Last modified by Kilight Cao on 2024/12/31 16:31
<
From version < 342.1 >
edited by Kilight Cao
on 2024/12/31 15:35
To version < 234.1 >
edited by Xiaoye
on 2023/07/19 10:04
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -LPS8v2 -- LoRaWAN Indoor Gateway User Manual
1 +LPS8v2 LoRaWAN Indoor Gateway User Manual
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Kilight
1 +XWiki.Xiaoye
Content
... ... @@ -8,7 +8,7 @@
8 8  
9 9  )))
10 10  
11 -**Table of Contents:**
11 +**Table of Contents：**
12 12  
13 13  {{toc/}}
14 14  
... ... @@ -18,7 +18,7 @@
18 18  
19 19  = 1. Introduction =
20 20  
21 -== (% data-sider-select-id="66d5195f-ab1f-47c7-83cb-b027d0903e53" %)1.1 What is LPS8v2(%%) ==
21 +== 1.1 What is LPS8v2 ==
22 22  
23 23  
24 24  (((
... ... @@ -81,7 +81,7 @@
81 81  ** Semtech UDP Packet Forwarder
82 82  ** LoRaWAN Basic Station
83 83  ** ChirpStack-Gateway-Bridge (MQTT)
84 -* Built-in (% style="color:#037691" %)**ChirpStack**(%%) local LoRaWAN server
84 +* Built-in (% style="color:#037691" %)**The Things Network**(%%) local LoRaWAN server
85 85  * Built-in  (% style="color:#037691" %)**Node-Red** (%%)local Application server
86 86  
87 87  == 1.4 LED Indicators ==
... ... @@ -96,16 +96,16 @@
96 96  
97 97  (% style="color:blue" %)**➢ SYS LED**(%%):  This RGB LED will show different colors in different states:
98 98  
99 - ✓  **SOLID GREEN:** The device is alive with a LoRaWAN server connection.
99 + ✓ **SOLID GREEN:** The device is alive with a LoRaWAN server connection.
100 100  
101 - ✓  **BLINKING GREEN:** a) Device has internet connection but no LoRaWAN Connection. or b) Device is in booting stage, in this stage, it will BLINKING GREEN for several seconds and then with BLINKING GREEN together
101 + ✓ **BLINKING GREEN:** a) Device has internet connection but no LoRaWAN Connection. or b) Device is in booting stage, in this stage, it will BLINKING GREEN for several seconds and then with BLINKING GREEN together
102 102  
103 - ✓**  SOLID RED:** Device doesn't have an Internet connection.
103 + ✓** SOLID RED:** Device doesn't have an Internet connection.
104 104  
105 105  (% style="color:blue" %)**➢ WIFI LED**(%%): This LED shows the WIFI interface connection status.
106 106  
107 107  
108 -== 1.5 Button Instruction ==
108 +== 1.5 Button Intruction ==
109 109  
110 110  
111 111  LPS8-V2 has a black toggle button, which is:
... ... @@ -121,18 +121,6 @@
121 121   **LED status: ** ETH LED will SOLID BULE Until the restore is finished.
122 122  
123 123  
124 -(% style="color:red" %)**Note: Restoring factory Settings does not erase data from the LPS8-V2 built-in server**
125 -
126 -See this link for steps on how to clear data from the built-in server: **[[How to reset the built-in server>>http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/#H9.6A0Howtoresetthebuilt-inserver]]**
127 -
128 -
129 -When the gateway restores the factory settings is complete,
130 -
131 -The WiFi configuration will enable WiFi Access Point by default.
132 -
133 -The other configuration will be restored to the default configuration.
134 -
135 -
136 136  = 2. Quick Start =
137 137  
138 138  
... ... @@ -160,6 +160,7 @@
160 160  [[image:image-20230527085250-2.png||height="495" width="284"]]
161 161  
162 162  
151 +
163 163  ==== (% style="color:blue" %)**Method 2**(%%):  Connect via Ethernet with DHCP IP from the router ====
164 164  
165 165  
... ... @@ -174,6 +174,7 @@
174 174  [[image:image-20220622100129-1.png||height="332" width="1263"]]
175 175  
176 176  
166 +
177 177  ==== (% style="color:blue" %)**Method 3**(%%):  Connect via LPS8-V2 Fallback IP ====
178 178  
179 179  
... ... @@ -197,7 +197,7 @@
197 197  
198 198  Configure computer Ethernet port steps video: **[[attach:fallback ip.mp4||target="_blank"]]**
199 199  
200 -If you still can't access the LPS8-V2 fallback ip, follow this connection to debug : **[[Trouble Shooting>>http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/#H9.3A0FallbackIPdoesnotwork2Chowcanuserscheck]]**
190 +If you still can't access the LPS8-V2 fallback ip, follow this connection to debug : **[[Trouble Shooting>>http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/#H9.2A0FallbackIPdoesnotwork2Chowcanuserscheck]]**
201 201  
202 202  
203 203  3. In the PC, use IP address 172.31.255.254 to access the LPS8-V2 via Web or Console.
... ... @@ -205,6 +205,7 @@
205 205  [[image:image-20230111094247-2.png||height="619" width="1250"]]
206 206  
207 207  
198 +
208 208  ==== (% style="color:blue" %)**Method 4**(%%):  Connect via WiFi with DHCP IP from the router ====
209 209  
210 210  [[image:image-20220622100542-2.png||height="369" width="1256"]]
... ... @@ -213,18 +213,19 @@
213 213  Fill in the WiFi information by checking the box and clicking (% style="color:red" %)**Save&Apply**
214 214  
215 215  
216 -[[image:image-20241231151635-3.png||height="481" width="944"]]
207 +[[image:image-20220622102702-6.png]]
217 217  
218 218  
219 219  
220 220  **Wi-Fi configuration successful**
221 221  
222 -[[image:image-20241231151810-4.png||height="487" width="947"]]
223 223  
214 +[[image:image-20220622102847-7.png]]
224 224  
225 -[[image:image-20241231152015-6.png||height="506" width="1001"]]
226 226  
217 +[[image:image-20220622102901-8.png||height="476" width="938"]]
227 227  
219 +
228 228  === 2.1.2 Access Configure Web UI ===
229 229  
230 230  
... ... @@ -243,7 +243,7 @@
243 243  
244 244  (% style="color:blue" %)**Password:   dragino**
245 245  
246 -[[image:image-20240318160845-1.png]]
238 +[[image:image-20230106153501-1.png||height="367" width="894"]]
247 247  
248 248  
249 249  == 2.2  Typical Network Setup ==
... ... @@ -275,7 +275,7 @@
275 275  
276 276  The settings for WiFi Client is under page (% style="color:blue" %)**Network ~-~-> Wi-Fi**
277 277  
278 -[[image:image-20241231151512-2.png]]
270 +[[image:image-20230411095739-1.png||height="264" width="691"]]
279 279  
280 280  In the WiFi Survey Choose the WiFi AP, and input the Passphrase then click(% style="color:blue" %)** Save & Apply**(%%) to connect.
281 281  
... ... @@ -295,7 +295,7 @@
295 295  Second, Power off/ ON LPS8-V2 to let it detect the SIM card.
296 296  
297 297  
298 -[[image:image-20241231153425-1.jpeg||height="262" width="884"]]
290 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/LPS8N%20-%20LoRaWAN%20Gateway%20User%20Manual/WebHome/1657090855037-497.png?rev=1.1||alt="1657090855037-497.png"]]
299 299  
300 300  
301 301  The set up page is (% style="color:blue" %)**Network ~-~-> Cellular**
... ... @@ -306,9 +306,6 @@
306 306  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/LPS8N%20-%20LoRaWAN%20Gateway%20User%20Manual/WebHome/1657090932270-444.png?rev=1.1||alt="1657090932270-444.png"]]
307 307  
308 308  
309 -**Note: In most cases, the user simply types in the APN and checks the enable checkbox, without typing Pincode, Username, or Password settings.**
310 -
311 -
312 312  === 2.2.5  Check Internet connection ===
313 313  
314 314  
... ... @@ -402,7 +402,7 @@
402 402  
403 403  
404 404  (% class="wikigeneratedid" %)
405 -[[image:image-20220616110739-1.png||height="457" width="836"]]
394 +[[image:image-20220616110739-1.png||height="372" width="682"]]
406 406  
407 407  
408 408  (((
... ... @@ -432,40 +432,25 @@
432 432  
433 433  (((
434 434  Please see this instruction to know more detail and a demo for how to use of LoRaWAN Basic Station: __[[Use of LoRaWAN Basic Station - DRAGINO>>doc:Main.Use of LoRaWAN Basic Station.WebHome]]__
435 -
436 -
437 -== (% style="color:inherit; font-family:inherit; font-size:26px" %)3.4  Forwarder(%%) ==
438 438  )))
439 439  
440 -=== 3.4.1 Forwarder ~-~-> MQTT Forwarder ===
441 441  
427 +== 3.4 Network Settings ==
442 442  
443 -In the latest version, MQTT Forwarder functionality has been added to the LPS8V2 gateway by default
429 +=== 3.4.1 Network ~-~-> WiFi ===
444 444  
445 -Users can configure the MQTT Forwarder on the **Forwarder~-~->MQTT** interface, and when the configuration is successful, it will forward the sensor data of the lorawan server chirpstack built in LPS8v2
446 -
447 -For a detailed example of this feature, see this link:**[[MQTT Forward Instruction - DRAGINO>>http://wiki.dragino.com/xwiki/bin/view/Main/MQTT%20Forward%20Instruction/#H3.3A0UseLoRaWANProtocolforcommunication--ForLPS8V2]]**
448 -
449 -(% class="wikigeneratedid" %)
450 -[[image:image-20240902092034-1.png]]
451 -
452 -
453 -== 3.5 Network Settings ==
454 -
455 -=== 3.5.1 Network ~-~-> WiFi ===
456 -
457 457  Users can configure the wifi WAN and enable Wifi Access Point on this interface
458 458  
459 -[[image:image-20241231151434-1.png||height="608" width="1195"]]
433 +[[image:image-20230619095946-1.png||height="332" width="827"]]
460 460  
461 461  
462 -=== 3.5.2 Network ~-~-> System Status ===
436 +=== 3.4.2 Network ~-~-> System Status ===
463 463  
464 464  
465 465  [[image:image-20220820134112-2.png||height="539" width="668"]]
466 466  
467 467  
468 -=== 3.5.3 Network ~-~-> Network ===
442 +=== 3.4.3 Network ~-~-> Network ===
469 469  
470 470  
471 471  In the **Network ~-~-> Network** interface, Users can set the Ethernet WAN static ip address.
... ... @@ -473,7 +473,7 @@
473 473  [[image:image-20230214093657-2.png||height="333" width="858"]]
474 474  
475 475  
476 -=== 3.5.4 Network ~-~-> Cellular ===
450 +=== 3.4.4 Network ~-~-> Cellular ===
477 477  
478 478  
479 479  In the **Network ~-~-> Cellular** interface, Users can Enable Cellular WAN and configure Celluar.
... ... @@ -490,23 +490,20 @@
490 490  
491 491  Note: Known bugs: 4g consumes a lot of data which has been fixed by the package: dragino-ui-230716
492 492  
493 -[[Reduce data method>>http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/#H8.3Howtoreducethe4gdataconsumed]]
467 +Reduce data method
494 494  
495 -(% class="wikigeneratedid" id="H5.MQTTForwarder" %)
496 -(% id="cke_bm_4823S" style="display:none" %)
497 497  
470 +== 3.5 System ==
498 498  
499 -== 3.6 System ==
472 +=== 3.5.1 System ~-~-> System Overview ===
500 500  
501 -=== 3.6.1 System ~-~-> System Overview ===
502 502  
503 -
504 504  Shows the system info:
505 505  
506 -[[image:image-20231031162854-1.png]]
477 +[[image:image-20220917144512-5.png||height="618" width="853"]]
507 507  
508 508  
509 -=== 3.6.2 System ~-~-> System General ===
480 +=== 3.5.2 System ~-~-> System General ===
510 510  
511 511  
512 512  In the **System-> System General** interface, Users can customize the configuration System Password and set Timezone.
... ... @@ -516,29 +516,15 @@
516 516  [[image:image-20230214094058-3.png]]
517 517  
518 518  
519 -=== 3.6.3 System ~-~-> Backup/Restore ===
490 +=== 3.5.3 System ~-~-> Backup/Restore ===
520 520  
521 521  
522 -[[image:image-20231031162927-2.png]]
493 +[[image:image-20220917144725-6.png||height="208" width="869"]]
523 523  
524 -=== 3.6.4 System ~-~-> Reboot / Reset ===
525 525  
526 -In the **System-> Reboot / Reset** interface, users can can restart or reset the gateway.
496 +=== 3.5.4 System ~-~-> Remoteit ===
527 527  
528 -ETH LED will SOLID BULE Until the restore is finished.
529 529  
530 -When the gateway restores the factory settings is complete,
531 -
532 -The WiFi configuration will enable WiFi Access Point by default.
533 -
534 -The other configuration will be restored to the default configuration.
535 -
536 -[[image:image-20240203172853-1.png||height="365" width="901"]]
537 -
538 -
539 -=== 3.6.5 System ~-~-> Remoteit ===
540 -
541 -
542 542  In the **System-> Remoteit** interface, users can configure the gateway to be accessed remotely via Remote.it.
543 543  
544 544  
... ... @@ -547,7 +547,7 @@
547 547  [[image:image-20221230092303-2.png]]
548 548  
549 549  
550 -=== 3.6.6 System ~-~-> Package Management ===
507 +=== 3.5.5 System ~-~-> Package Management ===
551 551  
552 552  
553 553  In the **System ~-~-> Package Management** interface, Users can check the current version of Core Packages.
... ... @@ -555,114 +555,103 @@
555 555  [[image:image-20230214094316-4.png]]
556 556  
557 557  
558 -== 3.7 Logread ==
515 += 4. Build-in Server =
559 559  
560 -=== 3.7.1 LoRa Log ===
561 561  
518 +Since software version 0606,the default factory version of LPS8-V2 is installed with the built-in Applicant server: (% style="color:blue" %)**Node-Red**(%%), LoRaWAN Server: (% style="color:blue" %)**ChirpStack**(%%).
562 562  
563 -In the **Lograde ~-~-> LoRa Log page**, The users can view information about the gateway lora channel and the status of the IoT connection
520 +[[image:image-20230616175617-8.png||height="390" width="894"]]
564 564  
565 -[[image:image-20240416112509-1.png]]
522 +[[image:image-20230616175558-7.png||height="362" width="894"]]
566 566  
567 567  
568 -=== 3.7.2 Gateway Traffic ===
569 569  
570 -In the **Lograde ~-~-> Gateway Traffic page**, The users can view sensor packages about Recent LoRa uplink/downlink/Join requests
526 +(% style="color:red" %)**Note:**
571 571  
572 -[[image:image-20240416112618-2.png||height="705" width="1122"]]
528 + **Path**: Server ~-~-> Network Server
573 573  
530 + Server ~-~-> Application Server
574 574  
575 -=== 3.7.3 System Log ===
576 576  
577 -In the **Lograde ~-~-> System Log page**, The users can view information about the gateway system
533 +**Troubleshooting:**
578 578  
579 -[[image:image-20240416112649-3.png||height="820" width="1122"]]
580 580  
536 +**~ 1. URL does not jump properly**
581 581  
582 -=== 3.7.4 Record Log ===
538 + For the ChirpStack, you can use the local IP address and the port is **8080** to access it.
583 583  
584 -In the **Lograde ~-~-> Recod Log page**, The users can record the gateway curren running log.
540 + For the Node-Red, you can use the local IP address and the port is **1880** to access it.
585 585  
586 -[[image:image-20240416112712-4.png||height="319" width="1128"]]
587 587  
543 +== 4.1 LoRaWAN Network  Server ~-~- ChirpStack ==
588 588  
589 589  
590 -= 4. Build-in Server =
546 +You can access the gateway's built-in LNS server of (% style="color:blue" %)**ChirpStack **(%%)via the URL( (% style="background-color:yellow" %)__**//http:~/~/<hostname>:8080 or http:~/~/<local-IPV4-address> //**__(%%)) in your browser.
591 591  
592 -After the v1.7-230606 version, the LPS8-V2 default factory pre-installed the LoRaWAN Server: (% style="color:blue" %)**ChirpStack-V4**(%%), Application Server: (% style="color:blue" %)**Node-Red**(%%).
548 +Such as  (% style="background-color:yellow" %)__**//http:~/~/dragino-54ff12:8080  or http:~/~/<Local-IPV4-Address>//**__
593 593  
594 594  
595 -== 1). LoRaWAN Network Server: (% style="color:blue" %)**ChirpStack-V4**(%%) ==
551 +Login account:
596 596  
597 -[[image:image-20231106180816-4.png||height="416" width="896"]]
553 +**Username : ** (% style="background-color:yellow" %)**admin**
598 598  
599 -[[image:image-20231201165904-1.png||height="466" width="899"]]
555 +**Password: ** ** (% style="background-color:#ffff00" %)admin(%%)**
600 600  
601 -(% style="color:red" %)**Note:  The user can access the**(%%)** (% style="color:blue" %)ChirpStack-V4 (% style="color:red" %)via click the 'Launch' button, and the login account: admin/admin(%%)**
557 +[[image:image-20230616175332-6.png||height="519" width="1029"]]
602 602  
603 -For more information on server operations see [[Register LPSV2 to the built-in Chirpstack>>||anchor="H2.3TheLPS8-V2isregisteredandconnectedtoTheThingsNetwork"]]
604 604  
605 605  
561 +=== 4.1.1 The LPS8-V2 is registered and connected to Built-in ChirpStack ===
606 606  
607 -== 2). Application Network Server: (% style="color:blue" %)**Node-Red**(%%) ==
608 608  
564 +Users need to set the Service Provider to (% style="color:blue" %)**Local Host/Build-in Server **(%%) and click "Save&Apply"
609 609  
610 -[[image:image-20230616175558-7.png||height="362" width="894"]]
566 +The registration steps are basically similar to [[LPS8-V2 is registered and connected to The Things Network>>||anchor="H2.3TheLPS8-V2isregisteredandconnectedtoTheThingsNetwork"]]
611 611  
612 -[[image:image-20231201170355-2.png||height="536" width="899"]]
568 +[[image:image-20230321092456-1.png]]
613 613  
614 -(% style="color:red" %)**Note:  The user can access the**(%%)** (% style="color:blue" %)Node-RED (% style="color:red" %)via click the 'Launch' button(%%)**
615 615  
616 616  
572 +== 4.2 Application Server ~-~- Node-Red ==
617 617  
618 -== **3). Troubleshooting:** ==
619 619  
575 +You can access the gateway's built-in AS server of (% style="color:blue" %)**Node-Red **(%%)via the URL((% style="background-color:yellow" %)__**//http:~/~/<hostname>:1880 or http:~/~/<local-IPV4-address>//**__(%%)) in your browser.
620 620  
621 -* (((
622 -=== ** If the URL does not jump properly.** ===
623 -)))
624 624  
625 - For the ChirpStack, you can use the local IP address and the port is **8080** to access it.
578 +Such as (% style="background-color:yellow" %)__**//http:~/~/dragino-54ff12:1880  or http:~/~/<Local-IPV4-Address>//**__
626 626  
627 - For the Node-Red, you can use the local IP address and the port is **1880** to access it.
628 628  
581 +[[image:image-20220725172124-3.png||height="610" width="843"]]
629 629  
630 -* (((
631 -=== ** How to install InfluxDB, Garfana.** ===
632 -)))
633 633  
634 - The LPS8V2 is not pre-installed with InfluxDB and Garfana, the users can install them, see [[InfluxDB>>http://wiki.dragino.com/xwiki/bin/view/Main/Armbian%20OS%20instruction/#H2.6HowtoinstallGrafanaandinfluxdb]]
635 635  
585 +=== **Using Node-Red, InfluxDB and Grafana** ===
636 636  
637 -* (((
638 -=== ** How to upgrade the gateway node.js to the latest version.** ===
639 -)))
587 +The LPS8-V2 supports this combination, the default, Node-red is pre-installed but the InfluxDB and Grafana is not pre-installed.
640 640  
641 - The user can upgrade nodejs, see [[Upgrade Nodejs>>http://wiki.dragino.com/xwiki/bin/view/Main/Armbian%20OS%20instruction/#H2.5Howtoupgradethenodejsversiontothelatest.]]
642 642  
590 +the users can refer to this link to install them.
643 643  
644 -* (((
645 -=== ** How to batch register device on the built-in Chirpstack network server** ===
646 -)))
592 +[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Armbian%20OS%20instruction/#H2.6HowtoinstallGrafanaandinfluxdb>>http://wiki.dragino.com/xwiki/bin/view/Main/Armbian%20OS%20instruction/#H2.6HowtoinstallGrafanaandinfluxdb]]
647 647  
648 - The user can register devices in batch on the gateway Web UI, see [[Batch Register>>http://wiki.dragino.com/xwiki/bin/view/Main/Notes%20for%20ChirpStack/#H11.A0HowtouseChirpstackAPItobatchregisterSensorNode2FGatewayinChistapstackServer]]
649 649  
595 +=== **Upgrade the node.js** ===
650 650  
651 -* (((
652 -=== ** Why my gateway is not Chirpstack?** ===
653 -)))
597 +By default, the LPS8-V2 node.js uses the pre-install version v12 which is due to Debian the ultra-stable via ultra-old.
654 654  
655 - After June '23, the default factory LPS8V2 pre-installed Chirpstack-V4 instead of The Things Stack, the users can migrate to Chistack-V4, see **[[Change TTN Stack v3 to ChirpStack>>http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/#H9.2Build-inTheThingsNetworkmigratetoChirpStack]]**
656 656  
600 +the users can refer to this link to upgrade them.
657 657  
658 -* (((
659 -=== ** How to disable the built-in server** ===
660 -)))
602 +[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Armbian%20OS%20instruction/#H2.5Howtoupgradethenodejsversiontothelatest.>>http://wiki.dragino.com/xwiki/bin/view/Main/Armbian%20OS%20instruction/#H2.5Howtoupgradethenodejsversiontothelatest.]]
661 661  
604 +
605 +== 4.3 How to disable the built-in server ==
606 +
607 +
608 +Use the following commands to start and stop the TTNv3 service:
609 +
662 662  (% class="box infomessage" %)
663 663  (((
664 -Use the following commands to start and stop the TTNv3 service:**     **
665 -
666 666  **# start**
667 667  systemctl start ttnstack
668 668  
... ... @@ -676,10 +676,10 @@
676 676  systemctl disable ttnstack
677 677  )))
678 678  
679 -(% class="box infomessage" %)
680 -(((
681 681  Use the following commands to start and stop the Node-Red service:
682 682  
627 +(% class="box infomessage" %)
628 +(((
683 683  **# start**
684 684  systemctl start nodered
685 685  
... ... @@ -694,44 +694,36 @@
694 694  )))
695 695  
696 696  
697 -* (((
698 -=== ** How to choose the Chirpstack server frequency SubBand** ===
699 -)))
643 +== 4.4 How to use ChirpStack on LPS8-V2 ==
700 700  
701 -**~ ** The user has to choose a SubBand if using CN470, US915, AU915, or AS923.
702 702  
703 - Note: Since the subbands of the Chirpstack are counted from 0, us915_1 of the Chirpstack is equal to US915 FSB2, so if your LoRa Rdio is using the US915 FSB2 you have to choose the us915_1 as the Chirpstack FSB.
646 +By default, the built-in LoRaWAN network server used on LPS8v2 is TTNv3, so users need follow this link to install chirpstack:
704 704  
705 -[[image:image-20230602140406-3.png||height="480" width="918"]]
648 +**[[Build-in The Things Network migrate to ChirpStack>>http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/#H9.2Build-inTheThingsNetworkmigratetoChirpStack]]**
706 706  
707 707  
708 -When the configuration is complete, click** "Save&Apply"**.
651 +=== 4.4.1 How do users choose the chirpstack server frequency SubBand ===
709 709  
710 710  
711 -(% style="color:red" %)**Note:**(%%) When adding the device profile, the selected Region configuration is also calculated from 0, so setting it to us915_1 corresponds to US915 Sub Band 2.
654 +On the **Server ~-~-> Network Server** interface, choose the frequency Plan first.
712 712  
713 -[[image:image-20230602143122-4.png||height="511" width="983"]]
656 +If the frequency Plan used is CN470, US915, AU915, or AS923, the user needs to choose a frequency sub-band, because the frequency Sub Band of ChirpStack starts from 0, so for example, us915_1 corresponds to the actual frequency US915_2.
714 714  
658 +[[image:image-20230602140406-3.png||height="480" width="918"]]
715 715  
716 716  
717 -= 5. Watch Dog =
661 +When the configuration is complete, click** "Save&Apply"**.
718 718  
719 719  
720 -The watchdog will guard the LPS8V2 to avoid the need to perform a reboot manually after down occurs
664 +(% style="color:red" %)**Note:**(%%) When adding device profile, the selected Region configuration is also calculated from 0, so setting it to us915_1 corresponds to US915 Sub Band 2.
721 721  
666 +[[image:image-20230602143122-4.png||height="511" width="983"]]
722 722  
723 -LPS8-V2 supports the Watch Dog but is not enabled by the previous releases(2023-11-24 )
724 724  
725 -The uses can be via the below method to enable Watch Dog:
669 += 5. How the LPS8-V2 connects to Chirpstack via gateway-bridge =
726 726  
727 -(% class="box infomessage" %)
728 -(((
729 -wget -P /tmp/ http:~/~/repo.dragino.com/release/tool/watchdog/enable_watchdog.sh && chmod +x /tmp/enable_watchdog.sh && /tmp/enable_watchdog.sh
730 -)))
731 731  
732 -[[image:image-20231124113209-1.png||height="470" width="1157"]]
733 733  
734 -
735 735  = 6. How users can access LPS8-V2 using serial USB =
736 736  
737 737  
... ... @@ -785,6 +785,7 @@
785 785  
786 786  1). Using the Linux command to upgrade the system
787 787  
726 +
788 788  (% class="box infomessage" %)
789 789  (((
790 790  **apt update && apt install *dragino***
... ... @@ -793,346 +793,68 @@
793 793  
794 794  2). Upgrade the system via the Web page button of "Manual Update"
795 795  
796 -(% style="color:red" %)**Note: this method needs about 10 mins, so you will get the log after 10 mins.  **
797 797  
736 +**Note: this method needs about 10 mins, so you will get the log after 10 mins.  **
737 +
798 798  [[image:image-20230607093849-1.png]]
799 799  
800 800  
801 -= (% data-sider-select-id="f31494a0-5f58-4b5c-820e-9cb1be76d96f" %)8 How do I view gateway logs(%%) =
802 802  
803 -=== (% data-sider-select-id="2c782a3d-7138-45c4-bbdf-09c0e27ef896" %)8.1 LoRaWAN Log:(%%) ===
742 += 8. FAQ =
804 804  
744 +== 8.1 How to change Hostname ==
805 805  
806 -==== Semtech UDP Log : ====
807 807  
808 -When the gateway starts LoRaWAN Semtech UDP, users can check the logs of the Semtech UDP in the **LogRead ~-~-> System Log** interface
747 +By default, Hostname is dragino-xxxxxx,If the user needs to change the hostname, the user needs to access the linux console of LPS8v2 and enter the following command:
809 809  
810 -[[image:image-20231017112115-2.png||height="611" width="821"]]
811 -
812 -
813 -==== Station Log: ====
814 -
815 -When the gateway starts Basic Station, users can check the logs of the station in the **LogRead ~-~-> System Log** interface
816 -
817 -[[image:image-20231017111606-1.png||height="622" width="821"]]
818 -
819 -
820 -=== (% data-sider-select-id="de76f982-b2e5-4327-aab4-8890814f5f53" %)8.2  4G Log(%%) ===
821 -
822 -
823 -User needs to access the Linux console of the gateway and enter the following command:
824 -
825 825  (% class="box infomessage" %)
826 826  (((
827 -cat /var/log/qmilog.txt
751 +hostnamectl set-hostname dragino-123456
828 828  )))
829 829  
830 -[[image:image-20231017114417-3.png||height="543" width="679"]]
754 +[[image:image-20230517102429-1.png]]
831 831  
756 +After the configuration is complete, run "reboot" to restart the gateway.
832 832  
833 -LPS8v2 use **quectel-CM** linux drive for dial up. The manual of this driver can be found here: [[**quectel-CM driver user manual**>>https://www.dropbox.com/scl/fi/73n2jl2c5r8h4i187to4n/Quectel_WCDMA_LTE_Linux_USB_Driver_User_Guide_V1.9-20190212.pdf?rlkey=j8834bw38d4neieisg54zngu9&st=kjsd4zx4&dl=0]].
834 834  
835 -Below are some commands as reference:
759 +== 8.2 Build-in The Things Network migrate to ChirpStack ==
836 836  
837 ->Usage:  /usr/bin/quectel-CM [options]
838 -> -s [apn [user password auth]]  Set apn/user/password/auth get from your network provider. auth: 1~~pap, 2~~chap
839 -> -p pincode Verify sim card pin if sim card is locked
840 -> -p [quectel-][qmi|mbim]-proxy  Request to use proxy
841 -> -f logfilename Save log message of this program to file
842 -> -u usbmonlog filename  Save usbmon log to file
843 -> -i interface Specify which network interface to setup data call when multi-modems exits
844 -> -4 Setup IPv4 data call (default)
845 -> -6 Setup IPv6 data call
846 -> -k pdn Specify which pdn to hangup data call (by send SIGINT to 'quectel-CM -n pdn')
847 -> -m iface-idx Bind QMI data call to wwan0_<iface idx> when QMAP used. E.g '-n 7 -m 1' bind pdn-7 data call to wwan0_1
848 -> -b Enable network interface bridge function (default 0)
849 -> -v Verbose log mode, for debug purpose.[Examples]
850 ->Example 1: /usr/bin/quectel-CM
851 ->Example 2: /usr/bin/quectel-CM -s 3gnet
852 ->Example 3: /usr/bin/quectel-CM -s 3gnet -v
853 853  
762 +Migrate guide:
854 854  
764 +**1. Ensure that the gateway is in good network condition, Recommended use of ETH.**
855 855  
856 -=== (% data-sider-select-id="ec43d85c-19ec-48b0-a4fc-0ecd76f17fc4" %)8.3 Dmesg Log(%%) ===
766 +**2. On the Server ~-~-> Network Server interface, click "Management"**
857 857  
768 +[[image:image-20230616162454-1.png]]
858 858  
859 -Users can check the logs of the Dmesg in the **LogRead ~-~-> System Log** interface:
860 860  
861 -[[image:image-20231017115330-5.png||height="565" width="740"]]
771 +**3. Click "Migrate-Chirpstack"**
862 862  
773 +[[image:image-20230616162742-2.png]]
863 863  
864 -=== (% data-sider-select-id="3a977a3e-9417-40fa-bdfb-2544a88744a9" %)8.4 Record Log(%%) ===
865 865  
776 +**4. Strat Install **
866 866  
867 -Users can record DMESG logs and LoRaWAN logs on the **LogRead ~-~->Record Log** interface
868 868  
869 -[[image:image-20231017115124-4.png||height="215" width="880"]]
779 +Click start Install and wait until the migration succeeds
870 870  
781 +[[image:image-20230616162934-3.png]]
871 871  
872 -=== (% data-sider-select-id="b988f832-4b37-4a61-b951-ff2138ad9cba" %)8.5 View gateway logs via Linux Command(%%) ===
873 873  
784 +**5.Migration complete check result**
874 874  
875 -**Semtech UDP Log :**
786 +[[image:image-20230616174526-4.png||height="706" width="983"]]
876 876  
877 -(% class="box infomessage" %)
878 -(((
879 -**journalctl -u draginofwd -f**
880 -)))
881 881  
882 -[[image:image-20231207144627-1.png||height="371" width="1017"]]
789 +[[image:image-20230616180004-9.png]]
883 883  
884 884  
885 -**Station Log:**
792 +== 8.3 How to reduce the 4g data consumed ==
886 886  
887 -(% class="box infomessage" %)
888 -(((
889 -**tail -f /var/log/station.log **
890 -)))
891 -
892 -[[image:image-20231207144758-2.png||height="132" width="1022"]]
893 -
894 -
895 -**Dmesg Log:**
896 -
897 -(% class="box infomessage" %)
898 -(((
899 -**dmesg**
900 -)))
901 -
902 -[[image:image-20231207145210-3.png||height="310" width="1021"]]
903 -
904 -
905 -
906 -(% data-sider-select-id="65e92cfb-62df-4513-8469-b74edd72dea5" %)
907 -= (% data-sider-select-id="ce97a758-4348-4c0c-86eb-412b6b8d3996" %)9. More Services(%%) =
908 -
909 -== (% data-sider-select-id="6b164b64-51ae-4144-8ffd-5cd725b3bb5f" %)9.1 NTP Service/Time Synchronization(%%) ==
910 -
911 -The gateway time sync service is provided by chrony service
912 -
913 -
914 -=== 1). Modify the NTP server address: ===
915 -
916 -(% class="box infomessage" %)
917 -(((
918 -Configuration file path:  /etc/chrony/chrony.conf
919 -)))
920 -
921 -
922 -=== 2). Start/Stop/Enable/Disable NTP service: ===
923 -
924 -(% class="box infomessage" %)
925 -(((
926 -systemctl start chrony
927 -\\systemctl stop chrony
928 -\\systemctl disable chrony
929 -\\systemctl enable chrony
930 -)))
931 -
932 -
933 -(% data-sider-select-id="61881d06-3f91-437c-8b64-7032dea3c970" %)
934 -= (% data-sider-select-id="fb64fcfa-81b6-41b5-ae81-81d94960d7dd" %)10. More features(%%) =
935 -
936 -(% data-sider-select-id="692f00f1-a7cc-4954-ac62-0a5dddb0a0c6" %)
937 -== (% data-sider-select-id="ec6a5e23-ba91-46d9-8042-1e4c6a7b3b36" %)10.1 Chirpstack MQTT Forwarder(%%) ==
938 -
939 -
940 -ChirpStack MQTT Forwarder is a MQTT packet forwarder for LoRa gateways. By default it forwards packets in Protobuf binary format, optionally it can be configured to use JSON encoding for debugging. In contrast to the ChirpStack Gateway Bridge, this component must always be installed on the gateway.
941 -
942 -
943 -(% data-sider-select-id="d2b54844-aad8-4198-9f17-841cd68db9b3" %)
944 -=== (% data-sider-select-id="fb64fcfa-81b6-41b5-ae81-81d94960d7dd" %)10(% data-sider-select-id="0870eb11-ff25-47fc-9e3c-80a68bbf3933" %).1.1 Configure Packet Forwarder(%%) ===
945 -
946 -In the Dragino web-interface, you must configure the Packet Forwarder such that it forwards to localhost on port 1700.
947 -
948 -(% data-sider-select-id="48576a4e-42ef-4ac9-83b4-122fc10c6629" %)
949 -By default, the web-interface can be accessed by entering the following URL in your browser: (% data-sider-select-id="c2683c51-0bf8-4ac5-87be-c50edacc8f4b" %)**http:~/~/GATEWAY-IP-ADDRESS**(%%) (replace GATEWAY-IP-ADDRESS by the actual IP address of your gateway). The default credentials are root / dragino.
950 -
951 -* In the **LoRaWAN** menu, click **LoRaWAN ~-~- Semtech UDP**
952 -* Configure the following settings:
953 -** **Service Provider:** //Custom / Private LoRaWAN//
954 -** **Server Address:** localhost
955 -** **Uplink Port:** 1700
956 -** **Downlink Port:** 1700
957 -* Click **Save & Apply**
958 -
959 -[[image:image-20240518145929-2.png||height="652" width="727"]]
960 -
961 -
962 -(% data-sider-select-id="716df9b1-d844-4797-bce9-9b1adf49b072" %)
963 -=== (% data-sider-select-id="fb64fcfa-81b6-41b5-ae81-81d94960d7dd" %)10(% data-sider-select-id="ffba644f-a9d5-4e93-a9da-9f9e49d596d9" %).1.2 Install ChirpStack MQTT Forwarder(%%) ===
964 -
965 -
966 -(% data-sider-select-id="2a752131-c23e-4da4-b142-5880dd688c39" %)
967 -(% data-sider-select-id="833bbe42-c175-4e13-ab7a-c8abc30378d0" %)**SSH login**
968 -
969 -First you must login into the gateway using SSH:
970 -
971 -(% class="box infomessage" data-sider-select-id="608a94b0-8dee-453d-9433-5fe12c6559e5" %)
972 -(((
973 -ssh root@GATEWAY-IP-ADDRESS
974 -)))
975 -
976 -(% data-sider-select-id="63adc977-8227-4585-ab1d-eea44a01c34c" %)
977 -The default password is: (% data-sider-select-id="5fad2844-9bd3-49e2-979b-ffd184b923cf" %)**dragino**(%%).
978 -
979 -
980 -(% data-sider-select-id="216fb9b4-6cee-4cb6-8b71-0a9cda3bd96a" %)
981 -(% data-sider-select-id="914750d6-03c5-48fe-ad27-49e99d95d877" %)**Download **(% data-sider-select-id="94e274ee-d341-40dc-8ca8-dc3c3b4c4981" %)**package**
982 -
983 -(% data-sider-select-id="f95485e3-b535-4ea2-b0aa-0c46b5254782" %)
984 -Use the following commands to download the latest version of the ChirpStack MQTT Forwarder package:
985 -
986 -(% class="box infomessage" data-sider-select-id="ab1338ab-a215-4185-8552-1efd6e067858" %)
987 -(((
988 -cd /tmp
989 -wget https:~/~/artifacts.chirpstack.io/downloads/chirpstack-mqtt-forwarder/chirpstack-mqtt-forwarder_4.3.0_linux_armhf.deb
990 -)))
991 -
992 -
993 -(% data-sider-select-id="e59f1bad-427f-47b8-bc97-a818490576c4" %)
994 -(% data-sider-select-id="1b512eaf-c564-4835-afac-548b9a6a7045" %)**Install **
995 -
996 -Use the dpkg package-manager to install the downloaded package. Example:
997 -
998 -(% class="box infomessage" data-sider-select-id="7e7ff0cf-c367-4ff0-9387-f4eb82f3c89e" %)
999 -(((
1000 -dpkg -i chirpstack-mqtt-forwarder_4.3.0_linux_armhf.deb
1001 -)))
1002 -
1003 -[[image:image-20240518152148-4.png]]
1004 -
1005 -
1006 -(% data-sider-select-id="69e4a485-6ea8-46e7-97a3-8666bc9423a7" %)
1007 -**Configuration**
1008 -
1009 -To connect the ChirpStack MQTT Forwarder to your MQTT broker, you must update the ChirpStack MQTT Forwarder configuration file.
1010 -
1011 -(% data-sider-select-id="e98443ef-dcc1-4be1-ad3e-ec31b0a580b4" %)
1012 -This file is located at: (% data-sider-select-id="60301edc-5082-44e9-a91a-688327092116" %)**/etc/chirpstack-mqtt-forwarder/chirpstack-mqtt-forwarder.toml**
1013 -
1014 -
1015 -**ChirpStack MQTT Forwarder Setting:**
1016 -
1017 -(% class="box" data-sider-select-id="1d70062d-64ab-410b-bd8e-476c73d5dd70" %)
1018 -(((
1019 -topic_prefix  ~-~->  This corresponds to the frequency of the ChirpStack server
1020 -
1021 -server  ~-~->  Fill in the ChirpStack server address, Example: tcp:~/~/10.130.2.15:1883
1022 -)))
1023 -
1024 -username,password,ca_cert,tls_cert,tls_key parameters should be set as required.
1025 -
1026 -
1027 -Use commands to modify configuration files:
1028 -
1029 -(% class="box infomessage" data-sider-select-id="d552b27f-cfd2-4f5a-9b7f-b627f5dd3387" %)
1030 -(((
1031 -vim /etc/chirpstack-mqtt-forwarder/chirpstack-mqtt-forwarder.toml
1032 -)))
1033 -
1034 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/LPS8N%20-%20LoRaWAN%20Gateway%20User%20Manual/WebHome/image-20240518141059-6.png?rev=1.1||alt="image-20240518141059-6.png"]]
1035 -
1036 -
1037 -**(Re)start and stop commands**
1038 -
1039 -Use the following commands to (re)start and stop the ChirpStack MQTT Forwarder service:
1040 -
1041 -(% class="box infomessage" data-sider-select-id="61c3c343-2cb9-4b07-8741-5d5da2d88ec3" %)
1042 -(((
1043 -# start
1044 -
1045 -(% data-sider-select-id="5482a31e-3aa0-403c-aec5-117839958068" %)
1046 -systemctl start chirpstack-mqtt-forwarder
1047 -
1048 -# stop
1049 -
1050 -systemctl stop chirpstack-mqtt-forwarder
1051 -
1052 -# restart
1053 -
1054 -systemctl restart chirpstack-mqtt-forwarder
1055 -)))
1056 -
1057 -(% data-sider-select-id="1cea423f-9653-47e6-8022-aadcb684f191" %)
1058 -(% data-sider-select-id="f385e712-68bc-48fd-8b94-67a0c7e7cb70" %)**Note: If the LPS8v2 built-in server is running, it will cause a port conflict**
1059 -
1060 -
1061 -**Check result**
1062 -
1063 -(% data-sider-select-id="43d1d40a-2620-4547-b00d-f78dd5427215" %)
1064 -Use "** journalctl -u chirpstack-mqtt-forwarder -f(% data-sider-select-id="ab74df8a-b859-4afa-9c26-d0807e860e6c" %) (%%)**" to check the operation of ChirpStack MQTT Forwarder.
1065 -
1066 -[[image:image-20240518154223-5.png]]
1067 -
1068 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/LPS8N%20-%20LoRaWAN%20Gateway%20User%20Manual/WebHome/image-20240518143050-8.png?width=1170&height=702&rev=1.1||alt="image-20240518143050-8.png"]]
1069 -
1070 -
1071 -== (% data-sider-select-id="de90793f-d833-4885-8b59-d0880f7256e6" %)10.2 As a Data-only hotspot connect the helium blockchain(%%) ==
1072 -
1073 -
1074 -(% class="box infomessage" %)
1075 -(((
1076 -(% data-sider-select-id="3359233b-fcc9-4415-9bee-4151919fbb2e" %)
1077 -apt update && apt install helium-gateway
1078 -)))
1079 -
1080 -
1081 -== (% data-sider-select-id="de90793f-d833-4885-8b59-d0880f7256e6" %)10.3 (%%)How does LPS8v2 filter unwanted lorawan packets ==
1082 -
1083 -
1084 -This feature is to filter the unwanted LoRaWAN packets. Purpose is to save the upstream traffic especially for a 4G cellular connection.
1085 -
1086 -Please refer to the link below for specific usage：**[[Filter unwanted LoRaWAN packets>>https://wiki.dragino.com/xwiki/bin/view/Main/Filter%20unwanted%20LoRaWAN%20packets/]]**
1087 -
1088 -
1089 -= (% data-sider-select-id="20d4ea6b-7328-46c6-bc97-f0050cfe382e" %)11. FAQ(%%) =
1090 -
1091 -== (% data-sider-select-id="9fbcac50-3c87-43d9-8611-8d311fcb7820" %)11.1 How to change Hostname(%%) ==
1092 -
1093 -
1094 -By default, Hostname is dragino-xxxxxx,If the user needs to change the hostname, the user needs to access the linux console of LPS8v2 and enter the following command:
1095 -
1096 -(% class="box infomessage" %)
1097 -(((
1098 -hostnamectl set-hostname dragino-123456
1099 -)))
1100 -
1101 -[[image:image-20230517102429-1.png]]
1102 -
1103 -After the configuration is complete, run "reboot" to restart the gateway.
1104 -
1105 -
1106 -== (% data-sider-select-id="20d4ea6b-7328-46c6-bc97-f0050cfe382e" %)11(% data-sider-select-id="62cdc3f4-fb6f-4e4d-92a5-60449c8b462f" %).2 Build-in The Things Network migrate to ChirpStack(%%) ==
1107 -
1108 -
1109 -Migrate guide:
1110 -
1111 -To stabilize the completion of the migration, The users can migrate in one of the following ways
1112 -
1113 -**Method 1. Using the Linux shell, **
1114 -
1115 -**Method 2. Flash a new image with the Chirpstack**
1116 -
1117 -
1118 -=== Method 1: Using the Linux shell ===
1119 -
1120 -(% class="box infomessage" %)
1121 -(((
1122 -wget -P /tmp [[http:~~/~~/repo.dragino.com/release/tool/chirpstack/migrate_chirpstack>>http://repo.dragino.com/release/tool/chirpstack/migrate_chirpstack]] && chmod +x /tmp/migrate_chirpstack && /tmp/migrate_chirpstack
1123 -)))
1124 -
1125 -
1126 -=== Method 2: Flash a new image ===
1127 -
1128 -Image flash steps: [[How to flash a new image(OS) to the gateway(LPS8V2)>>http://wiki.dragino.com/xwiki/bin/view/Main/Armbian%20OS%20instruction/#H2.3A0Howtoflashanewimage28OS29tothegateway28LPS8V229]]
1129 -
1130 -
1131 -== (% data-sider-select-id="20d4ea6b-7328-46c6-bc97-f0050cfe382e" %)11(% data-sider-select-id="b2a44672-8abb-425d-a823-f2faa334cdb7" %).3 How to reduce the 4g data consumed(%%) ==
1132 -
1133 -
1134 1134  1). The gateway will check the network via ping 1.1.1.1/8.8.8.8 which will consume a lot of data, you can set the interval time to reduce data consume.
1135 1135  
796 +
1136 1136  [[image:image-20230719100239-1.png||height="724" width="994"]]
1137 1137  
1138 1138  
... ... @@ -1140,53 +1140,18 @@
1140 1140  
1141 1141  [[image:image-20230719100332-2.png]]
1142 1142  
1143 -
1144 1144  3. Disable the auto-update:
1145 1145  
1146 1146  [[image:image-20230719100419-3.png||height="458" width="995"]]
1147 1147  
1148 1148  
1149 -== (% data-sider-select-id="20d4ea6b-7328-46c6-bc97-f0050cfe382e" %)11(% data-sider-select-id="457c03ce-1aaa-44c6-bf8e-0298ca8045e4" %).4 How to change built-in LoRaWAN Server from ChirpStack v4 to TTN Stack v3.(%%) ==
1150 1150  
1151 1151  
1152 -By default, the LPS8v2's built-in server is ChirpStack v4,
811 += 9. Trouble Shooting =
1153 1153  
1154 -If the user needs to change the built-in server from ChirpStack v4 to TTN Stack v3, the User needs to download the image and flash it to the LPS8v2 gateway:
813 +== 9.1  I can't log in to the built-in Server TTN Stack which shows '**Login failed**'. ==
1155 1155  
1156 -[[https:~~/~~/www.dropbox.com/scl/fi/qwtaw4i4dqonzramr93e4/dragino-LPS8V2-TTN-231124.rar?rlkey=nrftlkd1h8en6j07vzbhpj9ui&dl=0>>https://www.dropbox.com/scl/fi/qwtaw4i4dqonzramr93e4/dragino-LPS8V2-TTN-231124.rar?rlkey=nrftlkd1h8en6j07vzbhpj9ui&dl=0]]
1157 1157  
1158 -
1159 -Image flash steps: [[How to flash a new image(OS) to the gateway(LPS8V2)>>http://wiki.dragino.com/xwiki/bin/view/Main/Armbian%20OS%20instruction/#H2.3A0Howtoflashanewimage28OS29tothegateway28LPS8V229]]
1160 -
1161 -
1162 -== (% data-sider-select-id="20d4ea6b-7328-46c6-bc97-f0050cfe382e" %)11(% data-sider-select-id="457c03ce-1aaa-44c6-bf8e-0298ca8045e4" %).5 (%%)How to check my USB port dev/tty after i plug in USB device. ==
1163 -
1164 -
1165 -When an external USB device is connected to LPS8v2, the user can access the Linux console of the LPS8v2 gateway and run the following command to check the USB port dev/tty:
1166 -
1167 -(% class="box infomessage" %)
1168 -(((
1169 -dmesg
1170 -)))
1171 -
1172 -[[image:image-20240803095144-1.png]]
1173 -
1174 -
1175 -
1176 -== (% data-sider-select-id="20d4ea6b-7328-46c6-bc97-f0050cfe382e" %)11(% data-sider-select-id="82550df9-987d-4f58-9877-86a0c5e621a4" %).6 DIN Mount Reference:(%%) ==
1177 -
1178 -
1179 -[[image:image-20240318095605-1.jpeg||height="472" width="472"]]
1180 -
1181 -[[image:image-20240318095617-2.png]]
1182 -
1183 -
1184 -
1185 -
1186 -= (% data-sider-select-id="9b024263-b754-45b6-ac15-22f86a4e1436" %)12. Trouble Shooting(%%) =
1187 -
1188 -== (% data-sider-select-id="cb7a0b2f-4144-4f58-86d0-64a15944840e" %)12.1  I can't log in to the built-in Server TTN Stack which shows '**Login failed**'.(%%) ==
1189 -
1190 1190  [[image:image-20220920135918-1.png]]
1191 1191  
1192 1192  
... ... @@ -1202,7 +1202,7 @@
1202 1202  [[image:image-20220920141936-2.png]]
1203 1203  
1204 1204  
1205 -== (% data-sider-select-id="9b024263-b754-45b6-ac15-22f86a4e1436" %)12(% data-sider-select-id="f34b4950-25aa-4a6d-a2b4-4af0ec0010a7" %).2  The built-in TTN status is "Not Running" and the URI is "dragino-123456". How users fix this problem(%%) ==
831 +== 9.2  The built-in TTN status is "Not Running" and the URI is "dragino-123456". How users fix this problem ==
1206 1206  
1207 1207  
1208 1208  When this problem occurs, click "**Update To DEFAULT**" ,this problem will be fixed.
... ... @@ -1210,13 +1210,13 @@
1210 1210  [[image:image-20230508171607-1.png]]
1211 1211  
1212 1212  
1213 -== (% data-sider-select-id="9b024263-b754-45b6-ac15-22f86a4e1436" %)12(% data-sider-select-id="a7b8cd40-2ec5-4b4b-8220-d32ce0a303a0" %).3  Fallback IP does not work, how can users check(%%) ==
839 +== 9.3  Fallback IP does not work, how can users check ==
1214 1214  
1215 1215  
1216 1216  When the computer has completed the above fallback IP configuration,the LPS8v2 Web UI is still not accessible via fallback IP.
1217 1217  
1218 1218  
1219 -**~1. Check whether the configuration is correct**
845 +**1.Check whether the configuration is correct**
1220 1220  
1221 1221  Run the CMD command to ipconfig and ping 172.31.255.254.
1222 1222  
... ... @@ -1232,7 +1232,7 @@
1232 1232  If the firewall is not down, this will affect access to the gateway.
1233 1233  
1234 1234  
1235 -== (% data-sider-select-id="9b024263-b754-45b6-ac15-22f86a4e1436" %)12(% data-sider-select-id="b7eec45b-ad8c-4621-a815-f457810d25f4" %).4  Click "Manual_Update", why there is no response?(%%) ==
861 +== 9.4  Click "Manual_Update", why there is no response? ==
1236 1236  
1237 1237  
1238 1238  When you click "Manual_Update", the gateway will finish updating within 10 minutes and display the update log.
... ... @@ -1241,40 +1241,10 @@
1241 1241  [[image:image-20230527090555-3.png||height="660" width="832"]]
1242 1242  
1243 1243  
1244 -== (% data-sider-select-id="9b024263-b754-45b6-ac15-22f86a4e1436" %)12(% data-sider-select-id="ac1f33b3-1f28-477d-880c-534ac36adcbe" %).5  Why the LPS8V2's Access Point does not do not appear & Fallback IP unable to access(%%) ==
870 += (% style="color:inherit; font-family:inherit; font-size:29px" %)10. Supports(%%) =
1245 1245  
1246 1246  
1247 -Earlier versions of the LPS8V2 which missing the AP driver and not installed the fallback package, so the users have to do an extra update.
1248 -
1249 -(% class="box infomessage" %)
1250 1250  (((
1251 -apt update && apt install *dragino*
1252 -
1253 -wget -P /tmp/ [[http:~~/~~/repo.dragino.com/release/hp0c-packages/linux-image-current-draginohp0z_22.05.2_armhf.deb>>http://repo.dragino.com/release/hp0c-packages/linux-image-current-draginohp0z_22.05.2_armhf.deb]] && dpkg -i /tmp/[[linux-image-current-draginohp0z_22.05.2_armhf.deb>>http://repo.dragino.com/release/hp0c-packages/linux-image-current-draginohp0z_22.05.2_armhf.deb]]
1254 -)))
1255 -
1256 -
1257 -== (% data-sider-select-id="9b024263-b754-45b6-ac15-22f86a4e1436" %)12(% data-sider-select-id="0621ef51-7fc1-47ca-86ee-cc1f28f6754b" %).6  How to reset the built-in server(%%) ==
1258 -
1259 -
1260 -**1) Build-in The Things Network**
1261 -
1262 -Refer to this link to delete the Built-in server's device.
1263 -
1264 -[[Delete devices from Build-in The Things Network>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Delete%20devices%20from%20Build-in%20The%20Things%20Network/]]
1265 -
1266 -
1267 -**2) Build-in Chirpstack**
1268 -
1269 -Users need to click "Reset" on the Server~-~->NetServer interface, ChirpStack will be reset.
1270 -
1271 -[[image:image-20231106180846-5.png||height="310" width="668"]]
1272 -
1273 -
1274 -= (% data-sider-select-id="7e5e9cb1-c1dc-4ea9-a9f7-9da676c581a5" style="color:inherit; font-family:inherit; font-size:29px" %)13. Supports(%%) =
1275 -
1276 -
1277 -(((
1278 1278  If you are experiencing issues and can't solve them, you can send mail to [[support@dragino.com>>mailto:support@dragino.com]].
1279 1279  )))
1280 1280  
... ... @@ -1282,7 +1282,7 @@
1282 1282  With your question as detailed as possible. We will reply and help you in the shortest.
1283 1283  
1284 1284  
1285 -= (% data-sider-select-id="f8ca68c9-99ed-4795-97c5-3d0d259131e9" %)14. Reference(%%) =
881 += 11. Reference =
1286 1286  
1287 1287  
1288 1288  * Install Tago Core: Refer **Install Tago Core in LPS8v2** in[[ Instruction>>doc:Main.Tago\.IO.WebHome]].
... ... @@ -1291,7 +1291,7 @@
1291 1291  
1292 1292  )))
1293 1293  
1294 -= (% data-sider-select-id="a056b4ad-7d05-42b4-ad74-7a3134f8010a" %)15. Order Info(%%) =
890 += 12. Order Info =
1295 1295  
1296 1296  
1297 1297  (% style="color:#0000ff" %)**LPS8v2-XXX-YYY**
... ... @@ -1323,7 +1323,7 @@
1323 1323  More info about valid bands, please see [[EC25-E product page>>url:https://www.quectel.com/product/ec25.htm]].
1324 1324  
1325 1325  
1326 -= (% data-sider-select-id="a4433cd3-3bbc-4e6b-8b18-0bd2bc4d6904" %)16. Manufacturer Info(%%) =
922 += 13. Manufacturer Info =
1327 1327  
1328 1328  
1329 1329  **Shenzhen Dragino Technology Development co. LTD**
... ... @@ -1333,7 +1333,7 @@
1333 1333  LongCheng Street, LongGang District ; Shenzhen 518116,China
1334 1334  
1335 1335  
1336 -= (% data-sider-select-id="b353afd6-b0f5-48e5-a114-3b5062cbf0d1" %)17. FCC Warning(%%) =
932 += 14. FCC Warning =
1337 1337  
1338 1338  
1339 1339  (((
Delete Device.docx
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoye
Size
... ... @@ -1,1 +1,0 @@
1 -336.4 KB
Content
image-20231017111606-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -117.6 KB
Content
image-20231017112115-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -114.3 KB
Content
image-20231017114417-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -130.4 KB
Content
image-20231017115124-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -28.6 KB
Content
image-20231017115330-5.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -110.1 KB
Content
image-20231031162854-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -64.9 KB
Content
image-20231031162927-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -35.0 KB
Content
image-20231106175329-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -63.7 KB
Content
image-20231106175457-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -63.7 KB
Content
image-20231106175523-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -64.8 KB
Content
image-20231106180816-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -41.6 KB
Content
image-20231106180846-5.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -41.9 KB
Content
image-20231124113209-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoye
Size
... ... @@ -1,1 +1,0 @@
1 -198.7 KB
Content
image-20231201165904-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoye
Size
... ... @@ -1,1 +1,0 @@
1 -29.5 KB
Content
image-20231201170355-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoye
Size
... ... @@ -1,1 +1,0 @@
1 -70.2 KB
Content
image-20231207144627-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -182.9 KB
Content
image-20231207144758-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -51.0 KB
Content
image-20231207145210-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -104.4 KB
Content
image-20240203172853-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -24.5 KB
Content
image-20240318095605-1.jpeg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Edwin
Size
... ... @@ -1,1 +1,0 @@
1 -37.3 KB
Content
image-20240318095617-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Edwin
Size
... ... @@ -1,1 +1,0 @@
1 -32.9 KB
Content
image-20240318160845-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -36.5 KB
Content
image-20240416112509-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoye
Size
... ... @@ -1,1 +1,0 @@
1 -82.7 KB
Content
image-20240416112618-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoye
Size
... ... @@ -1,1 +1,0 @@
1 -128.5 KB
Content
image-20240416112649-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoye
Size
... ... @@ -1,1 +1,0 @@
1 -119.8 KB
Content
image-20240416112712-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoye
Size
... ... @@ -1,1 +1,0 @@
1 -29.6 KB
Content
image-20240416112948-5.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoye
Size
... ... @@ -1,1 +1,0 @@
1 -29.6 KB
Content
image-20240518145859-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -59.7 KB
Content
image-20240518145929-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -59.5 KB
Content
image-20240518152100-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -39.5 KB
Content
image-20240518152148-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -78.0 KB
Content
image-20240518154223-5.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -71.7 KB
Content
image-20240803095144-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -52.0 KB
Content
image-20240831151427-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -63.2 KB
Content
image-20240831152113-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -62.3 KB
Content
image-20240902092034-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -69.4 KB
Content
image-20241231151434-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -51.0 KB
Content
image-20241231151512-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -51.0 KB
Content
image-20241231151635-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -53.0 KB
Content
image-20241231151810-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -51.3 KB
Content
image-20241231151939-5.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -502.1 KB
Content
image-20241231152015-6.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -502.0 KB
Content
image-20241231153425-1.jpeg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -1.4 MB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0