RS485-BL – Waterproof RS485 to LoRaWAN Converter

The Dragino RS485-BL is a **RS485 / UART to LoRaWAN Converter** for Internet of Things solutions. User can connect RS485 or UART sensor to RS485-BL converter, and configure RS485-BL to periodically read sensor data and upload via LoRaWAN network to IoT server.

26

)))

27

28

(((

29

RS485-BL can interface to RS485 sensor, 3.3v/5v UART sensor or interrupt sensor. RS485-BL provides **a 3.3v output** and** a 5v output** to power external sensors. Both output voltages are controllable to minimize the total system power consumption.

)))

(((

RS485-BL is IP67 **waterproof** and powered by **8500mAh Li-SOCI2 battery**, it is designed for long term use for several years.

)))

(((

RS485-BL runs standard **LoRaWAN 1.0.3 in Class A**. It can reach long transfer range and easy to integrate with LoRaWAN compatible gateway and IoT server.

)))

(((

For data uplink, RS485-BL sends user-defined commands to RS485 devices and gets the return from the RS485 devices. RS485-BL will process these returns data according to user-define rules to get the final payload and upload to LoRaWAN server.

)))

(((

For data downlink, RS485-BL runs in LoRaWAN Class A. When there is downlink commands from LoRaWAN server, RS485-BL will forward the commands from LoRaWAN server to RS485 devices.

)))

(((

Each RS485-BL pre-load with a set of unique keys for LoRaWAN registration, register these keys to LoRaWAN server and it will auto connect after power on.

50

)))

51

52

[[image:1652953304999-717.png||height="424" width="733"]]

53

54

== 1.2 Specifications ==

**Hardware System:**

* STM32L072CZT6 MCU

* SX1276/78 Wireless Chip

60

* Power Consumption (exclude RS485 device):

** Idle: 6uA@3.3v

*

** 20dB Transmit: 130mA@3.3v

65

66

**Interface for Model:**

67

68

* 1 x RS485 Interface

69

* 1 x TTL Serial , 3.3v or 5v.

70

* 1 x I2C Interface, 3.3v or 5v.

71

* 1 x one wire interface

72

* 1 x Interrupt Interface

73

* 1 x Controllable 5V output, max

**LoRa Spec:**

* Frequency Range:

** Band 1 (HF): 862 ~~ 1020 Mhz

79

** Band 2 (LF): 410 ~~ 528 Mhz

80

* 168 dB maximum link budget.

81

* +20 dBm - 100 mW constant RF output vs.

82

* Programmable bit rate up to 300 kbps.

83

* High sensitivity: down to -148 dBm.

84

* Bullet-proof front end: IIP3 = -12.5 dBm.

85

* Excellent blocking immunity.

86

* Fully integrated synthesizer with a resolution of 61 Hz.

87

* LoRa modulation.

88

* Built-in bit synchronizer for clock recovery.

89

* Preamble detection.

90

* 127 dB Dynamic Range RSSI.

91

* Automatic RF Sense and CAD with ultra-fast AFC.

== 1.3 Features ==

* LoRaWAN Class A & Class C protocol (default Class A)

96

* Frequency Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865/RU864

97

* AT Commands to change parameters

98

* Remote configure parameters via LoRaWAN Downlink

99

* Firmware upgradable via program port

100

* Support multiply RS485 devices by flexible rules

101

* Support Modbus protocol

102

* Support Interrupt uplink

103

104

== 1.4 Applications ==

105

106

* Smart Buildings & Home Automation

107

* Logistics and Supply Chain Management

* Smart Metering

* Smart Agriculture

* Smart Cities

* Smart Factory

== 1.5 Firmware Change log ==

114

115

[[RS485-BL Image files – Download link and Change log>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/RS485-BL/Firmware/||style="background-color: rgb(255, 255, 255);"]]

116

117

== 1.6 Hardware Change log ==

(((

v1.4

)))

(((

~1. Change Power IC to TPS22916

)))

(((

v1.3

)))

(((

~1. Change JP3 from KF350-8P to KF350-11P, Add one extra interface for I2C and one extra interface for one-wire

)))

(((

v1.2

)))

(((

Release version

)))

= 2. Pin mapping and Power ON Device =

146

147

(((

148

The RS485-BL is powered on by 8500mAh battery. To save battery life, RS485-BL is shipped with power off. User can put the jumper to power on RS485-BL.

149

)))

150

151

[[image:1652953055962-143.png||height="387" width="728"]]

152

153

154

The Left TXD and RXD are TTL interface for external sensor. TTL level is controlled by 3.3/5v Jumper.

155

156

= 3. Operation Mode =

157

158

== 3.1 How it works? ==

159

160

(((

161

The RS485-BL is configured as LoRaWAN OTAA Class A mode by default. It has OTAA keys to join network. To connect a local LoRaWAN network, user just need to input the OTAA keys in the network server and power on the RS485-BL. It will auto join the network via OTAA.

162

)))

163

164

== 3.2 Example to join LoRaWAN network ==

165

166

Here shows an example for how to join the TTN V3 Network. Below is the network structure, we use [[LG308>>url:http://www.dragino.com/products/lora-lorawan-gateway/item/140-lg308.html]] as LoRaWAN gateway here.

167

168

[[image:1652953414711-647.png||height="337" width="723"]]

169

170

(((

171

The RS485-BL in this example connected to two RS485 devices for demonstration, user can connect to other RS485 devices via the same method.

)))

(((

The LG308 is already set to connect to [[TTN V3 network >>url:https://www.thethingsnetwork.org/]]. So what we need to now is only configure the TTN V3:

)))

(((

**Step 1**: Create a device in TTN V3 with the OTAA keys from RS485-BL.

)))

(((

Each RS485-BL is shipped with a sticker with unique device EUI:

184

)))

185

186

[[image:1652953462722-299.png]]

187

188

(((

189

User can enter this key in their LoRaWAN Server portal. Below is TTN V3 screen shot:

)))

(((

Add APP EUI in the application.

)))

[[image:image-20220519174512-1.png]]

200

201

[[image:image-20220519174512-2.png||height="328" width="731"]]

202

203

[[image:image-20220519174512-3.png||height="556" width="724"]]

204

205

[[image:image-20220519174512-4.png]]

206

207

You can also choose to create the device manually.

208

209

[[image:1652953542269-423.png||height="710" width="723"]]

210

211

Add APP KEY and DEV EUI

212

213

[[image:1652953553383-907.png||height="514" width="724"]]

(((

**Step 2**: Power on RS485-BL and it will auto join to the TTN V3 network. After join success, it will start to upload message to TTN V3 and user can see in the panel.

218

)))

219

220

[[image:1652953568895-172.png||height="232" width="724"]]

221

222

== 3.3 Configure Commands to read data ==

223

224

(((

225

There are plenty of RS485 and TTL level devices in the market and each device has different command to read the valid data. To support these devices in flexible, RS485-BL supports flexible command set. User can use [[AT Commands or LoRaWAN Downlink>>path:#AT_COMMAND]] Command to configure how RS485-BL should read the sensor and how to handle the return from RS485 or TTL sensors.

226

)))

227

228

=== 3.3.1 onfigure UART settings for RS485 or TTL communication ===

229

230

RS485-BL can connect to either RS485 sensors or TTL sensor. User need to specify what type of sensor need to connect.

231

232

**~1. RS485-MODBUS mode:**

233

234

AT+MOD=1 ~/~/ Support RS485-MODBUS type sensors. User can connect multiply RS485 , Modbus sensors to the A / B pins.

**2. TTL mode:**

AT+MOD=2 ~/~/ Support TTL Level sensors, User can connect one TTL Sensor to the TXD/RXD/GND pins.

239

240

RS485-BL default UART settings is **9600, no parity, stop bit 1**. If the sensor has a different settings, user can change the RS485-BL setting to match.

241

242

(% border="1" style="background-color:#ffffcc; color:green; width:795px" %)

243

|(((

244

**AT Commands**

245

)))|(% style="width:285px" %)(((

246

**Description**

247

)))|(% style="width:347px" %)(((

**Example**

)))

|(((

AT+BAUDR

)))|(% style="width:285px" %)(((

253

Set the baud rate (for RS485 connection). Default Value is: 9600.

254

)))|(% style="width:347px" %)(((

(((

AT+BAUDR=9600

)))

(((

Options: (1200,2400,4800,14400,19200,115200)

)))

)))

|(((

AT+PARITY

)))|(% style="width:285px" %)(((

266

(((

267

Set UART parity (for RS485 connection)

)))

(((

Default Value is: no parity.

272

)))

273

)))|(% style="width:347px" %)(((

(((

AT+PARITY=0

)))

(((

Option: 0: no parity, 1: odd parity, 2: even parity

)))

)))

|(((

AT+STOPBIT

)))|(% style="width:285px" %)(((

285

(((

286

Set serial stopbit (for RS485 connection)

)))

(((

Default Value is: 1bit.

291

)))

292

)))|(% style="width:347px" %)(((

293

(((

294

AT+STOPBIT=0 for 1bit

)))

(((

AT+STOPBIT=1 for 1.5 bit

)))

(((

AT+STOPBIT=2 for 2 bits

)))

)))

=== 3.3.2 Configure sensors ===

307

308

(((

309

Some sensors might need to configure before normal operation. User can configure such sensor via PC or through RS485-BL AT Commands (% style="color:#4f81bd" %)**AT+CFGDEV**.

)))

(((

When user issue an (% style="color:#4f81bd" %)**AT+CFGDEV**(%%) command, Each (% style="color:#4f81bd" %)**AT+CFGDEV**(%%) equals to send a command to the RS485 or TTL sensors. This command will only run when user input it and won’t run during each sampling.

314

)))

315

316

(% border="1" style="background-color:#ffffcc; color:green; width:806px" %)

317

|**AT Commands**|(% style="width:418px" %)**Description**|(% style="width:256px" %)**Example**

318

|AT+CFGDEV|(% style="width:418px" %)(((

319

This command is used to configure the RS485/TTL devices; they won’t be used during sampling.

320

321

AT+CFGDEV=xx xx xx xx xx xx xx xx xx xx xx xx,

322

323

mm: 0: no CRC, 1: add CRC-16/MODBUS in the end of this command

324

)))|(% style="width:256px" %)AT+CFGDEV=xx xx xx xx xx xx xx xx xx xx xx xx,m

325

326

Detail of AT+CFGDEV command see [[AT+CFGDEV detail>>path:#AT_CFGDEV]].

327

328

=== 3.3.3 Configure read commands for each sampling ===

329

330

(((

331

RS485-BL is a battery powered device; it will sleep most of time. And wake up on each period and read RS485 / TTL sensor data and uplink.

)))

(((

During each sampling, we need to confirm what commands we need to send to the sensors to read data. After the RS485/TTL sensors send back the value, it normally includes some bytes and we only need a few from them for a shorten payload.

)))

(((

To save the LoRaWAN network bandwidth, we might need to read data from different sensors and combine their valid value into a short payload.

)))

(((

This section describes how to achieve above goals.

)))

(((

During each sampling, the RS485-BL can support 15 commands to read sensors. And combine the return to one or several uplink payloads.

)))

(((

**Command from RS485-BL to Sensor:**

)))

(((

RS485-BL can send out pre-set max 15 strings via **AT+COMMAD1**, **ATCOMMAND2**,…, to **AT+COMMANDF** . All commands are of same grammar.

)))

(((

**Handle return from sensors to RS485-BL**:

)))

(((

After RS485-BL send out a string to sensor, RS485-BL will wait for the return from RS485 or TTL sensor. And user can specify how to handle the return, by **AT+DATACUT or AT+SEARCH commands**

)))

* (((

**AT+DATACUT**

)))

(((

When the return value from sensor have fix length and we know which position the valid value we should get, we can use AT+DATACUT command.

)))

* (((

**AT+SEARCH**

)))

(((

When the return value from sensor is dynamic length and we are not sure which bytes the valid data is, instead, we know what value the valid value following. We can use AT+SEARCH to search the valid value in the return string.

)))

(((

**Define wait timeout:**

)))

(((

Some RS485 device might has longer delay on reply, so user can use AT+CMDDL to set the timeout for getting reply after the RS485 command is sent. For example, AT+CMDDL1=1000 to send the open time to 1000ms

)))

(((

After we got the valid value from each RS485 commands, we need to combine them together with the command **AT+DATAUP**.

)))

**Examples:**

Below are examples for the how above AT Commands works.

397

398

**AT+COMMANDx : **This command will be sent to RS485/TTL devices during each sampling, Max command length is 14 bytes. The grammar is:

399

400

(% border="1" class="table-bordered" %)

401

|(((

402

**AT+COMMANDx=xx xx xx xx xx xx xx xx xx xx xx xx,m**

403

404

**xx xx xx xx xx xx xx xx xx xx xx xx: The RS485 command to be sent**

405

406

**m: 0: no CRC, 1: add CRC-16/MODBUS in the end of this command**

407

)))

408

409

For example, if we have a RS485 sensor. The command to get sensor value is: 01 03 0B B8 00 02 46 0A. Where 01 03 0B B8 00 02 is the Modbus command to read the register 0B B8 where stored the sensor value. The 46 0A is the CRC-16/MODBUS which calculate manually.

410

411

In the RS485-BL, we should use this command AT+COMMAND1=01 03 0B B8 00 02,1 for the same.

412

413

**AT+SEARCHx**: This command defines how to handle the return from AT+COMMANDx.

414

415

(% border="1" class="table-bordered" %)

416

|(((

417

**AT+SEARCHx=aa,xx xx xx xx xx**

418

419

* **aa: 1: prefix match mode; 2: prefix and suffix match mode**

420

* **xx xx xx xx xx: match string. Max 5 bytes for prefix and 5 bytes for suffix**

)))

Examples:

1. For a return string from AT+COMMAND1: 16 0c 1e 56 34 2e 30 58 5f 36 41 30 31 00 49

428

429

If we set AT+SEARCH1=1,1E 56 34. (max 5 bytes for prefix)

430

431

The valid data will be all bytes after 1E 56 34 , so it is 2e 30 58 5f 36 41 30 31 00 49

432

433

[[image:1652954654347-831.png]]

434

435

436

1. For a return string from AT+COMMAND1: 16 0c 1e 56 34 2e 30 58 5f 36 41 30 31 00 49

437

438

If we set AT+SEARCH1=2, 1E 56 34+31 00 49

439

440

Device will search the bytes between 1E 56 34 and 31 00 49. So it is 2e 30 58 5f 36 41 30

441

442

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image014.png]]

443

444

445

**AT+DATACUTx : **This command defines how to handle the return from AT+COMMANDx, max return length is 45 bytes.

446

447

|(((

448

**AT+DATACUTx=a,b,c**

449

450

* **a: length for the return of AT+COMMAND**

451

* **b:1: grab valid value by byte, max 6 bytes. 2: grab valid value by bytes section, max 3 sections.**

452

* **c: define the position for valid value. **

)))

Examples:

* Grab bytes:

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image015.png]]

* Grab a section.

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image016.png]]

464

465

* Grab different sections.

466

467

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image017.png]]

Note:

AT+SEARCHx and AT+DATACUTx can be used together, if both commands are set, RS485-BL will first process AT+SEARCHx on the return string and get a temporary string, and then process AT+DATACUTx on this temporary string to get the final payload. In this case, AT+DATACUTx need to set to format AT+DATACUTx=0,xx,xx where the return bytes set to 0.

Example:

AT+COMMAND1=11 01 1E D0,0

477

478

AT+SEARCH1=1,1E 56 34

AT+DATACUT1=0,2,1~~5

Return string from AT+COMMAND1: 16 0c 1e 56 34 2e 30 58 5f 36 41 30 31 00 49

483

484

String after SEARCH command: 2e 30 58 5f 36 41 30 31 00 49

485

486

Valid payload after DataCUT command: 2e 30 58 5f 36

487

488

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image018.png]]

1.

11.

111. Compose the uplink payload

496

497

Through AT+COMMANDx and AT+DATACUTx we got valid value from each RS485 commands, Assume these valid value are RETURN1, RETURN2, .., to RETURNx. The next step is how to compose the LoRa Uplink Payload by these RETURNs. The command is **AT+DATAUP.**

498

499

500

**Examples: AT+DATAUP=0**

501

502

Compose the uplink payload with value returns in sequence and send with **A SIGNLE UPLINK**.

Final Payload is

Battery Info+PAYVER + VALID Value from RETURN1 + Valid Value from RETURN2 + … + RETURNx

507

508

Where PAYVER is defined by AT+PAYVER, below is an example screen shot.

509

510

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image019.png]]

**Examples: AT+DATAUP=1**

515

516

Compose the uplink payload with value returns in sequence and send with **Multiply UPLINKs**.

Final Payload is

Battery Info+PAYVER + PAYLOAD COUNT + PAYLOAD# + DATA

521

522

1. Battery Info (2 bytes): Battery voltage

523

1. PAYVER (1 byte): Defined by AT+PAYVER

524

1. PAYLOAD COUNT (1 byte): Total how many uplinks of this sampling.

525

1. PAYLOAD# (1 byte): Number of this uplink. (from 0,1,2,3…,to PAYLOAD COUNT)

526

1. DATA: Valid value: max 6 bytes(US915 version here, [[Notice*!>>path:#max_byte]]) for each uplink so each uplink <= 11 bytes. For the last uplink, DATA will might less than 6 bytes

527

528

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image020.png]]

529

530

531

So totally there will be 3 uplinks for this sampling, each uplink includes 6 bytes DATA

532

533

DATA1=RETURN1 Valid Value = 20 20 0a 33 90 41

534

535

DATA2=1^^st^^ ~~ 6^^th^^ byte of Valid value of RETURN10= 02 aa 05 81 0a 20

536

537

DATA3=7^^th^^ ~~ 11^^th^^ bytes of Valid value of RETURN10 = 20 20 20 2d 30

Below are the uplink payloads:

542

543

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image021.png]]

544

545

546

Notice: the Max bytes is according to the max support bytes in different Frequency Bands for lowest SF. As below:

547

548

~* For AU915/AS923 bands, if UplinkDwell time=0, max 51 bytes for each uplink ( so 51 -5 = 46 max valid date)

549

550

* For AU915/AS923 bands, if UplinkDwell time=1, max 11 bytes for each uplink ( so 11 -5 = 6 max valid date).

551

552

* For US915 band, max 11 bytes for each uplink ( so 11 -5 = 6 max valid date).

553

554

~* For all other bands: max 51 bytes for each uplink ( so 51 -5 = 46 max valid date).

1.

11.

111. Uplink on demand

561

562

Except uplink periodically, RS485-BL is able to uplink on demand. The server sends downlink command to RS485-BL and RS485 will uplink data base on the command.

563

564

Downlink control command:

565

566

[[0x08 command>>path:#downlink_08]]: Poll an uplink with current command set in RS485-BL.

567

568

[[0xA8 command>>path:#downlink_A8]]: Send a command to RS485-BL and uplink the output from sensors.

1.

11.

111. Uplink on Interrupt

575

576

Put the interrupt sensor between 3.3v_out and GPIO ext.[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image022.png]]

577

578

AT+INTMOD=0 Disable Interrupt

579

580

AT+INTMOD=1 Interrupt trigger by rising or falling edge.

581

582

AT+INTMOD=2 Interrupt trigger by falling edge. ( Default Value)

583

584

AT+INTMOD=3 Interrupt trigger by rising edge.

1.

11. Uplink Payload

|**Size(bytes)**|**2**|**1**|**Length depends on the return from the commands**

|Value|(((

Battery(mV)

&

Interrupt _Flag

)))|(((

PAYLOAD_VER

)))|If the valid payload is too long and exceed the maximum support payload length in server, server will show payload not provided in the LoRaWAN server.

602

603

Below is the decoder for the first 3 bytes. The rest bytes are dynamic depends on different RS485 sensors.

604

605

606

function Decoder(bytes, port) {

607

608

~/~/Payload Formats of RS485-BL Deceive

return {

~/~/Battery,units:V

BatV:((bytes[0]<<8 | bytes[1])&0x7fff)/1000,

~/~/GPIO_EXTI

EXTI_Trigger:(bytes[0] & 0x80)? "TRUE":"FALSE",

619

620

~/~/payload of version

Pay_ver:bytes[2],

};

}

TTN V3 uplink screen shot.

635

636

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image023.png]]

637

638

1.

639

11. Configure RS485-BL via AT or Downlink

640

641

User can configure RS485-BL via [[AT Commands >>path:#_Using_the_AT]]or LoRaWAN Downlink Commands

642

643

There are two kinds of Commands:

644

645

* **Common Commands**: They should be available for each sensor, such as: change uplink interval, reset device. For firmware v1.3, user can find what common commands it supports: http:~/~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands

646

647

* **Sensor Related Commands**: These commands are special designed for RS485-BL. User can see these commands below:

1.

11.

111. Common Commands:

652

653

They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.3, user can find what common commands it supports: [[http:~~/~~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands>>url:http://wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands]]

1.

11.

111. Sensor related commands:

659

660

==== Choose Device Type (RS485 or TTL) ====

661

662

RS485-BL can connect to either RS485 sensors or TTL sensor. User need to specify what type of sensor need to connect.

* AT Command

**AT+MOD=1** ~/~/ Set to support RS485-MODBUS type sensors. User can connect multiply RS485 , Modbus sensors to the A / B pins.

667

668

**AT+MOD=2** ~/~/ Set to support TTL Level sensors, User can connect one TTL Sensor to the TXD/RXD/GND pins.

* Downlink Payload

**0A aa** à same as AT+MOD=aa

==== [[RS485 Debug Command>>path:#downlink_A8]] (AT+CFGDEV) ====

678

679

This command is used to configure the RS485 or TTL sensors; they won’t be used during sampling.

* AT Command

AT+CFGDEV=xx xx xx xx xx xx xx xx xx xx xx xx,m

684

685

m: 0: no CRC; 1: add CRC-16/MODBUS in the end of this command.

* Downlink Payload

Format: A8 MM NN XX XX XX XX YY

Where:

* MM: 1: add CRC-16/MODBUS ; 0: no CRC

696

* NN: The length of RS485 command

697

* XX XX XX XX: RS485 command total NN bytes

698

* YY: How many bytes will be uplink from the return of this RS485 command, if YY=0, RS485-BL will execute the downlink command without uplink; if YY>0, RS485-BL will uplink total YY bytes from the output of this RS485 command

**Example 1:**

To connect a Modbus Alarm with below commands.

703

704

* The command to active alarm is: 0A 05 00 04 00 01 4C B0. Where 0A 05 00 04 00 01 is the Modbus command to read the register 00 40 where stored the DI status. The 4C B0 is the CRC-16/MODBUS which calculate manually.

705

706

* The command to deactivate alarm is: 0A 05 00 04 00 00 8D 70. Where 0A 05 00 04 00 00 is the Modbus command to read the register 00 40 where stored the DI status. The 8D 70 is the CRC-16/MODBUS which calculate manually.

707

708

So if user want to use downlink command to control to RS485 Alarm, he can use:

709

710

**A8 01 06 0A 05 00 04 00 01 00**: to activate the RS485 Alarm

711

712

**A8 01 06 0A 05 00 04 00 00 00**: to deactivate the RS485 Alarm

713

714

A8 is type code and 01 means add CRC-16/MODBUS at the end, the 3^^rd^^ byte is 06, means the next 6 bytes are the command to be sent to the RS485 network, the final byte 00 means this command don’t need to acquire output.

**Example 2:**

Check TTL Sensor return:

720

721

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image024.png]]

==== Set Payload version ====

727

728

This is the first byte of the uplink payload. RS485-BL can connect to different sensors. User can set the PAYVER field to tell server how to decode the current payload.

* AT Command:

AT+PAYVER: Set PAYVER field = 1

* Downlink Payload:

0xAE 01 à Set PAYVER field = 0x01

738

739

0xAE 0F à Set PAYVER field = 0x0F

740

741

742

==== Set RS485 Sampling Commands ====

743

744

AT+COMMANDx, AT+DATACUTx and AT+SEARCHx

745

746

These three commands are used to configure how the RS485-BL polling data from Modbus device. Detail of usage please see : [[polling RS485 device>>path:#polling_485]].

* AT Command:

AT+COMMANDx: Configure RS485 read command to sensor.

752

753

AT+DATACUTx: Configure how to handle return from RS485 devices.

754

755

AT+SEARCHx: Configure search command

* Downlink Payload:

0xAF downlink command can be used to set AT+COMMANDx or AT+DATACUTx.

761

762

Note: if user use AT+COMMANDx to add a new command, he also need to send AT+DATACUTx downlink.

763

764

Format: AF MM NN LL XX XX XX XX YY

Where:

* MM: the ATCOMMAND or AT+DATACUT to be set. Value from 01 ~~ 0F,

769

* NN: 0: no CRC; 1: add CRC-16/MODBUS ; 2: set the AT+DATACUT value.

770

* LL: The length of AT+COMMAND or AT+DATACUT command

771

* XX XX XX XX: AT+COMMAND or AT+DATACUT command

772

* YY: If YY=0, RS485-BL will execute the downlink command without uplink; if YY=1, RS485-BL will execute an uplink after got this command.

Example:

**AF 03 01 06 0A 05 00 04 00 01 00**: Same as AT+COMMAND3=0A 05 00 04 00 01,1

777

778

**AF 03 02 06 10 01 05 06 09 0A 00**: Same as AT+DATACUT3=**16**,**1**,**5+6+9+10**

779

780

**AF 03 02 06 0B 02 05 07 08 0A 00**: Same as AT+DATACUT3=**11**,**2**,**5~~7+8~~10**

781

782

783

0xAB downlink command can be used for set AT+SEARCHx

784

785

Example: **AB aa 01 03 xx xx xx** (03 here means there are total 3 bytes after 03) So

786

787

* AB aa 01 03 xx xx xx same as AT+SEARCHaa=1,xx xx xx

788

* AB aa 02 03 xx xx xx 02 yy yy(03 means there are 3 bytes after 03, they are xx xx xx;02 means there are 2 bytes after 02, they are yy yy) so the commands

789

790

**AB aa 02 03 xx xx xx 02 yy yy** same as **AT+SEARCHaa=2,xx xx xx+yy yy**

791

792

793

==== Fast command to handle MODBUS device ====

794

795

AT+MBFUN is valid since v1.3 firmware version. The command is for fast configure to read Modbus devices. It is only valid for the devices which follow the [[MODBUS-RTU protocol>>url:https://www.modbustools.com/modbus.html]].

796

797

This command is valid since v1.3 firmware version

798

799

800

AT+MBFUN has only two value:

801

802

* AT+MBFUN=1: Enable Modbus reading. And get response base on the MODBUS return

803

804

AT+MBFUN=1, device can auto read the Modbus function code: 01, 02, 03 or 04. AT+MBFUN has lower priority vs AT+DATACUT command. If AT+DATACUT command is configured, AT+MBFUN will be ignore.

805

806

* AT+MBFUN=0: Disable Modbus fast reading.

Example:

* AT+MBFUN=1 and AT+DATACUT1/AT+DATACUT2 are not configure (0,0,0).

811

* AT+COMMAND1= 01 03 00 10 00 08,1 ~-~-> read slave address 01 , function code 03, start address 00 01, quantity of registers 00 08.

812

* AT+COMMAND2= 01 02 00 40 00 10,1 ~-~-> read slave address 01 , function code 02, start address 00 40, quantity of inputs 00 10.

813

814

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image025.png]]

815

816

817

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image026.png]]

* Downlink Commands:

A9 aa -à Same as AT+MBFUN=aa

823

824

825

==== RS485 command timeout ====

826

827

Some Modbus device has slow action to send replies. This command is used to configure the RS485-BL to use longer time to wait for their action.

828

829

Default value: 0, range: 0 ~~ 5 seconds

* AT Command:

AT+CMDDLaa=hex(bb cc)

Example:

**AT+CMDDL1=1000** to send the open time to 1000ms

* Downlink Payload:

0x AA aa bb cc

Same as: AT+CMDDLaa=hex(bb cc)

Example:

0xAA 01 03 E8 à Same as **AT+CMDDL1=1000 ms**

850

851

852

==== [[Uplink>>path:#downlink_A8]] payload mode ====

853

854

Define to use one uplink or multiple uplinks for the sampling.

855

856

The use of this command please see: [[Compose Uplink payload>>path:#DataUP]]

* AT Command:

AT+DATAUP=0

AT+DATAUP=1

* Downlink Payload:

0xAD 00 à Same as AT+DATAUP=0

868

869

0xAD 01 à Same as AT+DATAUP=1

870

871

872

==== Manually trigger an Uplink ====

873

874

Ask device to send an uplink immediately.

* Downlink Payload:

0x08 FF, RS485-BL will immediately send an uplink.

879

880

881

==== Clear RS485 Command ====

882

883

The AT+COMMANDx and AT+DATACUTx settings are stored in special location, user can use below command to clear them.

* AT Command:

**AT+CMDEAR=mm,nn** mm: start position of erase ,nn: stop position of erase

889

890

Etc. AT+CMDEAR=1,10 means erase AT+COMMAND1/AT+DATACUT1 to AT+COMMAND10/AT+DATACUT10

891

892

Example screen shot after clear all RS485 commands.

The uplink screen shot is:

897

898

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image023.png]]

* Downlink Payload:

0x09 aa bb same as AT+CMDEAR=aa,bb

904

905

906

==== Set Serial Communication Parameters ====

907

908

Set the Rs485 serial communication parameters:

* AT Command:

Set Baud Rate:

AT+BAUDR=9600 ~/~/ Options: (1200,2400,4800,14400,19200,115200)

Set UART parity

AT+PARITY=0 ~/~/ Option: 0: no parity, 1: odd parity, 2: even parity

Set STOPBIT

AT+STOPBIT=0 ~/~/ Option: 0 for 1bit; 1 for 1.5 bit ; 2 for 2 bits

* Downlink Payload:

A7 01 aa bb: Same AT+BAUDR=hex(aa bb)*100

Example:

* A7 01 00 60 same as AT+BAUDR=9600

934

* A7 01 04 80 same as AT+BAUDR=115200

935

936

A7 02 aa: Same as AT+PARITY=aa (aa value: 00 , 01 or 02)

937

938

A7 03 aa: Same as AT+STOPBIT=aa (aa value: 00 , 01 or 02)

939

940

941

==== Control output power duration ====

942

943

User can set the output power duration before each sampling.

* AT Command:

Example:

AT+3V3T=1000 ~/~/ 3V3 output power will open 1s before each sampling.

950

951

AT+5VT=1000 ~/~/ +5V output power will open 1s before each sampling.

952

953

954

* LoRaWAN Downlink Command:

955

956

07 01 aa bb Same as AT+5VT=(aa bb)

957

958

07 02 aa bb Same as AT+3V3T=(aa bb)

1.

11. Buttons

|**Button**|**Feature**

967

|**RST**|Reboot RS485-BL

1.

11. +3V3 Output

RS485-BL has a Controllable +3V3 output, user can use this output to power external sensor.

973

974

The +3V3 output will be valid for every sampling. RS485-BL will enable +3V3 output before all sampling and disable the +3V3 after all sampling.

975

976

977

The +3V3 output time can be controlled by AT Command.

**AT+3V3T=1000**

Means set +3v3 valid time to have 1000ms. So, the real +3v3 output will actually have 1000ms + sampling time for other sensors.

982

983

984

By default, the AT+3V3T=0. This is a special case, means the +3V3 output is always on at any time

1.

11. +5V Output

RS485-BL has a Controllable +5V output, user can use this output to power external sensor.

991

992

The +5V output will be valid for every sampling. RS485-BL will enable +5V output before all sampling and disable the +5v after all sampling.

993

994

995

The 5V output time can be controlled by AT Command.

**AT+5VT=1000**

Means set 5V valid time to have 1000ms. So, the real 5V output will actually have 1000ms + sampling time for other sensors.

1000

1001

1002

By default, the AT+5VT=0. If the external sensor which require 5v and require more time to get stable state, user can use this command to increase the power ON duration for this sensor.

1.

11. LEDs

|**LEDs**|**Feature**

1011

|**LED1**|Blink when device transmit a packet.

1.

11. Switch Jumper

|**Switch Jumper**|**Feature**

1017

|**SW1**|(((

1018

ISP position: Upgrade firmware via UART

1019

1020

Flash position: Configure device, check running status.

1021

)))

1022

|**SW2**|(((

1023

5V position: set to compatible with 5v I/O.

1024

1025

3.3v position: set to compatible with 3.3v I/O.,

)))

+3.3V: is always ON

+5V: Only open before every sampling. The time is by default, it is AT+5VT=0. Max open time. 5000 ms.

1. Case Study

User can check this URL for some case studies.

1035

1036

[[http:~~/~~/wiki.dragino.com/index.php?title=APP_RS485_COMMUNICATE_WITH_SENSORS>>url:http://wiki.dragino.com/index.php?title=APP_RS485_COMMUNICATE_WITH_SENSORS]]

1. Use AT Command

11. Access AT Command

1043

1044

RS485-BL supports AT Command set. User can use a USB to TTL adapter plus the 3.5mm Program Cable to connect to RS485-BL to use AT command, as below.

1045

1046

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image027.png]]

1047

1048

1049

In PC, User needs to set **serial tool**(such as [[putty>>url:https://www.chiark.greenend.org.uk/~~sgtatham/putty/latest.html]], SecureCRT) baud rate to **9600** to access to access serial console of RS485-BL. The default password is 123456. Below is the output for reference:

1050

1051

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image028.png]]

More detail AT Command manual can be found at [[AT Command Manual>>path:#AT_COMMAND]]

1.

11. Common AT Command Sequence

1061

111. Multi-channel ABP mode (Use with SX1301/LG308)

1062

1063

If device has not joined network yet:

AT+FDR

AT+NJM=0

ATZ

If device already joined network:

AT+NJM=0

ATZ

1.

11.

111. Single-channel ABP mode (Use with LG01/LG02)

1081

1082

AT+FDR Reset Parameters to Factory Default, Keys Reserve

1083

1084

AT+NJM=0 Set to ABP mode

1085

1086

AT+ADR=0 Set the Adaptive Data Rate Off

1087

1088

AT+DR=5 Set Data Rate

1089

1090

AT+TDC=60000 Set transmit interval to 60 seconds

1091

1092

AT+CHS=868400000 Set transmit frequency to 868.4Mhz

1093

1094

AT+RX2FQ=868400000 Set RX2Frequency to 868.4Mhz (according to the result from server)

1095

1096

AT+RX2DR=5 Set RX2DR to match the downlink DR from server. see below

1097

1098

AT+DADDR=26 01 1A F1 Set Device Address to 26 01 1A F1, this ID can be found in the LoRa Server portal.

ATZ Reset MCU

**Note:**

1. Make sure the device is set to ABP mode in the IoT Server.

1105

1. Make sure the LG01/02 gateway RX frequency is exactly the same as AT+CHS setting.

1106

1. Make sure SF / bandwidth setting in LG01/LG02 match the settings of AT+DR. refer [[this link>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/&file=LoRaWAN%201.0.3%20Regional%20Parameters.xlsx]] to see what DR means.

1107

1. The command AT+RX2FQ and AT+RX2DR is to let downlink work. to set the correct parameters, user can check the actually downlink parameters to be used. As below. Which shows the RX2FQ should use 868400000 and RX2DR should be 5

1108

1109

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image029.png]]

1. FAQ

11. How to upgrade the image?

1114

1115

The RS485-BL LoRaWAN Controller is shipped with a 3.5mm cable, the cable is used to upload image to RS485-BL to:

1116

1117

* Support new features

1118

* For bug fix

1119

* Change LoRaWAN bands.

1120

1121

Below shows the hardware connection for how to upload an image to RS485-BL:

1122

1123

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image030.png]]

1124

1125

**Step1:** Download [[flash loader>>url:https://www.st.com/content/st_com/en/products/development-tools/software-development-tools/stm32-software-development-tools/stm32-programmers/flasher-stm32.html]].

1126

1127

**Step2**: Download the [[LT Image files>>url:http://www.dragino.com/downloads/index.php?dir=LT_LoRa_IO_Controller/LT33222-L/image/]].

1128

1129

**Step3: **Open flashloader; choose the correct COM port to update.

|(((

HOLD PRO then press the RST button, SYS will be ON, then click next

)))

|(((

Board detected

)))

|(((

)))

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image031.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image032.png]]

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image033.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image034.png]]

1149

1150

1151

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image035.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image036.png]]

1.

11. How to change the LoRa Frequency Bands/Region?

1156

1157

User can follow the introduction for [[how to upgrade image>>path:#upgrade_image]]. When download the images, choose the required image file for download.

1.

11. How many RS485-Slave can RS485-BL connects?

1163

1164

The RS485-BL can support max 32 RS485 devices. Each uplink command of RS485-BL can support max 16 different RS485 command. So RS485-BL can support max 16 RS485 devices pre-program in the device for uplink. For other devices no pre-program, user can use the [[downlink message (type code 0xA8) to poll their info>>path:#downlink_A8]].

1. Trouble Shooting

11. Downlink doesn’t work, how to solve it?

1171

1172

Please see this link for debug:

1173

1174

[[http:~~/~~/wiki.dragino.com/index.php?title=Main_Page#LoRaWAN_Communication_Debug>>url:http://wiki.dragino.com/index.php?title=Main_Page#LoRaWAN_Communication_Debug]]

1.

11. Why I can’t join TTN V3 in US915 /AU915 bands?

1180

1181

It might about the channels mapping. Please see for detail.

1182

1183

[[http:~~/~~/wiki.dragino.com/index.php?title=LoRaWAN_Communication_Debug#Notice_of_US915.2FCN470.2FAU915_Frequency_band>>url:http://wiki.dragino.com/index.php?title=LoRaWAN_Communication_Debug#Notice_of_US915.2FCN470.2FAU915_Frequency_band]]

1. Order Info

**Part Number: RS485-BL-XXX**

**XXX:**

* **EU433**: frequency bands EU433

1194

* **EU868**: frequency bands EU868

1195

* **KR920**: frequency bands KR920

1196

* **CN470**: frequency bands CN470

1197

* **AS923**: frequency bands AS923

1198

* **AU915**: frequency bands AU915

1199

* **US915**: frequency bands US915

1200

* **IN865**: frequency bands IN865

1201

* **RU864**: frequency bands RU864

1202

* **KZ865: **frequency bands KZ865

1. Packing Info

**Package Includes**:

1207

1208

* RS485-BL x 1

1209

* Stick Antenna for LoRa RF part x 1

1210

* Program cable x 1

1211

1212

**Dimension and weight**:

1213

1214

* Device Size: 13.5 x 7 x 3 cm

1215

* Device Weight: 105g

1216

* Package Size / pcs : 14.5 x 8 x 5 cm

1217

* Weight / pcs : 170g

1. Support

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

1222

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to

1223

1224

[[support@dragino.com>>url:file:///D:/市场资料/说明书/LoRa/LT系列/support@dragino.com]]

Wiki source code of RS485-BL – Waterproof RS485 to LoRaWAN Converter

Applications

Navigation