Last modified by Xiaoling on 2024/04/23 14:37
Change comment:
There is no comment for this version
Summary
-
Page properties (2 modified, 0 added, 0 removed)
Details
- Page properties
-
- Author
-
... ... @@ -1,1 +1,1 @@ 1 -XWiki. Edwin1 +XWiki.David - Content
-
... ... @@ -54,6 +54,24 @@ 54 54 [[image:image-20220530002453-3.png||height="262" width="493"]] 55 55 56 56 57 += Connect LoRaWAN Network = 58 + 59 + 60 +== LED Indicator == 61 + 62 +The GroPoint Air has an internal LED which can show the status of different states. 63 + 64 +* The sensor is detected when the device is turned on, and it will flash 4 times quickly when it is detected. 65 +* Blink once when device transmits a packet. 66 + 67 +== Firmware and Changelog == 68 + 69 +Firmware Download Location: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/GroPoint_Air/firmware/>>https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/GroPoint_Air/firmware/]] 70 + 71 +Change Log: 72 + 73 + 74 + 57 57 = Configure GroPoint Air via AT Command or LoRaWAN Downlink = 58 58 59 59 Use can configure GroPoint Air via AT Command or LoRaWAN Downlink. ... ... @@ -61,7 +61,7 @@ 61 61 * AT Command Connection: See [[FAQ>>url:http://8.211.40.43/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/#H6.FAQ]]. 62 62 * LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>url:http://8.211.40.43/xwiki/bin/view/Main/]] 63 63 64 -There are two kinds of commands to configure GroPoint, they are: 82 +There are two kinds of commands to configure GroPoint Air, they are: 65 65 66 66 * ((( 67 67 **~ General Commands**. ... ... @@ -69,21 +69,17 @@ 69 69 70 70 These commands are to configure: 71 71 72 -* ((( 73 -General system settings like: uplink interval. 74 -))) 75 -* ((( 76 -LoRaWAN protocol & radio-related command. 77 -))) 90 +* General system settings like: uplink interval. 91 +* LoRaWAN protocol & radio-related command. 78 78 79 79 They are the same for all Dragino Device that support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki: [[End Device AT Commands and Downlink Command>>url:http://8.211.40.43/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]] 80 80 81 81 82 82 * ((( 83 -**~ Commands special design for LLMS01**97 +**~ Commands special design for GroPoint Air** 84 84 ))) 85 85 86 -These commands only valid for LLMS01, as below:100 +These commands only valid for GroPoint Air, as below: 87 87 88 88 == 3.1 Set Transmit Interval Time == 89 89 ... ... @@ -99,17 +99,11 @@ 99 99 100 100 If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01. 101 101 102 -* ((( 103 -Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds 104 -))) 105 -* ((( 106 -Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds 116 +* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds 117 +* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds 107 107 108 - 109 -))) 119 +== 3.2 Set Interrupt Mode == 110 110 111 -== 3.2 Set Interrupt Mode (是否存在) == 112 - 113 113 Feature, Set Interrupt mode for GPIO_EXIT. 114 114 115 115 **AT Command: AT+INTMOD** ... ... @@ -122,14 +122,10 @@ 122 122 123 123 This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06. 124 124 125 -* ((( 126 -Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode 127 -))) 128 -* ((( 129 -Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger 130 -))) 133 +* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode 134 +* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger 131 131 132 -== 3.3 Get Firmware Version Info ~-~--(是否存在)==136 +== 3.3 Get Firmware Version Info == 133 133 134 134 Feature: use downlink to get firmware version. 135 135 ... ... @@ -146,7 +146,7 @@ 146 146 147 147 |=((( 148 148 **Size(bytes)** 149 -)))|=**1**|=**1**|=**1**|=** 1**|=**1**|=**5**|=**1**153 +)))|=**1**|=**1**|=**1**|=**2**|=**1**|=4|=**1** 150 150 |**Value**|Software Type|((( 151 151 Frequency 152 152 ... ... @@ -182,8 +182,10 @@ 182 182 183 183 *0x09: AS923-2 184 184 185 -*0x a0: AS923-3189 +*0x0A: AS923-3 186 186 191 +*0x0B: AS923-4 192 + 187 187 **Sub-Band**: value 0x00 ~~ 0x08 188 188 189 189 **Firmware Version**: 0x0100, Means: v1.0.0 version ... ... @@ -202,7 +202,9 @@ 202 202 203 203 0x06: LSNPK01 204 204 211 +0x07: LDDS45 205 205 213 +0x08: LSLP01 206 206 207 207 = Use AT Command = 208 208