Last modified by Xiaoling on 2024/01/15 09:36
<
From version < 67.20 >
edited by Xiaoling
on 2023/05/31 14:12
To version < 67.24 >
edited by Xiaoling
on 2023/05/31 14:49
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -163,7 +163,7 @@
163 163  [[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143909447-639.png]]
164 164  
165 165  
166 -= 2. Configure CPL03-LB to connect to LoRaWAN network =
166 += 2. Configure SPH01-LB to connect to LoRaWAN network =
167 167  
168 168  == 2.1 How it works ==
169 169  
... ... @@ -258,7 +258,7 @@
258 258  === 2.3.1 Battery Info ===
259 259  
260 260  
261 -Check the battery voltage for LSPH01.
261 +Check the battery voltage for SPH01-LB.
262 262  
263 263  Ex1: 0x0B45 = 2885mV
264 264  
... ... @@ -304,7 +304,7 @@
304 304  === 2.3.5 Interrupt Pin ===
305 305  
306 306  
307 -This data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H3.2SetInterruptMode"]] for the hardware and software set up.
307 +This data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H3.3.2SetInterruptMode"]] for the hardware and software set up.
308 308  
309 309  
310 310  **Example:**
... ... @@ -352,7 +352,7 @@
352 352  == 2.4 Uplink Interval ==
353 353  
354 354  
355 -The LSPH01 by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link: [[Change Uplink Interval>>doc:Main.End Device AT Commands and Downlink Command.WebHome||anchor="H4.1ChangeUplinkInterval"]]
355 +The SPH01-LB by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link: [[Change Uplink Interval>>doc:Main.End Device AT Commands and Downlink Command.WebHome||anchor="H4.1ChangeUplinkInterval"]]
356 356  
357 357  
358 358  == 2.5 Datalog Feature ==
... ... @@ -364,7 +364,7 @@
364 364  === 2.5.1 Ways to get datalog via LoRaWAN ===
365 365  
366 366  
367 -Set PNACKMD=1, SPH01-LB will wait for ACK for every uplink, when there is no LoRaWAN network,CPL03-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
367 +Set PNACKMD=1, SPH01-LB will wait for ACK for every uplink, when there is no LoRaWAN network,SPH01-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
368 368  
369 369  * (((
370 370  a) SPH01-LB will do an ACK check for data records sending to make sure every data arrive server.
... ... @@ -400,7 +400,7 @@
400 400  
401 401  User need to set (% style="color:blue" %)**SYNCMOD=1**(%%) to enable sync time via MAC command.
402 402  
403 -Once CPL03-LB Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to CPL03-LB. If CPL03-LB fails to get the time from the server, CPL03-LB will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
403 +Once SPH01-LB Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to SPH01-LB. If SPH01-LB fails to get the time from the server, SPH01-LB will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
404 404  
405 405  (% style="color:red" %)**Note: LoRaWAN Server need to support LoRaWAN v1.0.3(MAC v1.0.3) or higher to support this MAC command feature, Chirpstack,TTN V3 v3 and loriot support but TTN V3 v2 doesn't support. If server doesn't support this command, it will through away uplink packet with this command, so user will lose the packet with time request for TTN V3 v2 if SYNCMOD=1.**
406 406  
... ... @@ -428,7 +428,7 @@
428 428  )))
429 429  
430 430  (((
431 -Uplink Internal =5s，means CPL03-LB will send one packet every 5s. range 5~~255s.
431 +Uplink Internal =5s，means SPH01-LB will send one packet every 5s. range 5~~255s.
432 432  )))
433 433  
434 434  
... ... @@ -439,7 +439,7 @@
439 439  
440 440  
441 441  (((
442 -If the LSPH01 has more than 7 days not use or just clean the pH probe. User should put the probe inside pure water for more than 24 hours for activation. If no put in water, user need to put inside soil for more than 24 hours to ensure the measurement accuracy. 
442 +If the SPH01-LB has more than 7 days not use or just clean the pH probe. User should put the probe inside pure water for more than 24 hours for activation. If no put in water, user need to put inside soil for more than 24 hours to ensure the measurement accuracy. 
443 443  )))
444 444  
445 445  
... ... @@ -609,10 +609,10 @@
609 609  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
610 610  
611 611  
612 -== 3.3 Commands special design for CPL03-LB ==
612 +== 3.3 Commands special design for SPH01-LB ==
613 613  
614 614  
615 -These commands only valid for CPL03-LB, as below:
615 +These commands only valid for SPH01-LB, as below:
616 616  
617 617  
618 618  === 3.3.1 Set Transmit Interval Time ===
... ... @@ -694,6 +694,9 @@
694 694  
695 695  * Example 2: Downlink Payload: 06000003  ~/~/  Set the interrupt mode to rising edge trigger
696 696  
697 +
698 +
699 +
697 697  === 3.3.3 Calibrate Sensor ===
698 698  
699 699  
... ... @@ -731,7 +731,7 @@
731 731  Always 0x02
732 732  )))
733 733  
734 -(% style="color:#037691" %)**Software Type**(%%): Always 0x03 for LSPH01
737 +(% style="color:#037691" %)**Software Type**(%%): Always 0x03 for SPH01-LB
735 735  
736 736  (% style="color:#037691" %)**Frequency Band**:
737 737  
... ... @@ -781,7 +781,7 @@
781 781  = 4. Battery & Power Consumption =
782 782  
783 783  
784 -CPL03-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
787 +SPH01-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
785 785  
786 786  [[**Battery Info & Power Consumption Analyze**>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
787 787  
... ... @@ -790,7 +790,7 @@
790 790  
791 791  
792 792  (% class="wikigeneratedid" %)
793 -User can change firmware CPL03-LB to:
796 +User can change firmware SPH01-LB to:
794 794  
795 795  * Change Frequency band/ region.
796 796  
... ... @@ -817,7 +817,7 @@
817 817  = 7. Order Info =
818 818  
819 819  
820 -Part Number: (% style="color:blue" %)**CPL03-LB-XXX**
823 +Part Number: (% style="color:blue" %)**SPH01-LB-XXX**
821 821  
822 822  (% style="color:red" %)**XXX**(%%): The default frequency band
823 823  
... ... @@ -837,12 +837,16 @@
837 837  
838 838  * (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
839 839  
843 +
844 +
845 +
846 +
840 840  = 8. ​Packing Info =
841 841  
842 842  
843 843  (% style="color:#037691" %)**Package Includes**:
844 844  
845 -* CPL03-LB LoRaWAN Pulse/Contact Sensor
852 +* SPH01-LB LoRaWAN Soil Ph Sensor x 1
846 846  
847 847  (% style="color:#037691" %)**Dimension and weight**:
848 848  
... ... @@ -854,6 +854,10 @@
854 854  
855 855  * Weight / pcs : g
856 856  
864 +
865 +
866 +
867 +
857 857  = 9. Support =
858 858  
859 859  

Applications

Navigation

Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0