Changes for page Remote Access Gateway

Last modified by Kilight Cao on 2022/07/25 10:47

From version < 18.4 >

edited by Xiaoling
on 2022/05/27 11:13

To version < 19.20 >

edited by Xiaoling
on 2022/07/14 14:59

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -1,28 +1,32 @@
--     **Contents:**
++     **Table of Contents:**
  {{toc/}}
--= **1. Use Remote.it service** =
++= **1.  Use Remote.it service** =
++
++
  Remote.it for remote access is available in the latest Dragino firmware for gateway. For security concern, the remote.it only available base on end user demand.
  (% style="color:red" %)**Important Notice:**
--(% style="color:red" %)* **Remote.it access will give full control of your device to remote support.**
--~* **The Remote.it allow Dragino Support to remote access to the device, If user want to access himself, it need to sign up for an remote.it account.**
++* (% style="color:red" %)**Remote.it access will give full control of your device to remote support.**
++* (% style="color:red" %)**The Remote.it allow Dragino Support to remote access to the device, If user want to access himself, it need to sign up for an remote.it account.**
  For how to use remoteit, please see : [[Remoteit user instruction for Dragino Gateway>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/&file=Dragino-Remoteit_User_Manual.pdf]].
--= **2. RSSH Introduction** =
++= **2.  RSSH Introduction** =
++
++
  Reverse SSH for remote access is available in the latest Dragino firmware for gateway. For security concern, the RSSH only available base on end user demand.
  (% style="color:red" %)**Important Notice:**
--(% style="color:red" %)* **RSSH access will give full control of your device to remote support. Please remove sensitivity info before perform this**
--~* **This RSSH allow Dragino Support to remote access to the device, If user want to access himself, he need to set up the RSSH server himself.**
++* (% style="color:red" %)**RSSH access will give full control of your device to remote support. Please remove sensitivity info before perform this**
++* (% style="color:red" %)**This RSSH allow Dragino Support to remote access to the device, If user want to access himself, he need to set up the RSSH server himself.**
  Below gateway support reverse SSH access:
@@ -35,10 +35,14 @@
  * MS14 series if installed with the same firmware.
--== **2.1 For Firmware Version lower than lgw~-~-build-v5.4.1616478814-20210323-1355** ==
--=== **2.1.1 End User Guide to use SSH access** ===
++== **2.1  For Firmware Version lower than lgw~-~-build-v5.4.1616478814-20210323-1355** ==
++
++
++=== **2.1.1  End User Guide to use SSH access** ===
++
++
  Go to this the Reverse SSH page as below:
  [[image:image-20220527102348-1.png]]
@@ -50,11 +50,11 @@
  Connection OK.
--* (% style="color:#4f81bd" %)**Login ID**(%%): Input (% style="color:#4f81bd" %)**sshuser**
--* (% style="color:#4f81bd" %)**Host Address**(%%): Input** (% style="color:#4f81bd" %)support.dragino.com(%%)**
--* (% style="color:#4f81bd" %)**Host Port**(%%): Please email to support @ dragino.com to get a valid host port.
++* (% style="color:#4f81bd" %)**Login ID**(%%):                    Input (% style="color:#4f81bd" %)**sshuser**
++* (% style="color:#4f81bd" %)**Host Address**(%%):           Input** (% style="color:#4f81bd" %)support.dragino.com(%%)**
++* (% style="color:#4f81bd" %)**Host Port**(%%):                  Please email to support @ dragino.com to get a valid host port.
  * (% style="color:#4f81bd" %)**Connect at Startupt**(%%): Choose to enable connect once device is powered.
--* (% style="color:#4f81bd" %)**Network Keys:**(%%)Click the Generate keys to generate the keys and download / mail it to Dragino support so Dragino can prepare the remote access to
++* (% style="color:#4f81bd" %)**Network Keys:          **(%%)Click the Generate keys to generate the keys and download / mail it to Dragino support so Dragino can prepare the remote access to
  (((
  After doing above, please download and mail the public keys to Dragino support and wait for our mail for the valid host port. Input the valid host port got from our support and click connect so we can remote access to your gateway.
@@ -61,8 +61,10 @@
  )))
--=== 2.1.2 How to Ser up a Reverse SSH access ===
++=== **2.1.2  How to Ser up a Reverse SSH access** ===
++
++
  Advance administrator can config a SSH server to provide support their end user themselves. Instruction is as below:
 . Prepare a Linux server with public IP. The gateways need to be able to create SSH connection to this server. We recommend to use a server that performs no other function than to support the RSSH access, and to have no additional accounts active, and no access from the Internet that uses ID/password authentication.
@@ -81,8 +81,9 @@
  )))
--==== 2.1.2.1 Note for set up RSSH server ====
++==== **2.1.2.1  Note for set up RSSH server** ====
++
  If gateway reboot or the connection is incidentely close by end node. The port in SSH server will still be occupy for a long time. Administrator can use below commands to release the port.
  (% class="box" %)
@@ -96,7 +96,7 @@
  )))
--== 2.2 For Firmware Version higher than lgw~-~-build-v5.4.1618196981-20210412-1111 ==
++== **2.2  For Firmware Version higher than lgw~-~-build-v5.4.1618196981-20210412-1111** ==
  Below gateway support reverse SSH access:
@@ -111,20 +111,23 @@
  )))
--=== 2.2.1 End User Guide to use SSH access ===
++=== **2.2.1  End User Guide to use SSH access** ===
--==== 2.2.1.1 Install the SSH service for server ====
--===== 2.2.1.1.1 Step 1:Download the SSH service code =====
++==== **2.2.1.1  Install the SSH service for server** ====
--1).git clone [[https:~~/~~/github.com/dragino/rssh-server.git>>url:https://github.com/dragino/rssh-server.git]] rssh-server
++===== (% style="color:blue" %)**Step 1 : Download the SSH service code**(%%) =====
++
++
++**1).  **git clone [[https:~~/~~/github.com/dragino/rssh-server.git>>url:https://github.com/dragino/rssh-server.git]] rssh-server
++
  [[image:image-20220527105447-1.png]]
  git clone rssh-server
--2).cd rssh-server; sudo make ~-~--> to Generate the execute file：rssh_serv
++**2). ** cd rssh-server; sudo make ~-~--> to Generate the execute file：rssh_serv
  [[image:image-20220527105511-2.png]]
@@ -160,24 +160,30 @@
  lack of sqlite3
--How to install Sqlit3
++(% style="color:blue" %)**How to install Sqlit3:**
  (% class="box" %)
  (((
--Step1: Download the SQLit3 installation package
++(% style="color:#037691" %)**Step1:**(%%) Download the SQLit3 installation package
             sudo wget [[https:~~/~~/www.sqlite.org/2021/sqlite-autoconf-3350400.tar.gz>>url:https://www.sqlite.org/2021/sqlite-autoconf-3350400.tar.gz]]
--Step2: tar the SQLit3 installation package
++
++(% style="color:#037691" %)**Step2:**(%%) tar the SQLit3 installation package
             sudo tar -zxvf sqlite-autoconf-3350300.tar.gz
--Step3: Generate the makefile
++
++(% style="color:#037691" %)**Step3:**(%%) Generate the makefile
             cd sqlite-autoconf-3350300/;./configure
--Step4: Compile makefile
++
++(% style="color:#037691" %)**Step4:**(%%) Compile makefile
             sudo make
--Step5: Install makefile
++
++(% style="color:#037691" %)**Step5: **(%%)Install makefile
             sudo make install
--Check:
--           cd /usr/local/bin;ls -al                             ~-~->    Check to see if there is a file for sqlite3
--           cd sqlite-autoconf-3350300/;./sqlite3 test.db        ~-~->    Test whether the sqlite3 was installed successfully
--debug:
++
++(% style="color:#037691" %)**Check:**(%%)
++           cd /usr/local/bin;ls -al                                             ~-~->    Check to see if there is a file for sqlite3
++           cd sqlite-autoconf-3350300/;./sqlite3 test.db        ~-~->     Test whether the sqlite3 was installed successfully
++
++(% style="color:#037691" %)**debug:**(%%)
            If you get the imformation that is SQLite header and source version mismatch, when you execute./sqlite3 test.db.
            Please execute the command /sbin/ldconfig.
            After that execute the command ./sqlite3 test.db again.
@@ -184,17 +184,19 @@
  )))
--===== 2.2.1.1.2 Step 2 :Install and run the RSS service =====
--1): intall database for /var/rsshdb.sqlite3 and Server development port for 3721(The default is 3721)
++===== (% style="color:blue" %)**Step 2 : Install and run the RSS service**(%%) =====
++
++**1):**  intall database for /var/rsshdb.sqlite3 and Server development port for 3721(The default is 3721)
++
  user must enter the root account and run the following commands
  (% class="box" %)
  (((
--  $ ./create_sqlite3_db.sh
++**~  $ ./create_sqlite3_db.sh
    $ ./rssh_serv -p  3721 2>&1 &
--  $ ps -ef | grep rssh_serv check 3721 port
++  $ ps -ef | grep rssh_serv check 3721 port**
  )))
  [[image:image-20220527110436-6.png]]
@@ -201,12 +201,13 @@
  intall database and server development port
++
  **Debug:**
  (% class="box" %)
  (((
--Check /var/rsshdb.sqlite3 ~-~->(% style="color:#4f81bd" %)** ls /var/rsshdb.sqlite3**(%%)
--Check ls /var/rsshdb.sqlite3 ~-~-> (% style="color:#4f81bd" %)**sudo chmod 777 rssh_serv**
++**Check /var/rsshdb.sqlite3     ~-~->(% style="color:#4f81bd" %)   ls /var/rsshdb.sqlite3(%%)**
++**Check ls /var/rsshdb.sqlite3 ~-~->**   (% style="color:#4f81bd" %)**sudo chmod 777 rssh_serv**
  )))
  (% class="box" %)
@@ -216,8 +216,10 @@
  )))
--===== 2.2.1.1.3 Step 3 :Create a minimal SSH user (reverse SSH proxy for the gateway) =====
++===== (% style="color:blue" %)**Step 3 : Create a minimal SSH user (reverse SSH proxy for the gateway)**(%%) =====
++
++
  **1): (% style="color:#4f81bd" %)sudo useradd XXXXX(%%)** (custom user name)
  **2):** (% style="color:#4f81bd" %)**sudo passwd xxxxxx**
@@ -224,28 +224,34 @@
  **3):** (% style="color:#4f81bd" %)**cp /bin/bash /bin/rbash**
--**4):** (% style="color:#4f81bd" %)**sudo nano /etc/passwd**(%%) ~-~-> Change /bin/bash to /bin/rbash
++**4):** (% style="color:#4f81bd" %)**sudo nano /etc/passwd**(%%)   ~-~-> Change /bin/bash to /bin/rbash
  **5):** (% style="color:#4f81bd" %)**sudo nano /home/xxxxx/.bashrc**(%%) **empty it,and input export PATH=$HOME/bin**
  **6):** (% style="color:#4f81bd" %)**sudo nano /home/xxxxx/.bash_profile**(%%) **empty it,and input export PATH=$HOME/bin**
--**Now user "XXXXX" is the user with limited permissions of the current system**
++(% style="color:red" %)**Now user "XXXXX" is the user with limited permissions of the current system**
--=== 2.2.2 How does user get the gateway to connect to a user's private server ===
--===== 2.2.2.1 Step1: Come bace the gateway web UI for get the gateway Public key =====
--1) in the system ~-~-> (% style="color:#4f81bd" %)**Remote Mgmt/span>**
++=== **2.2.2  How does user get the gateway to connect to a user's private server** ===
++
++===== (% style="color:blue" %)**Step 1 : Come bace the gateway web UI for get the gateway Public key**(%%) =====
++
++
++**1) **in the system ~-~-> (% style="color:#4f81bd" %)**Remote Mgmt**
++
  [[image:image-20220527110531-7.png]]
  Remote Mgmt
--===== **2.2.2.2 Step2: Authorization server** =====
++===== (% style="color:blue" %)**Step 2 : Authorization server**(%%) =====
++
++
  copy the Gateway Publickey into user's private server "/home/XXXXX/.ssh/authorized_keys" file.
  [[image:image-20220527110625-8.png]]
@@ -253,8 +253,10 @@
  Publickey
--===== **2.2.2.3 Step3: connecte private server** =====
++===== (% style="color:blue" %)**Step 3 : connecte private server**(%%) =====
++
++
  in the gateway web UI
  [[image:image-20220527110700-9.png]]
@@ -261,19 +261,22 @@
  gateway web UI
++
  (% class="box" %)
  (((
--(% style="color:#4f81bd" %)**Connection Type **(%%)     : If user's least privileged user with private server uses a password, select (% style="color:#4f81bd" %)**Public Key**(%%)
--**Note:if user's least privileged user no uses a password,choose from both is fine**
--(% style="color:#4f81bd" %)**Login ID**(%%)             : Input user name "eg : "XXXXX"
--(% style="color:#4f81bd" %)**Host Address**(%%)         : Input user's private server address
--(% style="color:#4f81bd" %)**Connect at Startupt**(%%): Choose to enable connect once device is powered.
++(% style="color:#4f81bd" %)**Connection Type **(%%) :       If user's least privileged user with private server uses a password, select (% style="color:#4f81bd" %)**Public Key**(%%)
++(% style="color:red" %)**Note: if user's least privileged user no uses a password,choose from both is fine**(%%)
++(% style="color:#4f81bd" %)**Login ID**(%%) :                      Input user name "eg : "XXXXX"
++(% style="color:#4f81bd" %)**Host Address**(%%)  :            Input user's private server address
++(% style="color:#4f81bd" %)**Connect at Startupt**(%%):   Choose to enable connect once device is powered.
  Click Save and then Connect
  )))
--===== **2.2.2.4 Step 4 :Cheak is fine** =====
++===== (% style="color:blue" %)**Step 4 : Cheak is fine**(%%) =====
++
++
  Rssh Host connection Ok
  [[image:image-20220527111009-10.png]]
@@ -288,32 +288,38 @@
  Check the gateway
--===== **2.2.2.5 Step5:Create an authorization key file** =====
--1):sudo mkdir /home/xxxxx/.ssh; sudo touch /home/xxxxx/.ssh/authorizedkey
++===== (% style="color:blue" %)**Step 5 : Create an authorization key file**(%%) =====
++
++**1):**  sudo mkdir /home/xxxxx/.ssh; sudo touch /home/xxxxx/.ssh/authorizedkey
++
  **Debug:**
  (% class="box" %)
  (((
-- check: sudo ls /home/xxxxx/.ssh/authorizedkey
++**~ check: sudo ls /home/xxxxx/.ssh/authorizedkey**
  )))
--=== **2.2.3 How to Ser up a Reverse SSH access** ===
++=== **2.2.3  How to Ser up a Reverse SSH access** ===
--==== **2.2.3.1 Step1: Log into the server system** ====
++==== (% style="color:blue" %)**Step 1 : Log into the server system**(%%) ====
++
++
  [[image:image-20220527111145-12.png]]
  Loging server
--==== **2.2.3.2 Step2:access the gateway** ====
++==== (% style="color:blue" %)**Step 2 : access the gateway**(%%) ====
++
++
  (% class="box" %)
  (((
--$ cd rssh-server/
++**$ cd rssh-server/**
  )))
  Check the gateway linking to the server $ ./connect-gw.sh -l
@@ -323,8 +323,11 @@
  Check the gateway linking to the server
++
  access the gateway $ ./connect-gw.sh <GWID>
  [[image:image-20220527111300-14.png]]
  reverse ssh access the gateway
++
++

Changes for page Remote Access Gateway

Summary

Details

Applications

Navigation