Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -333,7 +333,7 @@
333	333	[[Humidity>>||anchor="HHumidity:"]]
334	334	)))
335	335
336		-==== (% style="color:#4472c4" %)**Battery:**(%%) ====
	336	+==== (% style="color:#4472c4" %)**Battery**(%%) ====
337	337
338	338	Sensor Battery Level.
339	339
...	...	@@ -343,7 +343,7 @@
343	343
344	344
345	345
346		-==== (% style="color:#4472c4" %)**Temperature:**(%%) ====
	346	+==== (% style="color:#4472c4" %)**Temperature**(%%) ====
347	347
348	348	**Example**:
349	349
...	...	@@ -354,13 +354,13 @@
354	354	（FF3F & 8000：Judge whether the highest bit is 1, when the highest bit is 1, it is negative）
355	355
356	356
357		-==== (% style="color:#4472c4" %)**Humidity:**(%%) ====
	357	+==== (% style="color:#4472c4" %)**Humidity**(%%) ====
358	358
359	359
360	360	Read:0x(0197)=412    Value:  412 / 10=41.2, So 41.2%
361	361
362	362
363		-==== (% style="color:#4472c4" %)**Alarm Flag& MOD:**(%%) ====
	363	+==== (% style="color:#4472c4" %)**Alarm Flag& MOD**(%%) ====
364	364
365	365
366	366	**Example:**
...	...	@@ -539,7 +539,7 @@
539	539
540	540	= 3. Configure S31x-LB =
541	541
542		-== 3.1 Configure Methods: ==
	542	+== 3.1 Configure Methods ==
543	543
544	544
545	545	S31x-LB supports below configure method:
...	...	@@ -605,7 +605,7 @@
605	605	Sensor will upload Device Status via FPORT=5. See payload section for detail.
606	606
607	607
608		-=== 3.3.3 Set Temperature Alarm Threshold: ===
	608	+=== 3.3.3 Set Temperature Alarm Threshold ===
609	609
610	610	* (% style="color:blue" %)**AT Command:**
611	611
...	...	@@ -626,7 +626,7 @@
626	626	(% style="color:red" %)**(note: 3^^rd^^ byte= 0x00 for low limit(not set), 4^^th^^ byte = 0x1E for high limit: 30)**
627	627
628	628
629		-=== 3.3.4 Set Humidity Alarm Threshold: ===
	629	+=== 3.3.4 Set Humidity Alarm Threshold ===
630	630
631	631	* (% style="color:blue" %)**AT Command:**
632	632
...	...	@@ -647,7 +647,7 @@
647	647	(% style="color:red" %)**(note: 3^^rd^^ byte= 0x46 for low limit (70%), 4^^th^^ byte = 0x00 for high limit (not set))**
648	648
649	649
650		-=== 3.3.5 Set Alarm Interval: ===
	650	+=== 3.3.5 Set Alarm Interval ===
651	651
652	652	The shortest time of two Alarm packet. (unit: min)
653	653
...	...	@@ -660,7 +660,7 @@
660	660	(% style="color:#037691" %)**0x(0D 00 1E)**(%%)     **~-~--> ** Set AT+ATDC=0x 00 1E = 30 minutes
661	661
662	662
663		-=== 3.3.6 Get Alarm settings: ===
	663	+=== 3.3.6 Get Alarm settings ===
664	664
665	665
666	666	Send a LoRaWAN downlink to ask device send Alarm settings.
...	...	@@ -676,7 +676,7 @@
676	676
677	677	* Alarm & MOD bit is 0x7C, 0x7C >> 2 = 0x31: Means this message is the Alarm settings message.
678	678
679		-=== 3.3.7 Set Interrupt Mode: ===
	679	+=== 3.3.7 Set Interrupt Mode ===
680	680
681	681
682	682	Feature, Set Interrupt mode for GPIO_EXIT.
...	...	@@ -707,7 +707,7 @@
707	707	* Example 1: Downlink Payload: 06000000  ~/~/  Turn off interrupt mode
708	708	* Example 2: Downlink Payload: 06000003  ~/~/  Set the interrupt mode to rising edge trigger
709	709
710		-= 4. Battery & Power Consumption: =
	710	+= 4. Battery & Power Consumption =
711	711
712	712
713	713	S31x-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
...	...	@@ -715,7 +715,7 @@
715	715	[[**Battery Info & Power Consumption Analyze**>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
716	716
717	717
718		-= 5. OTA Firmware update: =
	718	+= 5. OTA Firmware update =
719	719
720	720
721	721	(% class="wikigeneratedid" %)