888	//HUAWEI-E3327//
172.1	889
	890	[[image:image-20220627154526-9.png\|\|height="762" width="725"]]
	891
	892
	893
174.6	894	//ZTE//
	895
172.1	896	[[image:image-20220627154201-5.png]]
	897
	898
	899
	900	= 10. PoE introduction =
	901
	902
174.6	903	//The HP0D is use the (% style="color:blue" %)IEEE 802.3 af compliant PoE port(%%) (input 44 ~~ 57 v, output 12V)//
160.1	904
161.1	905	//So you can use the PoE //switches// or PoE injector to power the device.//
160.1	906
	907
174.6	908	(((
	909	(% style="color:red" %)Note: The RJ45 Indicator light only represents the PoE power supply, so when you use DC to power the hotspot and the RJ45 indicator light is off ~-~--> this is normal
	910	)))
160.1	911
	912
174.6	913	(% style="background-color:yellow" %)Wiring schematic:
160.1	914
	915	[[image:image-20220616143347-1.png]]
	916
	917
	918
	919
173.1	920	= 11. OTA Version Info =
160.1	921
174.6	922
131.1	923	== When does the OTA update happen? ==
	924
	925
	926	//HP0D will check OTA update on a) Every Booting. b) Every Night. Below is the OTA update version info//
	927
174.6	928
	929
131.1	930	== # 2022/05/14 ==
	931
	932
	933	1. //Update to the latest miner version: miner-arm64_2022.05.13.0_GA//
	934	1. //Add postinst after auto-update//
	935	1. //Add Miner version mark.//
	936	1. //Add fast sync if miner GAP is large//
	937
152.1	938	== # 2022/05/18 ==
	939
	940
	941	1. //Update minerup to speed up synchronized blocks//
	942
131.1	943	== # 2022/05/24 ==
	944
151.1	945
152.1	946	1. //Update to the latest miner version: miner-arm64_2022.05.24.0_GA//
131.1	947
151.1	948	== # 2022/05/31 ==
131.1	949
174.6	950
152.1	951	1. //Add WiFi STA icon display//
	952	1. //Optimize AP icon display//
	953	1. //Optimize home icon display//
	954	1. //Fix for Miner icon URL bug//
	955	1. //Add the secondary server configuration//
151.1	956
173.1	957	= 12. Supports =
131.1	958
174.6	959
131.1	960	(((
	961	//If you are experiencing issues and can’t solve them, you can send mail to [[support@dragino.com>>mailto:support@dragino.com]].//
	962	)))
	963
	964	(((
	965	//With your question as detailed as possible. We will reply and help you in the shortest.//
	966
174.6	967
131.1	968
	969	)))
	970
173.1	971	= 13. Order Info =
131.1	972
	973
174.6	974	(% style="color:blue" %)HP0D-XXX
131.1	975
174.6	976	(% style="color:blue" %)XXX(%%): Frequency Band
131.1	977
174.6	978	* (% style="color:red" %)AS923(%%): LoRaWAN AS923 band
	979	* (% style="color:red" %)AU915(%%): LoRaWAN AU915 band
	980	* (% style="color:red" %)EU868(%%): LoRaWAN EU868 band
	981	* (% style="color:red" %)KR920(%%): LoRaWAN KR920 band
	982	* (% style="color:red" %)US915(%%): LoRaWAN US915 band
	983	* (% style="color:red" %)IN865(%%): LoRaWAN IN865 band
	984
173.1	985	= 14. Manufacturer Info =
131.1	986
174.6	987
131.1	988	(((
	989	Shenzhen Dragino Technology Development co. LTD
	990	)))
	991
	992	(((
	993	Room 202, Block B, BCT Incubation Bases (BaoChengTai), No.8 CaiYunRoad
	994	)))
	995
	996	(((
	997	Longcheng Street, LongGang District; Shenzhen 518116, China
	998
	999
	1000
	1001	)))
	1002
173.1	1003	= 15. FCC Warning =
131.1	1004
174.6	1005
131.1	1006	(((
	1007	This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
	1008	)))
	1009
	1010	(((
	1011	~-~- Reorient or relocate the receiving antenna.
	1012	)))
	1013
	1014	(((
	1015	~-~- Increase the separation between the equipment and receiver.
	1016	)))
	1017
	1018	(((
	1019	~-~- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
	1020	)))
	1021
	1022	(((
	1023	~-~- Consult the dealer or an experienced radio/TV technician for help.
	1024	)))
	1025
	1026	(((
	1027	Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
	1028	)))
	1029
	1030	(((
	1031	The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
	1032	)))

Wiki source code of HP0D Full Hotspot for Helium User Manual

Applications

Navigation