Wiki source code of HP0D Full Hotspot for Helium User Manual

Version 174.11 by Xiaoling on 2022/07/27 17:06

version	line-number	content
131.1	1	(% style="text-align:center" %)
	2	[[image:1651802206983-860.png\|\|height="427" width="398"]]
	3
	4
	5	(((
174.2	6
131.1	7
	8
	9	)))
	10
	11	Table of Contents：
	12
	13	{{toc/}}
	14
	15
	16	= 1. Introduction =
	17
	18	== 1.1 What is HP0D ==
	19
174.2	20
131.1	21	(((
	22	The HP0D is an outdoor LoRaWAN Gateway. It lets you bridge LoRa wireless network to an IP network via WiFi,Ethernet, optional 3G or 4G. The LoRa wireless allows users to send data and reach extremely long ranges at low data rates.
	23	)))
	24
	25	(((
	26	HP0D has passed Helium Full Hotspot Approval. It supports the (% style="color:#037691" %) miner feature from Helium (% style="color:black" %) and has a built-in ATECC608 encryption chip. It can be used as a Helium Full Hotspot for the project. It also supports Semtech packet forwarder and LoRaWAN Station connection, it is fully compatible with LoRaWAN protocol.HP0D supports two LoRaWAN servers at the same time, (% style="color:#037691" %)users can use HP0D for helium mining and connects max 2 x LoRaWAN servers at the same time.
	27	)))
	28
	29	(((
	30	(% style="color:#037691" %)Dragino already paid HP0D $40 onboarding cost and $10 location cost for each HP0D. (% style="color:black" %)It is ready to use for Helium, user only needs to input HNT wallet address and use QR Code to onboarding HP0D when it arrives.
	31	)))
	32
	33	(((
	34	HP0D has pre-configured standard LoRaWAN frequency bands to use for different countries. Users can also customize the frequency bands to use in their own LoRaWAN network.
174.2	35
	36
131.1	37	)))
	38
	39	== 1.2 Specifications ==
	40
	41	~ Hardware System:
	42	Linux Part:
	43
	44	* Raspberry Pi 4
	45
	46	~ Interface:
	47
	48	* 10M/100M RJ45 Ports x 1
	49	* LoRaWAN Wireless
	50	* Power Input: 12V 2A, DC
	51
	52	~ Operating Condition:
	53
	54	* Work Temperature: -20 ~~ 65°C
	55	* Storage Temperature: -20 ~~ 65°C
	56	* Power Input: 12V 2A, DC
	57
174.9	58
	59
131.1	60	== 1.3 Features ==
	61
	62	* Open-Source Linux system
	63	* RPi4 with 2G /4G or 8G RAM
	64	* Managed by Web GUI, SSH via Internet
	65	* Support Semtech UDP packet forwarder
	66	* Support LoRaWAN Station Connection
	67	* Support Helium Miner
	68	* External fiberglass antenna
	69	* Firmware OTA
	70	* 802.3af PoE
	71	* Lighting Protection
	72	* Remote Monitoring
	73	* Support Helium LoRaWAN server and secondary LoRaWAN server
	74	* Include prepaid $40 onboarding cost and $10 location cost.
	75	* [[Remote.it remote management>>url:https://wiki.dragino.com/index.php?title=Reverse_SSH_Access#Use_Remote.it_service]].
	76
174.9	77
	78
131.1	79	== 1.4 Label info and login name ==
	80
174.2	81
131.1	82	[[image:1651803959860-394.png\|\|height="500" width="375"]]
	83
	84
	85
	86	=== 1.4.1 Label information: ===
	87
174.2	88
131.1	89	Device hostname: (% class="mark" %)dragino-xxxxxx(%%)
	90	Band: (% class="mark" %)US915/AU915/AS923_1-AS923_4/KR920/EU868/IN865/RU864(%%)
	91	Miner animal name: (% class="mark" %)xxx-xxx-xxx(%%)
	92	Miner address: (% class="mark" %)12xxxxxx(%%)
	93	Eth MAC address: (% class="mark" %)A8: 40: 41: EF: FE: CD(%%)
	94	Login: (% class="mark" %)root/d59f2d5b (the root is the Login account for the Web-UI and SSH.)(%%)
	95	SN: (% class="mark" %)device serial number.
	96
	97
174.2	98
131.1	99	= 2. Quick Start & Onboarding =
	100
174.2	101
131.1	102	The HP0D is configured as a Wi-Fi Access Point by factory default. You can access and configure the HPD after connecting to its Wi-Fi network, or via its WAN Ethernet port.
	103
	104
	105	== 2.1 Connect HP0D Web UI ==
	106
	107
174.3	108	=== 2.1.1 via HP0D's Access Point ===
	109
	110
131.1	111	At the first boot of HP0D, it will auto-generate a Wi-Fi network
	112
	113
	114	[[image:1651804327535-321.png\|\|height="325" width="199"]]
	115
	116
	117	(% class="box infomessage" %)
	118	(((
	119	called : //HPD-dragino-xxxxxx//
	120	)))
	121
	122	(% class="box infomessage" %)
	123	(((
	124	with password: //dragino+dragino//
	125	You can use a PC to connect to this Wi-Fi network. The PC will get an IP address 10.130.1.xxx and the HP0D has the default IP 10.130.1.1
	126	)))
	127
	128
	129	[[image:1651804397792-591.png\|\|height="386" width="733"]]
	130
	131
174.2	132
131.1	133	=== 2.1.2 Connect via HP0D hostname ===
	134
174.2	135
131.1	136	Connect the HP0D Ethernet port to your router and HP0D will obtain an IP address. If your PC(Windows/Mac/Ubuntu) connects to the same network with the HP0D, you can access the HP0D Web-UI via HP0D’s hostname.
	137
	138	Like: (% class="mark" %)__//http:~/~/dragino-4ba54a//__
	139
	140
	141	[[image:1651804629009-699.png]]
	142
174.2	143
	144
131.1	145	=== 2.1.3 Connect via Ethernet Port ===
	146
174.2	147
131.1	148	//Connect the HP0D Ethernet port to your router and HP0D will obtain an IP address from your router. In the router’s management portal, you should be able to find what IP address the router has assigned to the HP0D.//
	149
	150
	151	//If you get the IP address from the router, like: (% class="mark" %)10.130.2.42(%%), you can use this IP address to connect the WEB UI or SSH access of HP0D.//
	152
	153
	154	[[image:1651804782523-623.png]]
	155
	156
174.2	157
131.1	158	== 2.2 Generate QR Code ==
	159
	160
	161	(((
174.3	162	//Go to (% style="color:#037691" %)Miner ~-~-> QR Generate(%%), input your Helium Wallet Address, and click Generate.//
131.1	163	)))
	164
	165	(((
174.3	166	(% style="color:red" %)//Note: After onboarding, this wallet will become the owner of this hotspot.//
131.1	167
	168
	169	)))
	170
	171	[[image:image-20220506140312-1.png\|\|height="435" width="438"]]
	172
	173
174.2	174
131.1	175	== 2.3 Onboarding Hotspot ==
	176
	177
	178	(((
	179	//1. Download the Helium Hotspot APP from the Apple or Google Play store.//
	180	)))
	181
	182	(((
174.2	183	(% style="color:red" %)//Note: the APP version needs to be greater than 3.11.//
131.1	184
	185
	186	)))
	187
	188	(((
174.2	189	//2. To add a hotspot, select (% style="color:blue" %)“Hotspot”(%%). On this tab, click the (% style="color:blue" %)“+ Add Hotspot"(%%) in the mid where choose the (% style="color:blue" %)"DRAGINO Miner HP0D"//
131.1	190
	191
	192	)))
	193
	194	[[image:1651817186037-899.png\|\|height="429" width="206"]] [[image:1651817194458-938.png\|\|height="434" width="203"]]
	195
	196
174.2	197
131.1	198	//3. Scan the QR Code you generated in the previous step.//
	199
	200	[[image:1651828211026-220.png\|\|height="405" width="191"]]
	201
	202
174.2	203
131.1	204	(((
	205	//4. Onboarding your device//
	206	)))
	207
	208	(((
174.10	209	Mobile APP will get info from the onboarding server. If the MAC address doesn't appear, it means the network connection of the mobile to the onboarding server might have an issue.
131.1	210
	211
	212	)))
	213
	214	[[image:image-20220506141159-2.png\|\|height="422" width="202"]] [[image:1651817529289-461.png\|\|height="423" width="199"]]
	215
	216	[[image:1651828250802-391.png\|\|height="421" width="197"]] [[image:1651828262668-768.png\|\|height="416" width="196"]](% style="display:none" %)
	217
	218
	219	5. //Check onboarding status where you can check from mobile~://
	220
	221	[[image:1651828391664-884.png\|\|height="413" width="197"]] [[image:1651828401011-970.png\|\|height="412" width="193"]](% style="display:none" %)
	222
	223
	224	//You can also see the hotspot status in the below link~://
	225
	226	//https:~/~/explorer.helium.com/hotspots/<(% class="mark" %)YOUR_HOTSPORT_KEY(%%)>//
	227
	228	//Example~://
	229
	230
	231	//Green Synced means hotspot works normally.//
	232
	233	[[image:1651828427715-679.png\|\|height="374" width="635"]]
	234
	235
174.4	236
131.1	237	== 2.4 Set the Port Forwarding ==
	238
	239
	240	(((
	241	//Helium Hotspots may not work if the Hotspot is behind a firewall or uses an incompatible NAT type. Other times it may be because of a router configuration or the internet is offline. This article aims to help resolve any issues you may have.//
	242	)))
	243
	244	[[image:1651828514449-658.png]]
	245
	246	(((
	247
	248	)))
	249
	250	(((
174.11	251	(((
174.4	252	(% style="color:red" %)Note: Please refer to more detailed Settings
131.1	253	)))
174.11	254	)))
131.1	255
	256	(((
174.11	257	(((
131.1	258	[[https:~~/~~/docs.helium.com/troubleshooting/network-troubleshooting/>>url:https://docs.helium.com/troubleshooting/network-troubleshooting/]]
	259	)))
174.11	260	)))
131.1	261
	262	(((
174.11	263	(((
131.1	264	[[https:~~/~~/www.youtube.com/watch?v=GKusVC7ovrE>>url:https://www.youtube.com/watch?v=GKusVC7ovrE]]
174.11	265	)))
131.1	266
174.4	267
131.1	268
	269	)))
	270
	271	= 3. Check the configuration of HP0D =
	272
	273	== 3.1 LoRa frequency configuration ==
	274
	275
	276	[[image:1651828687205-178.png\|\|height="323" width="657"]]
	277
	278
174.5	279
131.1	280	== 3.2 Check the LoRaWAN Server Address ==
	281
	282
	283	[[image:image-20220607160428-1.png\|\|height="472" width="654"]]
	284
	285
174.5	286
131.1	287	== 3.2.1 Configure the Secondary LoRaWAN Server ==
	288
174.5	289
131.1	290	[[image:image-20220607161130-2.png\|\|height="501" width="1112"]]
	291
160.1	292
131.1	293	[[image:image-20220607161603-3.png\|\|height="557" width="1113"]]
	294
160.1	295
131.1	296	[[image:image-20220607161812-4.png\|\|height="699" width="1115"]]
	297
	298
	299
	300	== 3.3 Check Miner configuration ==
	301
	302
	303	[[image:image-20220506181408-1.png\|\|height="451" width="513"]]
	304
174.5	305
131.1	306	(((
174.5	307	(% style="color:red" %)//Note: Check the Region and Height, the default height is greater than 1, if it is 1 please Click the mid button of Update, and then wait 10mins to check here.//
131.1	308
	309
174.5	310
131.1	311	== //3.4 Check the Miner state// ==
	312
	313
	314	[[image:image-20220531171836-9.png\|\|height="776" width="1155"]]
	315
	316
174.11	317	(((
	318	(% style="color:red" %)//Note: Absorption status can show whether the hotspot is working properly The p2p network can see how your hotspot is interacting with the surrounding hotspots usually, the nat_type should be '//(% style="color:blue" %)//none'//
	319	)))
131.1	320
	321
	322
	323	)))
	324
	325	= 4. Installation of Antenna =
	326
	327
	328	(((
	329	//HP0D uses Fiber Glass Antenna.//
	330	)))
	331
	332	[[image:1651832158606-882.png]]
	333
	334	(((
	335
	336	)))
	337
	338	(((
174.5	339	//The user needs to connect the antenna cable's SMA connector to the HP03 and connect the N-Type connector to the antenna and install it as below~://
131.1	340	)))
	341
	342	(((
	343	[[image:1651832205608-998.png\|\|height="349" width="198"]]
	344
174.5	345
131.1	346
	347	)))
	348
	349	= 5. SSH Access for Linux console =
	350
	351
	352	//Connect the HP0D Ethernet port to your router and HP0D will obtain an IP address from your router.//
	353
	354	//In the router's management portal, you should be able to find what IP address the router has assigned to the HP0D.//
	355
	356	//You can use this IP or hostname of HP0D to connect the WEB UI or SSH access of HP0D.//
	357
	358	//Make sure your PC and the HP0D are in the same network, the use an SSH tool (such as [[putty>>url:http://www.chiark.greenend.org.uk/~~sgtatham/putty/download.html]]) to access it.//
	359
	360
	361	Below are screenshots:
	362
	363	[[image:image-20220608202027-1.png]]
	364
	365	(((
	366	//IP address: IP address of HP0D or hostname of HP0D ((% class="mark" %)Such as dragino-7df4af(%%))//
	367	)))
	368
	369	(((
	370	//Port: 22//
	371	)))
	372
	373	(((
	374	//User Name: (% style="color:green" %)root//
	375	)))
	376
	377	(((
	378	//Password: (% style="color:green" %)Randomly generated （found on device’s label）//
	379
	380
	381	)))
	382
	383	(((
	384	//After logging in, you will be in the Linux console and can enter commands as shown below.//
	385
	386
	387	)))
	388
	389	[[image:image-20220608202118-2.png]]
	390
	391
174.6	392
131.1	393	= 6. How to change the Wireless function of HP0D =
	394
174.6	395
131.1	396	//The wireless function is configured as AP by default and the web page does not support configuration,//
	397
	398	//if you want to configure it as STA(client)connection mode,//
	399
174.6	400	//you can configure your WiFi info on the (% style="color:blue" %)/Network/WiFi (%%)page.//
131.1	401
	402
174.6	403	(% style="color:red" %)//Note: the wireless state is as AP//
131.1	404
	405	[[image:image-20220531170243-5.png\|\|height="469" width="967"]]
	406
	407
174.6	408
131.1	409	== 6.1 Access WiFi configuration page ==
	410
	411
	412	[[image:image-20220531165803-2.png]]
	413
	414
174.6	415
131.1	416	== 6.2 Enter your WiFi information and save ==
	417
	418
	419	[[image:image-20220531165958-3.png]]
	420
	421
174.6	422
131.1	423	== 6.3 Change the WiFi mode. ==
	424
	425
	426	[[image:image-20220531170131-4.png]]
	427
174.6	428
	429
131.1	430	== 6.4 Wait system to restart ==
	431
	432
	433	[[image:image-20220531170501-7.png]]
	434
	435
174.6	436	(% style="color:red" %)//Note: When the time remaining is finished it will turn to the home page.//
131.1	437
	438
174.6	439
131.1	440	== 6.5 Check the STA state ==
	441
	442
	443	[[image:image-20220531170705-8.png\|\|height="484" width="990"]]
	444
	445
174.6	446
131.1	447	= 7. Trouble Shootings =
	448
	449	== 7.1 How to get a wallet address? ==
	450
	451
	452	//Download the helium Hotspots APP on the Apple or Google Play store to generate your own wallet.//
	453
	454
174.6	455
131.1	456	== 7.2 Onboarding ~-~- Unable to access Web-UI ~-~-> Miner ==
	457
	458
	459	(((
	460	//Users can log in to the HP0D, able to access other Web Pages except for the miner page.//
	461	)))
	462
	463	(((
	464	//If you first boot the device where you need to wait for 10 mins for the initialization connection to the Helium server.//
	465
174.6	466
131.1	467
	468	)))
	469
	470	== 7.3 Onboarding ~-~- Some parameters on the miner page show timeout ==
	471
	472
	473	[[image:image-20220506182042-2.png\|\|height="250" width="516"]]
	474
	475	[[image:1651832455372-647.png\|\|height="224" width="520"]]
	476
	477
	478	//HP0D is establishing a connection to the Helium server and is not finished. And you might see above.//
	479
	480	//It might relate to the network which might be up to 10mins.//
	481
	482
174.6	483
131.1	484	== 7.4 Onboarding – Bad Gateway ==
	485
	486
	487	[[image:1651832583790-633.png]]
	488
	489
	490	//This is caused by the process leading too long which just needs to refresh the page.//
	491
	492
174.6	493
131.1	494	== 7.5 Onboarding ~-~- Why did QR Code generate aways fail? ==
	495
	496
	497	[[image:image-20220506182424-3.png]]
	498
	499
	500	(((
	501	//This may be related to the current block height, if the device is synchronizing to the latest height or if the device block height is much lower than the current height as the above picture like '1 1', the QR code generation may fail.//
	502
174.6	503
131.1	504
	505	)))
	506
	507	== 7.6 Onboarding ~-~- Why is the QR Code not quite the same as the manual? ==
	508
174.6	509
131.1	510	[[image:1651832742262-209.png\|\|height="297" width="365"]]
	511
	512
	513	(((
174.6	514	//Please ensure that you enter the correct wallet address and that your network is up and running, the user can click the button of (% style="color:red" %)‘Clean’(%%) to re-generate the QR Code.//
131.1	515
174.6	516
131.1	517
	518	)))
	519
	520	== 7.7 Onboarding – MAC address is ‘Unknown’ after scan QR Code ==
	521
	522
	523	[[image:1651832811038-780.png\|\|height="462" width="216"]]
	524
	525
	526	(((
174.6	527	//If you see the MAC Address shows the (% style="color:red" %)‘Unknown’(%%) where is due to the provisioning error, please contact us to help you solve it.//
131.1	528
174.6	529
131.1	530
	531	)))
	532
174.6	533	== 7.8 Onboarding – MAC address is being refreshed after scanning the QR Code ==
131.1	534
	535
	536	(((
	537	//After scanning the QR Code, Mobile APP will connect to the Helium onboarding server and provide the public key/ wallet address to the onboarding server. The server will return the match MAC address for this hotspot.//
	538
	539
	540	)))
	541
	542	(((
174.6	543	//If you don't see the MAC address, make sure your mobile has a good internet connection.//
131.1	544	)))
	545
	546	[[image:1651832880009-473.png]]
	547
	548
	549
174.6	550	== 7.9 HP0D Web ~-~-> Miner ~-~-> Version shows ‘short’ ==
131.1	551
174.6	552
131.1	553	//This is caused by the server connection delay, which does not affect the regular use.//
	554
	555	[[image:1651832959907-357.png]]
	556
	557
174.6	558
131.1	559	== 7.10 Mobile APP crash after scanning the QR Code? ==
	560
	561
	562	* //Make sure you have input the correct Wallet address to generate QR Code.//
	563	* //Make sure your mobile app uses the same wallet address as the one to generate QR Code.//
174.6	564	* //Make sure your mobile app's relevant permission is enabled.//
131.1	565	* //Known: The Android 11 version may cause this kind of issue.//
	566
	567	== 7.11 Why the frequency/region is not the same as what I purchased? ==
	568
	569
	570	(((
	571	//Each HP0D is inspected and configured prior to shipping.//
	572	)))
	573
	574	(((
	575	//If your HP0D Web-UI – Miner region is not the same as the shell labels, please contact our support team that will solve this issue for you.//
	576
174.6	577
131.1	578
	579	)))
	580
	581	== 7.12 Can use the frequency to a region where is no support? ==
	582
	583
	584	(((
	585	//Please make sure that the region supports this frequency, you can confirm the appropriate frequency through this link://
	586	)))
	587
	588	(((
	589	[[https:~~/~~/docs.helium.com/lorawan-on-helium/frequency-plans>>url:https://docs.helium.com/lorawan-on-helium/frequency-plans]]
	590
174.6	591
131.1	592
	593	)))
	594
	595	== 7.13 Can change the frequency of the HP0D Miner? ==
	596
	597
	598	//We do not recommend doing this, it may damage your device//
	599
	600
174.6	601
131.1	602	== 7.14 Low Reward and not transmit issue ==
	603
	604
	605	//We had released the 0524 version for the miner, Users can check the miner version in the HP0D web UI.//
	606
	607	//If it is lower than the 0524 version, users can manually upgrade it via the 'draginoups' command in the HP0D's CLI.//
	608
	609	[[image:image-20220527114519-1.png\|\|height="579" width="851"]]
	610
	611
174.6	612
131.1	613	== 7.15 Why is my miner version not the latest ==
	614
	615
	616	//By default, as soon as a new version of helium is released, we will push the upgrade the same day.//
	617
	618	//However, the download and upgrade may fail due to the network.//
	619
150.1	620	You can reboot your hotspot where the hotspot will try to upgrade when per booting.
140.1	621
131.1	622
150.1	623	//and We offer manual check methods://
131.1	624
150.1	625	// Use the "draginoups" command to check//
140.1	626
	627
174.6	628	(% style="color:red" %)//Note: How to access the hotspot CLI refer to ( Such as ////[[Step 5.>>url:http://8.211.40.43/xwiki/bin/view/Main/User%20Manual%20for%20All%20Gateway%20models/HP0D#H5.SSHAccessforLinuxconsole]] )//
141.1	629
174.6	630
131.1	631	[[image:image-20220601101358-1.png]]
	632
	633
	634
145.2	635	== 7.16 Why is my miner running down? ==
	636
174.6	637
145.2	638	//the default, the Miner is managed by docker.//
	639
	640	//If you find the miner is offline where the miner is running down.//
	641
	642
	643	What You can do?
	644
174.6	645	(% style="color:blue" %)1. Reboot the hotspot and check again.
145.2	646
149.1	647	//Usually, if the miner is just down, then a reboot is the quickest way//
145.2	648
	649
174.6	650	(% style="color:blue" %)2. Reinstall the Miner manually.
145.2	651
149.1	652	//If rebooting does not solve the problem you can reinstall MINER by one of the following methods//
145.2	653
149.1	654	1). There is an update button in the middle of the miner page, click this button and then the miner will be reinstalled.
	655
	656
174.6	657	2). Run the (% style="color:red" %)"//minerup updat//e"(%%) command to reinstall the miner
149.1	658
	659
	660
145.2	661	[[image:image-20220610094825-2.png\|\|height="457" width="835"]]
	662
174.6	663
145.2	664	[[image:image-20220610094755-1.png\|\|height="706" width="834"]]
	665
	666
174.6	667
163.1	668	== 7.17 More commands for debugging. ==
145.2	669
	670
148.1	671	I'm trapped somewhere, what can I do first?
	672
	673
	674	//dragino provides a method of self-testing//
	675
	676	//1.) Is Hotspot's Miner running?//
	677
	678	//2). Is the miner version up to date?//
	679
	680	//3). Is the height gap between local height and remote height kept within 100//
	681
	682
174.6	683	(% style="color:red" %)//Note: You can find the above three points on the Miner page, and If you are familiar with the Linux command line you can use the following command//
148.1	684
	685
147.1	686	(% class="box infomessage" %)
	687	(((
	688	minerup update #~-~-> reinstall miner but not clearing memory
	689	minerup flush #~-~-> reinstall miner and clear memory
	690	minerup snap #~-~-> load a snap_short to sync the block height
148.1	691	minerup gap #~-~-> check the height between local and remote.
	692	draginoup #~-~-> check the miner version gap between local and remote.
155.1	693
	694
	695	doker ps #~-~-> show the miner running state
	696	miner versions #~-~-> show the miner version
147.1	697	)))
	698
	699
174.6	700
161.1	701	== 7.18 Why does my hotspot not have some of the features described in this WiKi ==
147.1	702
161.1	703
	704	//This is the result of the OTA not being updated in time//
	705
	706	//You can reboot your hotspot or upgrade these packages manually.//
	707
	708
	709	(% class="box infomessage" %)
	710	(((
	711	apt update
	712	apt install dragino*
	713	)))
	714
	715
174.6	716
155.1	717	= 8. How to flash a new OS for the hotspot, the hotspot's setting will be factory settings =
131.1	718
174.6	719
131.1	720	The hotspot is based on the Rpi-4B so the OS has been installed on the SD card.
	721
	722	So you have to re-flash the image into the SD card.
	723
174.6	724	(% style="background-color:yellow" %)Warning: Do not reset unless necessary
131.1	725
139.1	726
174.6	727	(% style="color:blue" %)//Preparations://
131.1	728
	729	1. //Open the HP0D shell, and take out the SD card from the Raspberry PI 4B (Make sure the SD card is empty )//
	730
	731	2. //Download the OS image~: ( Such as [[draginohp0d-1.9img>>url:http://repo.dragino.com/release/hp0d-image/draginohp0d-1.9.img]] )//
	732
	733	3. //A card reader device//
	734
	735	4. //A Flash software tool ( Such as [[balenaEtcher>>url:https://www.balena.io/etcher/]] )//
	736
	737	5. //SD Card [[formatter>>url:http://repo.dragino.com/release/tool/PanasonicSDFormatter.zip]]//
	738
	739
174.6	740	(% style="color:blue" %)HP0D's enclosure
158.1	741
	742
	743	[[image:image-20220615204902-1.png\|\|height="633" width="918"]]
	744
	745
	746	[[image:image-20220615204917-2.png\|\|height="1038" width="922"]]
	747
	748
	749
174.6	750	=== (% style="color:blue" %)Step 1. Formatting the SD Card(%%) ===
131.1	751
	752
	753	[[image:image-20220609111027-9.png]]
	754
	755
174.7	756
174.6	757	=== (% style="color:blue" %)Step 2. Select the OS image (%%) ===
131.1	758
	759
	760	[[image:image-20220609104907-8.png]]
	761
	762
174.7	763
174.6	764	=== (% style="color:blue" %)Step 3. Select the target (%%) ===
131.1	765
	766
	767	[[image:image-20220609104637-2.png]]
	768
	769	[[image:image-20220609104701-3.png]]
	770
	771
174.7	772
174.6	773	=== (% style="color:blue" %)Step 4. Flash start(%%) ===
131.1	774
	775
	776	[[image:image-20220609104727-4.png]]
	777
	778	[[image:image-20220609104741-5.png]]
	779
	780
174.6	781	=== (% style="color:blue" %)Flash Complete(%%) ===
131.1	782
	783
	784	[[image:image-20220609104415-1.png]]
	785
	786
	787	== Step 4. Re-install the SD card into the hotspot and boot it ==
	788
	789
174.6	790
131.1	791	== Step 5. Configure the correct region for the miner ==
	792
174.6	793
131.1	794	by the default, the factory settings apply to the US915.
	795
	796	if your region is not the US915, you have to configure the correct region for the miner.
	797
	798
	799	Access the hotspot CLI, and run these Linux commands
	800
	801
132.1	802	(% class="box infomessage" %)
	803	(((
131.1	804	~#~##update the software of dragino
	805
	806	apt update
	807
	808	apt install dragino*
132.1	809	)))
131.1	810
	811	[[image:image-20220609150452-2.png\|\|height="348" width="909"]]
	812
	813
	814
132.1	815	(% class="box infomessage" %)
	816	(((
131.1	817	~#~##configure the correct region for the miner and update it
	818
138.1	819	uci set miner.general.region=<Region; Such as AS923_1/AU915/US915/EU868/IN865>
131.1	820
	821	uci commit miner
	822
	823	minerup update
132.1	824	)))
131.1	825
137.1	826	[[image:image-20220609151513-5.png]]
131.1	827
	828
174.6	829
132.1	830	(% class="box infomessage" %)
	831	(((
131.1	832	~#~##check the miner version
	833
	834	draginoups
132.1	835	)))
131.1	836
135.1	837	[[image:image-20220609151419-3.png]]
131.1	838
143.1	839
174.6	840
143.1	841	(% class="box infomessage" %)
	842	(((
	843	~#~##unblock the function of wireless
	844	rfkill unblock wlan
	845	uci set wireless.general.mode=ap
	846	uci commit wireless
	847	)))
	848
	849	[[image:image-20220609161204-1.png]]
	850
131.1	851
160.1	852
174.1	853	= 9. How does the HP0D access to the network via a USB 4G Dongle =
160.1	854
174.6	855
172.1	856	We have reserved enough space inside the HP0D to use a USB 4G Dongle,
	857
	858	so you can install a USB 4G Dongle in order for the hotspot to access the network via 4G.
	859
	860
174.6	861	(% style="color:green" %)//Preparations://
172.1	862
	863	//1). A USB 4G Dongle, Such as HUAWEI E3327,ZTE...//
	864
	865	//2). A Sim card that can access the 4g network.//
	866
	867	//3). open the hotspot's shell.//
	868
	869
174.6	870
172.1	871	== 9.1. Open the HP0D shell and access the USB 4G Dongle into the Rpi. ==
	872
174.6	873
172.1	874	[[image:image-20220627153334-2.png]]
	875
	876
174.6	877
172.1	878	== 9.2. Checking the USB 4G Dongle network ==
	879
174.6	880
172.1	881	We have installed drivers for common USB 4G Dongle,
	882
	883	and managed by NetworkManager, once hp0d detects an available USB 4G Dongle it will try to dial up the range network
	884
	885
174.6	886	//HUAWEI-E3327//
172.1	887
	888	[[image:image-20220627154526-9.png\|\|height="762" width="725"]]
	889
	890
	891
174.6	892	//ZTE//
	893
172.1	894	[[image:image-20220627154201-5.png]]
	895
	896
	897
	898	= 10. PoE introduction =
	899
	900
174.6	901	//The HP0D is use the (% style="color:blue" %)IEEE 802.3 af compliant PoE port(%%) (input 44 ~~ 57 v, output 12V)//
160.1	902
161.1	903	//So you can use the PoE //switches// or PoE injector to power the device.//
160.1	904
	905
174.6	906	(((
	907	(% style="color:red" %)Note: The RJ45 Indicator light only represents the PoE power supply, so when you use DC to power the hotspot and the RJ45 indicator light is off ~-~--> this is normal
	908	)))
160.1	909
	910
174.6	911	(% style="background-color:yellow" %)Wiring schematic:
160.1	912
	913	[[image:image-20220616143347-1.png]]
	914
	915
	916
	917
173.1	918	= 11. OTA Version Info =
160.1	919
174.6	920
131.1	921	== When does the OTA update happen? ==
	922
	923
	924	//HP0D will check OTA update on a) Every Booting. b) Every Night. Below is the OTA update version info//
	925
174.6	926
	927
131.1	928	== # 2022/05/14 ==
	929
	930
	931	1. //Update to the latest miner version: miner-arm64_2022.05.13.0_GA//
	932	1. //Add postinst after auto-update//
	933	1. //Add Miner version mark.//
	934	1. //Add fast sync if miner GAP is large//
	935
152.1	936	== # 2022/05/18 ==
	937
	938
	939	1. //Update minerup to speed up synchronized blocks//
	940
131.1	941	== # 2022/05/24 ==
	942
151.1	943
152.1	944	1. //Update to the latest miner version: miner-arm64_2022.05.24.0_GA//
131.1	945
151.1	946	== # 2022/05/31 ==
131.1	947
174.6	948
152.1	949	1. //Add WiFi STA icon display//
	950	1. //Optimize AP icon display//
	951	1. //Optimize home icon display//
	952	1. //Fix for Miner icon URL bug//
	953	1. //Add the secondary server configuration//
151.1	954
173.1	955	= 12. Supports =
131.1	956
174.6	957
131.1	958	(((
	959	//If you are experiencing issues and can’t solve them, you can send mail to [[support@dragino.com>>mailto:support@dragino.com]].//
	960	)))
	961
	962	(((
	963	//With your question as detailed as possible. We will reply and help you in the shortest.//
	964
174.6	965
131.1	966
	967	)))
	968
173.1	969	= 13. Order Info =
131.1	970
	971
174.6	972	(% style="color:blue" %)HP0D-XXX
131.1	973
174.6	974	(% style="color:blue" %)XXX(%%): Frequency Band
131.1	975
174.6	976	* (% style="color:red" %)AS923(%%): LoRaWAN AS923 band
	977	* (% style="color:red" %)AU915(%%): LoRaWAN AU915 band
	978	* (% style="color:red" %)EU868(%%): LoRaWAN EU868 band
	979	* (% style="color:red" %)KR920(%%): LoRaWAN KR920 band
	980	* (% style="color:red" %)US915(%%): LoRaWAN US915 band
	981	* (% style="color:red" %)IN865(%%): LoRaWAN IN865 band
	982
173.1	983	= 14. Manufacturer Info =
131.1	984
174.6	985
131.1	986	(((
	987	Shenzhen Dragino Technology Development co. LTD
	988	)))
	989
	990	(((
	991	Room 202, Block B, BCT Incubation Bases (BaoChengTai), No.8 CaiYunRoad
	992	)))
	993
	994	(((
	995	Longcheng Street, LongGang District; Shenzhen 518116, China
	996
	997
	998
	999	)))
	1000
173.1	1001	= 15. FCC Warning =
131.1	1002
174.6	1003
131.1	1004	(((
	1005	This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
	1006	)))
	1007
	1008	(((
	1009	~-~- Reorient or relocate the receiving antenna.
	1010	)))
	1011
	1012	(((
	1013	~-~- Increase the separation between the equipment and receiver.
	1014	)))
	1015
	1016	(((
	1017	~-~- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
	1018	)))
	1019
	1020	(((
	1021	~-~- Consult the dealer or an experienced radio/TV technician for help.
	1022	)))
	1023
	1024	(((
	1025	Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
	1026	)))
	1027
	1028	(((
	1029	The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
	1030	)))

Wiki source code of HP0D Full Hotspot for Helium User Manual

Applications

Navigation