Summary

• Page properties (2 modified, 0 added, 0 removed)
• Attachments (0 modified, 0 added, 1 removed)
  • image-20230329162900-1.png

Details

Page properties

Author

...	...	@@ -1,1 +1,1 @@
1		-XWiki.Bei
	1	+XWiki.Xiaoling

Content

...	...	@@ -24,58 +24,43 @@
24	24	== 2.1 Generate software set up for AT Commands via UART ==
25	25
26	26
27		-(% start="1" style="list-style-type:decimal" %)
28	28	1. Use a general serial tool.
29	29	1. Connect PC to device's UART interface
30	30	1. Set up serial tool with : BaudRate: 9600, databit:8, No parity, No flow control.
31		-1. (((
32		-The password is the last six characters of APPSKEY or PIN of box
33	33
34		-Example：
35		-
36		-APPSKEY= 41 85 71 A7 5D 7E 54 52 25 58 74 85 96 14 74 85
37		-
38		-The password：147485
39		-
40		-[[image:image-20230329162900-1.png||height="302" width="648"]]
41		-
42		-
43		-)))
44		-
45	45	[[image:image-20221224170218-1.png||height="497" width="640"]]
46	46
47	47
48	48	== 2.2 UART Connection for SIB mother board ==
49	49
50		-
51	51	[[image:image-20221224171304-3.png||height="545" width="863"]]
52	52
53	53
	39	+
54	54	= 3. UART for Firmware Upgrade =
55	55
56	56	== 3.1 General Instruction for UART update firmware ==
57	57
58		-
59	59	LoRaSTv4 Base hardware support UART update firmware. the UART connection is the same as AT Command connection, with the need for two extra action. See below for the steps:
60	60
61		- (% style="color:blue" %)**Step1**(%%): Set BOOT Switch to (% style="color:blue" %)**PROG**(%%) mode. PROG mode is for update firmware specially.
	46	+ **Step1**: Set BOOT Switch to **PROG** mode. PROG mode is for update firmware specially.
62	62
63		- (% style="color:blue" %)**Step2**(%%): Press (% style="color:blue" %)**Reset**(%%) button, the module will then boot into program mode.
	48	+ **Step2**: Press **Reset** button, the module will then boot into program mode.
64	64
65		- (% style="color:blue" %)**Step3**(%%): Use (% style="color:blue" %)**TremoProgrammer**(%%) to update the firmware to LoRaST v4.
	50	+ **Step3**: Use **TremoProgrammer** to update the firmware to LoRaST v4.
66	66
67		- (% style="color:blue" %)**Step4**(%%): Set BOOT Switch to (% style="color:blue" %)**FLASH**(%%) position. Press Reset button again and module will run the new software.
	52	+ **Step4**: Set BOOT Switch to **FLASH** position. Press Reset button again and module will run the new software.
68	68
69	69
70		-Below is the method for how to update via (% style="color:blue" %)**TremoProgrammer:**
	55	+Below is the method for how to update via **TremoProgrammer:**
71	71
72	72	1.  Software download link:  [[https:~~/~~/www.dropbox.com/sh/j0qyc7a9ejit7jk/AACtx2tK4gEv6YFXMIVUM4dLa?dl=0>>url:https://www.dropbox.com/sh/j0qyc7a9ejit7jk/AACtx2tK4gEv6YFXMIVUM4dLa?dl=0]]
73	73
74		-2.  Run** (% style="color:blue" %)TremoProgrammer.(%%)**
	59	+2.  Run** TremoProgrammer.**
75	75
76		-3.  Choose software and set the address to (% style="color:blue" %)**0x0800D000**
	61	+3.  Choose software and set the address to **0x0800D000**
77	77
78		-4. Rember to set BOOT Switch to (% style="color:blue" %)**FLASH**(%%) after update
	63	+4. Rember to set BOOT Switch to FLASH after update
79	79
80	80	[[image:image-20221224174341-4.png||height="471" width="374"]]
81	81
...	...	@@ -82,10 +82,8 @@
82	82
83	83	== 3.2 UART Connection for SIB mother board for Program. ==
84	84
85		-
86	86	Below shows the SIB board UART connection, reset button and BOOT Switch (Program Jumper) position. They can be used for firmware upgrade reference.
87	87
88	88	[[image:image-20221224174605-6.png||height="569" width="880"]]
89	89
90	90
91		-

image-20230329162900-1.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Bei

Size

...	...	@@ -1,1 +1,0 @@
1		-217.0 KB

Content