Wiki source code of Notes for LORIOT
Hide last authors
author | version | line-number | content |
---|---|---|---|
![]() |
1.4 | 1 | (% class="wikigeneratedid" %) |
![]() |
1.6 | 2 | **~ Contents:** |
![]() |
1.1 | 3 | |
![]() |
1.6 | 4 | {{toc/}} |
![]() |
1.4 | 5 | |
![]() |
48.4 | 6 | |
7 | |||
8 | |||
![]() |
1.4 | 9 | = 1. Introduction = |
10 | |||
11 | ((( | ||
![]() |
1.7 | 12 | ((( |
![]() |
1.2 | 13 | The Dragino LoRaWAN gateway can commuicate with [[LORIOT>>url:https://www.loriot.io/]] LoRaWAN Network Server: |
![]() |
1.4 | 14 | ))) |
![]() |
1.7 | 15 | ))) |
![]() |
1.1 | 16 | |
![]() |
1.4 | 17 | ((( |
![]() |
1.7 | 18 | ((( |
![]() |
1.2 | 19 | Below list the support products and Requirements: |
![]() |
1.4 | 20 | ))) |
![]() |
1.7 | 21 | ))) |
![]() |
1.1 | 22 | |
![]() |
1.4 | 23 | 1. ((( |
![]() |
1.7 | 24 | ((( |
![]() |
1.4 | 25 | LoRaWAN Gateway model: [[LPS8>>url:http://www.dragino.com/products/lora-lorawan-gateway/item/148-lps8.html]], [[LG308>>url:http://www.dragino.com/products/lora-lorawan-gateway/item/140-lg308.html]], [[DLOS8>>url:http://www.dragino.com/products/lora-lorawan-gateway/item/160-dlos8.html]] |
26 | ))) | ||
![]() |
1.7 | 27 | ))) |
![]() |
1.4 | 28 | 1. ((( |
![]() |
1.7 | 29 | ((( |
![]() |
1.4 | 30 | Firmware version since :[[LG02_LG08~~-~~-build-v5.4.1590459021-20200526-1012>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Release/]] |
![]() |
32.2 | 31 | |
32 | |||
![]() |
1.4 | 33 | ))) |
![]() |
1.7 | 34 | ))) |
![]() |
1.1 | 35 | |
![]() |
1.4 | 36 | = 2. Gateway Setup Instruction = |
![]() |
1.1 | 37 | |
![]() |
1.4 | 38 | == 2.1 Step 1: Get Gateway ETH0 MAC Address == |
![]() |
1.1 | 39 | |
![]() |
1.4 | 40 | ((( |
![]() |
1.2 | 41 | Dragino LoRaWAn gateway use ETH0 MAC address to generate Gateway ID to communicate with LORIOT, User can get the ETH0 MAC address from SSH access and run **ifconfig** command. |
![]() |
1.4 | 42 | ))) |
![]() |
1.1 | 43 | |
![]() |
4.2 | 44 | [[image:image-20220524175559-2.png]] |
![]() |
1.1 | 45 | |
![]() |
1.2 | 46 | Get ETH0 MAC address |
![]() |
1.1 | 47 | |
![]() |
1.4 | 48 | ((( |
49 | **Note**: To make set up more friendly, the ETH0 will show on the LORIOT page in a new firmware version. | ||
![]() |
32.2 | 50 | |
51 | |||
![]() |
1.4 | 52 | ))) |
![]() |
1.1 | 53 | |
![]() |
1.5 | 54 | == 2.2 Step 2: Choose LORIOT service == |
![]() |
1.1 | 55 | |
56 | |||
![]() |
1.2 | 57 | Choose to use LORIOT as LoRaWAN service provider |
![]() |
1.1 | 58 | |
![]() |
7.2 | 59 | [[image:image-20220524175646-4.png]] |
![]() |
1.1 | 60 | |
![]() |
1.2 | 61 | Install and choose the LORIOT server to be used |
62 | |||
![]() |
32.2 | 63 | |
![]() |
1.5 | 64 | == 2.3 Step 3: Checking Connection Status == |
![]() |
1.2 | 65 | |
![]() |
7.2 | 66 | [[image:image-20220524175703-5.png]] |
![]() |
1.2 | 67 | |
68 | Click to Home page and check the connection status | ||
69 | |||
![]() |
32.2 | 70 | |
![]() |
1.5 | 71 | == 2.4 Step 4: Setup Account in LORIOT == |
![]() |
1.2 | 72 | |
73 | Login [[LORIOT>>url:https://www.loriot.io/]] and create account | ||
74 | |||
![]() |
9.2 | 75 | [[image:image-20220524175722-6.png]] |
![]() |
1.2 | 76 | |
77 | Log in LORIOT portal | ||
78 | |||
79 | |||
![]() |
1.4 | 80 | Choose to use the server same as the gateway setting |
81 | |||
![]() |
32.2 | 82 | [[image:image-20220526111312-1.png||height="493" width="1098"]] |
![]() |
1.2 | 83 | |
84 | Choose server | ||
85 | |||
86 | |||
![]() |
1.4 | 87 | Create a New Network |
88 | |||
![]() |
32.2 | 89 | [[image:image-20220526111425-2.png||height="579" width="1378"]] |
![]() |
1.2 | 90 | |
91 | Create a New Network | ||
92 | |||
93 | |||
![]() |
32.2 | 94 | [[image:image-20220526111500-3.png]] |
![]() |
1.5 | 95 | |
![]() |
1.2 | 96 | Create a New Network |
97 | |||
![]() |
32.2 | 98 | |
![]() |
1.5 | 99 | == 2.5 Step 5: Register the gateway == |
![]() |
1.2 | 100 | |
![]() |
32.2 | 101 | [[image:image-20220526111650-4.png]] |
![]() |
1.2 | 102 | |
103 | Register the Gateway in LORIOT | ||
104 | |||
105 | |||
106 | Choose LG308 as gateway model | ||
107 | |||
![]() |
32.2 | 108 | [[image:image-20220526111742-5.png||height="496" width="1372"]] |
![]() |
1.2 | 109 | |
110 | Choose LG308 as gateway model | ||
111 | |||
112 | |||
113 | Input Gateway ETH0 address | ||
114 | |||
![]() |
35.2 | 115 | [[image:image-20220526111918-6.png||height="744" width="1336"]] |
![]() |
1.2 | 116 | |
117 | Choose SX1301 Reference and use SPI protocol | ||
118 | |||
119 | |||
120 | Choose the right Frequency Band and input location | ||
121 | |||
![]() |
35.2 | 122 | [[image:image-20220526112029-7.png||height="620" width="1306"]] |
![]() |
1.2 | 123 | |
124 | Set up regional settings. | ||
125 | |||
![]() |
45.2 | 126 | |
![]() |
1.5 | 127 | == 2.6 Step 6: Check Connection == |
![]() |
1.2 | 128 | |
![]() |
1.5 | 129 | ((( |
![]() |
1.2 | 130 | LORIOT will show disconnect if Gateway doesn't connect |
![]() |
1.5 | 131 | ))) |
![]() |
1.2 | 132 | |
![]() |
1.5 | 133 | ((( |
![]() |
1.2 | 134 | LORIOT will show connect if Gateway connect to LORIOT ok. |
![]() |
1.5 | 135 | ))) |
![]() |
1.2 | 136 | |
![]() |
36.2 | 137 | [[image:image-20220526112143-8.png||height="654" width="1373"]] |
![]() |
1.2 | 138 | |
139 | Status: Connected | ||
140 | |||
![]() |
45.2 | 141 | |
![]() |
1.5 | 142 | == 2.7 Debug If there is connection issue == |
![]() |
1.2 | 143 | |
144 | User can check if loriot is running by checking the web ui | ||
145 | |||
![]() |
45.2 | 146 | [[image:image-20220526112917-18.png]] |
![]() |
1.2 | 147 | |
148 | Status: Connected | ||
149 | |||
![]() |
1.11 | 150 | ((( |
![]() |
1.2 | 151 | If user want to see more log, he can run below commands in Linux and see the full log: |
![]() |
1.11 | 152 | ))) |
![]() |
1.2 | 153 | |
![]() |
1.5 | 154 | (% class="box" %) |
155 | ((( | ||
![]() |
1.8 | 156 | ((( |
![]() |
1.11 | 157 | ps | grep "loriot_dragino" | grep -v grep | awk '{print $1}' | xargs kill -s 9 |
158 | /usr/bin/loriot_dragino_lg308_spi -f -s eu1.loriot.io | ||
![]() |
1.5 | 159 | ))) |
![]() |
1.8 | 160 | ))) |
![]() |
1.2 | 161 | |
![]() |
1.11 | 162 | ((( |
![]() |
1.2 | 163 | Above two commands will first kill the loriot process and run it again to get more output. |
![]() |
1.11 | 164 | ))) |
![]() |
1.2 | 165 | |
![]() |
47.2 | 166 | [[image:image-20220530145011-1.png]] |
![]() |
1.2 | 167 | |
168 | Get more debug info | ||
169 | |||
![]() |
45.2 | 170 | |
![]() |
1.5 | 171 | = 3. End Device Note = |
![]() |
1.2 | 172 | |
![]() |
1.5 | 173 | == 3.1 Downlink Setup == |
![]() |
1.2 | 174 | |
![]() |
48.2 | 175 | [[image:image-20220530145133-2.png]] |
![]() |
1.2 | 176 | |
![]() |
45.2 | 177 | |
![]() |
41.2 | 178 | [[image:image-20220526112416-11.png]] |
![]() |
1.2 | 179 | |
![]() |
45.2 | 180 | |
![]() |
41.2 | 181 | [[image:image-20220526112459-12.png]] |
![]() |
1.2 | 182 | |
![]() |
45.2 | 183 | |
![]() |
41.2 | 184 | [[image:image-20220526112537-13.png]] |
![]() |
1.2 | 185 | |
![]() |
45.2 | 186 | |
![]() |
41.2 | 187 | [[image:image-20220526112608-14.png||height="610" width="1382"]] |
![]() |
1.2 | 188 | |
![]() |
45.2 | 189 | |
![]() |
44.2 | 190 | [[image:image-20220526112655-15.png]] |
![]() |
1.2 | 191 | |
![]() |
45.2 | 192 | |
![]() |
44.2 | 193 | [[image:image-20220526112719-16.png]] |
![]() |
1.2 | 194 | |
![]() |
45.2 | 195 | |
![]() |
44.2 | 196 | [[image:image-20220526112759-17.png||height="483" width="1386"]] |