Wiki source code of LSE01-LoRaWAN Soil Moisture & EC Sensor User Manual

Version 26.2 by Xiaoling on 2022/06/06 16:57

version	line-number	content
4.2	1	(% style="text-align:center" %)
	2	[[image:image-20220606151504-2.jpeg\|\|height="848" width="848"]]
1.1	3
	4
	5
	6
	7
	8
	9
	10
12.2	11	= 1. Introduction =
1.1	12
12.2	13	== 1.1 What is LoRaWAN Soil Moisture & EC Sensor ==
1.1	14
12.2	15	(((
	16	The Dragino LSE01 is a (% style="color:#4f81bd" %)LoRaWAN Soil Moisture & EC Sensor(%%) for IoT of Agriculture. It is designed to measure the soil moisture of saline-alkali soil and loamy soil. The soil sensor uses FDR method to calculate the soil moisture with the compensation from soil temperature and conductivity. It also has been calibrated in factory for Mineral soil type.
	17	)))
1.1	18
12.2	19	(((
	20	It detects (% style="color:#4f81bd" %)Soil Moisture(%%), (% style="color:#4f81bd" %)Soil Temperature(%%) and (% style="color:#4f81bd" %)Soil Conductivity(%%), and uploads the value via wireless to LoRaWAN IoT Server.
	21	)))
1.1	22
12.2	23	(((
4.2	24	The LoRa wireless technology used in LES01 allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
12.2	25	)))
4.2	26
12.2	27	(((
	28	LES01 is powered by (% style="color:#4f81bd" %)4000mA or 8500mAh Li-SOCI2 battery(%%), It is designed for long term use up to 10 years.
	29	)))
4.2	30
12.2	31	(((
4.2	32	Each LES01 is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
12.2	33	)))
4.2	34
	35
12.2	36	[[image:1654503236291-817.png]]
4.2	37
	38
13.2	39	[[image:1654503265560-120.png]]
4.2	40
	41
	42
13.3	43	== 1.2 Features ==
	44
4.2	45	* LoRaWAN 1.0.3 Class A
	46	* Ultra low power consumption
	47	* Monitor Soil Moisture
	48	* Monitor Soil Temperature
	49	* Monitor Soil Conductivity
	50	* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
	51	* AT Commands to change parameters
	52	* Uplink on periodically
	53	* Downlink to change configure
	54	* IP66 Waterproof Enclosure
	55	* 4000mAh or 8500mAh Battery for long term use
	56
13.3	57	== 1.3 Specification ==
	58
4.2	59	Measure Volume: Base on the centra pin of the probe, a cylinder with 7cm diameter and 10cm height.
	60
14.2	61	[[image:image-20220606162220-5.png]]
	62
4.2	63
	64
14.3	65	== 1.4 Applications ==
4.2	66
	67	* Smart Agriculture
	68
15.6	69	(% class="wikigeneratedid" id="H200B1.5FirmwareChangelog" %)
	70
4.2	71
15.6	72	== 1.5 Firmware Change log ==
	73
	74
14.3	75	LSE01 v1.0 : Release
4.2	76
14.3	77
	78
	79	= 2. Configure LSE01 to connect to LoRaWAN network =
	80
	81	== 2.1 How it works ==
	82
15.3	83	(((
4.2	84	The LSE01 is configured as LoRaWAN OTAA Class A mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and power on the LSE0150. It will automatically join the network via OTAA and start to send the sensor value
15.3	85	)))
4.2	86
15.3	87	(((
15.4	88	In case you can’t set the OTAA keys in the LoRaWAN OTAA server, and you have to use the keys from the server, you can [[use AT Commands >>\|\|anchor="H3.UsingtheATCommands"]].
15.3	89	)))
4.2	90
	91
	92
14.4	93	== 2.2 Quick guide to connect to LoRaWAN server (OTAA) ==
4.2	94
	95	Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LG308>>url:http://www.dragino.com/products/lora/item/140-lg308.html]] as a LoRaWAN gateway in this example.
	96
	97
15.2	98	[[image:1654503992078-669.png]]
4.2	99
	100
	101	The LG308 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
	102
	103
	104	Step 1: Create a device in TTN with the OTAA keys from LSE01.
	105
	106	Each LSE01 is shipped with a sticker with the default device EUI as below:
	107
17.2	108	[[image:image-20220606163732-6.jpeg]]
4.2	109
	110	You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:
	111
	112	Add APP EUI in the application
	113
	114
17.2	115	[[image:1654504596150-405.png]]
4.2	116
	117
	118
	119	Add APP KEY and DEV EUI
	120
18.2	121	[[image:1654504683289-357.png]]
4.2	122
	123
19.2	124
4.2	125	Step 2: Power on LSE01
	126
	127
	128	Put a Jumper on JP2 to power on the device. ( The Jumper must be in FLASH position).
	129
19.2	130	[[image:image-20220606163915-7.png]]
4.2	131
	132
	133	Step 3: The LSE01 will auto join to the TTN network. After join success, it will start to upload messages to TTN and you can see the messages in the panel.
	134
20.2	135	[[image:1654504778294-788.png]]
4.2	136
	137
	138
20.3	139	== 2.3 Uplink Payload ==
4.2	140
20.3	141	=== 2.3.1 MOD~=0(Default Mode) ===
4.2	142
4.4	143	LSE01 will uplink payload via LoRaWAN with below payload format:
4.2	144
	145
	146	Uplink payload includes in total 11 bytes.
	147
	148
	149	\|(((
	150	Size
	151
	152	(bytes)
	153	)))\|2\|2\|2\|2\|2\|1
	154	\|Value\|[[BAT>>path:#bat]]\|(((
	155	Temperature
	156
	157	(Reserve, Ignore now)
	158	)))\|[[Soil Moisture>>path:#soil_moisture]]\|[[Soil Temperature>>path:#soil_tem]]\|[[Soil Conductivity (EC)>>path:#EC]]\|(((
	159	MOD & Digital Interrupt
	160
	161	(Optional)
	162	)))
	163
22.2	164	[[image:1654504881641-514.png]]
4.2	165
	166
	167
22.2	168	=== 2.3.2 MOD~=1(Original value) ===
	169
4.2	170	This mode can get the original AD value of moisture and original conductivity (with temperature drift compensation).
	171
	172	\|(((
	173	Size
	174
	175	(bytes)
	176	)))\|2\|2\|2\|2\|2\|1
	177	\|Value\|[[BAT>>path:#bat]]\|(((
	178	Temperature
	179
	180	(Reserve, Ignore now)
	181	)))\|[[Soil Moisture>>path:#soil_moisture]](raw)\|[[Soil Temperature>>path:#soil_tem]]\|[[Soil Conductivity (EC)>>path:#EC]](raw)\|(((
	182	MOD & Digital Interrupt
	183
	184	(Optional)
	185	)))
	186
22.2	187	[[image:1654504907647-967.png]]
4.2	188
	189
22.2	190
	191	=== 2.3.3 Battery Info ===
	192
4.2	193	Check the battery voltage for LSE01.
	194
	195	Ex1: 0x0B45 = 2885mV
	196
	197	Ex2: 0x0B49 = 2889mV
	198
	199
	200
22.3	201	=== 2.3.4 Soil Moisture ===
4.2	202
	203	Get the moisture content of the soil. The value range of the register is 0-10000(Decimal), divide this value by 100 to get the percentage of moisture in the soil.
	204
22.4	205	For example, if the data you get from the register is __0x05 0xDC__, the moisture content in the soil is
4.2	206
	207
22.4	208	(% style="color:#4f81bd" %)05DC(H) = 1500(D) /100 = 15%.
4.2	209
22.4	210
4.2	211
22.5	212	=== 2.3.5 Soil Temperature ===
	213
4.2	214	Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is 0x09 0xEC, the temperature content in the soil is
	215
	216	Example:
	217
	218	If payload is 0105H: ((0x0105 & 0x8000)>>15 === 0),temp = 0105(H)/100 = 2.61 °C
	219
	220	If payload is FF7EH: ((FF7E & 0x8000)>>15 ===1),temp = (FF7E(H)-FFFF(H))/100 = -1.29 °C
	221
	222
	223
22.6	224	=== 2.3.6 Soil Conductivity (EC) ===
	225
23.2	226	(((
	227	Obtain (% style="color:#4f81bd" %)__soluble salt concentration__(%%) in soil or (% style="color:#4f81bd" %)__soluble ion concentration in liquid fertilizer__(%%) or (% style="color:#4f81bd" %)__planting medium__(%%). The value range of the register is 0 - 20000(Decimal)( Can be greater than 20000).
	228	)))
4.2	229
23.2	230	(((
4.2	231	For example, if the data you get from the register is 0x00 0xC8, the soil conductivity is 00C8(H) = 200(D) = 200 uS/cm.
23.2	232	)))
4.2	233
23.2	234	(((
4.2	235	Generally, the EC value of irrigation water is less than 800uS / cm.
23.2	236	)))
4.2	237
23.2	238	(((
	239
	240	)))
4.2	241
23.2	242	(((
	243
	244	)))
	245
	246	=== 2.3.7 MOD ===
	247
4.2	248	Firmware version at least v2.1 supports changing mode.
	249
	250	For example, bytes[10]=90
	251
	252	mod=(bytes[10]>>7)&0x01=1.
	253
	254
	255	Downlink Command:
	256
	257	If payload = 0x0A00, workmode=0
	258
	259	If payload = 0x0A01, workmode=1
	260
	261
	262
23.2	263	=== 2.3.8 Decode payload in The Things Network ===
	264
4.2	265	While using TTN network, you can add the payload format to decode the payload.
	266
	267
23.2	268	[[image:1654505570700-128.png]]
4.2	269
	270	The payload decoder function for TTN is here:
	271
	272	LSE01 TTN Payload Decoder: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Payload_Decoder/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Payload_Decoder/]]
	273
	274
23.3	275	== 2.4 Uplink Interval ==
4.2	276
	277	The LSE01 by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link:
	278
	279	[[http:~~/~~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands#Change_Uplink_Interval>>url:http://wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands#Change_Uplink_Interval]]
	280
	281
24.2	282
	283	== 2.5 Downlink Payload ==
	284
4.2	285	By default, LSE50 prints the downlink payload to console port.
	286
24.2	287	[[image:image-20220606165544-8.png]]
4.2	288
24.2	289
26.2	290	Examples:
4.2	291
	292
26.2	293	* Set TDC
4.2	294
	295	If the payload=0100003C, it means set the END Node’s TDC to 0x00003C=60(S), while type code is 01.
	296
	297	Payload: 01 00 00 1E TDC=30S
	298
	299	Payload: 01 00 00 3C TDC=60S
	300
	301
26.2	302	* Reset
4.2	303
	304	If payload = 0x04FF, it will reset the LSE01
	305
	306
26.2	307	* CFM
4.2	308
	309	Downlink Payload: 05000001, Set AT+CFM=1 or 05000000 , set AT+CFM=0
	310
	311
26.2	312
	313	== 2.6 Show Data in DataCake IoT Server ==
	314
4.2	315	[[DATACAKE>>url:https://datacake.co/]] provides a human friendly interface to show the sensor data, once we have data in TTN, we can use [[DATACAKE>>url:https://datacake.co/]] to connect to TTN and see the data in DATACAKE. Below are the steps:
	316
	317
	318	Step 1: Be sure that your device is programmed and properly connected to the network at this time.
	319
	320	Step 2: To configure the Application to forward data to DATACAKE you will need to add integration. To add the DATACAKE integration, perform the following steps:
	321
	322
26.2	323	[[image:1654505857935-743.png]]
4.2	324
	325
26.2	326	[[image:1654505874829-548.png]]
4.2	327
	328
	329
	330
	331
	332	Step 3: Create an account or log in Datacake.
	333
	334	Step 4: Search the LSE01 and add DevEUI.
	335
	336
	337	[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image012.png]]
	338
	339
	340
	341	After added, the sensor data arrive TTN, it will also arrive and show in Mydevices.
	342
	343
	344	[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image013.png]]
	345
	346
	347
4.4	348	1.
4.2	349	11. Frequency Plans
	350
	351	The LSE01 uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
	352
23.2	353	1.
	354	11.
4.2	355	111. EU863-870 (EU868)
	356
	357	Uplink:
	358
	359	868.1 - SF7BW125 to SF12BW125
	360
	361	868.3 - SF7BW125 to SF12BW125 and SF7BW250
	362
	363	868.5 - SF7BW125 to SF12BW125
	364
	365	867.1 - SF7BW125 to SF12BW125
	366
	367	867.3 - SF7BW125 to SF12BW125
	368
	369	867.5 - SF7BW125 to SF12BW125
	370
	371	867.7 - SF7BW125 to SF12BW125
	372
	373	867.9 - SF7BW125 to SF12BW125
	374
	375	868.8 - FSK
	376
	377
	378	Downlink:
	379
	380	Uplink channels 1-9 (RX1)
	381
	382	869.525 - SF9BW125 (RX2 downlink only)
	383
	384
23.2	385	1.
	386	11.
4.2	387	111. US902-928(US915)
	388
	389	Used in USA, Canada and South America. Default use CHE=2
	390
	391	Uplink:
	392
	393	903.9 - SF7BW125 to SF10BW125
	394
	395	904.1 - SF7BW125 to SF10BW125
	396
	397	904.3 - SF7BW125 to SF10BW125
	398
	399	904.5 - SF7BW125 to SF10BW125
	400
	401	904.7 - SF7BW125 to SF10BW125
	402
	403	904.9 - SF7BW125 to SF10BW125
	404
	405	905.1 - SF7BW125 to SF10BW125
	406
	407	905.3 - SF7BW125 to SF10BW125
	408
	409
	410	Downlink:
	411
	412	923.3 - SF7BW500 to SF12BW500
	413
	414	923.9 - SF7BW500 to SF12BW500
	415
	416	924.5 - SF7BW500 to SF12BW500
	417
	418	925.1 - SF7BW500 to SF12BW500
	419
	420	925.7 - SF7BW500 to SF12BW500
	421
	422	926.3 - SF7BW500 to SF12BW500
	423
	424	926.9 - SF7BW500 to SF12BW500
	425
	426	927.5 - SF7BW500 to SF12BW500
	427
	428	923.3 - SF12BW500(RX2 downlink only)
	429
	430
23.2	431	1.
	432	11.
4.2	433	111. CN470-510 (CN470)
	434
	435	Used in China, Default use CHE=1
	436
	437	Uplink:
	438
	439	486.3 - SF7BW125 to SF12BW125
	440
	441	486.5 - SF7BW125 to SF12BW125
	442
	443	486.7 - SF7BW125 to SF12BW125
	444
	445	486.9 - SF7BW125 to SF12BW125
	446
	447	487.1 - SF7BW125 to SF12BW125
	448
	449	487.3 - SF7BW125 to SF12BW125
	450
	451	487.5 - SF7BW125 to SF12BW125
	452
	453	487.7 - SF7BW125 to SF12BW125
	454
	455
	456	Downlink:
	457
	458	506.7 - SF7BW125 to SF12BW125
	459
	460	506.9 - SF7BW125 to SF12BW125
	461
	462	507.1 - SF7BW125 to SF12BW125
	463
	464	507.3 - SF7BW125 to SF12BW125
	465
	466	507.5 - SF7BW125 to SF12BW125
	467
	468	507.7 - SF7BW125 to SF12BW125
	469
	470	507.9 - SF7BW125 to SF12BW125
	471
	472	508.1 - SF7BW125 to SF12BW125
	473
	474	505.3 - SF12BW125 (RX2 downlink only)
	475
	476
23.2	477	1.
	478	11.
4.2	479	111. AU915-928(AU915)
	480
	481	Default use CHE=2
	482
	483	Uplink:
	484
	485	916.8 - SF7BW125 to SF12BW125
	486
	487	917.0 - SF7BW125 to SF12BW125
	488
	489	917.2 - SF7BW125 to SF12BW125
	490
	491	917.4 - SF7BW125 to SF12BW125
	492
	493	917.6 - SF7BW125 to SF12BW125
	494
	495	917.8 - SF7BW125 to SF12BW125
	496
	497	918.0 - SF7BW125 to SF12BW125
	498
	499	918.2 - SF7BW125 to SF12BW125
	500
	501
	502	Downlink:
	503
	504	923.3 - SF7BW500 to SF12BW500
	505
	506	923.9 - SF7BW500 to SF12BW500
	507
	508	924.5 - SF7BW500 to SF12BW500
	509
	510	925.1 - SF7BW500 to SF12BW500
	511
	512	925.7 - SF7BW500 to SF12BW500
	513
	514	926.3 - SF7BW500 to SF12BW500
	515
	516	926.9 - SF7BW500 to SF12BW500
	517
	518	927.5 - SF7BW500 to SF12BW500
	519
	520	923.3 - SF12BW500(RX2 downlink only)
	521
23.2	522	1.
	523	11.
4.2	524	111. AS920-923 & AS923-925 (AS923)
	525
	526	Default Uplink channel:
	527
	528	923.2 - SF7BW125 to SF10BW125
	529
	530	923.4 - SF7BW125 to SF10BW125
	531
	532
	533	Additional Uplink Channel:
	534
	535	(OTAA mode, channel added by JoinAccept message)
	536
	537	AS920~~AS923 for Japan, Malaysia, Singapore:
	538
	539	922.2 - SF7BW125 to SF10BW125
	540
	541	922.4 - SF7BW125 to SF10BW125
	542
	543	922.6 - SF7BW125 to SF10BW125
	544
	545	922.8 - SF7BW125 to SF10BW125
	546
	547	923.0 - SF7BW125 to SF10BW125
	548
	549	922.0 - SF7BW125 to SF10BW125
	550
	551
	552	AS923 ~~ AS925 for Brunei, Cambodia, Hong Kong, Indonesia, Laos, Taiwan, Thailand, Vietnam:
	553
	554	923.6 - SF7BW125 to SF10BW125
	555
	556	923.8 - SF7BW125 to SF10BW125
	557
	558	924.0 - SF7BW125 to SF10BW125
	559
	560	924.2 - SF7BW125 to SF10BW125
	561
	562	924.4 - SF7BW125 to SF10BW125
	563
	564	924.6 - SF7BW125 to SF10BW125
	565
	566
	567
	568	Downlink:
	569
	570	Uplink channels 1-8 (RX1)
	571
	572	923.2 - SF10BW125 (RX2)
	573
	574
23.2	575	1.
	576	11.
4.2	577	111. KR920-923 (KR920)
	578
	579	Default channel:
	580
	581	922.1 - SF7BW125 to SF12BW125
	582
	583	922.3 - SF7BW125 to SF12BW125
	584
	585	922.5 - SF7BW125 to SF12BW125
	586
	587
	588	Uplink: (OTAA mode, channel added by JoinAccept message)
	589
	590	922.1 - SF7BW125 to SF12BW125
	591
	592	922.3 - SF7BW125 to SF12BW125
	593
	594	922.5 - SF7BW125 to SF12BW125
	595
	596	922.7 - SF7BW125 to SF12BW125
	597
	598	922.9 - SF7BW125 to SF12BW125
	599
	600	923.1 - SF7BW125 to SF12BW125
	601
	602	923.3 - SF7BW125 to SF12BW125
	603
	604
	605	Downlink:
	606
	607	Uplink channels 1-7(RX1)
	608
	609	921.9 - SF12BW125 (RX2 downlink only; SF12BW125 might be changed to SF9BW125)
	610
	611
23.2	612	1.
	613	11.
4.2	614	111. IN865-867 (IN865)
	615
	616	Uplink:
	617
	618	865.0625 - SF7BW125 to SF12BW125
	619
	620	865.4025 - SF7BW125 to SF12BW125
	621
	622	865.9850 - SF7BW125 to SF12BW125
	623
	624
	625	Downlink:
	626
	627	Uplink channels 1-3 (RX1)
	628
	629	866.550 - SF10BW125 (RX2)
	630
	631
23.2	632	1.
4.2	633	11. LED Indicator
	634
	635	The LSE01 has an internal LED which is to show the status of different state.
	636
	637
	638	* Blink once when device power on.
	639	* Solid ON for 5 seconds once device successful Join the network.
	640	* Blink once when device transmit a packet.
	641
23.2	642	1.
4.2	643	11. Installation in Soil
	644
	645	Measurement the soil surface
	646
	647
	648	[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image014.png]]
	649
	650	Choose the proper measuring position. Avoid the probe to touch rocks or hard things. Split the surface soil according to the measured deep. Keep the measured as original density. Vertical insert the probe into the soil to be measured. Make sure not shake when inserting.
	651
	652
	653
	654
	655
	656
	657
	658	[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image015.png]]
	659
	660
	661
	662	Dig a hole with diameter > 20CM.
	663
	664	Horizontal insert the probe to the soil and fill the hole for long term measurement.
	665
	666
	667
	668
23.2	669	1.
4.2	670	11. Firmware Change Log
	671
	672	Firmware download link:
	673
	674	[[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/]]
	675
	676
	677	Firmware Upgrade Method:
	678
	679	[[http:~~/~~/wiki.dragino.com/index.php?title=Firmware_Upgrade_Instruction_for_STM32_base_products#Introduction>>url:http://wiki.dragino.com/index.php?title=Firmware_Upgrade_Instruction_for_STM32_base_products#Introduction]]
	680
	681
	682	V1.0.
	683
	684	Release
	685
	686
	687
23.2	688	1.
4.2	689	11. Battery Analysis
	690	111. Battery Type
	691
	692	The LSE01 battery is a combination of a 4000mAh Li/SOCI2 Battery and a Super Capacitor. The battery is non-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
	693
	694
	695	The battery is designed to last for more than 5 years for the LSN50.
	696
	697
	698	The battery related documents as below:
	699
	700	* [[Battery Dimension>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/&file=LSN50-Battery-Dimension.pdf]],
	701	* [[Lithium-Thionyl Chloride Battery>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/ER18505_datasheet-EN.pdf]] datasheet, [[Tech Spec>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/ER18505_datasheet_PM-ER18505-S-02-LF_EN.pdf]]
	702	* [[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC_1520_datasheet.jpg]], [[Tech Spec>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC1520%20Technical%20Specification20171123.pdf]]
	703
	704	\|(((
	705	JST-XH-2P connector
	706	)))
	707
	708	[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image016.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image017.png]]
	709
	710
	711
23.2	712	1.
	713	11.
4.2	714	111. Battery Note
	715
	716	The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
	717
	718
23.2	719	1.
	720	11.
4.2	721	111. Replace the battery
	722
	723	If Battery is lower than 2.7v, user should replace the battery of LSE01.
	724
	725
	726	You can change the battery in the LSE01.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.
	727
	728
	729	The default battery pack of LSE01 includes a ER18505 plus super capacitor. If user can’t find this pack locally, they can find ER18505 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
	730
	731
	732
	733
	734
	735
9.2	736	= 3. Using the AT Commands =
4.2	737
9.2	738	== 3.1 Access AT Commands ==
	739
11.4	740
4.2	741	LSE01 supports AT Command set in the stock firmware. You can use a USB to TTL adapter to connect to LSE01 for using AT command, as below.
	742
9.2	743	[[image:1654501986557-872.png]]
4.2	744
	745
	746	Or if you have below board, use below connection:
	747
	748
11.2	749	[[image:1654502005655-729.png]]
4.2	750
	751
	752
11.2	753	In the PC, you need to set the serial baud rate to (% style="color:green" %)9600(%%) to access the serial console for LSE01. LSE01 will output system info once power on as below:
4.2	754
	755
11.2	756	[[image:1654502050864-459.png]]
4.2	757
	758
	759	Below are the available commands, a more detailed AT Command manual can be found at [[AT Command Manual>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/]]: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/]]
	760
	761
11.4	762	(% style="background-color:#dcdcdc" %)AT+<CMD>=?AT+<CMD>? (%%) : Help on <CMD>
4.2	763
11.4	764	(% style="background-color:#dcdcdc" %)AT+<CMD>=?AT+<CMD> (%%) : Run <CMD>
4.2	765
11.4	766	(% style="background-color:#dcdcdc" %)AT+<CMD>=?AT+<CMD>=<value>(%%) : Set the value
4.2	767
11.4	768	(% style="background-color:#dcdcdc" %)AT+<CMD>=?AT+<CMD>=?(%%) : Get the value
4.2	769
	770
11.6	771	(% style="color:#037691" %)General Commands(%%)
4.2	772
11.6	773	(% style="background-color:#dcdcdc" %)AT(%%) : Attention
4.2	774
11.6	775	(% style="background-color:#dcdcdc" %)AT?(%%) : Short Help
4.2	776
11.6	777	(% style="background-color:#dcdcdc" %)ATZ(%%) : MCU Reset
4.2	778
11.6	779	(% style="background-color:#dcdcdc" %)AT+TDC(%%) : Application Data Transmission Interval
4.2	780
	781
11.4	782	(% style="color:#037691" %)Keys, IDs and EUIs management
4.2	783
11.6	784	(% style="background-color:#dcdcdc" %)AT+APPEUI(%%) : Application EUI
4.2	785
11.6	786	(% style="background-color:#dcdcdc" %)AT+APPKEY(%%) : Application Key
4.2	787
11.6	788	(% style="background-color:#dcdcdc" %)AT+APPSKEY(%%) : Application Session Key
4.2	789
11.6	790	(% style="background-color:#dcdcdc" %)AT+DADDR(%%) : Device Address
4.2	791
11.6	792	(% style="background-color:#dcdcdc" %)AT+DEUI(%%) : Device EUI
4.2	793
11.6	794	(% style="background-color:#dcdcdc" %)AT+NWKID(%%) : Network ID (You can enter this command change only after successful network connection)
4.2	795
11.6	796	(% style="background-color:#dcdcdc" %)AT+NWKSKEY(%%) : Network Session Key Joining and sending date on LoRa network
4.2	797
11.6	798	(% style="background-color:#dcdcdc" %)AT+CFM(%%) : Confirm Mode
4.2	799
11.6	800	(% style="background-color:#dcdcdc" %)AT+CFS(%%) : Confirm Status
4.2	801
11.6	802	(% style="background-color:#dcdcdc" %)AT+JOIN(%%) : Join LoRa? Network
4.2	803
11.6	804	(% style="background-color:#dcdcdc" %)AT+NJM(%%) : LoRa? Network Join Mode
4.2	805
11.6	806	(% style="background-color:#dcdcdc" %)AT+NJS(%%) : LoRa? Network Join Status
4.2	807
11.6	808	(% style="background-color:#dcdcdc" %)AT+RECV(%%) : Print Last Received Data in Raw Format
4.2	809
11.6	810	(% style="background-color:#dcdcdc" %)AT+RECVB(%%) : Print Last Received Data in Binary Format
4.2	811
11.6	812	(% style="background-color:#dcdcdc" %)AT+SEND(%%) : Send Text Data
4.2	813
11.6	814	(% style="background-color:#dcdcdc" %)AT+SENB(%%) : Send Hexadecimal Data
4.2	815
	816
11.4	817	(% style="color:#037691" %)LoRa Network Management
4.2	818
11.6	819	(% style="background-color:#dcdcdc" %)AT+ADR(%%) : Adaptive Rate
4.2	820
11.6	821	(% style="background-color:#dcdcdc" %)AT+CLASS(%%) : LoRa Class(Currently only support class A
4.2	822
11.6	823	(% style="background-color:#dcdcdc" %)AT+DCS(%%) : Duty Cycle Setting
4.2	824
11.6	825	(% style="background-color:#dcdcdc" %)AT+DR(%%) : Data Rate (Can Only be Modified after ADR=0)
4.2	826
11.6	827	(% style="background-color:#dcdcdc" %)AT+FCD(%%) : Frame Counter Downlink
4.2	828
11.6	829	(% style="background-color:#dcdcdc" %)AT+FCU(%%) : Frame Counter Uplink
4.2	830
11.6	831	(% style="background-color:#dcdcdc" %)AT+JN1DL(%%) : Join Accept Delay1
4.2	832
11.6	833	(% style="background-color:#dcdcdc" %)AT+JN2DL(%%) : Join Accept Delay2
4.2	834
11.6	835	(% style="background-color:#dcdcdc" %)AT+PNM(%%) : Public Network Mode
4.2	836
11.6	837	(% style="background-color:#dcdcdc" %)AT+RX1DL(%%) : Receive Delay1
4.2	838
11.6	839	(% style="background-color:#dcdcdc" %)AT+RX2DL(%%) : Receive Delay2
4.2	840
11.6	841	(% style="background-color:#dcdcdc" %)AT+RX2DR(%%) : Rx2 Window Data Rate
4.2	842
11.6	843	(% style="background-color:#dcdcdc" %)AT+RX2FQ(%%) : Rx2 Window Frequency
4.2	844
11.6	845	(% style="background-color:#dcdcdc" %)AT+TXP(%%) : Transmit Power
4.2	846
11.6	847	(% style="background-color:#dcdcdc" %)AT+ MOD(%%) : Set work mode
4.2	848
	849
11.4	850	(% style="color:#037691" %)Information
4.2	851
11.6	852	(% style="background-color:#dcdcdc" %)AT+RSSI(%%) : RSSI of the Last Received Packet
4.2	853
11.6	854	(% style="background-color:#dcdcdc" %)AT+SNR(%%) : SNR of the Last Received Packet
4.2	855
11.6	856	(% style="background-color:#dcdcdc" %)AT+VER(%%) : Image Version and Frequency Band
4.2	857
11.6	858	(% style="background-color:#dcdcdc" %)AT+FDR(%%) : Factory Data Reset
4.2	859
11.6	860	(% style="background-color:#dcdcdc" %)AT+PORT(%%) : Application Port
4.2	861
11.6	862	(% style="background-color:#dcdcdc" %)AT+CHS(%%) : Get or Set Frequency (Unit: Hz) for Single Channel Mode
4.2	863
11.6	864	(% style="background-color:#dcdcdc" %)AT+CHE(%%) : Get or Set eight channels mode, Only for US915, AU915, CN470
4.2	865
	866
6.3	867	= 4. FAQ =
4.2	868
6.3	869	== 4.1 How to change the LoRa Frequency Bands/Region? ==
	870
4.2	871	You can follow the instructions for [[how to upgrade image>>path:#3ygebqi]].
	872	When downloading the images, choose the required image file for download.
	873
	874
8.3	875	How to set up LSE01 to work in 8 channel mode By default, the frequency bands US915, AU915, CN470 work in 72 frequencies. Many gateways are 8 channel gateways, and in this case, the OTAA join time and uplink schedule is long and unpredictable while the end node is hopping in 72 frequencies.
4.2	876
	877
	878	You can configure the end node to work in 8 channel mode by using the AT+CHE command. The 500kHz channels are always included for OTAA.
	879
	880
	881	For example, in US915 band, the frequency table is as below. By default, the end node will use all channels (0~~71) for OTAA Join process. After the OTAA Join, the end node will use these all channels (0~~71) to send uplink packets.
	882
8.2	883	[[image:image-20220606154726-3.png]]
4.2	884
	885	When you use the TTN network, the US915 frequency bands use are:
	886
	887	* 903.9 - SF7BW125 to SF10BW125
	888	* 904.1 - SF7BW125 to SF10BW125
	889	* 904.3 - SF7BW125 to SF10BW125
	890	* 904.5 - SF7BW125 to SF10BW125
	891	* 904.7 - SF7BW125 to SF10BW125
	892	* 904.9 - SF7BW125 to SF10BW125
	893	* 905.1 - SF7BW125 to SF10BW125
	894	* 905.3 - SF7BW125 to SF10BW125
	895	* 904.6 - SF8BW500
	896
	897	Because the end node is now hopping in 72 frequency, it makes it difficult for the devices to Join the TTN network and uplink data. To solve this issue, you can access the device via the AT commands and run:
	898
8.3	899	(% class="box infomessage" %)
	900	(((
4.2	901	AT+CHE=2
8.3	902	)))
4.2	903
8.3	904	(% class="box infomessage" %)
	905	(((
4.2	906	ATZ
8.3	907	)))
4.2	908
	909	to set the end node to work in 8 channel mode. The device will work in Channel 8-15 & 64-71 for OTAA, and channel 8-15 for Uplink.
	910
	911
	912	The AU915 band is similar. Below are the AU915 Uplink Channels.
	913
8.2	914	[[image:image-20220606154825-4.png]]
4.2	915
	916
	917
4.8	918	= 5. Trouble Shooting =
4.2	919
4.9	920	== 5.1 Why I can’t join TTN in US915 / AU915 bands? ==
	921
4.11	922	It is due to channel mapping. Please see the [[Eight Channel Mode>>doc:Main.LoRaWAN Communication Debug.WebHome\|\|anchor="H2.NoticeofUS9152FCN4702FAU915Frequencyband"]] section above for details.
4.2	923
	924
4.10	925	== 5.2 AT Command input doesn’t work ==
4.2	926
6.2	927	In the case if user can see the console output but can’t type input to the device. Please check if you already include the (% style="color:green" %)ENTER(%%) while sending out the command. Some serial tool doesn’t send (% style="color:green" %)ENTER(%%) while press the send key, user need to add ENTER in their string.
4.2	928
	929
4.10	930	== 5.3 Device rejoin in at the second uplink packet ==
4.2	931
6.2	932	(% style="color:#4f81bd" %)Issue describe as below:
4.2	933
6.2	934	[[image:1654500909990-784.png]]
4.2	935
	936
6.2	937	(% style="color:#4f81bd" %)Cause for this issue:
4.2	938
	939	The fuse on LSE01 is not large enough, some of the soil probe require large current up to 5v 800mA, in a short pulse. When this happen, it cause the device reboot so user see rejoin.
	940
	941
6.2	942	(% style="color:#4f81bd" %)Solution:
4.2	943
	944	All new shipped LSE01 after 2020-May-30 will have this to fix. For the customer who see this issue, please bypass the fuse as below:
	945
6.2	946	[[image:1654500929571-736.png]]
4.2	947
4.7	948
4.4	949	= 6. Order Info =
4.2	950
	951
4.6	952	Part Number: (% style="color:#4f81bd" %)LSE01-XX-YY
4.2	953
	954
4.6	955	(% style="color:#4f81bd" %)XX(%%): The default frequency band
4.2	956
4.4	957	* (% style="color:red" %)AS923(%%): LoRaWAN AS923 band
	958	* (% style="color:red" %)AU915(%%): LoRaWAN AU915 band
	959	* (% style="color:red" %)EU433(%%): LoRaWAN EU433 band
	960	* (% style="color:red" %)EU868(%%): LoRaWAN EU868 band
	961	* (% style="color:red" %)KR920(%%): LoRaWAN KR920 band
	962	* (% style="color:red" %)US915(%%): LoRaWAN US915 band
4.5	963	* (% style="color:red" %)IN865(%%): LoRaWAN IN865 band
4.4	964	* (% style="color:red" %)CN470(%%): LoRaWAN CN470 band
4.2	965
4.4	966	(% style="color:#4f81bd" %)YY(%%): Battery Option
4.2	967
4.4	968	* (% style="color:red" %)4(%%): 4000mAh battery
	969	* (% style="color:red" %)8(%%): 8500mAh battery
4.2	970
4.3	971	= 7. Packing Info =
4.2	972
4.3	973	(((
4.2	974	Package Includes:
4.3	975	)))
4.2	976
4.3	977	* (((
	978	LSE01 LoRaWAN Soil Moisture & EC Sensor x 1
	979	)))
4.2	980
4.3	981	(((
	982
	983	)))
4.2	984
4.3	985	(((
4.2	986	Dimension and weight:
4.3	987	)))
4.2	988
4.3	989	* (((
	990	Device Size: cm
	991	)))
	992	* (((
	993	Device Weight: g
	994	)))
	995	* (((
	996	Package Size / pcs : cm
	997	)))
	998	* (((
	999	Weight / pcs : g
	1000	)))
4.2	1001
4.3	1002	= 8. Support =
4.2	1003
	1004	* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
	1005	* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]
	1006

Wiki source code of LSE01-LoRaWAN Soil Moisture & EC Sensor User Manual

Applications

Navigation