Changes for page

Last modified by Xiaoling on 2025/06/18 13:51

From 61.1 to 62.1 From 66.1 to 66.2

From version 62.1

edited by Mengting Qiu
on 2025/05/05 19:36

Change comment: Uploaded new attachment "image-20250505193603-10.png", version {1}

To version 66.1

edited by Mengting Qiu
on 2025/05/07 10:09

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -24,7 +24,7 @@
  **Wind Direction:**
  * Range: 0~~3599
--* Accuracy: +3°
++* Accuracy: ±3°
  * Ultrasonic measurement,no start wind strength needed
  * Built-in electronic compass. No need to consider installation direction
@@ -31,12 +31,12 @@
  **Temperature:**
  * Range: -40°C ~~ +80°C
--* Accuracy: +0.5°C
++* Accuracy: ±0.5°C
  **Humidity:**
  * Range: 0 ~~ 99% RH
--* Accuracy Tolerance : Typ +3% RH
++* Accuracy Tolerance : Typ ±3% RH
  **Air Pressure:**
@@ -46,7 +46,7 @@
  **Noise:**
  * Range: 30dB~~120dB
--* Accuracy: +0.5dB
++* Accuracy: ±0.5dB
  **PM2.5:**
@@ -57,13 +57,13 @@
  **PM10:**
  * Range: 0~~1000ug/m3
--* Accuracy: +3%FS
++* Accuracy: ±3%FS
  * Resolution: 1ug/m3
  **llumination:**
  * Range: 0~~200k Lux
--* Accuracy: +7%(25 °C)
++* Accuracy: ±7%(25 °C)
  == 1.2 Wiring ==
@@ -74,12 +74,12 @@
  === 1.2.2 New version wiring ===
--[[image:image-20250505102835-7.png||height="409" width="739"]]
++[[image:image-20250505193603-10.png||height="405" width="762"]]
--
  == 1.3 Mechinical Drawing ==
++
  (% class="lead" %)
  **Device Dimension**
@@ -96,6 +96,7 @@
  == 2.1 Overview and Spec ==
++
  Older versions of interfaces                               New version of the interface
  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/WSC2-LB_LoRaWAN_Weather_Station_User_Manual/WebHome/image-20240707215336-2.png?width=218&height=159&rev=1.1||alt="image-20240707215336-2.png" height="159" width="218"]]                       [[image:image-20250505190822-2.png||height="155" width="197"]]
@@ -113,13 +113,15 @@
  [[image:image-20241127091433-1.jpeg||height="361" width="517"]]
++
  === 2.2.2 New version wiring ===
--[[image:image-20250505101405-5.png||height="381" width="748"]]
++[[image:image-20250505193511-9.png||height="392" width="708"]]
  == 2.3 Mechinical Drawing ==
++
  (% class="lead" %)
  **Device Dimension**
@@ -138,234 +138,350 @@
  [[image:image-20240714164856-4.png||height="250" width="433"]]
++= 3. PAR (Photosynthetically Available Radiation) ~-~-~-~--WSS-27 =
--= 3. WSS-27 Photosynthetically Active Radiation Sensor =
--== 3.1 Overview and Spec ==
++WSS-27 photosynthetically active radiation sensor is mainly used to measure the photosynthetically active radiation of natural light in the wavelength range of 400-700nm.
++WSS-27 use precision optical detectors and has an optical filter of 400-700nm, when natural light is irradiated, a voltage signal proportional to the intensity of the incident radiation is generated, and its luminous flux density is proportional to the cosine of the direct angle of the incident light.
++
++== 3.1 Specification ==
++
  [[image:1746411474621-748.png||height="175" width="224"]]
--* Input Power: 5~~24V DC
--* Measuring range: 0～2500μmol/m2·s
--* Response time: <1S
--* Resolution: 1μmol/m2·s
++* Input Power: DC 5 ~~ 24v
++* Interface: RS485
++* Response Spectrum: 400~~700nm
++* Measure range: 0 ~~ 2500μmol/m2•s
++* Resolution: 1μmol/m2•s
  * Accuracy: ±2%
--* Response spectrum: 400～700nm
--* Output signal: RS485 (standard Modbus-RTU protocol)
--* Stability: change within one year <±2%
--* Working environment: -30℃～75℃
++* Yearly Stability: ≤ ±2%
++* Working Temperature: -30℃ ~~ 75℃
++* Working Humidity: 10 ~~ 90%RH
++* Power Consumption: 3mA @ 12v
  == 3.2 Wiring ==
++[[image:image-20250505193330-8.png||height="393" width="744"]]
--[[image:image-20250505102905-9.png||height="406" width="771"]]
++== 3.3 Dimension ==
--== 3.3 Device Dimension ==
++[[image:https://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/Dragino%20LoRaWAN%20Weather%20Station%20User%20Manual/WebHome/1656057538793-888.png?rev=1.1||alt="1656057538793-888.png"]]
--[[image:1746424326901-763.png]]
++= 4. Total Solar Radiation sensor ~-~- WSS-26 =
++WSS-26 is Total Radiation Sensor can be used to measure the total solar radiation in the spectral range of 0.3 to 3 μm (300 to 3000 nm). If the sensor face is down, the reflected radiation can be measured, and the shading ring can also be used to measure the scattered radiation.
--= 4. WSS-06 Simple Total Radiation Sensor =
++The core device of the radiation sensor is a high-precision photosensitive element, which has good stability and high precision; at the same time, a precision-machined PTTE radiation cover is installed outside the sensing element, which effectively prevents environmental factors from affecting its performance
--== 4.1 Overview and Spec ==
++== 4.1 Feature ==
--[[image:1746423871465-411.png||height="217" width="278"]]
++* RS485 Total Solar Radiation sensor
++* Measure Total Radiation between 0.3 ~~ 3μm(300 ~~ 3000nm)
++* Measure Reflected Radiation if sense area towards ground.
--* (% id="cke_bm_101984S" style="display:none" %) (%%)Input Power: 5~~24V DC
--* Spectral Range: 0.3～3μm (300～3000nm)
--* Measuring Range: 0～2000W/m^^2^^
--* Resolution: 0.1W/m^^2^^
--* Measurement Accuracy: ±3%
--* Output signal: RS485 (standard Modbus-RTU protocol)
--* Temperature Characteristics: ±2% (-10℃～40℃)
--* Response Time: <1s
--* Annual Stability: ≤±2%
--* Cosine Response: ≤7% (When the sun altitude angle is 10°)
--* Azimuth Response Error: ≤5% (When the sun altitude angle is 10°)
--* Working environment: -40℃～70℃
++== 4.2 Specification ==
++* (% id="cke_bm_101984S" style="display:none" %)
++* Input Power: DC 5 ~~ 24v
++* Interface: RS485
++* Detect spectrum: 0.3 ~~ 3μm(300～3000nm)
++* Measure strength range: 0 ~~ 2000W/m2
++* Resolution: 0.1W/m2
++* Accuracy: ±3%
++* Yearly Stability: ≤±2%
++* Cosine response: ≤7% (@ Sun angle 10°)
++* Temperature Effect: ±2% (-10℃ ~~ 40℃)
++* Working Temperature: -40℃ ~~ 70℃
++* Working Humidity: 10 ~~ 90%RH
++* Power Consumption: 4mA @ 12v
++
  == 4.2 Wiring ==
--[[image:image-20250505140615-10.png||height="419" width="791"]]
++[[image:image-20250505193313-7.png||height="391" width="722"]]
  == 4.3 Device Dimension ==
--[[image:1746424326901-763.png]]
++[[image:https://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/Dragino%20LoRaWAN%20Weather%20Station%20User%20Manual/WebHome/1656057348695-898.png?rev=1.1||alt="1656057348695-898.png"]]
++== 4.4 Installation Notice ==
--= 5. WSS-25 Air Temperature and Humidity =
++Do not power on while connect the cables. Double check the wiring before power on.
--== 5.1 Overview and Spec ==
++[[image:https://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/Dragino%20LoRaWAN%20Weather%20Station%20User%20Manual/WebHome/1656057369259-804.png?rev=1.1||alt="1656057369259-804.png"]]
--[[image:1746424465810-974.png||height="325" width="288"]]
++[[image:https://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/Dragino%20LoRaWAN%20Weather%20Station%20User%20Manual/WebHome/1656057377943-564.png?rev=1.1||alt="1656057377943-564.png"]]
--* Supply voltage: 5~~24V DC
--* Temperature Measuring Range: Standard -30~~70℃ or 0~~50℃
--* Humidity Measuring Range: 0～100%RH(Non-condensing state)
--* Accuracy: ±0.2℃ (@25℃); ±3%RH (10%～90%)
--* Repeatability: ±0.1℃; ±0.1%RH
--* Long-term stability: <0.04℃/year; <0.5%RH/year
--* Output signal:RS485 (standard Modbus-RTU protocol)
--* Response time: <1s
--* Working Environment: Temperature: -55℃～120℃; Humidity: ≤95%RH
++= 5. Temperature, Humidity, Illuminance, Pressure ~-~- WSS-25 =
++WSS-25 is a 4 in 1 RS485 sensor which can monitor Temperature, Humidity, Illuminance and Pressure at the same time.
++
++== 5.1 Feature ==
++
++* RS485 Temperature, Humidity, Illuminance, Pressure sensor
++
++== 5.2 Specification ==
++
++
++* Input Power: DC 12 ~~ 24v
++* Interface: RS485
++* Temperature Sensor Spec:
++** Range: -30 ~~ 70℃
++** resolution 0.1℃
++** Accuracy: ±0.5℃
++* Humidity Sensor Spec:
++** Range: 0 ~~ 100% RH
++** resolution 0.1 %RH
++** Accuracy: 3% RH
++* Pressure Sensor Spec:
++** Range: 10 ~~ 1100hPa
++** Resolution: 0.1hPa
++** Accuracy: ±0.1hPa
++* Illuminate sensor:
++** Range: 0~~2/20/200kLux
++** Resolution: 10 Lux
++** Accuracy: ±3%FS
++* Working Temperature: -30℃ ~~ 70℃
++* Working Humidity: 10 ~~ 90%RH
++* Power Consumption: 4mA @ 12v
++
  == 5.2 Wiring ==
--[[image:image-20250505140636-11.png||height="419" width="794"]]
++[[image:image-20250505193252-6.png||height="409" width="765"]]
--== 5.3 Device Dimension ==
++== 5.3 Dimension ==
--[[image:1746425244897-496.png||height="363" width="684"]]
++[[image:https://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/Dragino%20LoRaWAN%20Weather%20Station%20User%20Manual/WebHome/1656057170639-522.png?rev=1.1||alt="1656057170639-522.png"]]
--= 6. WSS-24 Rain and snow sensor =
++= 6. Rain/Snow Detect ~-~- WSS-24 =
--== 6.1 Overview and Spec ==
++WSS-24 is a RS485 rain / snow detect sensor. It can monitor Rain or Snow event.
--[[image:image-20250505140953-12.png||height="293" width="246"]]
++WSS-24 has auto heating feature, this ensures measurement more reliable.
++=== 6.1  Feature ===
--* Supply voltage: 12~~24V DC
--* Measurement parameters: Rain or snow
--* Working temperature: -30～70℃; humidity: 10～90%RH
--* Storage temperature: -40～80℃; humidity: 10～90%RH
--* Output signal: RS485 (standard Modbus-RTU protocol)
--* Stability and response time: <1 second
++* RS485 Rain/Snow detect sensor
++* Surface heating to dry
++* grid electrode uses Electroless Nickel/Immersion Gold design for resist corrosion
--== 6.2 Wiring ==
++=== 6.2  Specification ===
++* Detect if there is rain or snow
++* Input Power: DC 12 ~~ 24v
++* Interface: RS485
++* Working Temperature: -30℃ ~~ 70℃
++* Working Humidity: 10 ~~ 90%RH
++* Power Consumption:
++** No heating: 12mA @ 12v,
++** heating: 94ma @ 12v.
--[[image:image-20250505144810-14.png]]
++== 6.2 Wiring ==
--== 6.3 Device Dimension ==
++[[image:image-20250505193053-5.png]]
++== 6.3 Dimension ==
++
  [[image:image-20250505144906-15.png]]
--== 6.4 Installation Angle Requirements ==
++== 6.4 Installation Notice ==
--During installation, the sensor sensing surface should be kept at a 15-degree angle to the horizontal plane to prevent rain and snow accumulation from affecting sensor measurement.
++Do not power on while connect the cables. Double check the wiring before power on.
--[[image:image-20250505190308-23.png]]
++Install with 15°degree.
++[[image:https://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/Dragino%20LoRaWAN%20Weather%20Station%20User%20Manual/WebHome/1656056873783-780.png?rev=1.1||alt="1656056873783-780.png"]]
--= 7. WSS-23 CO2 Sensor & PM2.5 & PM10 Sensor =
++[[image:https://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/Dragino%20LoRaWAN%20Weather%20Station%20User%20Manual/WebHome/1656056883736-804.png?rev=1.1||alt="1656056883736-804.png"]]
--== 7.1 Overview and Spec ==
++== 6.5 Heating ==
--[[image:1746427977346-600.png||height="261" width="318"]]
++WSS-24 supports auto-heat feature. When the temperature is below the heat start temperature 15℃, WSS-04 starts to heat and stop at stop temperature (default is 25℃).
--* Supply voltage: 7~~24V DC
--* Average current: Peak value ≤200mA; average 85 mA
--* Warm-up time: 3min
--* Response time: <90s
--* Stability: ≤2% F•S
++= 7. CO2/PM2.5/PM10 ~-~- WSS-23 =
--**CO2 Sensor:**
++WSS-23 is a RS485 Air Quality sensor. It can monitor CO2, PM2.5 and PM10 at the same time.
++WSS-23 uses weather proof shield which can make sure the sensors are well protected against UV & radiation.
--* Measurement parameters: Carbon dioxide concentration
--* Measurement range: 0-2000ppm, 0-5000ppm, 0-10000ppm
--* Accuracy: ±3%F•S (25℃)
--* Resolution: 1ppm
--* Output signal: RS485 (standard Modbus-RTU protocol)
--* Working temperature: 0℃～50℃
--* Working humidity: 0～95%RH
++== 7.1 Feature ==
--**PM2.5 & PM10 Sensor**
++* RS485 CO2, PM2.5, PM10 sensor
++* NDIR to measure CO2 with Internal Temperature Compensation
++* Laser Beam Scattering to PM2.5 and PM10
--* Measurement parameters: PM2.5 & PM10 concentration
--* Detection range: 0-1000μg/m3
--* Resolution: 1μg/m3
--* Accuracy: ±3%F•S (25℃)
--* Working temperature: -30℃～50℃
--* Storage temperature: -40℃～60℃
--* Working humidity: 15～80%RH (no condensation)
--* Temperature drift: 0.2%F•S/℃
--* Average current: 50mA@7V; 35mA@12V; 20mA@24V
--* Stability: ≤2%F•S
--* Warm-up time: 3min
--* Response time: <90s
++== 7.2  Specification ==
++* CO2 Range: 0 ~~ 5000ppm, accuracy: ±3%F•S(25℃)
++* CO2 resolution: 1ppm
++* PM2.5/PM10 Range: 0 ~~ 1000μg/m3 , accuracy ±3%F•S(25℃)
++* PM2.5/PM10 resolution: 1μg/m3
++* Input Power: DC 7 ~~ 24v
++* Preheat time: 3min
++* Interface: RS485
++* Working Temperature:
++** CO2: 0℃ ~~ 50℃;
++** PM2.5/PM10: -30 ~~ 50℃
++* Working Humidity:
++** PM2.5/PM10: 15 ~~ 80%RH (no dewing)
++** CO2: 0 ~~ 95%RH
++* Power Consumption: 50mA@ 12v.
++
  == 7.2 Wiring ==
--[[image:image-20250505182902-17.png||height="372" width="698"]]
++[[image:image-20250505193033-4.png||height="376" width="689"]]
  == 7.3 Device Dimension ==
--[[image:1746440854349-915.png||height="312" width="588"]]
++[[image:https://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/Dragino%20LoRaWAN%20Weather%20Station%20User%20Manual/WebHome/1656056708366-230.png?rev=1.1||alt="1656056708366-230.png"]]
++== 7.4 Installation Notice ==
++Do not power on while connect the cables. Double check the wiring before power on.
--= 8. WSS-22 Integrated wind speed and direction sensor =
++[[image:https://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/Dragino%20LoRaWAN%20Weather%20Station%20User%20Manual/WebHome/1656056751153-304.png?rev=1.1||alt="1656056751153-304.png"]]
--== 8.1 Overview and Spec ==
++[[image:https://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/Dragino%20LoRaWAN%20Weather%20Station%20User%20Manual/WebHome/1656056766224-773.png?rev=1.1||alt="1656056766224-773.png"]]
++
++= 8. WSS-22 Integrated wind speed and direction sensor =
++
  [[image:1746441120854-584.png||height="271" width="394"]]
--* Supply voltage: 5~~24V DC
--* Wind speed measurement range: 0～30m/s; 0～50m/s; 0～60m/s;
--* Wind direction measurement range: 0～360°
--* Starting wind speed: ≤0.3m/s
--* Accuracy: ±(0.3+0.03V) m/s, ±1°
--* Output signal: RS485 (standard Modbus-RTU protocol)
--* Working environment: Temperature: -30℃～70℃; Humidity: ≤100%RH
--* Storage environment: Temperature: -30℃～70℃; Humidity: ≤100%RH
++WSS-22 is a RS485 wind speed and wind direction monitor designed for weather station solution.
++WSS-22 shell is made of polycarbonate composite material, which has good anti-corrosion and anti-corrosion characteristics, and ensure the long-term use of the sensor without rust. At the same time, it cooperates with the internal smooth bearing system to ensure the stability of information collection
++
++
++== 8.1 Feature ==
++
++* RS485 wind speed / direction sensor
++* PC enclosure, resist corrosion
++
++== 8.2 Specification ==
++
++* Wind speed range: 0 ~~ 60m/s
++* Wind direction range: 0 ~~ 360°
++* Start wind speed: ≤0.3 m/s
++* Accuracy: ±(0.3＋0.03V) m/s , ±1°
++* Input Power: DC 5 ~~ 24v
++* Interface: RS485
++* Working Temperature: -30℃ ~~ 70℃
++* Working Humidity: <100% (no dewing)
++* Power Consumption: 13mA ~~ 12v.
++* Cable Length: 2 meters
++
  == 8.2 Wiring ==
--[[image:image-20250505183552-18.png||height="288" width="550"]]
++[[image:image-20250505192929-2.png||height="314" width="590"]]
  == 8.3 Device Dimension ==
--[[image:1746441469178-155.png||height="372" width="405"]]
++(% class="wikigeneratedid" %)
++[[image:https://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/Dragino%20LoRaWAN%20Weather%20Station%20User%20Manual/WebHome/image-20220624152813-2.png?rev=1.1||alt="image-20220624152813-2.png"]]
--[[image:1746441481289-965.png||height="370" width="404"]]
++== 8.4 Angle Mapping ==
++[[image:https://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/Dragino%20LoRaWAN%20Weather%20Station%20User%20Manual/WebHome/1656056303845-585.png?rev=1.1||alt="1656056303845-585.png"]]
--== 8.4 Installation method ==
--**The integrated wind speed and direction sensor (the outlet is pointing south, the opposite direction is north), the installation method is as follows:**
++== 8.4 Installation Notice ==
++
++Do not power on while connect the cables. Double check the wiring before power on.
++
++The sensor must be installed with below direction, towards North.
++
  [[image:1746441560175-162.png||height="304" width="484"]]
++= 9. Rain Gauge ~-~- WSS-21 =
--= 9. WSS-21 Rain Sensor =
++WSS-21 RS485 Rain Gauge is used in meteorology and hydrology to gather and measure the amount of liquid precipitation (mainly rainfall) over an area.
--== 9.1 Overview and Spec ==
++WSS-21 uses a tipping bucket to detect rainfall. The tipping bucket use 3D streamline shape to make sure it works smoothly and is easy to clean.
--[[image:image-20250505184214-19.png||height="324" width="320"]]
++The tipping bucket of WSS-01 is adjusted to the best angle. When installation, user only needs to screw up and adjust the bottom horizontally.
++WSS-21 package includes screw which can be installed to ground. If user want to install WSS-21 on pole, they can purchase WS-K2 bracket kit.
--* Rain-receiving port size: Φ200mm; sharp angle of blade: 40°～45°
--* Range: 0～100mm (range is limited to analog signal, RS485 signal is not measured)
++== 9.1 Feature ==
++
++* RS485 Rain Gauge
++* Small dimension, easy to install
++* Vents under funnel, avoid leaf or other things to avoid rain flow.
++* ABS enclosure.
++* Horizontal adjustable.
++
++== 9.2  Specification ==
++
  * Resolution: 0.2mm
--* Rain intensity range: 0mm～4mm/min (maximum rain intensity allowed is 8mm/min)
--* Accuracy: ≤±3%
--* Output signal: RS485 (standard Modbus-RTU protocol)
--* Power supply voltage: 5～24V DC
--* Operating temperature: 0℃～70℃ (optional heating function, can be as low as -40℃)
--* Operating humidity: <100% (no condensation)
++* Accuracy: ±3%
++* Range: 0 ~~ 100mm
++* Rainfall strength: 0mm ~~ 4mm/min (max 8mm/min)
++* Input Power: DC 5 ~~ 24v
++* Interface: RS485
++* Working Temperature: 0℃ ~~ 70℃ (incorrect below 0 degree, because water become ICE)
++* Working Humidity: <100% (no dewing)
++* Power Consumption: 4mA @ 12v.
--== 9.2 Wiring ==
++== 9.3 Wiring ==
--[[image:image-20250505184559-21.png||height="335" width="631"]]
++[[image:image-20250505192952-3.png||height="305" width="581"]]
--== 9.3 Device Dimension ==
++== 9.3 Dimension ==
  [[image:image-20250505184528-20.png||height="468" width="471"]]
  [[image:image-20250505185334-22.png||height="533" width="470"]]
++
++== 9.4  Installation Notice ==
++
++
++(((
++Do not power on while connect the cables. Double check the wiring before power on.
++)))
++
++(((
++Installation Photo as reference:
++)))
++
++
++(((
++(% style="color:#4472c4" %)** Install on Ground:**
++)))
++
++(((
++WSS-21 Rain Gauge include screws so can install in ground directly .
++)))
++
++
++(((
++(% style="color:#4472c4" %)** Install on pole:**
++)))
++
++(((
++If user want to install on pole, they can purchase the (% style="color:#4472c4" %)** WS-K2 :  Bracket Kit for Pole installation**(%%), and install as below:
++
++[[image:https://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/Dragino%20LoRaWAN%20Weather%20Station%20User%20Manual/WebHome/image-20220624152218-1.png?width=276&height=526&rev=1.1||alt="image-20220624152218-1.png"]]
++
++WS-K2: Bracket Kit for Pole installation
++
++WSSC-K2 dimension document, please see:
++)))
++
++[[https:~~/~~/www.dropbox.com/sh/7wa2elfm2q8xq4l/AAB7ZB_gSVGrhmJEgU2LyTQNa?dl=0>>https://www.dropbox.com/sh/7wa2elfm2q8xq4l/AAB7ZB_gSVGrhmJEgU2LyTQNa?dl=0]]

Changes for page

Summary

Details

Applications

Navigation