Skip to Content
Last modified by Karry Zhuang on 2025/07/03 11:59
From version 164.2
edited by Karry Zhuang
on 2024/05/16 16:38
Change comment: There is no comment for this version
To version 150.1
edited by Karry Zhuang
on 2024/05/09 18:01
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -58,9 +58,9 @@
58 58  
59 59  === 2.1.3 Calibration ===
60 60  
61 -Open the software  [[HMX_FT4222H_GUI.exe>>https://www.dropbox.com/scl/fi/yktibns4o33oh0lqitqjl/HIMAX_AMR_PC_Tool.7z?rlkey=94d637ntx152idhw8vij39icv&st=4lsq8xf9&dl=0]]. Please ensure that the firmware upgrade software ota.exe is closed before opening HMX_FT4222H_GUI.exe.
61 +Launch [[HMX_FT4222H_GUI.exe>>https://www.dropbox.com/scl/fi/yktibns4o33oh0lqitqjl/HIMAX_AMR_PC_Tool.7z?rlkey=94d637ntx152idhw8vij39icv&st=4lsq8xf9&dl=0]]. Please ensure that the firmware upgrade software ota.exe is closed before opening HMX_FT4222H_GUI.exe.
62 62  
63 -Choose the largest number of serial port, for example, Select the corresponding serial port number, here 14.
63 +Choose the largest number of serial port, for example, here shows 13 and 14, then choose 14.
64 64  
65 65  (% class="box warningmessage" %)
66 66  (((
... ... @@ -140,13 +140,13 @@
140 140  
141 141  === 2.2.3 Calibration ===
142 142  
143 -Open the software  [[HMX_FT4222H_GUI.exe>>https://www.dropbox.com/scl/fi/yktibns4o33oh0lqitqjl/HIMAX_AMR_PC_Tool.7z?rlkey=94d637ntx152idhw8vij39icv&st=4lsq8xf9&dl=0]]. Please ensure that the firmware upgrade software ota.exe is closed before opening HMX_FT4222H_GUI.exe.
143 +Perform a power reset on the EVB board, making sure to close the ota.exe program before opening HMX_FT4222H_GUI.exe.
144 144  
145 -Choose the largest number of serial port, for example, Select the corresponding serial port number, here 14.
145 +Choose the largest number of serial port, for example, here shows 13 and 14, then choose 14.
146 146  
147 147  (% class="box warningmessage" %)
148 148  (((
149 -(% class="mark" %)Note: before you start the software (%%)HMX_FT4222H_GUI.exe(% class="mark" %). you must pre-install the [[visualcppredist_aio_x6_x64_v42.exe>>https://www.dropbox.com/scl/fi/mzqx6ld5a4zkcecntqjjg/VisualCppRedist_AIO_x86_x64_v42.rar?rlkey=9fuzodmed1fg9ulquh22h0dtr&st=ph6ozi4d&dl=0]] configuration environment. Otherwise, an error pop-up window occurs when running software.
149 +(% class="mark" %)Note: before you start the software (%%)HMX_FT4222H_GUI.exe(% class="mark" %). you must pre-install the visualcppredist_aio_x6_x64_v42.exe configuration environment. Otherwise, an error pop-up window occurs when running software.
150 150  )))
151 151  
152 152  (% aria-label="1713519971789-213.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:1713519971789-213.png||data-widget="image"]](% title="Click and drag to resize" %)​
... ... @@ -219,13 +219,13 @@
219 219  
220 220  === 2.3.3 Calibration ===
221 221  
222 -Open the software  [[HMX_FT4222H_GUI.exe>>https://www.dropbox.com/scl/fi/yktibns4o33oh0lqitqjl/HIMAX_AMR_PC_Tool.7z?rlkey=94d637ntx152idhw8vij39icv&st=4lsq8xf9&dl=0]]. Please ensure that the firmware upgrade software ota.exe is closed before opening HMX_FT4222H_GUI.exe.
222 +Perform a power reset on the EVB board, making sure to close the ota.exe program before opening HMX_FT4222H_GUI.exe.
223 223  
224 -Choose the largest number of serial port, for example, Select the corresponding serial port number, here 14.
224 +Choose the largest number of serial port, for example, here shows 13 and 14, then choose 14.
225 225  
226 226  (% class="box warningmessage" %)
227 227  (((
228 -(% class="mark" %)Note: before you start the software (%%)HMX_FT4222H_GUI.exe(% class="mark" %). you must pre-install the [[visualcppredist_aio_x6_x64_v42.exe>>https://www.dropbox.com/scl/fi/mzqx6ld5a4zkcecntqjjg/VisualCppRedist_AIO_x86_x64_v42.rar?rlkey=9fuzodmed1fg9ulquh22h0dtr&st=ph6ozi4d&dl=0]] configuration environment. Otherwise, an error pop-up window occurs when running software.
228 +(% class="mark" %)Note: before you start the software (%%)HMX_FT4222H_GUI.exe(% class="mark" %). you must pre-install the visualcppredist_aio_x6_x64_v42.exe configuration environment. Otherwise, an error pop-up window occurs when running software.
229 229  )))
230 230  
231 231  (% aria-label="1713519971789-213.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:1713519971789-213.png||data-widget="image"]](% title="Click and drag to resize" %)​
... ... @@ -302,82 +302,112 @@
302 302  
303 303  8 numbers：
304 304  
305 -(% aria-label="image-20240420094632-15.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:image-20240420094632-15.png||data-widget="image"]](% style="background-image:url(http://wiki.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]]
305 +(% aria-label="image-20240420094632-15.png image widget" contenteditable="false" role="region" tabindex="-1" %)[[image:image-20240420094632-15.png||data-widget="image"]](% style="background-image:url(http://wiki.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% title="Click and drag to resize" %)​
306 306  
307 -(% title="Click and drag to resize" %)​
308 308  
309 -== 2.5 Pressure Pointer Meter Calibration ==
308 += (% title="Click and drag to resize" %)3. Get Sensor Data.(%%) =
310 310  
311 -=== 2.5.1 Introduce ===
310 +== (% title="Click and drag to resize" %)3.1 Get Digital Reading After Calibration(%%) ==
312 312  
313 -The pressure pointer meter of the example is 1.6MPa range
312 +This section shows an example for how to join the [[TheThingsNetwork>>url:https://www.thethingsnetwork.org/]] LoRaWAN IoT server. Usages with other LoRaWAN IoT servers are of similar procedure.
314 314  
315 -=== 2.5.2 Fix Sensor to a Power Meter​ ===
316 316  
317 -You can utilize a couple of pea clips or other suitable fixtures to securely fasten the AIS sensor and ensure precise alignment of the camera with the pressure pointer meter.
315 +Assume the DLOS8 is already set to connect to [[TTN V3 network >>url:https://eu1.cloud.thethings.network/]]. We need to add the AIS Sensor device in TTN V3 portal. 
318 318  
319 -[[image:image-20240516163229-1.jpeg||height="595" width="446"]]
317 +**Step 1**:  Create a device in TTN V3 with the OTAA keys from AIS Sensor.
320 320  
321 -=== 2.5.3 Calibration ===
319 +Each AIS Sensor is shipped with a sticker with the default DEV EUI as below:
322 322  
323 -Open the software  [[HMX_FT4222H_GUI.exe>>https://www.dropbox.com/scl/fi/yktibns4o33oh0lqitqjl/HIMAX_AMR_PC_Tool.7z?rlkey=94d637ntx152idhw8vij39icv&st=4lsq8xf9&dl=0]]. Please ensure that the firmware upgrade software ota.exe is closed before opening HMX_FT4222H_GUI.exe.
321 +[[image:image-20240430155056-2.png||height="207" width="450"]]
324 324  
325 -Choose the largest number of serial port, for example, Select the corresponding serial port number, here 14.
323 +Enter these keys in the LoRaWAN Server portal. Below is TTN V3 screen shot:
326 326  
327 -(% class="box warningmessage" %)
328 -(((
329 -(% class="mark" %)Note: before you start the software (%%)HMX_FT4222H_GUI.exe(% class="mark" %). you must pre-install the [[visualcppredist_aio_x6_x64_v42.exe>>https://www.dropbox.com/scl/fi/mzqx6ld5a4zkcecntqjjg/VisualCppRedist_AIO_x86_x64_v42.rar?rlkey=9fuzodmed1fg9ulquh22h0dtr&st=ph6ozi4d&dl=0]] configuration environment. Otherwise, an error pop-up window occurs when running software.
330 -)))
325 +Add APP EUI in the application.
331 331  
332 -[[image:image-20240516163338-2.png||height="455" width="733"]]
327 +choose to create the device manually.
333 333  
329 +Add APP KEY and DEV EUI
334 334  
335 -Next, select a Baud rate of 921600 and click on "start". Then, click on "show full image" to display the camera screen.
331 +[[image:image-20240430155117-3.png||height="544" width="563"]]
336 336  
337 -[[image:image-20240516163423-3.png]]
333 +[[image:image-20240430154736-1.png||height="414" width="658"]]
338 338  
339 339  
340 -Click "enable Raw" and save the BMP image in the "Save" folder. This step is necessary to obtain the coordinate points of the watch face.
336 +**Default mode OTAA**
341 341  
342 -[[image:image-20240516163501-4.png||height="482" width="694"]]
338 +[[image:image-20240430155302-4.png||height="630" width="453"]]
343 343  
344 -[[image:image-20240516163528-5.png||height="336" width="696"]]
340 +**Step 2**:  Use ACT button to activate LHT52 and it will auto join to the TTN V3 network. After join success, it will start to upload sensor data to TTN V3 and user can see in the panel.
345 345  
342 +=== 3.1.1 Uplink Payload (Fport~=2) ===
346 346  
347 -The computer's drawing tool can be used to open the latest bmp image and get the coordinates of the pressure pointer meter, as shown below.
344 +The uplink payload includes totally 14 bytes. Uplink packets use FPORT=2 and (% style="color:#4472c4" %)**every 20 minutes**(%%) send one uplink by default.
348 348  
349 -The coordinates of the pressure pointer table are located as shown below.
346 +(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:370px" %)
347 +|=(% style="width: 60px;background-color:#4F81BD;color:white" %)**Size(bytes)(% style="display:none" %) (%%)**|=(% style="width: 60px;background-color:#4F81BD;color:white" %)2|=(% style="width: 80px;background-color:#4F81BD;color:white" %)4|=(% style="width: 80px;background-color:#4F81BD;color:white" %)4|=(% style="width: 60px;background-color:#4F81BD;color:white" %)4
348 +|(% style="width:99px" %)Value|(% style="width:62px" %)BAT|sysTimeCurrent|Integer|Decimal
350 350  
351 -1 is the start point, 2 is the center point, and 3 is the end point.
350 +[[image:1714374026505-898.png||height="200" width="736"]]
352 352  
353 -The (x,y) coordinate on the image is located at the bottom left corner.
352 +Payload Example（FPort=2）：(% style="background-color:yellow" %)**0D 32 66 29 AF E0 00 00 00 02 00 05 E3 B0**
354 354  
355 -[[image:image-20240516163622-6.png||height="648" width="666"]]
354 +=== 3.1.2 BAT- Battery information ===
356 356  
356 +These two bytes of BAT include the battery state and the actual voltage.
357 357  
358 +**Ex**：0x0B32 = 3378mV
358 358  
360 +=== 3.1.3 sysTimeCurrent ===
359 359  
362 +These four bytes contain the year, month, day, hour, minute, and second of the time.
360 360  
364 +AI Sensor use Unix TimeStamp format based on
361 361  
362 -= (% title="Click and drag to resize" %)3. Get Sensor Data.(%%) =
366 +[[image:1714374373681-339.png||height="81" width="527"]]
363 363  
368 +Users can get this time from the link:  [[https:~~/~~/www.epochconverter.com/>>url:https://www.epochconverter.com/]] :
364 364  
365 -== (% title="Click and drag to resize" %)3.1 Get Image and show in PC(%%) ==
370 +Below is the converter example
366 366  
372 +**Ex**：6629AFE0=2024-04-25 01:20:32
373 +
374 +[[image:1714374389825-148.png||height="313" width="428"]][[image:1714374398047-940.png||height="214" width="508"]]
375 +
376 +So, we can use AT+TIMESTAMP=1714012723 or downlink 6629C233 to set the current time 2024 – April ~-~- 25 Thursday 02:38:41
377 +
378 +=== 3.1.4 Integer ===
379 +
380 +These four bytes display the integers in the digital wheel face
381 +
382 +[[image:1714374445395-196.png]]
383 +
384 +Read table integer：0x00000002=2
385 +
386 +=== 3.1.5 Decimal ===
387 +
388 +These four bytes display decimals on the digital wheel.
389 +
390 +[[image:1714374493101-914.png]]
391 +
392 +Read table decimals：0x005E3B0/1000000= 0.385968
393 +
394 +
395 +== (% title="Click and drag to resize" %)3.2 Get Image and show in PC(%%) ==
396 +
367 367  To get the AIS current image on the PC, you can  connect AIS to your PC with TTL to send commands through the serial port to obtain relevant data packets.
368 368  
369 -=== (% id="cke_bm_3839S" style="display:none" %) (%%)3.1.1 The image date are obtained by serial port ===
399 +=== (% id="cke_bm_3839S" style="display:none" %) (%%)3.2.1 The image date are obtained by serial port ===
370 370  
371 371  Select the corresponding baud rate and serial port number through the serial port tool, select HEX display and HEX send, and continuously receive data from the AIS Sensor
372 372  
373 -[[image:image-20240514161623-2.png||height="541" width="1439"]]
403 +[[image:1714985699187-406.png||height="277" width="536"]]
374 374  
375 375  In the serial port to send data C0 5A 00 00 00 00 04, and then send C0 5A 00 00 00 00 09, AIS Sensor will send a real-time image of the data packet, and then stop sending. Start with FFD8 and put it in TXT file
376 376  
377 -[[image:image-20240514161658-3.png||height="544" width="1441"]]
407 +[[image:1714985711524-251.png||height="140" width="526"]]
378 378  
379 379  
380 -=== 3.1.2 Combined image ===
410 +=== 3.2.2 Combined image ===
381 381  
382 382  Once all the data has been uploaded to the TTN platform, the subsequent step involves concatenating each packet in sequential order and saving it into a new TXT file. It is important to note that the first 8 bytes of each packet should be removed before concatenation.
383 383  
... ... @@ -410,4 +410,154 @@
410 410  === ===
411 411  
412 412  
413 -= =
443 += 4. Configure AIS Sensor using AT commands =
444 +
445 +== 4.1 Configure Methods ==
446 +
447 +
448 + configure method:
449 +
450 +* AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].
451 +* AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].
452 +* LoRaWAN Downlink.  Instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.
453 +
454 +== 4.2 General Commands ==
455 +
456 +
457 +These commands are to configure:
458 +
459 +* General system settings like: uplink interval.
460 +* LoRaWAN protocol & radio related command.
461 +
462 +They are same for all Dragino Devices which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:
463 +
464 +[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
465 +
466 +== 4.3 Commands special design for AIS Sensor ==
467 +
468 +=== 4.3.1 Change Uplink Interval ===
469 +
470 +
471 +Feature: Change LoRaWAN End Node Transmit Interval.
472 +
473 +
474 +(% style="color:blue" %)**AT Command: AT+TDC**
475 +
476 +(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:727.222px" %)
477 +|(% style="background-color:#4f81bd; color:white; width:165px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:227px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:329px" %)**Response**
478 +|(% style="width:165px" %)AT+TDC=?|(% style="width:227px" %)Show current transmit Interval|(% style="width:329px" %)30000(((
479 +OK
480 +
481 +the interval is 30000ms = 30s
482 +)))
483 +|(% style="width:165px" %)AT+TDC=60000|(% style="width:227px" %)Set Transmit Interval|(% style="width:329px" %)OK(((
484 +Set transmit interval to 60000ms = 60 seconds
485 +)))
486 +
487 +(((
488 +(% style="color:blue" %)**Downlink Command: 0x01**
489 +
490 +Format: Command Code (0x01) followed by 3 bytes time value.
491 +)))
492 +
493 +(((
494 +If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
495 +)))
496 +
497 +* **Example 1**: Downlink Payload:** 0100001E**  ~/~/ Set Transmit Interval (TDC) = 30 seconds
498 +
499 +* **Example 2**: Downlink Payload:** 0100003C**  ~/~/ Set Transmit Interval (TDC) = 60 seconds
500 +
501 +(% style="display:none" %) (%%)
502 +
503 +== 4.3.2 Request the server to send an ACK ==
504 +
505 +
506 +(% style="color:blue" %)**AT Command: AT+PNACKMD**
507 +
508 +(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:889px" %)
509 +|(% style="background-color:#4f81bd; color:white; width:160px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:627px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:100px" %)**Response**
510 +|(% style="width:160px" %)AT+PNACKMD=1|(% style="width:627px" %)If the node uploads the ACK as confirm, it will request the server to send an ACK. If the server ack is not received, the node will upload the packets that have not received the ACK the next time it receives the ACK|(% style="width:100px" %)1(((
511 +OK
512 +)))
513 +|(% style="width:160px" %)AT+PNACKMD=0|(% style="width:627px" %)off request the server to send an ACK|(% style="width:100px" %)(((
514 +0
515 +OK
516 +)))
517 +
518 +(% style="display:none" %) (%%) (% style="color:blue" %)**Downlink Command: 0x34**
519 +
520 +0X34 01  ~/~/Same As AT+PNACKMD=1
521 +
522 +0x34 00  ~/~/Same As AT+PNACKMD=0
523 +
524 +
525 +=== 4.3.3 Set Interrupt Mode ===
526 +
527 +
528 +Feature, Set Interrupt mode for GPIO_EXIT.
529 +
530 +(% style="color:blue" %)**AT Command: AT+INTMOD1,AT+INTMOD2,AT+INTMOD3**
531 +
532 +(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
533 +|=(% style="width: 155px;background-color:#4F81BD;color:white" %)**Command Example**|=(% style="width: 197px;background-color:#4F81BD;color:white" %)**Function**|=(% style="width: 158px;background-color:#4F81BD;color:white" %)**Response**
534 +|(% style="width:154px" %)AT+INTMOD1=?|(% style="width:196px" %)Show current interrupt mode|(% style="width:157px" %)(((
535 +0
536 +OK
537 +the mode is 0 =Disable Interrupt
538 +)))
539 +|(% style="width:154px" %)AT+INTMOD1=2|(% style="width:196px" %)(((
540 +Set Transmit Interval
541 +0. (Disable Interrupt),
542 +~1. (Trigger by rising and falling edge)
543 +2. (Trigger by falling edge)
544 +3. (Trigger by rising edge)
545 +)))|(% style="width:157px" %)OK
546 +|(% style="width:154px" %)AT+INTMOD2=3|(% style="width:196px" %)Set Transmit Interval
547 +0. (Disable Interrupt),
548 +~1. (Trigger by rising and falling edge)
549 +2. (Trigger by falling edge)
550 +3. (Trigger by rising edge)|(% style="width:157px" %)OK
551 +
552 +(% style="color:blue" %)**Downlink Command: 0x06**
553 +
554 +Format: Command Code (0x06) followed by 3 bytes.
555 +
556 +This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
557 +
558 +* Example 1: Downlink Payload: 06000000  **~-~-->**  AT+INTMOD1=0
559 +* Example 2: Downlink Payload: 06000003  **~-~-->**  AT+INTMOD1=3
560 +* Example 3: Downlink Payload: 06000102  **~-~-->**  AT+INTMOD2=2
561 +
562 +=== ===
563 +
564 +=== 4.3.4 Clock logging (Since firmware version v1.2.1) ===
565 +
566 +
567 +Sometimes when we deploy lots of end nodes in field. We want all sensors sample data at the same time, and upload these data together for analyze. In such case, we can use clock loging feature.
568 +
569 +We can use this command to set the start time of data recording and the time interval to meet the requirements of the specific collection time of data.
570 +
571 +* (% style="color:blue" %)**AT Command:**(%%)** (% style="color:#037691" %)AT+CLOCKLOG=a,b,c,d(%%)**
572 +
573 +(% style="color:#037691" %)**a: **(%%)**0:** Disable Clock logging.  ** 1: **Enable Clock Logging
574 +
575 +(% style="color:#037691" %)**b: **(%%)Specify First sampling start second: range **(0 ~~ 3599, 65535)   ** ~/~/ (% style="color:red" %)**Note:**(%%)** **If parameter b is set to 65535, the log period starts after the node accesses the network and sends packets.
576 +
577 +(% style="color:#037691" %)**c: **(%%)Specify the sampling interval: range **(0 ~~ 255 minutes)**
578 +
579 +(% style="color:#037691" %)**d:**(%%)How many entries should be uplink on every TDC **(max 32)**
580 +
581 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SPH01-NB_NB-IoT_Soil_pH_Sensor_User_Manual/WebHome/image-20240315141254-1.png?rev=1.1||alt="image-20240315141254-1.png"]]
582 +
583 +**Example:**
584 +
585 +**AT+CLOCKLOG=1,65535,1,5**
586 +
587 +After the node sends the first packet, data is recorded to the memory at intervals of 1 minute. For each TDC uplink, the uplink load will include: battery information + the last 5 memory records (payload + timestamp).
588 +
589 +(% class="wikigeneratedid" %)
590 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/TS01-NB_NB-IoT_Tilting_Sensor_User_Manual/WebHome/image-20240316163501-1.png?width=1064&height=517&rev=1.1||alt="image-20240316163501-1.png"]]
591 +
592 +(% class="wikigeneratedid" %)
593 +(% style="color:red" %)**Note: Users need to synchronize the server time before configuring this command. If the server time is not synchronized before this command is configured, the command takes effect only after the node is reset.**
image-20240514161559-1.jpeg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.karry
Size
... ... @@ -1,1 +1,0 @@
1 -436.9 KB
Content
image-20240514161623-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.karry
Size
... ... @@ -1,1 +1,0 @@
1 -549.0 KB
Content
image-20240514161658-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.karry
Size
... ... @@ -1,1 +1,0 @@
1 -552.4 KB
Content
image-20240516163229-1.jpeg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.karry
Size
... ... @@ -1,1 +1,0 @@
1 -159.5 KB
Content
image-20240516163338-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.karry
Size
... ... @@ -1,1 +1,0 @@
1 -1.6 MB
Content
image-20240516163423-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.karry
Size
... ... @@ -1,1 +1,0 @@
1 -1.2 MB
Content
image-20240516163501-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.karry
Size
... ... @@ -1,1 +1,0 @@
1 -282.7 KB
Content
image-20240516163528-5.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.karry
Size
... ... @@ -1,1 +1,0 @@
1 -537.1 KB
Content
image-20240516163622-6.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.karry
Size
... ... @@ -1,1 +1,0 @@
1 -2.6 MB
Content