Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -54,25 +54,6 @@
54	54	[[image:image-20220530002453-3.png||height="262" width="493"]]
55	55
56	56
57		-= Configure GroPoint Air to Connect LoRaWAN Network =
58		-
59		-
60		-== LED Indicator  ( 检查等状态是否对的) ==
61		-
62		-The GroPoint Air has an internal LED which can show the status of different states.
63		-
64		-* The sensor is detected when the device is turned on, and it will flash 4 times quickly when it is detected.
65		-* Blink once when device transmits a packet.
66		-
67		-
68		-== Firmware and Changelog (Changelog标注现在 版本是什么版本) ==
69		-
70		-Firmware Download Location: [[https:~~/~~/www.dropbox.com/sh/4strg6w7kkekdc4/AAAUKdAV3XKhOi3t6YjA8j9za?dl=0>>https://www.dropbox.com/sh/4strg6w7kkekdc4/AAAUKdAV3XKhOi3t6YjA8j9za?dl=0]]
71		-
72		-Change Log:
73		-
74		-
75		-
76	76	= Configure GroPoint Air via AT Command or LoRaWAN Downlink =
77	77
78	78	Use can configure GroPoint Air via AT Command or LoRaWAN Downlink.
...	...	@@ -88,8 +88,12 @@
88	88
89	89	These commands are to configure:
90	90
91		-* General system settings like: uplink interval.
92		-* LoRaWAN protocol & radio-related command.
	72	+* (((
	73	+General system settings like: uplink interval.
	74	+)))
	75	+* (((
	76	+LoRaWAN protocol & radio-related command.
	77	+)))
93	93
94	94	They are the same for all Dragino Device that support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki: [[End Device AT Commands and Downlink Command>>url:http://8.211.40.43/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
95	95
...	...	@@ -114,9 +114,15 @@
114	114
115	115	If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
116	116
117		-* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
118		-* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
	102	+* (((
	103	+Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
	104	+)))
	105	+* (((
	106	+Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
119	119
	108	+
	109	+)))
	110	+
120	120	== 3.2 Set Interrupt Mode  （是否存在） ==
121	121
122	122	Feature, Set Interrupt mode for GPIO_EXIT.
...	...	@@ -131,8 +131,12 @@
131	131
132	132	This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
133	133
134		-* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
135		-* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
	125	+* (((
	126	+Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
	127	+)))
	128	+* (((
	129	+Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
	130	+)))
136	136
137	137	== 3.3 Get Firmware Version Info ~-~--（是否存在） ==
138	138