AI Image Sensor Calibration

1

**Table of Contents:**

2

= 1. Overview =

AIS is a video photo recognition sensor, the sensor can be used in electricity meters, gas meters, water meters, pressure gauges and other types of meters. Accurately identify the number of the current dial or upload the picture of the current dial for comparison, which can replace people to go to the door to read the meter, and is more accurate and energy-saving than the meter. The first thing to do is to fix the AIS sensor, the end direction needs to be aligned with the object that needs to be identified, you can check whether the object all appears in the lens range through the upper computer, and then calibrate, Chapter 2 will explain the calibration method of different tables.

17

18

19

= 2. Calibrate Digits Readings =

20

21

22

The factory default firmware of AIS Sensor is a digital wheel dial. It is recommended that the distance between the camera and the digital wheel dial be 3cm-7cm when installing AIS Sensor. Because the distance is too far, the camera's flash will not be able to illuminate the digital wheel dial to obtain readings.

23

24

If you are using a [[pointer type dial>>http://wiki.dragino.com/xwiki/bin/view/Main/AI%20Image%20Sensor%20Calibration/#H2.5PressurePointerMeterCalibration]], just adjust the camera to fully see the entire dial.

25

26

According to the requirements to upgrade the firmware to correct the reading, respectively:[[Digital wheel dial firmware>>https://www.dropbox.com/scl/fo/hqo83crt58fmg80l3a4nn/ABvtOvlHUh6Et-63vjq1HEI?rlkey=vj5s82623blj6okvzfreqlbb5&st=mvgoqzs5&dl=0]]，[[Pointer dial firmware>>https://www.dropbox.com/scl/fi/y03feisk7ztq1ey6pmhqb/Pointer-dial-firmware.rar?rlkey=knlx67m1g26xukrthcum1kk23&st=37ofkd06&dl=0 ]].

27

28

Firmware upgrade Reference:[[Update Firmware for the AI Sensors>>http://wiki.dragino.com/xwiki/bin/view/Main/Update%20Firmware%20for%20AI%20Sensor/]].

29

30

31

== 2.1 Calibrate a Water Meter ==

32

33

=== 2.1.1 Introduce ===

34

35

36

This water meter is designed in accordance with the Chinese standard for drinking cold water meters and hot water meters, GB/T 778.1-2007. It features five dial numbers for measurement accuracy.

37

38

39

=== 2.1.2 Fix Sensor to a Water Meter ===

40

41

42

The assembly necessitates the use of two screws, two spacers, and this specific device.

43

44

Additionally, there are AIS Sensors available along with AUC USB TTL adapters for AIS Sensors.

45

46

The fixture below is just a demo, user might adjust it with their water meter. Here is the STEP file for the fixture as below: [[Water Meter Fixture Demo>>https://www.dropbox.com/scl/fo/p1ykgysrv8p454swsh4zj/AHCYr5pcOM0WNad4fT1sf_I?rlkey=dhm5wem4lgz5nhzmte7egrb0k&e=1&st=0cyy2w2o&dl=0]].

47

48

[[image:image-20240428163842-3.png||height="425" width="609"]] [[image:image-20240428155254-1.png||height="424" width="358"]]

49

50

The procedure is as follows:

51

52

~1. Secure back of the AIS sensor onto the small board and adjust its position according to your requirements. You may use two additional screws for fixation or utilize 3M double-sided adhesive for attachment.

53

54

[[image:image-20240428165320-4.gif]]

55

56

57

2. Proceed by fastening the device using the previously prepared screws and gaskets.

58

59

[[image:image-20240428165354-5.gif]]

60

61

62

3. Finally, nestle the device onto your water meter, ensuring that it can be adjusted to meet your specific needs while guaranteeing that the camera is directed towards the digital wheel face.

63

64

[[image:image-20240428165412-6.gif]].

65

66

67

The AI Sensors and AUC USB TTL Adapter for AIS Sensors are connected and then connected to the PC.

68

69

[[image:image-20240428165634-7.gif]][[image:image-20240428165645-8.jpeg||height="332" width="443"]]

70

71

72

=== 2.1.3 Calibration ===

73

74

75

Open the software [[HMX_FT4222H_GUI.exe>>https://www.dropbox.com/scl/fi/yktibns4o33oh0lqitqjl/HIMAX_AMR_PC_Tool.7z?rlkey=94d637ntx152idhw8vij39icv&st=4lsq8xf9&dl=0]]. Please ensure that the firmware upgrade software ota.exe is closed before opening HMX_FT4222H_GUI.exe.

76

77

For example, Select the corresponding serial port number, here 14.

78

79

(% class="box warningmessage" %)

80

(((

81

(% class="mark" %)Note: before you start the software (%%)HMX_FT4222H_GUI.exe(% class="mark" %). you must pre-install the [[visualcppredist_aio_x6_x64_v42.exe>>https://www.dropbox.com/scl/fi/mzqx6ld5a4zkcecntqjjg/VisualCppRedist_AIO_x86_x64_v42.rar?rlkey=9fuzodmed1fg9ulquh22h0dtr&st=ph6ozi4d&dl=0]] configuration environment. Otherwise, an error pop-up window occurs when running software.

82

)))

83

84

(% aria-label="1713519971789-213.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:1713519971789-213.png||data-widget="image"]]

85

86

(% title="Click and drag to resize" %)

87

88

Next, select a Baud rate of **921600** and click on **"start"**. Then, click on **"show full image" **to display the camera screen.

89

90

(% aria-label="image-20240419174908-5.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:image-20240419174908-5.png||data-widget="image" height="491" width="406"]](% style="background-image:url(http://wiki.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% title="Click and drag to resize" %)(% aria-label="image-20240419175103-7.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:image-20240419175103-7.png||data-widget="image" height="489" width="632"]]

91

92

(% title="Click and drag to resize" %)

93

94

Click **"enable Raw" **and save the BMP image in the "Save" folder. This step is necessary to obtain the coordinate points of the watch face.

95

96

(% aria-label="image-20240419175324-8.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:image-20240419175324-8.png||data-widget="image" height="637" width="911"]](% title="Click and drag to resize" %)

97

98

(% aria-label="image-20240419175324-9.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:image-20240419175324-9.png||data-widget="image" height="348" width="913"]](% title="Click and drag to resize" %)

99

100

This water meter has only five fields, and the coordinates of the digital roulette wheel are shown in the figure.

101

102

If your device's digital scroll wheel dial does not match these five fields, you can try the other field dial coordinate dot plots in 2.4.

103

104

(% aria-label="1713573839396-314.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:1713573839396-314.png||data-widget="image" height="198" width="649"]](% title="Click and drag to resize" %)

105

106

The computer's drawing tool can be used to open the latest bmp image and get the coordinates of the digital wheel dial, as shown below. Based on the format of the digital wheel dial, we can obtain each coordinate point of the current use dial. The (x,y) coordinate on the image is located at the bottom left corner.

107

108

(% aria-label="1713574859715-722.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:1713574859715-722.png||data-widget="image" height="481" width="576"]]

109

110

(% title="Click and drag to resize" %)

111

112

Click the "ROI setting" button in "HIMAX_AMR_PC_Tool" and three options will pop up

113

114

The "Long dial" option is the long hand dial.

115

116

The "Short dial" option is the short pointer and digital wheel dial.

117

118

The "Digit wheel" option is the digital wheel dial.

119

120

Now we are calibrating the digital wheel face of the water meter. Here we select "digit wheel".

121

122

(% aria-label="1713576691266-408.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:1713576691266-408.png||data-widget="image"]](% title="Click and drag to resize" %)

123

124

1:Fill in the coordinates you just got; it's best to get a coordinate and fill in a coordinate.

125

126

2: Fill in the number of number wheel on their dial,fi;

127

128

3: Select the number of short Pointers (currently we don't use short Pointers, the "digit wheelu" option defaults to 0);

129

130

4: Preview whether the setting of their coordinates is accurate;

131

132

5: Click to write all configuration to AIS;

133

134

6: Click the exit configuration interface, at this time, there will be a readout. If the Reading of "reading" is consistent with the watch face, the calibration is successful. The AIS cannot move thereafter to avoid misreading.

135

136

(% aria-label="1713576930301-479.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:1713576930301-479.png||data-widget="image"]](% title="Click and drag to resize" %)

137

138

The effect can be previewed by clicking the "Preview correction" button as shown below.

139

140

(% aria-label="1713577029535-253.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:1713577029535-253.png||data-widget="image" height="748" width="1069"]](% style="background:url(~"http://wiki.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png~") rgba(220, 220, 220, 0.5); left:0px; top:-15px" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% title="Click and drag to resize" %)

141

142

143

After the calibration process is completed, it can be observed that the obtained reading aligns consistently with the numerical value displayed on the digital wheel dial.

144

145

(% aria-label="1713577072196-132.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:1713577072196-132.png||data-widget="image" height="751" width="1073"]]

146

147

(% title="Click and drag to resize" %)

148

149

== 2.2 Calibration Power Meter ==

150

151

=== 2.2.1 Introduce ===

152

153

154

This power meter is designed in accordance with the Chinese standard for Electricity metering equipment, GB/T 17215.321-2008. It features six dial numbers for measurement accuracy.

155

156

157

=== 2.2.2 Fix Sensor to a Power Meter ===

158

159

160

You can utilize a couple of pea clips or other suitable fixtures to securely fasten the AIS sensor and ensure precise alignment of the camera with the digital watch wheel.

161

162

[[image:image-20240429091325-1.png||height="706" width="535"]]

163

164

165

=== 2.2.3 Calibration ===

166

167

168

Open the software [[HMX_FT4222H_GUI.exe>>https://www.dropbox.com/scl/fi/yktibns4o33oh0lqitqjl/HIMAX_AMR_PC_Tool.7z?rlkey=94d637ntx152idhw8vij39icv&st=4lsq8xf9&dl=0]]. Please ensure that the firmware upgrade software ota.exe is closed before opening HMX_FT4222H_GUI.exe.

169

170

For example, Select the corresponding serial port number, here 14.

171

172

(% class="box warningmessage" %)

173

(((

174

(% class="mark" %)Note: before you start the software (%%)HMX_FT4222H_GUI.exe(% class="mark" %). you must pre-install the [[visualcppredist_aio_x6_x64_v42.exe>>https://www.dropbox.com/scl/fi/mzqx6ld5a4zkcecntqjjg/VisualCppRedist_AIO_x86_x64_v42.rar?rlkey=9fuzodmed1fg9ulquh22h0dtr&st=ph6ozi4d&dl=0]] configuration environment. Otherwise, an error pop-up window occurs when running software.

175

)))

176

177

(% aria-label="1713519971789-213.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:1713519971789-213.png||data-widget="image"]]

178

179

(% title="Click and drag to resize" %)

180

181

Next, select a Baud rate of **921600** and click on **"start"**. Then, click on **"show full image"** to display the camera screen.

182

183

(% aria-label="image-20240419174908-5.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:image-20240419174908-5.png||data-widget="image" height="491" width="406"]][[image:image-20240420135207-3.png||height="485" width="706"]]

184

185

186

Click **"enable Raw"** and save the BMP image in the "Save" folder. This step is necessary to obtain the coordinate points of the watch face.

187

188

[[image:1713592384928-500.png||height="494" width="266"]][[image:image-20240420141955-4.png||height="492" width="782"]]

189

190

This power meter has only six fields, and the coordinates of the digital roulette wheel are shown in the figure.

191

192

If your device's digital scroll wheel dial does not match these six fields, you can try the other field dial coordinate dot plots in 2.4.

193

194

(% aria-label="image-20240420094632-13.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:image-20240420094632-13.png||data-widget="image" height="148" width="588"]]

195

196

The computer's drawing tool can be used to open the latest bmp image and get the coordinates of the digital wheel dial, as shown below. Based on the format of the digital wheel dial, we can obtain each coordinate point of the current use dial. The (x,y) coordinate on the image is located at the bottom left corner.

197

198

[[image:image-20240420153316-11.png||height="569" width="755"]]

199

200

201

(% id="cke_bm_67462S" style="display:none" %) (%%)Click the "ROI setting" button in "HIMAX_AMR_PC_Tool" and three options will pop up

202

203

The "Long dial" option is the long hand dial.

204

205

The "Short dial" option is the short pointer and digital wheel dial.

206

207

The "Digit wheel" option is the digital wheel dial.

208

209

Now we are calibrating the digital wheel face of the power meter. Here we select "digit wheel".

210

211

(% aria-label="1713576691266-408.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:1713576691266-408.png||data-widget="image"]](% title="Click and drag to resize" %)

212

213

1: Fill in the coordinates you just got; it's best to get a coordinate and fill in a coordinate.

214

215

2: Fill in the number of number wheel on their dial,six;

216

217

3: Select the number of short Pointers (currently we don't use short Pointers, the "digit wheelu" option defaults to 0);

218

219

4: Preview whether the setting of their coordinates is accurate;

220

221

5: Click to write all configuration to AIS;

222

223

6: Click the exit configuration interface, at this time, there will be a readout. If the Reading of "reading" is consistent with the watch face, the calibration is successful. The AIS cannot move thereafter to avoid misreading.

224

225

[[image:image-20240420143939-6.png||height="408" width="886"]](% title="Click and drag to resize" %)

226

227

The effect can be previewed by clicking the "Preview correction" button as shown below.

228

229

[[image:image-20240420144154-7.png||height="534" width="880"]]

230

231

After the calibration process is completed, it can be observed that the obtained reading aligns consistently with the numerical value displayed on the digital wheel dial.

232

233

[[image:1713595371004-125.png]]

234

235

236

== 2.3 Calibration Gas Meter ==

237

238

=== 2.3.1 Introduce ===

239

240

241

This gas meter uses G2.5 membrane gas meter. It features eight dial numbers for measurement accuracy.

242

243

244

=== 2.3.2 Fix Sensor to a Gas Meter ===

245

246

247

You can utilize a couple of pea clips or other suitable fixtures to securely fasten the AIS sensor and ensure precise alignment of the camera with the digital watch wheel.

248

249

[[image:image-20240429092436-2.png||height="676" width="519"]]

250

251

252

=== 2.3.3 Calibration ===

253

254

255

Open the software [[HMX_FT4222H_GUI.exe>>https://www.dropbox.com/scl/fi/yktibns4o33oh0lqitqjl/HIMAX_AMR_PC_Tool.7z?rlkey=94d637ntx152idhw8vij39icv&st=4lsq8xf9&dl=0]]. Please ensure that the firmware upgrade software ota.exe is closed before opening HMX_FT4222H_GUI.exe.

256

257

For example, Select the corresponding serial port number, here 14.

258

259

(% class="box warningmessage" %)

260

(((

261

(% class="mark" %)Note: before you start the software (%%)HMX_FT4222H_GUI.exe(% class="mark" %). you must pre-install the [[visualcppredist_aio_x6_x64_v42.exe>>https://www.dropbox.com/scl/fi/mzqx6ld5a4zkcecntqjjg/VisualCppRedist_AIO_x86_x64_v42.rar?rlkey=9fuzodmed1fg9ulquh22h0dtr&st=ph6ozi4d&dl=0]] configuration environment. Otherwise, an error pop-up window occurs when running software.

262

)))

263

264

(% aria-label="1713519971789-213.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:1713519971789-213.png||data-widget="image"]](% title="Click and drag to resize" %)

265

266

Next, select a Baud rate of 921600 and click on "start". Then, click on "show full image" to display the camera screen.

267

268

(% aria-label="image-20240419174908-5.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:image-20240419174908-5.png||data-widget="image" height="491" width="406"]][[image:1713598021017-402.png]]

269

270

Click "enable Raw" and save the BMP image in the "Save" folder. This step is necessary to obtain the coordinate points of the watch face.

271

272

[[image:1713592384928-500.png||height="494" width="266"]][[image:1713598094208-496.png||height="494" width="790"]]

273

274

This gas meter has eight fields, and the coordinates of the digital roulette wheel are shown in the figure.

275

276

If your device's digital scroll wheel dial does not match these eight fields, you can try the other field dial coordinate dot plots in 2.4.

277

278

(% aria-label="image-20240420094632-15.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:image-20240420094632-15.png||data-widget="image" height="113" width="542"]]

279

280

(% id="cke_bm_196694S" style="display:none" %) (%%)The computer's drawing tool can be used to open the latest bmp image and get the coordinates of the digital wheel dial, as shown below. Based on the format of the digital wheel dial, we can obtain each coordinate point of the current use dial. The (x,y) coordinate on the image is located at the bottom left corner.

281

282

[[image:image-20240420153139-10.png||height="530" width="710"]]

283

284

(% id="cke_bm_67462S" style="display:none" %) (%%)Click the "ROI setting" button in "HIMAX_AMR_PC_Tool" and three options will pop up

285

286

The "Long dial" option is the long hand dial.

287

288

The "Short dial" option is the short pointer and digital wheel dial.

289

290

The "Digit wheel" option is the digital wheel dial.

291

292

Now we are calibrating the digital wheel face of the gas meter. Here we select "digit wheel".

293

294

(% aria-label="1713576691266-408.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:1713576691266-408.png||data-widget="image"]]

295

296

1: Fill in the coordinates you just got; it's best to get a coordinate and fill in a coordinate.

297

298

2: Fill in the number of number wheel on their dial,eight;

299

300

3: Select the number of short Pointers (currently we don't use short Pointers, the "digit wheelu" option defaults to 0);

301

302

4: Preview whether the setting of their coordinates is accurate;

303

304

5: Click to write all configuration to AIS;

305

306

6: Click the exit configuration interface, at this time, there will be a readout. If the Reading of "reading" is consistent with the watch face, the calibration is successful. The AIS cannot move thereafter to avoid misreading.

307

308

[[image:image-20240420154023-12.png||height="436" width="942"]](% title="Click and drag to resize" %)

309

310

The effect can be previewed by clicking the "Preview correction" button as shown below.

311

312

[[image:1713598855240-454.png]]

313

314

After the calibration process is completed, it can be observed that the obtained reading aligns consistently with the numerical value displayed on the digital wheel dial.

315

316

[[image:1714358288601-933.png]]

317

318

319

== 2.4 Digital wheel dial take point coordinate diagram ==

4 numbers：

(% aria-label="image-20240420094632-11.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:image-20240420094632-11.png||data-widget="image" height="134" width="410"]](% style="background-image:url(http://wiki.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% title="Click and drag to resize" %)

5 numbers：

(% aria-label="image-20240420094632-12.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:image-20240420094632-12.png||data-widget="image" height="130" width="427"]](% style="background-image:url(http://wiki.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% title="Click and drag to resize" %)

6 numbers：

(% aria-label="image-20240420094632-13.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:image-20240420094632-13.png||data-widget="image" height="112" width="444"]](% style="background-image:url(http://wiki.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% title="Click and drag to resize" %)

7 numbers：

(% aria-label="image-20240420094632-14.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:image-20240420094632-14.png||data-widget="image" height="111" width="454"]](% style="background-image:url(http://wiki.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% title="Click and drag to resize" %)

8 numbers：

(% aria-label="image-20240420094632-15.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:image-20240420094632-15.png||data-widget="image"]](% style="background-image:url(http://wiki.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]]

341

342

(% title="Click and drag to resize" %)

343

344

== 2.5 Pressure Pointer Meter Calibration ==

345

346

=== 2.5.1 Introduce ===

347

348

349

The pressure pointer meter of the example is 1.6MPa range

350

351

352

=== 2.5.2 Fix Sensor to a Power Meter ===

353

354

355

You can utilize a couple of pea clips or other suitable fixtures to securely fasten the AIS sensor and ensure precise alignment of the camera with the pressure pointer meter.

356

357

[[image:image-20240516163229-1.jpeg||height="595" width="446"]]

358

359

360

=== 2.5.3 Calibration ===

361

362

363

Open the software [[HMX_FT4222H_GUI.exe>>https://www.dropbox.com/scl/fi/yktibns4o33oh0lqitqjl/HIMAX_AMR_PC_Tool.7z?rlkey=94d637ntx152idhw8vij39icv&st=4lsq8xf9&dl=0]]. Please ensure that the firmware upgrade software ota.exe is closed before opening HMX_FT4222H_GUI.exe.

364

365

For example, Select the corresponding serial port number, here 14.

366

367

(% class="box warningmessage" %)

368

(((

369

(% class="mark" %)Note: before you start the software (%%)HMX_FT4222H_GUI.exe(% class="mark" %). you must pre-install the [[visualcppredist_aio_x6_x64_v42.exe>>https://www.dropbox.com/scl/fi/mzqx6ld5a4zkcecntqjjg/VisualCppRedist_AIO_x86_x64_v42.rar?rlkey=9fuzodmed1fg9ulquh22h0dtr&st=ph6ozi4d&dl=0]] configuration environment. Otherwise, an error pop-up window occurs when running software.

370

)))

371

372

[[image:image-20240516163338-2.png||height="455" width="733"]]

373

374

375

Next, select a Baud rate of 921600 and click on "start". Then, click on "show full image" to display the camera screen.

376

377

[[image:image-20240516163423-3.png]]

378

379

380

Click **"enable Raw"** and save the BMP image in the "Save" folder. This step is necessary to obtain the coordinate points of the watch face.

381

382

[[image:image-20240516163501-4.png||height="482" width="694"]]

383

384

[[image:image-20240516163528-5.png||height="336" width="696"]]

385

386

387

The computer's drawing tool can be used to open the latest bmp image and get the coordinates of the pressure pointer meter, as shown below.

388

389

The coordinates of the pressure pointer table are located as shown below.

390

391

1 is the start point, 2 is the center point, and 3 is the end point.

392

393

The (x,y) coordinate on the image is located at the bottom left corner.

394

395

[[image:image-20240516163622-6.png||height="648" width="666"]]

396

397

398

Click on the ROI settingbutton in himax_amr_pc_tool. it will have three optionsThe long dial" option is a long dial dial.The "short dial" option is a short pointer and a number of wheel dial.The digit wheeler option is the digital wheel dial.Now the calibration is the pressure pointer table, which is long dialon."

399

400

[[image:image-20240516163910-7.png]]

401

402

403

Fill in the values of the coordinates you just got, and it's best to get one and write one

404

405

1 Coordinates of the starting point of the scale

406

407

2 Coordinates of the center point of the dial

408

409

3 Coordinates of the end of the scale

410

411

4 Starting scale value

412

413

5 End point scale value *100

414

415

After filling in the data, click "send ROI" to save the Settings and click "Cancel" to exit.

416

417

[[image:image-20240516164128-13.png||height="410" width="889"]]

418

419

420

After the calibration process is completed, The AIS cannot move thereafter to avoid misreading.

421

422

it can be observed that the obtained reading aligns consistently with the numerical value displayed on the digital wheel dial.

423

424

[[image:image-20240516164153-14.png]]

425

426

427

= (% title="Click and drag to resize" %)3. Get Sensor Data(%%) =

428

429

== (% title="Click and drag to resize" %)3.1 Get Image and show in PC(%%) ==

430

431

432

To get the AIS current image on the PC, you can connect AIS to your PC with TTL to send commands through the serial port to obtain relevant data packets.

433

434

435

=== (% style="color:inherit; font-family:inherit; font-size:23px" %)3.1.1 The image date are obtained by serial port(%%) ===

436

437

438

Select the corresponding baud rate and serial port number through the serial port tool, select HEX display and HEX send, and continuously receive data from the AIS Sensor

439

440

[[image:image-20240514161623-2.png||height="541" width="1439"]]

441

442

In the serial port to send data C0 5A 00 00 00 00 04, and then send C0 5A 00 00 00 00 09, AIS Sensor will send a real-time image of the data packet, and then stop sending. Start with FFD8 and put it in TXT file

443

444

[[image:image-20240514161658-3.png||height="544" width="1441"]]

445

446

447

=== 3.1.2 Combined image ===

448

449

450

Once all the data has been uploaded to the TTN platform, the subsequent step involves concatenating each packet in sequential order and saving it into a new TXT file. It is important to note that the first 8 bytes of each packet should be removed before concatenation.

451

452

When you combine all the packets, you need to convert the data inside to binary. Here the conversion is demonstrated using the [[WinHex>>http://www.x-ways.net/winhex/index-m.html]] software.

453

454

Open WinHex to open the combined image data file.

455

456

[[image:1714467040612-103.png||height="134" width="649"]]

457

458

459

Click on the **edit** option to choose and **convert**.

460

461