Last modified by Kilight Cao on 2024/12/31 16:31
<
From version < 236.1 >
edited by Xiaoye
on 2023/07/21 14:48
To version < 326.1 >
edited by Kilight Cao
on 2024/09/02 08:55
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -LPS8v2 LoRaWAN Indoor Gateway User Manual
1 +LPS8v2 -- LoRaWAN Indoor Gateway User Manual
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Xiaoye
1 +XWiki.Kilight
Content
... ... @@ -8,7 +8,7 @@
8 8  
9 9  )))
10 10  
11 -**Table of Contents：**
11 +**Table of Contents:**
12 12  
13 13  {{toc/}}
14 14  
... ... @@ -18,7 +18,7 @@
18 18  
19 19  = 1. Introduction =
20 20  
21 -== 1.1 What is LPS8v2 ==
21 +== (% data-sider-select-id="66d5195f-ab1f-47c7-83cb-b027d0903e53" %)1.1 What is LPS8v2(%%) ==
22 22  
23 23  
24 24  (((
... ... @@ -81,7 +81,7 @@
81 81  ** Semtech UDP Packet Forwarder
82 82  ** LoRaWAN Basic Station
83 83  ** ChirpStack-Gateway-Bridge (MQTT)
84 -* Built-in (% style="color:#037691" %)**The Things Network**(%%) local LoRaWAN server
84 +* Built-in (% style="color:#037691" %)**ChirpStack**(%%) local LoRaWAN server
85 85  * Built-in  (% style="color:#037691" %)**Node-Red** (%%)local Application server
86 86  
87 87  == 1.4 LED Indicators ==
... ... @@ -96,11 +96,11 @@
96 96  
97 97  (% style="color:blue" %)**➢ SYS LED**(%%):  This RGB LED will show different colors in different states:
98 98  
99 - ✓ **SOLID GREEN:** The device is alive with a LoRaWAN server connection.
99 + ✓  **SOLID GREEN:** The device is alive with a LoRaWAN server connection.
100 100  
101 - ✓ **BLINKING GREEN:** a) Device has internet connection but no LoRaWAN Connection. or b) Device is in booting stage, in this stage, it will BLINKING GREEN for several seconds and then with BLINKING GREEN together
101 + ✓  **BLINKING GREEN:** a) Device has internet connection but no LoRaWAN Connection. or b) Device is in booting stage, in this stage, it will BLINKING GREEN for several seconds and then with BLINKING GREEN together
102 102  
103 - ✓** SOLID RED:** Device doesn't have an Internet connection.
103 + ✓**  SOLID RED:** Device doesn't have an Internet connection.
104 104  
105 105  (% style="color:blue" %)**➢ WIFI LED**(%%): This LED shows the WIFI interface connection status.
106 106  
... ... @@ -121,6 +121,18 @@
121 121   **LED status: ** ETH LED will SOLID BULE Until the restore is finished.
122 122  
123 123  
124 +(% style="color:red" %)**Note: Restoring factory Settings does not erase data from the LPS8-V2 built-in server**
125 +
126 +See this link for steps on how to clear data from the built-in server: **[[How to reset the built-in server>>http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/#H9.6A0Howtoresetthebuilt-inserver]]**
127 +
128 +
129 +When the gateway restores the factory settings is complete,
130 +
131 +The WiFi configuration will enable WiFi Access Point by default.
132 +
133 +The other configuration will be restored to the default configuration.
134 +
135 +
124 124  = 2. Quick Start =
125 125  
126 126  
... ... @@ -148,7 +148,6 @@
148 148  [[image:image-20230527085250-2.png||height="495" width="284"]]
149 149  
150 150  
151 -
152 152  ==== (% style="color:blue" %)**Method 2**(%%):  Connect via Ethernet with DHCP IP from the router ====
153 153  
154 154  
... ... @@ -163,7 +163,6 @@
163 163  [[image:image-20220622100129-1.png||height="332" width="1263"]]
164 164  
165 165  
166 -
167 167  ==== (% style="color:blue" %)**Method 3**(%%):  Connect via LPS8-V2 Fallback IP ====
168 168  
169 169  
... ... @@ -187,7 +187,7 @@
187 187  
188 188  Configure computer Ethernet port steps video: **[[attach:fallback ip.mp4||target="_blank"]]**
189 189  
190 -If you still can't access the LPS8-V2 fallback ip, follow this connection to debug : **[[Trouble Shooting>>http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/#H9.2A0FallbackIPdoesnotwork2Chowcanuserscheck]]**
200 +If you still can't access the LPS8-V2 fallback ip, follow this connection to debug : **[[Trouble Shooting>>http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/#H9.3A0FallbackIPdoesnotwork2Chowcanuserscheck]]**
191 191  
192 192  
193 193  3. In the PC, use IP address 172.31.255.254 to access the LPS8-V2 via Web or Console.
... ... @@ -195,7 +195,6 @@
195 195  [[image:image-20230111094247-2.png||height="619" width="1250"]]
196 196  
197 197  
198 -
199 199  ==== (% style="color:blue" %)**Method 4**(%%):  Connect via WiFi with DHCP IP from the router ====
200 200  
201 201  [[image:image-20220622100542-2.png||height="369" width="1256"]]
... ... @@ -235,7 +235,7 @@
235 235  
236 236  (% style="color:blue" %)**Password:   dragino**
237 237  
238 -[[image:image-20230106153501-1.png||height="367" width="894"]]
247 +[[image:image-20240318160845-1.png]]
239 239  
240 240  
241 241  == 2.2  Typical Network Setup ==
... ... @@ -298,6 +298,9 @@
298 298  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/LPS8N%20-%20LoRaWAN%20Gateway%20User%20Manual/WebHome/1657090932270-444.png?rev=1.1||alt="1657090932270-444.png"]]
299 299  
300 300  
310 +**Note: In most cases, the user simply types in the APN and checks the enable checkbox, without typing Pincode, Username, or Password settings.**
311 +
312 +
301 301  === 2.2.5  Check Internet connection ===
302 302  
303 303  
... ... @@ -421,25 +421,41 @@
421 421  
422 422  (((
423 423  Please see this instruction to know more detail and a demo for how to use of LoRaWAN Basic Station: __[[Use of LoRaWAN Basic Station - DRAGINO>>doc:Main.Use of LoRaWAN Basic Station.WebHome]]__
436 +
437 +
424 424  )))
425 425  
440 +== (% id="cke_bm_166450S" style="display:none" %) (%%)3.4 Forwarder ==
426 426  
427 -== 3.4 Network Settings ==
442 +=== 3.4.1 Forwarder~-~->MQTT Forwarder ===
428 428  
429 -=== 3.4.1 Network ~-~-> WiFi ===
430 430  
445 +In the latest version, MQTT Forwarder functionality has been added to the LPS8V2 gateway by default
446 +
447 +Users can configure the MQTT Forwarder on the **Forwarder~-~->MQTT** interface, and when the configuration is successful, it will forward the sensor data of the lorawan server chirpstack built in LPS8v2
448 +
449 +For a detailed example of this feature, see this link:**[[MQTT Forward Instruction - DRAGINO>>http://wiki.dragino.com/xwiki/bin/view/Main/MQTT%20Forward%20Instruction/#H3.3A0UseLoRaWANProtocolforcommunication--ForLPS8V2]]**
450 +
451 +(% class="wikigeneratedid" %)
452 +[[image:image-20240831152113-2.png]]
453 +
454 +
455 +== 3.5 Network Settings ==
456 +
457 +=== 3.5.1 Network ~-~-> WiFi ===
458 +
431 431  Users can configure the wifi WAN and enable Wifi Access Point on this interface
432 432  
433 433  [[image:image-20230619095946-1.png||height="332" width="827"]]
434 434  
435 435  
436 -=== 3.4.2 Network ~-~-> System Status ===
464 +=== 3.5.2 Network ~-~-> System Status ===
437 437  
438 438  
439 439  [[image:image-20220820134112-2.png||height="539" width="668"]]
440 440  
441 441  
442 -=== 3.4.3 Network ~-~-> Network ===
470 +=== 3.5.3 Network ~-~-> Network ===
443 443  
444 444  
445 445  In the **Network ~-~-> Network** interface, Users can set the Ethernet WAN static ip address.
... ... @@ -447,7 +447,7 @@
447 447  [[image:image-20230214093657-2.png||height="333" width="858"]]
448 448  
449 449  
450 -=== 3.4.4 Network ~-~-> Cellular ===
478 +=== 3.5.4 Network ~-~-> Cellular ===
451 451  
452 452  
453 453  In the **Network ~-~-> Cellular** interface, Users can Enable Cellular WAN and configure Celluar.
... ... @@ -466,18 +466,21 @@
466 466  
467 467  [[Reduce data method>>http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/#H8.3Howtoreducethe4gdataconsumed]]
468 468  
497 +(% class="wikigeneratedid" id="H5.MQTTForwarder" %)
498 +(% id="cke_bm_4823S" style="display:none" %)
469 469  
470 -== 3.5 System ==
471 471  
472 -=== 3.5.1 System ~-~-> System Overview ===
501 +== 3.6 System ==
473 473  
503 +=== 3.6.1 System ~-~-> System Overview ===
474 474  
505 +
475 475  Shows the system info:
476 476  
477 -[[image:image-20220917144512-5.png||height="618" width="853"]]
508 +[[image:image-20231031162854-1.png]]
478 478  
479 479  
480 -=== 3.5.2 System ~-~-> System General ===
511 +=== 3.6.2 System ~-~-> System General ===
481 481  
482 482  
483 483  In the **System-> System General** interface, Users can customize the configuration System Password and set Timezone.
... ... @@ -487,15 +487,29 @@
487 487  [[image:image-20230214094058-3.png]]
488 488  
489 489  
490 -=== 3.5.3 System ~-~-> Backup/Restore ===
521 +=== 3.6.3 System ~-~-> Backup/Restore ===
491 491  
492 492  
493 -[[image:image-20220917144725-6.png||height="208" width="869"]]
524 +[[image:image-20231031162927-2.png]]
494 494  
526 +=== 3.6.4 System ~-~-> Reboot / Reset ===
495 495  
496 -=== 3.5.4 System ~-~-> Remoteit ===
528 +In the **System-> Reboot / Reset** interface, users can can restart or reset the gateway.
497 497  
530 +ETH LED will SOLID BULE Until the restore is finished.
498 498  
532 +When the gateway restores the factory settings is complete,
533 +
534 +The WiFi configuration will enable WiFi Access Point by default.
535 +
536 +The other configuration will be restored to the default configuration.
537 +
538 +[[image:image-20240203172853-1.png||height="365" width="901"]]
539 +
540 +
541 +=== 3.6.5 System ~-~-> Remoteit ===
542 +
543 +
499 499  In the **System-> Remoteit** interface, users can configure the gateway to be accessed remotely via Remote.it.
500 500  
501 501  
... ... @@ -504,7 +504,7 @@
504 504  [[image:image-20221230092303-2.png]]
505 505  
506 506  
507 -=== 3.5.5 System ~-~-> Package Management ===
552 +=== 3.6.6 System ~-~-> Package Management ===
508 508  
509 509  
510 510  In the **System ~-~-> Package Management** interface, Users can check the current version of Core Packages.
... ... @@ -512,103 +512,114 @@
512 512  [[image:image-20230214094316-4.png]]
513 513  
514 514  
515 -= 4. Build-in Server =
560 +== 3.7 Logread ==
516 516  
562 +=== 3.7.1 LoRa Log ===
517 517  
518 -Since software version 0606,the default factory version of LPS8-V2 is installed with the built-in Applicant server: (% style="color:blue" %)**Node-Red**(%%), LoRaWAN Server: (% style="color:blue" %)**ChirpStack**(%%).
519 519  
520 -[[image:image-20230616175617-8.png||height="390" width="894"]]
565 +In the **Lograde ~-~-> LoRa Log page**, The users can view information about the gateway lora channel and the status of the IoT connection
521 521  
522 -[[image:image-20230616175558-7.png||height="362" width="894"]]
567 +[[image:image-20240416112509-1.png]]
523 523  
524 524  
570 +=== 3.7.2 Gateway Traffic ===
525 525  
526 -(% style="color:red" %)**Note:**
572 +In the **Lograde ~-~-> Gateway Traffic page**, The users can view sensor packages about Recent LoRa uplink/downlink/Join requests
527 527  
528 - **Path**: Server ~-~-> Network Server
574 +[[image:image-20240416112618-2.png||height="705" width="1122"]]
529 529  
530 - Server ~-~-> Application Server
531 531  
577 +=== 3.7.3 System Log ===
532 532  
533 -**Troubleshooting:**
579 +In the **Lograde ~-~-> System Log page**, The users can view information about the gateway system
534 534  
581 +[[image:image-20240416112649-3.png||height="820" width="1122"]]
535 535  
536 -**~ 1. URL does not jump properly**
537 537  
538 - For the ChirpStack, you can use the local IP address and the port is **8080** to access it.
584 +=== 3.7.4 Record Log ===
539 539  
540 - For the Node-Red, you can use the local IP address and the port is **1880** to access it.
586 +In the **Lograde ~-~-> Recod Log page**, The users can record the gateway curren running log.
541 541  
588 +[[image:image-20240416112712-4.png||height="319" width="1128"]]
542 542  
543 -== 4.1 LoRaWAN Network  Server ~-~- ChirpStack ==
544 544  
545 545  
546 -You can access the gateway's built-in LNS server of (% style="color:blue" %)**ChirpStack **(%%)via the URL( (% style="background-color:yellow" %)__**//http:~/~/<hostname>:8080 or http:~/~/<local-IPV4-address> //**__(%%)) in your browser.
592 += 4. Build-in Server =
547 547  
548 -Such as  (% style="background-color:yellow" %)__**//http:~/~/dragino-54ff12:8080  or http:~/~/<Local-IPV4-Address>//**__
594 +After the v1.7-230606 version, the LPS8-V2 default factory pre-installed the LoRaWAN Server: (% style="color:blue" %)**ChirpStack-V4**(%%), Application Server: (% style="color:blue" %)**Node-Red**(%%).
549 549  
550 550  
551 -Login account:
597 +== 1). LoRaWAN Network Server: (% style="color:blue" %)**ChirpStack-V4**(%%) ==
552 552  
553 -**Username : ** (% style="background-color:yellow" %)**admin**
599 +[[image:image-20231106180816-4.png||height="416" width="896"]]
554 554  
555 -**Password: ** ** (% style="background-color:#ffff00" %)admin(%%)**
601 +[[image:image-20231201165904-1.png||height="466" width="899"]]
556 556  
557 -[[image:image-20230616175332-6.png||height="519" width="1029"]]
603 +(% style="color:red" %)**Note:  The user can access the**(%%)** (% style="color:blue" %)ChirpStack-V4 (% style="color:red" %)via click the 'Launch' button, and the login account: admin/admin(%%)**
558 558  
605 +For more information on server operations see [[Register LPSV2 to the built-in Chirpstack>>||anchor="H2.3TheLPS8-V2isregisteredandconnectedtoTheThingsNetwork"]]
559 559  
560 560  
561 -=== 4.1.1 The LPS8-V2 is registered and connected to Built-in ChirpStack ===
562 562  
609 +== 2). Application Network Server: (% style="color:blue" %)**Node-Red**(%%) ==
563 563  
564 -Users need to set the Service Provider to (% style="color:blue" %)**Local Host/Build-in Server **(%%) and click "Save&Apply"
565 565  
566 -The registration steps are basically similar to [[LPS8-V2 is registered and connected to The Things Network>>||anchor="H2.3TheLPS8-V2isregisteredandconnectedtoTheThingsNetwork"]]
612 +[[image:image-20230616175558-7.png||height="362" width="894"]]
567 567  
568 -[[image:image-20230321092456-1.png]]
614 +[[image:image-20231201170355-2.png||height="536" width="899"]]
569 569  
616 +(% style="color:red" %)**Note:  The user can access the**(%%)** (% style="color:blue" %)Node-RED (% style="color:red" %)via click the 'Launch' button(%%)**
570 570  
571 571  
572 -== 4.2 Application Server ~-~- Node-Red ==
573 573  
620 +== **3). Troubleshooting:** ==
574 574  
575 -You can access the gateway's built-in AS server of (% style="color:blue" %)**Node-Red **(%%)via the URL((% style="background-color:yellow" %)__**//http:~/~/<hostname>:1880 or http:~/~/<local-IPV4-address>//**__(%%)) in your browser.
576 576  
623 +* (((
624 +=== ** If the URL does not jump properly.** ===
625 +)))
577 577  
578 -Such as (% style="background-color:yellow" %)__**//http:~/~/dragino-54ff12:1880  or http:~/~/<Local-IPV4-Address>//**__
627 + For the ChirpStack, you can use the local IP address and the port is **8080** to access it.
579 579  
629 + For the Node-Red, you can use the local IP address and the port is **1880** to access it.
580 580  
581 -[[image:image-20220725172124-3.png||height="610" width="843"]]
582 582  
632 +* (((
633 +=== ** How to install InfluxDB, Garfana.** ===
634 +)))
583 583  
636 + The LPS8V2 is not pre-installed with InfluxDB and Garfana, the users can install them, see [[InfluxDB>>http://wiki.dragino.com/xwiki/bin/view/Main/Armbian%20OS%20instruction/#H2.6HowtoinstallGrafanaandinfluxdb]]
584 584  
585 -=== **Using Node-Red, InfluxDB and Grafana** ===
586 586  
587 -The LPS8-V2 supports this combination, the default, Node-red is pre-installed but the InfluxDB and Grafana is not pre-installed.
639 +* (((
640 +=== ** How to upgrade the gateway node.js to the latest version.** ===
641 +)))
588 588  
643 + The user can upgrade nodejs, see [[Upgrade Nodejs>>http://wiki.dragino.com/xwiki/bin/view/Main/Armbian%20OS%20instruction/#H2.5Howtoupgradethenodejsversiontothelatest.]]
589 589  
590 -the users can refer to this link to install them.
591 591  
592 -[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Armbian%20OS%20instruction/#H2.6HowtoinstallGrafanaandinfluxdb>>http://wiki.dragino.com/xwiki/bin/view/Main/Armbian%20OS%20instruction/#H2.6HowtoinstallGrafanaandinfluxdb]]
646 +* (((
647 +=== ** How to batch register device on the built-in Chirpstack network server** ===
648 +)))
593 593  
650 + The user can register devices in batch on the gateway Web UI, see [[Batch Register>>http://wiki.dragino.com/xwiki/bin/view/Main/Notes%20for%20ChirpStack/#H11.A0HowtouseChirpstackAPItobatchregisterSensorNode2FGatewayinChistapstackServer]]
594 594  
595 -=== **Upgrade the node.js** ===
596 596  
597 -By default, the LPS8-V2 node.js uses the pre-install version v12 which is due to Debian the ultra-stable via ultra-old.
653 +* (((
654 +=== ** Why my gateway is not Chirpstack?** ===
655 +)))
598 598  
657 + After June '23, the default factory LPS8V2 pre-installed Chirpstack-V4 instead of The Things Stack, the users can migrate to Chistack-V4, see **[[Change TTN Stack v3 to ChirpStack>>http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/#H9.2Build-inTheThingsNetworkmigratetoChirpStack]]**
599 599  
600 -the users can refer to this link to upgrade them.
601 601  
602 -[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Armbian%20OS%20instruction/#H2.5Howtoupgradethenodejsversiontothelatest.>>http://wiki.dragino.com/xwiki/bin/view/Main/Armbian%20OS%20instruction/#H2.5Howtoupgradethenodejsversiontothelatest.]]
660 +* (((
661 +=== ** How to disable the built-in server** ===
662 +)))
603 603  
604 -
605 -== 4.3 How to disable the built-in server ==
606 -
607 -
608 -Use the following commands to start and stop the TTNv3 service:
609 -
610 610  (% class="box infomessage" %)
611 611  (((
666 +Use the following commands to start and stop the TTNv3 service:**     **
667 +
612 612  **# start**
613 613  systemctl start ttnstack
614 614  
... ... @@ -622,10 +622,10 @@
622 622  systemctl disable ttnstack
623 623  )))
624 624  
625 -Use the following commands to start and stop the Node-Red service:
626 -
627 627  (% class="box infomessage" %)
628 628  (((
683 +Use the following commands to start and stop the Node-Red service:
684 +
629 629  **# start**
630 630  systemctl start nodered
631 631  
... ... @@ -640,36 +640,44 @@
640 640  )))
641 641  
642 642  
643 -== 4.4 How to use ChirpStack on LPS8-V2 ==
699 +* (((
700 +=== ** How to choose the Chirpstack server frequency SubBand** ===
701 +)))
644 644  
703 +**~ ** The user has to choose a SubBand if using CN470, US915, AU915, or AS923.
645 645  
646 -By default, the built-in LoRaWAN network server used on LPS8v2 is TTNv3, so users need follow this link to install chirpstack:
705 + Note: Since the subbands of the Chirpstack are counted from 0, us915_1 of the Chirpstack is equal to US915 FSB2, so if your LoRa Rdio is using the US915 FSB2 you have to choose the us915_1 as the Chirpstack FSB.
647 647  
648 -**[[Build-in The Things Network migrate to ChirpStack>>http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/#H9.2Build-inTheThingsNetworkmigratetoChirpStack]]**
707 +[[image:image-20230602140406-3.png||height="480" width="918"]]
649 649  
650 650  
651 -=== 4.4.1 How do users choose the chirpstack server frequency SubBand ===
710 +When the configuration is complete, click** "Save&Apply"**.
652 652  
653 653  
654 -On the **Server ~-~-> Network Server** interface, choose the frequency Plan first.
713 +(% style="color:red" %)**Note:**(%%) When adding the device profile, the selected Region configuration is also calculated from 0, so setting it to us915_1 corresponds to US915 Sub Band 2.
655 655  
656 -If the frequency Plan used is CN470, US915, AU915, or AS923, the user needs to choose a frequency sub-band, because the frequency Sub Band of ChirpStack starts from 0, so for example, us915_1 corresponds to the actual frequency US915_2.
715 +[[image:image-20230602143122-4.png||height="511" width="983"]]
657 657  
658 -[[image:image-20230602140406-3.png||height="480" width="918"]]
659 659  
660 660  
661 -When the configuration is complete, click** "Save&Apply"**.
719 += 5. Watch Dog =
662 662  
663 663  
664 -(% style="color:red" %)**Note:**(%%) When adding device profile, the selected Region configuration is also calculated from 0, so setting it to us915_1 corresponds to US915 Sub Band 2.
722 +The watchdog will guard the LPS8V2 to avoid the need to perform a reboot manually after down occurs
665 665  
666 -[[image:image-20230602143122-4.png||height="511" width="983"]]
667 667  
725 +LPS8-V2 supports the Watch Dog but is not enabled by the previous releases(2023-11-24 )
668 668  
669 -= 5. How the LPS8-V2 connects to Chirpstack via gateway-bridge =
727 +The uses can be via the below method to enable Watch Dog:
670 670  
729 +(% class="box infomessage" %)
730 +(((
731 +wget -P /tmp/ http:~/~/repo.dragino.com/release/tool/watchdog/enable_watchdog.sh && chmod +x /tmp/enable_watchdog.sh && /tmp/enable_watchdog.sh
732 +)))
671 671  
734 +[[image:image-20231124113209-1.png||height="470" width="1157"]]
672 672  
736 +
673 673  = 6. How users can access LPS8-V2 using serial USB =
674 674  
675 675  
... ... @@ -723,7 +723,6 @@
723 723  
724 724  1). Using the Linux command to upgrade the system
725 725  
726 -
727 727  (% class="box infomessage" %)
728 728  (((
729 729  **apt update && apt install *dragino***
... ... @@ -732,68 +732,339 @@
732 732  
733 733  2). Upgrade the system via the Web page button of "Manual Update"
734 734  
798 +(% style="color:red" %)**Note: this method needs about 10 mins, so you will get the log after 10 mins.  **
735 735  
736 -**Note: this method needs about 10 mins, so you will get the log after 10 mins.  **
737 -
738 738  [[image:image-20230607093849-1.png]]
739 739  
740 740  
803 += (% data-sider-select-id="f31494a0-5f58-4b5c-820e-9cb1be76d96f" %)8 How do I view gateway logs(%%) =
741 741  
742 -= 8. FAQ =
805 +=== (% data-sider-select-id="2c782a3d-7138-45c4-bbdf-09c0e27ef896" %)8.1 LoRaWAN Log:(%%) ===
743 743  
744 -== 8.1 How to change Hostname ==
745 745  
808 +==== Semtech UDP Log : ====
746 746  
747 -By default, Hostname is dragino-xxxxxx,If the user needs to change the hostname, the user needs to access the linux console of LPS8v2 and enter the following command:
810 +When the gateway starts LoRaWAN Semtech UDP, users can check the logs of the Semtech UDP in the **LogRead ~-~-> System Log** interface
748 748  
812 +[[image:image-20231017112115-2.png||height="611" width="821"]]
813 +
814 +
815 +==== Station Log: ====
816 +
817 +When the gateway starts Basic Station, users can check the logs of the station in the **LogRead ~-~-> System Log** interface
818 +
819 +[[image:image-20231017111606-1.png||height="622" width="821"]]
820 +
821 +
822 +=== (% data-sider-select-id="de76f982-b2e5-4327-aab4-8890814f5f53" %)8.2  4G Log(%%) ===
823 +
824 +
825 +User needs to access the Linux console of the gateway and enter the following command:
826 +
749 749  (% class="box infomessage" %)
750 750  (((
751 -hostnamectl set-hostname dragino-123456
829 +cat /var/log/qmilog.txt
752 752  )))
753 753  
754 -[[image:image-20230517102429-1.png]]
832 +[[image:image-20231017114417-3.png||height="543" width="679"]]
755 755  
756 -After the configuration is complete, run "reboot" to restart the gateway.
757 757  
835 +LPS8v2 use **quectel-CM** linux drive for dial up. The manual of this driver can be found here: [[**quectel-CM driver user manual**>>https://www.dropbox.com/scl/fi/73n2jl2c5r8h4i187to4n/Quectel_WCDMA_LTE_Linux_USB_Driver_User_Guide_V1.9-20190212.pdf?rlkey=j8834bw38d4neieisg54zngu9&st=kjsd4zx4&dl=0]].
758 758  
759 -== 8.2 Build-in The Things Network migrate to ChirpStack ==
837 +Below are some commands as reference:
760 760  
839 +>Usage:  /usr/bin/quectel-CM [options]
840 +> -s [apn [user password auth]]  Set apn/user/password/auth get from your network provider. auth: 1~~pap, 2~~chap
841 +> -p pincode Verify sim card pin if sim card is locked
842 +> -p [quectel-][qmi|mbim]-proxy  Request to use proxy
843 +> -f logfilename Save log message of this program to file
844 +> -u usbmonlog filename  Save usbmon log to file
845 +> -i interface Specify which network interface to setup data call when multi-modems exits
846 +> -4 Setup IPv4 data call (default)
847 +> -6 Setup IPv6 data call
848 +> -k pdn Specify which pdn to hangup data call (by send SIGINT to 'quectel-CM -n pdn')
849 +> -m iface-idx Bind QMI data call to wwan0_<iface idx> when QMAP used. E.g '-n 7 -m 1' bind pdn-7 data call to wwan0_1
850 +> -b Enable network interface bridge function (default 0)
851 +> -v Verbose log mode, for debug purpose.[Examples]
852 +>Example 1: /usr/bin/quectel-CM
853 +>Example 2: /usr/bin/quectel-CM -s 3gnet
854 +>Example 3: /usr/bin/quectel-CM -s 3gnet -v
761 761  
762 -Migrate guide:
763 763  
764 -**1. Ensure that the gateway is in good network condition, Recommended use of ETH.**
765 765  
766 -**2. On the Server ~-~-> Network Server interface, click "Management"**
858 +=== (% data-sider-select-id="ec43d85c-19ec-48b0-a4fc-0ecd76f17fc4" %)8.3 Dmesg Log(%%) ===
767 767  
768 -[[image:image-20230616162454-1.png]]
769 769  
861 +Users can check the logs of the Dmesg in the **LogRead ~-~-> System Log** interface:
770 770  
771 -**3. Click "Migrate-Chirpstack"**
863 +[[image:image-20231017115330-5.png||height="565" width="740"]]
772 772  
773 -[[image:image-20230616162742-2.png]]
774 774  
866 +=== (% data-sider-select-id="3a977a3e-9417-40fa-bdfb-2544a88744a9" %)8.4 Record Log(%%) ===
775 775  
776 -**4. Strat Install **
777 777  
869 +Users can record DMESG logs and LoRaWAN logs on the **LogRead ~-~->Record Log** interface
778 778  
779 -Click start Install and wait until the migration succeeds
871 +[[image:image-20231017115124-4.png||height="215" width="880"]]
780 780  
781 -[[image:image-20230616162934-3.png]]
782 782  
874 +=== (% data-sider-select-id="b988f832-4b37-4a61-b951-ff2138ad9cba" %)8.5 View gateway logs via Linux Command(%%) ===
783 783  
784 -**5.Migration complete check result**
785 785  
786 -[[image:image-20230616174526-4.png||height="706" width="983"]]
877 +**Semtech UDP Log :**
787 787  
879 +(% class="box infomessage" %)
880 +(((
881 +**journalctl -u draginofwd -f**
882 +)))
788 788  
789 -[[image:image-20230616180004-9.png]]
884 +[[image:image-20231207144627-1.png||height="371" width="1017"]]
790 790  
791 791  
792 -== 8.3 How to reduce the 4g data consumed ==
887 +**Station Log:**
793 793  
794 -1). The gateway will check the network via ping 1.1.1.1/8.8.8.8 which will consume a lot of data, you can set the interval time to reduce data consume.
889 +(% class="box infomessage" %)
890 +(((
891 +**tail -f /var/log/station.log **
892 +)))
795 795  
894 +[[image:image-20231207144758-2.png||height="132" width="1022"]]
796 796  
896 +
897 +**Dmesg Log:**
898 +
899 +(% class="box infomessage" %)
900 +(((
901 +**dmesg**
902 +)))
903 +
904 +[[image:image-20231207145210-3.png||height="310" width="1021"]]
905 +
906 +
907 +
908 +(% data-sider-select-id="65e92cfb-62df-4513-8469-b74edd72dea5" %)
909 += (% data-sider-select-id="ce97a758-4348-4c0c-86eb-412b6b8d3996" %)9. More Services(%%) =
910 +
911 +== (% data-sider-select-id="6b164b64-51ae-4144-8ffd-5cd725b3bb5f" %)9.1 NTP Service/Time Synchronization(%%) ==
912 +
913 +The gateway time sync service is provided by chrony service
914 +
915 +
916 +=== 1). Modify the NTP server address: ===
917 +
918 +(% class="box infomessage" %)
919 +(((
920 +Configuration file path:  /etc/chrony/chrony.conf
921 +)))
922 +
923 +
924 +=== 2). Start/Stop/Enable/Disable NTP service: ===
925 +
926 +(% class="box infomessage" %)
927 +(((
928 +systemctl start chrony
929 +\\systemctl stop chrony
930 +\\systemctl disable chrony
931 +\\systemctl enable chrony
932 +)))
933 +
934 +
935 +(% data-sider-select-id="61881d06-3f91-437c-8b64-7032dea3c970" %)
936 += (% data-sider-select-id="fb64fcfa-81b6-41b5-ae81-81d94960d7dd" %)10. More features(%%) =
937 +
938 +(% data-sider-select-id="692f00f1-a7cc-4954-ac62-0a5dddb0a0c6" %)
939 +== (% data-sider-select-id="ec6a5e23-ba91-46d9-8042-1e4c6a7b3b36" %)10.1 Chirpstack MQTT Forwarder(%%) ==
940 +
941 +
942 +ChirpStack MQTT Forwarder is a MQTT packet forwarder for LoRa gateways. By default it forwards packets in Protobuf binary format, optionally it can be configured to use JSON encoding for debugging. In contrast to the ChirpStack Gateway Bridge, this component must always be installed on the gateway.
943 +
944 +
945 +(% data-sider-select-id="d2b54844-aad8-4198-9f17-841cd68db9b3" %)
946 +=== (% data-sider-select-id="fb64fcfa-81b6-41b5-ae81-81d94960d7dd" %)10(% data-sider-select-id="0870eb11-ff25-47fc-9e3c-80a68bbf3933" %).1.1 Configure Packet Forwarder(%%) ===
947 +
948 +In the Dragino web-interface, you must configure the Packet Forwarder such that it forwards to localhost on port 1700.
949 +
950 +(% data-sider-select-id="48576a4e-42ef-4ac9-83b4-122fc10c6629" %)
951 +By default, the web-interface can be accessed by entering the following URL in your browser: (% data-sider-select-id="c2683c51-0bf8-4ac5-87be-c50edacc8f4b" %)**http:~/~/GATEWAY-IP-ADDRESS**(%%) (replace GATEWAY-IP-ADDRESS by the actual IP address of your gateway). The default credentials are root / dragino.
952 +
953 +* In the **LoRaWAN** menu, click **LoRaWAN ~-~- Semtech UDP**
954 +* Configure the following settings:
955 +** **Service Provider:** //Custom / Private LoRaWAN//
956 +** **Server Address:** localhost
957 +** **Uplink Port:** 1700
958 +** **Downlink Port:** 1700
959 +* Click **Save & Apply**
960 +
961 +[[image:image-20240518145929-2.png||height="652" width="727"]]
962 +
963 +
964 +(% data-sider-select-id="716df9b1-d844-4797-bce9-9b1adf49b072" %)
965 +=== (% data-sider-select-id="fb64fcfa-81b6-41b5-ae81-81d94960d7dd" %)10(% data-sider-select-id="ffba644f-a9d5-4e93-a9da-9f9e49d596d9" %).1.2 Install ChirpStack MQTT Forwarder(%%) ===
966 +
967 +
968 +(% data-sider-select-id="2a752131-c23e-4da4-b142-5880dd688c39" %)
969 +(% data-sider-select-id="833bbe42-c175-4e13-ab7a-c8abc30378d0" %)**SSH login**
970 +
971 +First you must login into the gateway using SSH:
972 +
973 +(% class="box infomessage" data-sider-select-id="608a94b0-8dee-453d-9433-5fe12c6559e5" %)
974 +(((
975 +ssh root@GATEWAY-IP-ADDRESS
976 +)))
977 +
978 +(% data-sider-select-id="63adc977-8227-4585-ab1d-eea44a01c34c" %)
979 +The default password is: (% data-sider-select-id="5fad2844-9bd3-49e2-979b-ffd184b923cf" %)**dragino**(%%).
980 +
981 +
982 +(% data-sider-select-id="216fb9b4-6cee-4cb6-8b71-0a9cda3bd96a" %)
983 +(% data-sider-select-id="914750d6-03c5-48fe-ad27-49e99d95d877" %)**Download **(% data-sider-select-id="94e274ee-d341-40dc-8ca8-dc3c3b4c4981" %)**package**
984 +
985 +(% data-sider-select-id="f95485e3-b535-4ea2-b0aa-0c46b5254782" %)
986 +Use the following commands to download the latest version of the ChirpStack MQTT Forwarder package:
987 +
988 +(% class="box infomessage" data-sider-select-id="ab1338ab-a215-4185-8552-1efd6e067858" %)
989 +(((
990 +cd /tmp
991 +wget https:~/~/artifacts.chirpstack.io/downloads/chirpstack-mqtt-forwarder/chirpstack-mqtt-forwarder_4.3.0_linux_armhf.deb
992 +)))
993 +
994 +
995 +(% data-sider-select-id="e59f1bad-427f-47b8-bc97-a818490576c4" %)
996 +(% data-sider-select-id="1b512eaf-c564-4835-afac-548b9a6a7045" %)**Install **
997 +
998 +Use the dpkg package-manager to install the downloaded package. Example:
999 +
1000 +(% class="box infomessage" data-sider-select-id="7e7ff0cf-c367-4ff0-9387-f4eb82f3c89e" %)
1001 +(((
1002 +dpkg -i chirpstack-mqtt-forwarder_4.3.0_linux_armhf.deb
1003 +)))
1004 +
1005 +[[image:image-20240518152148-4.png]]
1006 +
1007 +
1008 +(% data-sider-select-id="69e4a485-6ea8-46e7-97a3-8666bc9423a7" %)
1009 +**Configuration**
1010 +
1011 +To connect the ChirpStack MQTT Forwarder to your MQTT broker, you must update the ChirpStack MQTT Forwarder configuration file.
1012 +
1013 +(% data-sider-select-id="e98443ef-dcc1-4be1-ad3e-ec31b0a580b4" %)
1014 +This file is located at: (% data-sider-select-id="60301edc-5082-44e9-a91a-688327092116" %)**/etc/chirpstack-mqtt-forwarder/chirpstack-mqtt-forwarder.toml**
1015 +
1016 +
1017 +**ChirpStack MQTT Forwarder Setting:**
1018 +
1019 +(% class="box" data-sider-select-id="1d70062d-64ab-410b-bd8e-476c73d5dd70" %)
1020 +(((
1021 +topic_prefix  ~-~->  This corresponds to the frequency of the ChirpStack server
1022 +
1023 +server  ~-~->  Fill in the ChirpStack server address, Example: tcp:~/~/10.130.2.15:1883
1024 +)))
1025 +
1026 +username,password,ca_cert,tls_cert,tls_key parameters should be set as required.
1027 +
1028 +
1029 +Use commands to modify configuration files:
1030 +
1031 +(% class="box infomessage" data-sider-select-id="d552b27f-cfd2-4f5a-9b7f-b627f5dd3387" %)
1032 +(((
1033 +vim /etc/chirpstack-mqtt-forwarder/chirpstack-mqtt-forwarder.toml
1034 +)))
1035 +
1036 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/LPS8N%20-%20LoRaWAN%20Gateway%20User%20Manual/WebHome/image-20240518141059-6.png?rev=1.1||alt="image-20240518141059-6.png"]]
1037 +
1038 +
1039 +**(Re)start and stop commands**
1040 +
1041 +Use the following commands to (re)start and stop the ChirpStack MQTT Forwarder service:
1042 +
1043 +(% class="box infomessage" data-sider-select-id="61c3c343-2cb9-4b07-8741-5d5da2d88ec3" %)
1044 +(((
1045 +# start
1046 +
1047 +(% data-sider-select-id="5482a31e-3aa0-403c-aec5-117839958068" %)
1048 +systemctl start chirpstack-mqtt-forwarder
1049 +
1050 +# stop
1051 +
1052 +systemctl stop chirpstack-mqtt-forwarder
1053 +
1054 +# restart
1055 +
1056 +systemctl restart chirpstack-mqtt-forwarder
1057 +)))
1058 +
1059 +(% data-sider-select-id="1cea423f-9653-47e6-8022-aadcb684f191" %)
1060 +(% data-sider-select-id="f385e712-68bc-48fd-8b94-67a0c7e7cb70" %)**Note: If the LPS8v2 built-in server is running, it will cause a port conflict**
1061 +
1062 +
1063 +**Check result**
1064 +
1065 +(% data-sider-select-id="43d1d40a-2620-4547-b00d-f78dd5427215" %)
1066 +Use "** journalctl -u chirpstack-mqtt-forwarder -f(% data-sider-select-id="ab74df8a-b859-4afa-9c26-d0807e860e6c" %) (%%)**" to check the operation of ChirpStack MQTT Forwarder.
1067 +
1068 +[[image:image-20240518154223-5.png]]
1069 +
1070 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/LPS8N%20-%20LoRaWAN%20Gateway%20User%20Manual/WebHome/image-20240518143050-8.png?width=1170&height=702&rev=1.1||alt="image-20240518143050-8.png"]]
1071 +
1072 +
1073 +== (% data-sider-select-id="de90793f-d833-4885-8b59-d0880f7256e6" %)10.2 As a Data-only hotspot connect the helium blockchain(%%) ==
1074 +
1075 +
1076 +(% class="box infomessage" %)
1077 +(((
1078 +(% data-sider-select-id="3359233b-fcc9-4415-9bee-4151919fbb2e" %)
1079 +apt update && apt install helium-gateway
1080 +)))
1081 +
1082 +
1083 +
1084 += (% data-sider-select-id="20d4ea6b-7328-46c6-bc97-f0050cfe382e" %)11. FAQ(%%) =
1085 +
1086 +== (% data-sider-select-id="9fbcac50-3c87-43d9-8611-8d311fcb7820" %)11.1 How to change Hostname(%%) ==
1087 +
1088 +
1089 +By default, Hostname is dragino-xxxxxx,If the user needs to change the hostname, the user needs to access the linux console of LPS8v2 and enter the following command:
1090 +
1091 +(% class="box infomessage" %)
1092 +(((
1093 +hostnamectl set-hostname dragino-123456
1094 +)))
1095 +
1096 +[[image:image-20230517102429-1.png]]
1097 +
1098 +After the configuration is complete, run "reboot" to restart the gateway.
1099 +
1100 +
1101 +== (% data-sider-select-id="20d4ea6b-7328-46c6-bc97-f0050cfe382e" %)11(% data-sider-select-id="62cdc3f4-fb6f-4e4d-92a5-60449c8b462f" %).2 Build-in The Things Network migrate to ChirpStack(%%) ==
1102 +
1103 +
1104 +Migrate guide:
1105 +
1106 +To stabilize the completion of the migration, The users can migrate in one of the following ways
1107 +
1108 +**Method 1. Using the Linux shell, **
1109 +
1110 +**Method 2. Flash a new image with the Chirpstack**
1111 +
1112 +
1113 +=== Method 1: Using the Linux shell ===
1114 +
1115 +(% class="box infomessage" %)
1116 +(((
1117 +wget -P /tmp [[http:~~/~~/repo.dragino.com/release/tool/chirpstack/migrate_chirpstack>>http://repo.dragino.com/release/tool/chirpstack/migrate_chirpstack]] && chmod +x /tmp/migrate_chirpstack && /tmp/migrate_chirpstack
1118 +)))
1119 +
1120 +
1121 +=== Method 2: Flash a new image ===
1122 +
1123 +Image flash steps: [[How to flash a new image(OS) to the gateway(LPS8V2)>>http://wiki.dragino.com/xwiki/bin/view/Main/Armbian%20OS%20instruction/#H2.3A0Howtoflashanewimage28OS29tothegateway28LPS8V229]]
1124 +
1125 +
1126 +== (% data-sider-select-id="20d4ea6b-7328-46c6-bc97-f0050cfe382e" %)11(% data-sider-select-id="b2a44672-8abb-425d-a823-f2faa334cdb7" %).3 How to reduce the 4g data consumed(%%) ==
1127 +
1128 +
1129 +1). The gateway will check the network via ping 1.1.1.1/8.8.8.8 which will consume a lot of data, you can set the interval time to reduce data consume.
1130 +
797 797  [[image:image-20230719100239-1.png||height="724" width="994"]]
798 798  
799 799  
... ... @@ -801,18 +801,53 @@
801 801  
802 802  [[image:image-20230719100332-2.png]]
803 803  
1138 +
804 804  3. Disable the auto-update:
805 805  
806 806  [[image:image-20230719100419-3.png||height="458" width="995"]]
807 807  
808 808  
1144 +== (% data-sider-select-id="20d4ea6b-7328-46c6-bc97-f0050cfe382e" %)11(% data-sider-select-id="457c03ce-1aaa-44c6-bf8e-0298ca8045e4" %).4 How to change built-in LoRaWAN Server from ChirpStack v4 to TTN Stack v3.(%%) ==
809 809  
810 810  
811 -= 9. Trouble Shooting =
1147 +By default, the LPS8v2's built-in server is ChirpStack v4,
812 812  
813 -== 9.1  I can't log in to the built-in Server TTN Stack which shows '**Login failed**'. ==
1149 +If the user needs to change the built-in server from ChirpStack v4 to TTN Stack v3, the User needs to download the image and flash it to the LPS8v2 gateway:
814 814  
1151 +[[https:~~/~~/www.dropbox.com/scl/fi/qwtaw4i4dqonzramr93e4/dragino-LPS8V2-TTN-231124.rar?rlkey=nrftlkd1h8en6j07vzbhpj9ui&dl=0>>https://www.dropbox.com/scl/fi/qwtaw4i4dqonzramr93e4/dragino-LPS8V2-TTN-231124.rar?rlkey=nrftlkd1h8en6j07vzbhpj9ui&dl=0]]
815 815  
1153 +
1154 +Image flash steps: [[How to flash a new image(OS) to the gateway(LPS8V2)>>http://wiki.dragino.com/xwiki/bin/view/Main/Armbian%20OS%20instruction/#H2.3A0Howtoflashanewimage28OS29tothegateway28LPS8V229]]
1155 +
1156 +
1157 +== (% data-sider-select-id="20d4ea6b-7328-46c6-bc97-f0050cfe382e" %)11(% data-sider-select-id="457c03ce-1aaa-44c6-bf8e-0298ca8045e4" %).5 (%%)How to check my USB port dev/tty after i plug in USB device. ==
1158 +
1159 +
1160 +When an external USB device is connected to LPS8v2, the user can access the Linux console of the LPS8v2 gateway and run the following command to check the USB port dev/tty:
1161 +
1162 +(% class="box infomessage" %)
1163 +(((
1164 +dmesg
1165 +)))
1166 +
1167 +[[image:image-20240803095144-1.png]]
1168 +
1169 +
1170 +
1171 +== (% data-sider-select-id="20d4ea6b-7328-46c6-bc97-f0050cfe382e" %)11(% data-sider-select-id="82550df9-987d-4f58-9877-86a0c5e621a4" %).6 DIN Mount Reference:(%%) ==
1172 +
1173 +
1174 +[[image:image-20240318095605-1.jpeg||height="472" width="472"]]
1175 +
1176 +[[image:image-20240318095617-2.png]]
1177 +
1178 +
1179 +
1180 +
1181 += (% data-sider-select-id="9b024263-b754-45b6-ac15-22f86a4e1436" %)12. Trouble Shooting(%%) =
1182 +
1183 +== (% data-sider-select-id="cb7a0b2f-4144-4f58-86d0-64a15944840e" %)12.1  I can't log in to the built-in Server TTN Stack which shows '**Login failed**'.(%%) ==
1184 +
816 816  [[image:image-20220920135918-1.png]]
817 817  
818 818  
... ... @@ -828,7 +828,7 @@
828 828  [[image:image-20220920141936-2.png]]
829 829  
830 830  
831 -== 9.2  The built-in TTN status is "Not Running" and the URI is "dragino-123456". How users fix this problem ==
1200 +== (% data-sider-select-id="9b024263-b754-45b6-ac15-22f86a4e1436" %)12(% data-sider-select-id="f34b4950-25aa-4a6d-a2b4-4af0ec0010a7" %).2  The built-in TTN status is "Not Running" and the URI is "dragino-123456". How users fix this problem(%%) ==
832 832  
833 833  
834 834  When this problem occurs, click "**Update To DEFAULT**" ,this problem will be fixed.
... ... @@ -836,13 +836,13 @@
836 836  [[image:image-20230508171607-1.png]]
837 837  
838 838  
839 -== 9.3  Fallback IP does not work, how can users check ==
1208 +== (% data-sider-select-id="9b024263-b754-45b6-ac15-22f86a4e1436" %)12(% data-sider-select-id="a7b8cd40-2ec5-4b4b-8220-d32ce0a303a0" %).3  Fallback IP does not work, how can users check(%%) ==
840 840  
841 841  
842 842  When the computer has completed the above fallback IP configuration,the LPS8v2 Web UI is still not accessible via fallback IP.
843 843  
844 844  
845 -**1.Check whether the configuration is correct**
1214 +**~1. Check whether the configuration is correct**
846 846  
847 847  Run the CMD command to ipconfig and ping 172.31.255.254.
848 848  
... ... @@ -858,7 +858,7 @@
858 858  If the firewall is not down, this will affect access to the gateway.
859 859  
860 860  
861 -== 9.4  Click "Manual_Update", why there is no response? ==
1230 +== (% data-sider-select-id="9b024263-b754-45b6-ac15-22f86a4e1436" %)12(% data-sider-select-id="b7eec45b-ad8c-4621-a815-f457810d25f4" %).4  Click "Manual_Update", why there is no response?(%%) ==
862 862  
863 863  
864 864  When you click "Manual_Update", the gateway will finish updating within 10 minutes and display the update log.
... ... @@ -867,22 +867,39 @@
867 867  [[image:image-20230527090555-3.png||height="660" width="832"]]
868 868  
869 869  
870 -== 9.4 Why the LPS8V2's Access Point does not do not appear & Fallback IP unable to access ==
1239 +== (% data-sider-select-id="9b024263-b754-45b6-ac15-22f86a4e1436" %)12(% data-sider-select-id="ac1f33b3-1f28-477d-880c-534ac36adcbe" %).5  Why the LPS8V2's Access Point does not do not appear & Fallback IP unable to access(%%) ==
871 871  
1241 +
872 872  Earlier versions of the LPS8V2 which missing the AP driver and not installed the fallback package, so the users have to do an extra update.
873 873  
874 -
875 875  (% class="box infomessage" %)
876 876  (((
877 -apt update && apt install dragino-fallback
1246 +apt update && apt install *dragino*
878 878  
879 879  wget -P /tmp/ [[http:~~/~~/repo.dragino.com/release/hp0c-packages/linux-image-current-draginohp0z_22.05.2_armhf.deb>>http://repo.dragino.com/release/hp0c-packages/linux-image-current-draginohp0z_22.05.2_armhf.deb]] && dpkg -i /tmp/[[linux-image-current-draginohp0z_22.05.2_armhf.deb>>http://repo.dragino.com/release/hp0c-packages/linux-image-current-draginohp0z_22.05.2_armhf.deb]]
880 880  )))
881 881  
882 882  
883 -= (% style="color:inherit; font-family:inherit; font-size:29px" %)10. Supports(%%) =
1252 +== (% data-sider-select-id="9b024263-b754-45b6-ac15-22f86a4e1436" %)12(% data-sider-select-id="0621ef51-7fc1-47ca-86ee-cc1f28f6754b" %).6  How to reset the built-in server(%%) ==
884 884  
885 885  
1255 +**1) Build-in The Things Network**
1256 +
1257 +Refer to this link to delete the Built-in server's device.
1258 +
1259 +[[Delete devices from Build-in The Things Network>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Delete%20devices%20from%20Build-in%20The%20Things%20Network/]]
1260 +
1261 +
1262 +**2) Build-in Chirpstack**
1263 +
1264 +Users need to click "Reset" on the Server~-~->NetServer interface, ChirpStack will be reset.
1265 +
1266 +[[image:image-20231106180846-5.png||height="310" width="668"]]
1267 +
1268 +
1269 += (% data-sider-select-id="7e5e9cb1-c1dc-4ea9-a9f7-9da676c581a5" style="color:inherit; font-family:inherit; font-size:29px" %)13. Supports(%%) =
1270 +
1271 +
886 886  (((
887 887  If you are experiencing issues and can't solve them, you can send mail to [[support@dragino.com>>mailto:support@dragino.com]].
888 888  )))
... ... @@ -891,7 +891,7 @@
891 891  With your question as detailed as possible. We will reply and help you in the shortest.
892 892  
893 893  
894 -= 11. Reference =
1280 += (% data-sider-select-id="f8ca68c9-99ed-4795-97c5-3d0d259131e9" %)14. Reference(%%) =
895 895  
896 896  
897 897  * Install Tago Core: Refer **Install Tago Core in LPS8v2** in[[ Instruction>>doc:Main.Tago\.IO.WebHome]].
... ... @@ -900,7 +900,7 @@
900 900  
901 901  )))
902 902  
903 -= 12. Order Info =
1289 += (% data-sider-select-id="a056b4ad-7d05-42b4-ad74-7a3134f8010a" %)15. Order Info(%%) =
904 904  
905 905  
906 906  (% style="color:#0000ff" %)**LPS8v2-XXX-YYY**
... ... @@ -932,7 +932,7 @@
932 932  More info about valid bands, please see [[EC25-E product page>>url:https://www.quectel.com/product/ec25.htm]].
933 933  
934 934  
935 -= 13. Manufacturer Info =
1321 += (% data-sider-select-id="a4433cd3-3bbc-4e6b-8b18-0bd2bc4d6904" %)16. Manufacturer Info(%%) =
936 936  
937 937  
938 938  **Shenzhen Dragino Technology Development co. LTD**
... ... @@ -942,7 +942,7 @@
942 942  LongCheng Street, LongGang District ; Shenzhen 518116,China
943 943  
944 944  
945 -= 14. FCC Warning =
1331 += (% data-sider-select-id="b353afd6-b0f5-48e5-a114-3b5062cbf0d1" %)17. FCC Warning(%%) =
946 946  
947 947  
948 948  (((
Delete Device.docx
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoye
Size
... ... @@ -1,0 +1,1 @@
1 +336.4 KB
Content
image-20231017111606-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +117.6 KB
Content
image-20231017112115-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +114.3 KB
Content
image-20231017114417-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +130.4 KB
Content
image-20231017115124-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +28.6 KB
Content
image-20231017115330-5.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +110.1 KB
Content
image-20231031162854-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +64.9 KB
Content
image-20231031162927-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +35.0 KB
Content
image-20231106175329-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +63.7 KB
Content
image-20231106175457-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +63.7 KB
Content
image-20231106175523-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +64.8 KB
Content
image-20231106180816-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +41.6 KB
Content
image-20231106180846-5.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +41.9 KB
Content
image-20231124113209-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoye
Size
... ... @@ -1,0 +1,1 @@
1 +198.7 KB
Content
image-20231201165904-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoye
Size
... ... @@ -1,0 +1,1 @@
1 +29.5 KB
Content
image-20231201170355-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoye
Size
... ... @@ -1,0 +1,1 @@
1 +70.2 KB
Content
image-20231207144627-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +182.9 KB
Content
image-20231207144758-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +51.0 KB
Content
image-20231207145210-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +104.4 KB
Content
image-20240203172853-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +24.5 KB
Content
image-20240318095605-1.jpeg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Edwin
Size
... ... @@ -1,0 +1,1 @@
1 +37.3 KB
Content
image-20240318095617-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Edwin
Size
... ... @@ -1,0 +1,1 @@
1 +32.9 KB
Content
image-20240318160845-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +36.5 KB
Content
image-20240416112509-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoye
Size
... ... @@ -1,0 +1,1 @@
1 +82.7 KB
Content
image-20240416112618-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoye
Size
... ... @@ -1,0 +1,1 @@
1 +128.5 KB
Content
image-20240416112649-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoye
Size
... ... @@ -1,0 +1,1 @@
1 +119.8 KB
Content
image-20240416112712-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoye
Size
... ... @@ -1,0 +1,1 @@
1 +29.6 KB
Content
image-20240416112948-5.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoye
Size
... ... @@ -1,0 +1,1 @@
1 +29.6 KB
Content
image-20240518145859-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +59.7 KB
Content
image-20240518145929-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +59.5 KB
Content
image-20240518152100-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +39.5 KB
Content
image-20240518152148-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +78.0 KB
Content
image-20240518154223-5.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +71.7 KB
Content
image-20240803095144-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +52.0 KB
Content
image-20240831151427-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +63.2 KB
Content
image-20240831152113-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +62.3 KB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0