Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -163,7 +163,7 @@
163	163	[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143909447-639.png]]
164	164
165	165
166		-= 2. Configure CPL03-LB to connect to LoRaWAN network =
	166	+= 2. Configure SPH01-LB to connect to LoRaWAN network =
167	167
168	168	== 2.1 How it works ==
169	169
...	...	@@ -304,7 +304,7 @@
304	304	=== 2.3.5 Interrupt Pin ===
305	305
306	306
307		-This data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H3.2SetInterruptMode"]] for the hardware and software set up.
	307	+This data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H3.3.2SetInterruptMode"]] for the hardware and software set up.
308	308
309	309
310	310	**Example:**
...	...	@@ -364,7 +364,7 @@
364	364	=== 2.5.1 Ways to get datalog via LoRaWAN ===
365	365
366	366
367		-Set PNACKMD=1, SPH01-LB will wait for ACK for every uplink, when there is no LoRaWAN network,CPL03-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
	367	+Set PNACKMD=1, SPH01-LB will wait for ACK for every uplink, when there is no LoRaWAN network,SPH01-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
368	368
369	369	* (((
370	370	a) SPH01-LB will do an ACK check for data records sending to make sure every data arrive server.
...	...	@@ -400,7 +400,7 @@
400	400
401	401	User need to set (% style="color:blue" %)**SYNCMOD=1**(%%) to enable sync time via MAC command.
402	402
403		-Once CPL03-LB Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to CPL03-LB. If CPL03-LB fails to get the time from the server, CPL03-LB will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
	403	+Once SPH01-LB Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to SPH01-LB. If SPH01-LB fails to get the time from the server, SPH01-LB will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
404	404
405	405	(% style="color:red" %)**Note: LoRaWAN Server need to support LoRaWAN v1.0.3(MAC v1.0.3) or higher to support this MAC command feature, Chirpstack,TTN V3 v3 and loriot support but TTN V3 v2 doesn't support. If server doesn't support this command, it will through away uplink packet with this command, so user will lose the packet with time request for TTN V3 v2 if SYNCMOD=1.**
406	406
...	...	@@ -428,7 +428,7 @@
428	428	)))
429	429
430	430	(((
431		-Uplink Internal =5s，means CPL03-LB will send one packet every 5s. range 5~~255s.
	431	+Uplink Internal =5s，means SPH01-LB will send one packet every 5s. range 5~~255s.
432	432	)))
433	433
434	434
...	...	@@ -609,10 +609,10 @@
609	609	[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
610	610
611	611
612		-== 3.3 Commands special design for CPL03-LB ==
	612	+== 3.3 Commands special design for SPH01-LB ==
613	613
614	614
615		-These commands only valid for CPL03-LB, as below:
	615	+These commands only valid for SPH01-LB, as below:
616	616
617	617
618	618	=== 3.3.1 Set Transmit Interval Time ===
...	...	@@ -694,6 +694,9 @@
694	694
695	695	* Example 2: Downlink Payload: 06000003  ~/~/  Set the interrupt mode to rising edge trigger
696	696
	697	+
	698	+
	699	+
697	697	=== 3.3.3 Calibrate Sensor ===
698	698
699	699
...	...	@@ -781,7 +781,7 @@
781	781	= 4. Battery & Power Consumption =
782	782
783	783
784		-CPL03-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
	787	+SPH01-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
785	785
786	786	[[**Battery Info & Power Consumption Analyze**>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
787	787
...	...	@@ -790,7 +790,7 @@
790	790
791	791
792	792	(% class="wikigeneratedid" %)
793		-User can change firmware CPL03-LB to:
	796	+User can change firmware SPH01-LB to:
794	794
795	795	* Change Frequency band/ region.
796	796
...	...	@@ -817,7 +817,7 @@
817	817	= 7. Order Info =
818	818
819	819
820		-Part Number: (% style="color:blue" %)**CPL03-LB-XXX**
	823	+Part Number: (% style="color:blue" %)**SPH01-LB-XXX**
821	821
822	822	(% style="color:red" %)**XXX**(%%): The default frequency band
823	823
...	...	@@ -842,7 +842,7 @@
842	842
843	843	(% style="color:#037691" %)**Package Includes**:
844	844
845		-* CPL03-LB LoRaWAN Pulse/Contact Sensor
	848	+* SPH01-LB LoRaWAN Soil Ph Sensor x 1
846	846
847	847	(% style="color:#037691" %)**Dimension and weight**:
848	848