Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -61,7 +61,7 @@
61	61	* AT Command Connection: See [[FAQ>>url:http://8.211.40.43/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/#H6.FAQ]].
62	62	* LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>url:http://8.211.40.43/xwiki/bin/view/Main/]]
63	63
64		-There are two kinds of commands to configure GroPoint Air, they are:
	64	+There are two kinds of commands to configure GroPoint, they are:
65	65
66	66	* (((
67	67	**~ General Commands**.
...	...	@@ -69,17 +69,21 @@
69	69
70	70	These commands are to configure:
71	71
72		-* General system settings like: uplink interval.
73		-* LoRaWAN protocol & radio-related command.
	72	+* (((
	73	+General system settings like: uplink interval.
	74	+)))
	75	+* (((
	76	+LoRaWAN protocol & radio-related command.
	77	+)))
74	74
75	75	They are the same for all Dragino Device that support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki: [[End Device AT Commands and Downlink Command>>url:http://8.211.40.43/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
76	76
77	77
78	78	* (((
79		-**~ Commands special design for GroPoint Air**
	83	+**~ Commands special design for LLMS01**
80	80	)))
81	81
82		-These commands only valid for GroPoint Air, as below:
	86	+These commands only valid for LLMS01, as below:
83	83
84	84	== 3.1 Set Transmit Interval Time ==
85	85
...	...	@@ -95,9 +95,14 @@
95	95
96	96	If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
97	97
98		-* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
99		-* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
	102	+* (((
	103	+Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
	104	+)))
	105	+* (((
	106	+Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
100	100
	108	+
	109	+)))
101	101
102	102	== 3.2 Set Interrupt Mode  （是否存在） ==
103	103
...	...	@@ -113,10 +113,13 @@
113	113
114	114	This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
115	115
116		-* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
117		-* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
	125	+* (((
	126	+Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
	127	+)))
	128	+* (((
	129	+Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
	130	+)))
118	118
119		-
120	120	== 3.3 Get Firmware Version Info ~-~--（是否存在） ==
121	121
122	122	Feature: use downlink to get firmware version.