Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -61,7 +61,7 @@
61	61	* AT Command Connection: See [[FAQ>>url:http://8.211.40.43/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/#H6.FAQ]].
62	62	* LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>url:http://8.211.40.43/xwiki/bin/view/Main/]]
63	63
64		-There are two kinds of commands to configure GroPoint, they are:
	64	+There are two kinds of commands to configure GroPoint Air, they are:
65	65
66	66	* (((
67	67	**~ General Commands**.
...	...	@@ -69,21 +69,17 @@
69	69
70	70	These commands are to configure:
71	71
72		-* (((
73		-General system settings like: uplink interval.
74		-)))
75		-* (((
76		-LoRaWAN protocol & radio-related command.
77		-)))
	72	+* General system settings like: uplink interval.
	73	+* LoRaWAN protocol & radio-related command.
78	78
79	79	They are the same for all Dragino Device that support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki: [[End Device AT Commands and Downlink Command>>url:http://8.211.40.43/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
80	80
81	81
82	82	* (((
83		-**~ Commands special design for LLMS01**
	79	+**~ Commands special design for GroPoint Air**
84	84	)))
85	85
86		-These commands only valid for LLMS01, as below:
	82	+These commands only valid for GroPoint Air, as below:
87	87
88	88	== 3.1 Set Transmit Interval Time ==
89	89
...	...	@@ -99,14 +99,9 @@
99	99
100	100	If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
101	101
102		-* (((
103		-Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
104		-)))
105		-* (((
106		-Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
	98	+* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
	99	+* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
107	107
108		-
109		-)))
110	110
111	111	== 3.2 Set Interrupt Mode  （是否存在） ==
112	112
...	...	@@ -122,13 +122,10 @@
122	122
123	123	This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
124	124
125		-* (((
126		-Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
127		-)))
128		-* (((
129		-Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
130		-)))
	116	+* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
	117	+* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
131	131
	119	+
132	132	== 3.3 Get Firmware Version Info ~-~--（是否存在） ==
133	133
134	134	Feature: use downlink to get firmware version.