LPS8N - LoRaWAN Gateway User Manual

The LPS8N is an (% style="color:#4f81bd" %)**open source LoRaWAN Indoor Gateway**(%%). It lets you bridge LoRa wireless network to an IP network via WiFi, Ethernet, 3G or 4G cellular network. The LoRa wireless allows users to send data and reach extremely long ranges at low data-rates.

23

)))

24

25

(((

26

The LPS8N uses (% style="color:#4f81bd" %)**Semtech packet forwarder**(%%) & (% style="color:#4f81bd" %)**LoRaWAN Station connection**(%%) and fully compatible with LoRaWAN protocol. It includes a (% style="color:#4f81bd" %)**SX1302 LoRaWAN concentrator**(%%), which provides 10 programmable parallel demodulation paths.

)))

(((

LPS8N has (% style="color:#4f81bd" %)**pre-configured standard LoRaWAN frequency bands**(%%) to use for different countries. User can also (% style="color:#4f81bd" %)**customized the frequency bands** (%%)to use in their own LoRa network.

)))

(((

LPS8N can communicate with ABP LoRaWAN end node without LoRaWAN server. System integrator can use it to integrate with their existing IoT Service without set up own LoRaWAN server or use 3rd party LoRaWAN service.

)))

(((

)))

[[image:image-20220826090251-1.png]]

42

43

44

== 1.2 Specifications ==

45

46

47

(% style="color:#037691" %)**Hardware System:**

(((

Linux Part:

)))

* 400Mhz ar9331 processor

* 64MB RAM

* 16MB Flash

(% style="color:#037691" %)**Interface:**

58

59

* 10M/100M RJ45 Ports x 1

60

* WiFi : 802.11 b/g/n

61

* LoRaWAN Wireless

62

* Power Input: 5V DC, 2A, Type C

63

* USB 2.0 host connector x 1

64

* Mini-PCI E connector x 1

65

* SX1302 + 2 x SX1250

66

67

(% style="color:#037691" %)**WiFi Spec:**

68

69

* IEEE 802.11 b/g/n

70

* Frequency Band: 2.4 ~~ 2.462GHz

71

* Tx power:

72

** 11n tx power : mcs7/15: 11db mcs0 : 17db

73

** 11b tx power: 18db

74

** 11g 54M tx power: 12db

75

** 11g 6M tx power: 18db

* Wifi Sensitivity

** 11g 54M : -71dbm

** 11n 20M : -67dbm

(% style="color:#037691" %)**LoRa Spec:**

81

82

* Up to -140 dBm sensitivity

83

* 70 dB CW interferer rejection at 1 MHz offset

84

* Able to operate with negative SNR, CCR up to 9dB

85

* Emulates 49 x LoRa demodulators and 1 x (G)FSK demodulator

86

* Dual digital TX & RX radio front-end interfaces

87

* 10 programmable parallel demodulation paths

88

* Dynamic data-rate (DDR) adaptation

89

* True antenna diversity or simultaneous dual-band operation

90

91

(% style="color:#037691" %)**Cellular 4G LTE (optional):**

92

93

* Quectel [[**EC25 LTE module**>>url:https://www.quectel.com/product/ec25minipcie.htm]]

94

* Micro SIM Slot

95

* External 4G Sticker Antenna.

96

* Up to 150Mbps downlink and 50Mbps uplink data rates

97

* Worldwide LTE,UMTS/HSPA+ and GSM/GPRS/EDGE coverage

98

* MIMO technology meets demands for data rate and link reliability in modem wireless communication systems

== 1.3 Features ==

* Open Source OpenWrt system

104

* Managed by Web GUI, SSH via WAN or WiFi

105

* Remote access with Reverse-SSH or remote.it

106

* Emulates 49x LoRa demodulators

107

* LoRaWAN Gateway

108

* 10 programmable parallel demodulation paths

109

* Pre-configure to support different LoRaWAN regional settings.

110

* Allow to customize LoRaWAN regional parameters.

111

* Support Local decode ABP end node info and transfer to MQTT server

112

* Support different level log in.

113

* Support Semtech Packet Forwarder

114

* Support LoRaWAN basic station.

115

* Optional 3G/4G cellular connection

116

117

== 1.4 Hardware System Structure ==

118

119

120

[[image:image-20220830153228-1.png]]

121

122

123

== 1.5 LPS8N Applications ==

124

125

126

[[image:1657079055940-721.png]]

127

128

129

== 1.6 LED Indicators ==

130

131

132

LPS8N has totally four LEDs, They are:

133

134

* **Power LED **[[image:image-20220706115518-1.png||height="15" width="16"]] : This (% style="color:red" %)**RED LED**(%%) will be **solid on** if the device is properly powered.

135

* **Wireless LED** [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/LG308N%20-%20LoRaWAN%20Gateway%20User%20Manual/WebHome/image-20220705165446-6.png?width=15&height=15&rev=1.1||alt="image-20220705165446-6.png" height="15" width="15"]]: No function yet.

136

* **SYS LED ** [[image:image-20220706115518-3.png||height="16" width="16"]] : This **RGB LED** will shows different colors on different state:

137

** (% style="color:blue" %)**SOLID BLUE**(%%): Device is alive with LoRaWAN server connection.

138

** (% style="color:blue" %)**BLINKING BLUE**(%%): a) Device has internet connection but no LoRaWAN Connection. or b) Device is in booting stage, in this stage, it will (% style="color:blue" %)**BLINKING BLUE**(%%) for several seconds and then with (% style="color:red" %)**SOLID RED**(%%) and (% style="color:blue" %)**BLINKING BLUE**(%%) together

139

** (% style="color:red" %)**SOLID RED**(%%): Device doesn't have Internet connection.

140

141

* **ETH LED **[[image:image-20220706115518-4.png||height="15" width="17"]] : This LED shows the ETH interface connection status.

142

143

== 1.7 Button Instruction ==

144

145

146

LPS8N has a black toggle button, which is:

147

148

149

(% style="color:blue" %)**//➢ //Long press 4-5s: **(%%)the gateway will reload the Network and Initialize wifi configuration

150

151

**LED status: ** SYS LED will BLINKING BLUE Until the reload is finished.

152

153

154

(% style="color:blue" %)**➢ Long press more than 30s: **(%%)the gateway will restart and restore factory settings.

155

156

**LED status: ** When the user releases the button, the LED will TURN OFF.

157

158

159

= 2. Access and Configure LPS8N =

(((

The LPS8N is configured as a WiFi Access Point by factory default. You can access and configure the LPS8N after connecting to its WiFi network, or via its WAN Ethernet port.

)))

== 2.1 Find IP address of LPS8N ==

168

169

=== 2.1.1 Connect via WiFi ===

170

171

172

[[image:1657085974260-168.png]]

173

174

175

At the first boot of LPS8N, it will auto generate a WiFi network called (% style="color:green" %)**//dragino-xxxxxx //**(% style="color:black" %)with password: (% style="background-color:yellow" %)dragino+dragino

176

177

178

[[image:1652413127647-377.png]]

(((

User can use a PC to connect to this WiFi network. The PC will get an IP address 10.130.1.xxx and the DLOS8N has the default IP (% style="color:green" %)10.130.1.1

)))

=== 2.1.2 Connect via Ethernet with DHCP IP from router ===

188

189

190

[[image:1657086105922-299.png]]

(((

Alternatively, connect the LPS8N Ethernet port to your router and LPS8N will obtain an IP address from your router. In the router's management portal, you should be able to find what IP address the router has assigned to the LPS8N. You can also use this IP to connect.

)))

=== 2.1.3 Connect via WiFi with DHCP IP from router ===

200

201

202

[[image:1657086192720-649.png]]

203

204

205

If the LPS8N already connect to the router via WiFi, use can use the WiFi IP to connect to LPS8N.

206

207

208

=== 2.1.4 Connect via Ethernet with fall back ip ===

209

210

211

The WAN port also has a [[fall back ip address>>||anchor="H10.3A0IconfiguredLPS8NforWiFiaccessandlostitsIP.Whattodonow3F"]] for access if user doesn't connect to uplink router. Click [[here>>||anchor="H10.3A0IconfiguredLPS8NforWiFiaccessandlostitsIP.Whattodonow3F"]] to see how to configure.

212

213

214

== 2.2 Access Configure Web UI ==

**Web Interface**

Open a browser on the PC and type the LPS8N ip address (depends on your connect method)

220

221

[[http:~~/~~/10.130.1.1/>>url:http://10.130.1.1/]] (Access via WiFi AP network)

or

http:~/~/IP_ADDRESS or [[http:~~/~~/ IP_ADDRESS:8000>>url:http://192.168.1.xx:8000]]

226

227

228

You will see the login interface of LPS8N as shown below.

229

230

The account details for Web Login are:

231

232

(% style="color:#4f81bd" %)**User Name: root**

233

234

(% style="color:#4f81bd" %)**Password: dragino**

235

236

[[image:1652414287022-223.png]]

237

238

239

= 3. Typical Network Setup =

== 3.1 Overview ==

The LPS8N supports flexible network set up for different environments. This section describes the typical network topology. The network set up includes:

245

246

* **WAN Port Internet Mode**

247

* **WiFi Client Mode**

248

* **WiFi AP Mode**

249

250

== 3.2 Use WAN port to access Internet ==

251

252

253

By default, the LPS8N is set to use the WAN port to connect to an upstream network. When you connect the LPS8N's WAN port to an upstream router, LPS8N will get an IP address from the router and have Internet access via the upstream router. The network status can be checked in the (% style="color:#4f81bd" %)**home page**:

254

255

256

[[image:1657088560833-398.png]]

257

258

259

== 3.3 Access the Internet as a WiFi Client ==

260

261

262

In the WiFi Client Mode, LPS8N acts as a WiFi client and gets DHCP from an upstream router via WiFi.

263

264

(((

265

The settings for WiFi Client is under page (% style="color:#4f81bd" %)**System~-~-> WiFi ~-~-> WiFi WAN Client Settings**

266

267

268

[[image:1657088818095-182.png]]

)))

(((

In the WiFi Survey Choose the WiFi AP, and input the Passphrase then click Save & Apply to connect.

)))

== 3.4 Use built-in 4G modem for internet access ==

(((

(((

If the LPS8N has 3G/4G Cellular modem, user can use it as main internet connection or back up.

)))

(((

First, install the Micro SIM card as below direction

)))

(((

Second, Power off/ ON LPS8N to let it detect the SIM card.

)))

)))

[[image:1657090855037-497.png]]

(((

)))

(((

The set up page is (% style="color:#4f81bd" %)**System ~-~-> Cellular**

)))

(((

While use the cellular as Backup WAN, device will use Cellular for internet connection while WAN port or WiFi is not valid and switch back to WAN port or WiFi after they recover.

)))

(((

[[image:1657090932270-444.png]]

)))

== 3.5 Check Internet connection ==

319

320

321

In the (% style="color:#4f81bd" %)**home**(%%) page, we can check the Internet connection.

322

323

* GREEN Tick [[image:1652436675869-206.png||height="14" width="15"]] : This interface has Internet connection.

324

* Yellow Tick [[image:1652436705761-420.png||height="15" width="15"]] : This interface has IP address but don't use it for internet connection.

325

* RED Cross [[image:1652436787176-950.png||height="14" width="15"]] : This interface doesn't connected.

326

327

[[image:1657091099235-452.png]]

328

329

330

= 4. Example: Configure as a LoRaWAN gateway =

331

332

333

LPS8N is fully compatible with LoRaWAN protocol. It uses the legacy Semtech Packet forwarder to forward the LoRaWAN packets to server. The structure is as below.

(((

[[image:image-20220826090251-1.png]]

)))

(((

This chapter describes how to use the LPS8N to work with (TTN v3)[[ LoRaWAN Server>>url:https://www.thethingsnetwork.org/]] ([[www.thethingsnetwork.org>>url:http://www.thethingsnetwork.org/]])

)))

== 4.1 Create a gateway in TTN V3 Server ==

346

347

348

(% style="color:blue" %)**Step 1: Get a Unique gateway ID.**

(((

Every LPS8N has a unique gateway id. The ID can be found at LoRaWAN page:

)))

(((

[[image:1657091583941-544.png]]

)))

The example gateway id is: (% style="color:green" %)**a840411e96744154**

(% style="color:blue" %)**Step 2: Sign up a user account in TTN server**

368

369

370

[[**https:~~/~~/account.thethingsnetwork.org/register**>>url:https://account.thethingsnetwork.org/register]]

371

372

373

[[image:1657091739530-531.png]]

(% style="color:blue" %)**Step 3: Choose the TTNv3 Cluster Picker**

(((

[[image:1657091719947-297.png]]

)))

(% style="color:red" %)**Note: Choose the cluster corresponds to a specific Gateway server address**

387

388

389

* Europe 1** (% style="color:red" %)corresponding Gateway server address:(%%)**(% style="color:red" %) (% style="color:black" %)eu1.cloud.thethings.network

390

* North America 1 (% style="color:red" %)**corresponding Gateway server address: **(% style="color:black" %)nam1.cloud.thethings.network

391

* Australia 1 (% style="color:red" %)**corresponding Gateway server address: **(% style="color:black" %)au1.cloud.thethings.network

392

* Legacy V2 Console : (% style="color:red" %)**TTN v2 shuts down in December 2021**

393

394

(% style="color:blue" %)**Step 4: Create a Gateway**

395

396

397

[[image:1657091941182-367.png]]

398

399

Click the Gateway icon and then click Add gateway.

400

401

402

Open the following page:

403

404

405

[[image:image-20220706155323-5.png||height="579" width="1060"]]

406

407

408

[[image:image-20220706155323-6.png||height="582" width="1066"]]

(((

(% style="color:red" %)**Notice: Gateway Server address must match the gateway configuration, otherwise you will have problem for End Node to join the network.**

)))

After creating the gateway, you can see the gateway info, as below.

418

419

[[image:1657094130908-567.png]](% style="display:none" %)

420

421

422

== 4.2 Configure LPS8N to connect to TTN v3 ==

(((

You can now configure the LPS8N to let it connect to TTN network V3.

)))

(((

Make sure your LPS8N has a working Internet Connection first.

)))

(((

Choose the right server provider and click (% style="color:#4f81bd" %)**Save&Apply.**

)))

[[image:1657094183213-301.png]]

440

441

442

(% style="color:red" %)**Note: The server address must match the Gateway server address you choose in TTN V3.**

443

444

445

In the home page, we can see the LoRaWAN connection is ready now.

446

447

448

[[image:1657094202420-798.png]]

In TTN v3 portal, we can also see the gateway is connected.

453

454

[[image:1657094221515-510.png]]

455

456

457

== 4.3 Configure frequency ==

458

459

460

We also need to set the frequency plan in LPS8N to match the end node we use, so to receive the LoRaWAN packets from the LoRaWAN sensor.

461

462

463

[[image:1657094249818-468.png]]

In logread page, user can check the frequency actually used.

468

469

[[image:1657094333704-207.png]]

470

471

472

== 4.4 Add a LoRaWAN End Device ==

(((

This section shows how to add a LoRaWAN End device to a LoRaWAN network and see the data from TTN web site.

)))

(((

We use [[LT-22222-L>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/156-lt-22222-l.html]] IO Controller as a reference device - the setup for other LoRaWAN devices will be similar.

481

)))

482

483

[[image:1652422794767-871.png]]

(((

(% style="color:blue" %)**Step 1**: (%%)Create a Device definition in TTN v3 with the OTAA keys from the example LT-22222-L IO Controller device.

)))

(((

Three codes are required to define the device in TTN v3:

494

)))

495

496

* DEV EUI - Unique ID code for a particular device.

497

* APP EUI - ID code for an Application defined in TTN v3.

498

* APP Key - Unique key to secure communications with a particular device.

499

500

(((

501

A set of these codes are stored in each device by the manufacturer as the default codes for that particular device. Each device is shipped with a sticker with the default Device EUI as shown below.

)))

[[image:1657094382177-591.png]]

(((

(% style="color:red" %)**Note: You may be able to change these codes in a device by using a configuration facility on the device e.g. the LT-22222 uses a serial port access and a series of AT commands. Changing the codes may be necessary in the case where you have to use codes assigned by a LoRa WAN server.**

)))

(((

For the TTN v3 server, you can use the codes set in the device as in the following example.

)))

(((

Select **Add Application** to open the screen below.

)))

[[image:1657094417175-831.png]]

526

527

Open the **Application **select** Add end device**

528

529

530

Start Register the end device

531

532

[[image:1657094444802-101.png]]

533

534

(((

535

Select OTAA activation mode

)))

(((

The LoRaWAN version for your device should be provided by the manufacturer in a datasheet as LoRaWAN version or LoRaWAN specification. The most commonly used LoRaWAN versions are v1.0.2 and v1.0.3.

542

)))

543

544

[[image:1657094475730-208.png]]

545

546

First, input the End device ID, AppEUI and DevEUI.

547

548

549

[[image:1657094646429-966.png]]

550

551

Secondly, choose the corresponding frequency and LoRaWAN class capabilities.

552

553

554

[[image:1657094674045-755.png]]

555

556

(((

557

Finally, Application layer settings input the corresponding AppKey. Before saving the configuration, check that the data matches the device.

)))

(((

(% style="color:blue" %)**Step 2**: (%%)Power on LT-22222-L device and it will automatically join the TTN network. After joining successfully, it will start to upload messages to the TTN v3. Select the Live data tab and you will see the data appearing in the panel.

)))

(((

(% style="color:red" %)**Note that it may take some time for the device data to appear in the TTN v3 display.**

)))

[[image:1657094791060-639.png]]

575

576

577

= 5. Web Configure Pages =

== 5.1 Home ==

Shows the system running status.

583

584

585

[[image:1657094893942-726.png]]

586

587

588

== 5.2 LoRa Settings ==

589

590

=== 5.2.1 LoRa ~-~-> LoRa ===

(((

This page shows the LoRa Radio Settings. There are a set of default frequency band according to LoRaWAN protocol, and user can customized the band* as well.

)))

(((

Different LPS8N hardware version can support different frequency range:

599

)))

600

601

* (% style="color:blue" %)**868**(%%): valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.

602

* (% style="color:blue" %)**915**(%%): valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920

(((

(((

After user choose the frequency plan, he can see the actually frequency in used by checking the page (% style="color:green" %)**LogRead ~-~-> LoRa Log**

)))

)))

[[image:1657094930903-357.png]]

615

616

(% style="color:red" %)**Note *:** **[[See this instruction for how to customize frequency band>>doc:Main.How to customized LoRaWAN frequency band.WebHome]]**

617

618

619

=== 5.2.2 LoRa ~-~-> ABP Decryption ===

620

621

622

The LPS8N can communicate with LoRaWAN ABP End Node without the need of LoRaWAN server. It can be used in some cases such as:

623

624

* No internet connection.

625

* User wants to get data forward in gateway and forward to their server based on MQTT/HTTP, etc. (Combine ABP communication method and [[MQTT forward together>>doc:Main.MQTT Forward Instruction.WebHome]]).

626

627

(((

628

Detail of this feature: **[[Communication with ABP End Node>>doc:Main.Communicate with ABP End Node without LoRaWAN Network Server --- LG308.WebHome]]**

)))

[[image:1657095412271-942.png]]

634

635

636

== 5.3 LoRaWAN Settings ==

637

638

=== 5.3.1 LoRaWAN ~-~-> LoRaWAN ===

639

640

641

This page is for the connection set up to a general LoRaWAN Network server such as: [[TTN>>url:http://www.thethingsnetwork.org/]], [[ChirpStack>>url:https://www.chirpstack.io/]] etc.

642

643

644

[[image:1652423628833-467.png||height="357" width="755"]]

645

646

647

(% style="color:red" %)**Note:**

648

649

~*: User can ignore the latitude and longitude settings here, LPS8N will use the actually value from GPS module.

650

651

~**: Packet filter is to drop the unwanted LoRaWAN packet, instruction see here:

652

653

**See:** **[[Filter unwanted LoRaWAN packets>>doc:Main.Filter unwanted LoRaWAN packets.WebHome]]**

654

655

656

=== 5.3.2 LoRaWAN ~-~-> LoRaWAN ~-~- Basic Station ===

657

658

659

[[image:image-20230406172421-1.png]]

(((

Please see this instruction to know more detail and a demo of how to connect to **[[AWS-IoT LoRaWAN Core>>doc:Main.AWS IoT Core for LoRaWAN.WebHome]].**

664

665

666

The basic station mode support **TTN/AWS/Chirpstack/ThingPark/Senet** Platform.

Instruction:

[[The Thing Network>>http://wiki.dragino.com/xwiki/bin/view/Main/Notes%20for%20TTN/#H3.A0GatewayRegistrationforBasicsStation]]

671

672

[[AWS-IoT LoRaWAN Core>>http://wiki.dragino.com/xwiki/bin/view/Main/AWS%20IoT%20Core%20for%20LoRaWAN/]]

673

674

[[Chirpstack>>http://wiki.dragino.com/xwiki/bin/view/Main/Notes%20for%20ChirpStack/#H3.A0GatewayRegistrationforBasicsStation]]

ThingPark

[[Senet>>http://wiki.dragino.com/xwiki/bin/view/Main/Connection%20to%20Senet/#H3.A0SemtechBasicStation]]

679

)))

680

681

=== 5.3.3 LoRaWAN ~-~-> LORIOT ===

(((

Settings to communicate to LORIOT LoRaWAN Network Server: [[https:~~/~~/www.loriot.io/>>url:https://www.loriot.io/]]

)))

(((

Instruction: **[[Notes for LORIOT>>doc:Main.Notes for LORIOT.WebHome]]**

)))

[[image:1652428648903-878.png||height="266" width="731"]]

695

696

697

== 5.4 MQTT Settings ==

(((

If end nodes works in ABP mode, user can configure LPS8N to transfer the data to MQTT broker,

)))

(((

Instruction: **[[MQTT Forward Instruction>>doc:Main.MQTT Forward Instruction.WebHome]]**

)))

[[image:1652428705046-212.png||height="417" width="733"]]

== 5.5 System ==

=== 5.5.1 System ~-~-> System Overview ===

715

716

717

Shows the system info:

718

719

720

[[image:image-20220826091810-6.png]]

721

722

723

=== 5.5.2 System ~-~-> General ( login settings) ===

724

725

726

[[image:1657155183982-792.png]]

(((

(% style="color:#037691" %)**__System Password:__**

)))

(((

There are two login for LPS8N: (% style="color:blue" %)**root /dragino** (%%)or (% style="color:blue" %)**admin /dragino**. (%%)Both root and admin has the same right for WEB access. But root user has also the right to access via SSH to Linux system. admin only able to access WEB interface.

)))

(((

This page can be used to set the password for them.

)))

(((

(% style="color:#037691" %)**__Timezone: __**(%%)Set device timezone.

)))

(((

(% style="color:#037691" %)**__Port forwarding: __**(%%)Enable/Disable the HTTP and SSH access via WAN interface.

)))

=== 5.5.3 System ~-~-> Network ===

752

753

754

[[image:1657155288223-566.png]]

(((

(% style="color:#037691" %)**__LAN Settings: __**(%%)When the LPS8N has the AP enable, LAN settings specify the network info for LPS8N's own network.

)))

(((

(% style="color:#037691" %)__**WAN Settings: **__(%%)Setting for LPS8N WAN port

)))

(((

(% style="color:#037691" %)__**WiFi Settings: **__** **(%%)Setting for LPS8N WiFi IP when use it as WiFi Client

)))

=== 5.5.4 System ~-~-> WiFi ===

LPS8N WiFi Settings.

[[image:1657155457089-430.png]]

778

779

780

=== 5.5.5 System ~-~-> Cellular ===

781

782

783

While use the cellular as Backup WAN, device will use Cellular for internet connection while WAN port or WiFi is not valid and switch back to WAN port or WiFi after they recover.

784

785

786

[[image:1657155507672-204.png]]

787

788

789

(% style="color:red" %)**Note *: For LPS8N which doesn't have the cellular module, this page will shows Cellular not detected.**

790

791

792

=== 5.5.6 System ~-~-> Network Status ===

793

794

795

[[image:1657155554265-721.png]]

796

797

798

=== 5.5.7 System ~-~-> Remote Mgnt & Auto Provision ===

799

800

801

Auto Provision is the feature for batch configure and remote management. It can be used in below two cases:

802

803

804

[[image:image-20220707112053-4.png||height="451" width="995"]]

805

806

[[image:image-20220707112053-5.png||height="453" width="1004"]]

807

808

(% style="display:none" %)

809

810

(% style="display:none" %) [[image:1657157402578-508.png||height="450" width="992"]]

811

812

(% id="cke_bm_589629S" style="display:none" %) [[image:image-20220707092040-2.png||height="452" width="1002"]]

813

814

[[image:image-20220826091725-5.png||height="479" width="1004"]]

(((

Please see this document for detail: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8N/Firmware/Application_Note/&file=Auto-update-feature.pdf>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Application_Note/&file=Auto-update-feature.pdf]]

819

)))

820

821

(% style="display:none" %) (%%)

822

823

(((

824

R-SSH is for remote access device and management, introduction for how to use: [[Remote Access Gateway>>doc:Main.Monitor & Remote Access Gateway.WebHome]]

)))

[[image:1652429624400-864.png||height="432" width="716"]]

830

831

832

=== 5.5.8 System ~-~-> Firmware Upgrade ===

833

834

835

We keep improving the LPS8N Linux side firmware for new features and bug fixes. Below are the links for reference.

836

837

* **Latest firmware**: [[LoRa Gateway Firmware>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG02-OLG02/Firmware/]],

838

839

( [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8N/Firmware>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LIG16/Firmware]])

840

841

* **Change Log**: [[Firmware Change Log>>url:http://www.dragino.com/downloads/downloads/LoRa_Gateway/LG02-OLG02/Firmware/ChangeLog]].

842

843

( [[http:~~/~~/www.dragino.com/downloads/downloads/LoRa_Gateway/LPS8N/Firmware/ChangeLog>>url:http://www.dragino.com/downloads/downloads/LoRa_Gateway/LIG16/Firmware/ChangeLog]] )

(((

The file named as (% style="color:green" %)**xxxxx–xxxxx-squashfs-sysupgrade.bin **(% style="color:black" %)is the upgrade Image. There are different methods to upgrade, as below.

)))

(((

(% style="color:green" %)**Web~-~-> System~-~-> Firmware Upgrade**

)))

[[image:1657156052651-770.png]]

(((

Select the required image and click (% style="color:blue" %)**Flash Image.**(%%) The image will be uploaded to the device, and then click (% style="color:blue" %)**Process Update**(%%) to upgrade.

)))

(((

(% style="color:red" %)**NOTE**: (%%)You normally need to (% style="color:blue" %)**//uncheck//**(%%) the (% style="color:blue" %)**Preserve Settings**(%%) checkbox when doing an upgrade to ensure that there is no conflict between the old settings and the new firmware. The new firmware will start up with its default settings.

)))

(((

The system will automatically boot into the new firmware after upgrade.

)))

[[image:1657156094153-520.png]]

877

878

879

(% style="color:red" %)**NOTE***(%%): User can also upgrade firmware via Linux console

880

881

SCP the firmware to the system(% style="color:green" %)**/var**(%%)** **directory and then run

882

883

(% style="color:#4f81bd" %)**//root@OpenWrt:~~# /sbin/sysupgrade –n /var/Your_Image//**

884

885

886

(% style="color:red" %)**NOTE**(%%) : it is important to transfer the image in the /var directory, otherwise it may exceed the available flash size.

887

888

889

=== 5.5.9 System ~-~-> Reboot/Reset ===

890

891

892

[[image:1652430197132-330.png||height="256" width="724"]]

(((

)))

=== 5.5.10 System ~-~-> Package Maintain ===

899

900

901

[[image:1657156199070-491.png]]

902

903

904

Place to show what package has installed and possible to upgrade packages.

== 5.6 LogRead ==

=== 5.6.1 LogRead ~-~-> LoRa Log ===

910

911

912

Show the frequency for LoRa Radio and traffics.

913

914

915

[[image:1657156300781-933.png]]

916

917

918

=== 5.6.2 LogRead ~-~-> System Log ===

Show the system log

[[image:1657156341198-226.png]]

= 6. More features =

== 6.1 Packet Filtering ==

(((

Drop unwanted packets.

)))

(((

See: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Filter%20unwanted%20LoRaWAN%20packets/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Filter%20unwanted%20LoRaWAN%20packets/]]

)))

== 6.2 Remote Access ==

(((

Remote Access Devices for management.

)))

(((

Instruction: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Monitor%20%26%20Remote%20Access%20Gateway/?Remote%20Access>>http://wiki.dragino.com/xwiki/bin/view/Main/Monitor%20%26%20Remote%20Access%20Gateway/?Remote%20Access]]

)))

== 6.3 How to decode ABP LoRaWAN node ==

(((

Decode ABP:

)))

(((

[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Communicate%20with%20ABP%20End%20Node%20without%20LoRaWAN%20Network%20Server%20~~-~~--%20LG308/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Communicate%20with%20ABP%20End%20Node%20without%20LoRaWAN%20Network%20Server%20---%20LG308/]]

)))

== 6.4 How to set data to MQTT broker ==

(((

Only support ABP LoRaWAN End Node

)))

(((

Instruction: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/MQTT%20Forward%20Instruction/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/MQTT%20Forward%20Instruction/]]

974

975

976

== 6.5 How the gateway connects to Chirpstack v3/v4 via gateway-bridge ==

977

978

979

If the Chirpstack v3 Gateway-bridge is used, the corresponding gateway firmware must be used :

980

981

[[Chirpstack-gateway-bridge/Chirpstack-Bridge-V3.14.6-Bridge~~-~~-build-v5.4.1679487778-20230322-2024/>>https://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Release/Chirpstack-gateway-bridge/Chirpstack-Bridge-V3.14.6-Bridge--build-v5.4.1679487778-20230322-2024/]]

982

983

Chirpstack v3 via gateway-bridge Instruction: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Notes%20for%20ChirpStack/#H4.A0A0HowthegatewayconnectstoChirpstackv3viagateway-bridge>>http://wiki.dragino.com/xwiki/bin/view/Main/Notes%20for%20ChirpStack/#H4.A0A0HowthegatewayconnectstoChirpstackv3viagateway-bridge]]

984

985

986

If the Chirpstack v4 Gateway-bridge is used, the corresponding gateway firmware must be used :

987

988

[[Chirpstack-gateway-bridge/Chirpstack-Bridge-V4~~-~~-build-v5.4.1670655072-20221210-1452/>>https://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Release/Chirpstack-gateway-bridge/Chirpstack-Bridge-V4--build-v5.4.1670655072-20221210-1452/]]

989

990

Chirpstack v4 via gateway-bridge Instruction: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Notes%20for%20ChirpStack/#H4.A0HowthegatewayconnectstoChirpstackv4viagateway-bridge>>http://wiki.dragino.com/xwiki/bin/view/Main/Notes%20for%20ChirpStack/#H4.A0HowthegatewayconnectstoChirpstackv4viagateway-bridge]]

)))

(% style="color:red" %)**Note**(%%): Different chirpstack versions use different gateway-bridge configurations.

996

997

After updating the Chirpstack gateway-bridge firmware, there is no need to re-download and install the Chirpstack gateway-bridge package

998

999

1000

== 6.6 More instructions ==

1001

1002

1003

[[LoRaWAN Gateway Instruction>>doc:Main.WebHome]](LoRaWAN Gateway)

1004

1005

1006

== 6.7 Auto-Provision ==

1007

1008

1009

Auto Provision is the feature for batch configure and remote management. It can be used in below two cases:

1010

1011

[[image:image-20220707092040-1.png||height="451" width="995"]]

1012

1013

[[image:image-20220707092040-2.png||height="452" width="1002"]]

1014

1015

[[image:image-20220826091546-4.png]](% style="display:none" %)

(((

Please see this document for detail: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8N/Firmware/Application_Note/&file=Auto-update-feature.pdf>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Application_Note/&file=Auto-update-feature.pdf]]

1020

)))

1021

1022

(% style="display:none" %) (%%)

1023

1024

= 7. (% style="display:none" %) (%%)Linux System =

1025

1026

1027

The LPS8N is based on the OpenWrt Linux system. It is open source, and users are free to configure and modify the Linux settings.

1028

1029

(% style="display:none" %) (%%)

1030

1031

== 7.1 SSH Access for Linux console ==

1032

1033

1034

User can access the Linux console via the SSH protocol. Make sure your PC and the LPS8N are connected to the same network, then use a SSH tool (such as [[putty>>url:http://www.chiark.greenend.org.uk/~~sgtatham/putty/download.html]] in Windows) to access it.

1035

1036

IP address: IP address of LPS8N

1037

1038

Port: 22 (via WiFi AP mode) or 2222 (via WAN Interface)

1039

1040

User Name: (% style="color:green" %)**root**

1041

1042

Password: (% style="color:green" %)**dragino** (% style="color:black" %)(default)

1043

1044

After logging in, you will be in the Linux console and can enter commands as shown below.

1045

1046

1047

[[image:1657158198733-338.png]]

1048

1049

1050

The “** (% style="background-color:yellow" %)logread -f(%%)**(% style="background-color:yellow" %)” (%%)command can be used to debug how system runs.

1051

1052

1053

[[image:1657158190234-805.png]]

1054

1055

1056

== 7.2 Edit and Transfer files ==

(((

The LPS8N supports the (% style="color:green" %)**SCP protocol** (% style="color:black" %)and has a built-in (% style="color:green" %)**SFTP server**. (% style="color:black" %)There are many ways to edit and transfer files using these protocols.

)))

(((

In Windows, one of the easiest methods is using the [[WinSCP>>url:https://winscp.net/eng/index.php]] utility.

)))

(((

After establishing access via WinSCP to the device, you can use an FTP style window to drag / drop files to the LPS8N, or edit the files directly in the windows.

)))

(((

Screenshot is as below:

1073

)))

1074

1075

[[image:1652431650755-450.png]]

1076

1077

1078

== 7.3 File System ==

(((

The LPS8N has a 16MB flash and a 64MB RAM. The /var and /tmp directories are in the RAM, so contents stored in /tmp and /var will be erased after rebooting the device. Other directories are in the flash and will remain after reboot.

)))

(((

The Linux system uses around 8MB ~~10MB flash size which means there is not much room for user to store data in the LPS8N flash.

)))

(((

You can use an external USB flash memory device to extend the size of flash memory for storage.

)))

== 7.4 Package maintenance system ==

1095

1096

1097

LPS8N uses the OpenWrt [[**OPKG package maintenance system**>>https://oldwiki.archive.openwrt.org/doc/techref/opkg]]. There are more than 3000+ packages available in our package server for users to install for their applications. For example, if you want to add the **//iperf //** tool, you can install the related packages and configure LPS8N to use **//iperf //**.

1098

1099

(((

1100

Below are some example **//opkg //** commands. For more information please refer to the [[OPKG package maintain system>>https://oldwiki.archive.openwrt.org/doc/techref/opkg]]** **([[https:~~/~~/oldwiki.archive.openwrt.org/doc/techref/opkg>>https://oldwiki.archive.openwrt.org/doc/techref/opkg]])

)))

(((

**In Linux Console run:**

)))

(((

(% style="color:green" %)**root@dragino-169d30:~~# opkg update** (% style="color:black" %)~/~/ to get the latest packages list

)))

(((

(% style="color:green" %)**root@dragino-169d30:~~# opkg list** (% style="color:black" %) ~/~/shows the available packages

)))

(((

(% style="color:green" %)**root@dragino-169d30:~~# opkg install iperf ** (% style="color:black" %)~/~/ install iperf

1117

)))

1118

1119

The system will automatically install the required packages as shown below.

(((

(% style="background-color:#dcdcdc" %)//root@dragino-169d30:/etc/opkg# opkg install iperf//

)))

(((

(% style="background-color:#dcdcdc" %)//Installing iperf (2.0.12-1) to root…//

)))

(((

(% style="background-color:#dcdcdc" %)//Downloading //[[(% style="background-color: rgb(220, 220, 220); background-color: rgb(220, 220, 220)" %)//http:~~/~~/downloads.openwrt.org/snapshots/packages/mips_24kc/base/iperf_2.0.12-1_mips_24kc.ipk//>>url:http://downloads.openwrt.org/snapshots/packages/mips_24kc/base/iperf_2.0.12-1_mips_24kc.ipk]]

)))

(((

(% style="background-color:#dcdcdc" %)//Installing uclibcxx (0.2.4-3) to root…//

)))

(((

(% style="background-color:#dcdcdc" %)//Downloading //[[(% style="background-color: rgb(220, 220, 220); background-color: rgb(220, 220, 220)" %)//http:~~/~~/downloads.openwrt.org/snapshots/packages/mips_24kc/base/uclibcxx_0.2.4-3_mips_24kc.ipk//>>url:http://downloads.openwrt.org/snapshots/packages/mips_24kc/base/uclibcxx_0.2.4-3_mips_24kc.ipk]]

)))

(((

(% style="background-color:#dcdcdc" %)//Configuring uclibcxx.//

)))

(((

(% style="background-color:#dcdcdc" %)//Configuring iperf.//

)))

= 8. Upgrade Linux Firmware =

1153

1154

1155

We keep improving the LPS8N Linux side firmware for new features and bug fixes. Below are the links for reference.

1156

1157

* **Latest firmware**: [[LoRa Gateway Firmware>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG02-OLG02/Firmware/]],

1158

1159

( [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8N/Firmware>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LIG16/Firmware]])

1160

1161

* **Change Log**: [[Firmware Change Log>>url:http://www.dragino.com/downloads/downloads/LoRa_Gateway/LG02-OLG02/Firmware/ChangeLog]].

1162

1163

( [[http:~~/~~/www.dragino.com/downloads/downloads/LoRa_Gateway/LPS8N/Firmware/ChangeLog>>url:http://www.dragino.com/downloads/downloads/LoRa_Gateway/LIG16/Firmware/ChangeLog]] )

(((

The file named as (% style="color:green" %)** xxxxx–xxxxx-squashfs-sysupgrade.bin **(%%)is the upgrade Image. There are different methods to upgrade, as below.

)))

== 8.1 Upgrade via Web UI ==

(((

Go to the page: (% style="color:green" %)**Web ~-~-> System ~-~-> Firmware Upgrade**

)))

(((

Select the required image and click (% style="color:red" %)**Flash Image.**(%%) The image will be uploaded to the device, and then click (% style="color:red" %)**Process Update**(%%) to upgrade.

)))

(((

(% style="color:red" %)**NOTE**(%%): You normally need to (% style="color:blue" %)**//uncheck//**(%%) the (% style="color:blue" %)//**Preserve Settings**//(%%) checkbox when doing an upgrade to ensure that there is no conflict between the old settings and the new firmware. The new firmware will start up with its default settings.

)))

(((

The system will automatically boot into the new firmware after upgrade.

)))

[[image:1657158986600-386.png]]

1195

1196

1197

== 8.2 Upgrade via Linux console ==

(((

SCP the firmware to the system** (% style="color:green" %)/var(%%)** directory and then run

)))

(((

(% style="color:#4472c4" %)** //root@OpenWrt:~~# /sbin/sysupgrade –n /var/Your_Image//**

)))

(((

(% style="color:red" %)**NOTE**(%%): it is important to transfer the image in the /var directory, otherwise it may exceed the available flash size.

)))

= 9. OTA System Update =

1215

1216

1217

LPS8N supports system auto update via OTA, please see **[[this URL>>url:http://wiki.dragino.com/xwiki/bin/view/OTA%20Update/]]** for the detail of this feature.

= 10. FAQ =

== 10.1 How can I configure for a customized frequency band? ==

(((

See below link for how to customize frequency band: [[How to customized LoRaWAN frequency band>>doc:Main.How to customized LoRaWAN frequency band.WebHome]]

)))

(((

)))

== 10.2 Can I make my own firmware for the gateway, where can I find the source code? ==

(((

Yes, You can make your own firmware for the LPS8N for branding purposes or to add customized applications.

)))

(((

The source code and compile instructions can be found at: [[https:~~/~~/github.com/dragino/openwrt_lede-18.06>>url:https://github.com/dragino/openwrt_lede-18.06]]

)))

(((

)))

== 10.3 Can I use 868Mhz version for 915Mhz bands? ==

1249

1250

1251

It is possible but the distance will be very short, you can select US915 frequency band in 868Mhz version hardware. It will work but you will see the performance is greatly decreased because the 868Mhz version has an RF filter for band 863~~870Mhz, all other frequencies will have high attenuation.

1252

1253

1254

= 11. Trouble Shooting =

1255

1256

== 11.1 I get kernel error when install new package, how to fix? ==

1257

1258

1259

In some cases, when installing a package with **//opkg//**, it will generate a kernel error such as below due to a mismatch I the kernel ID:

1260

1261

(% style="background-color:yellow" %)root@dragino-16c538:~~# opkg install kmod-dragino2-si3217x_3.10.49+0.2-1_ar71xx.ipk

1262

1263

(% style="background-color:yellow" %)Installing kmod-dragino2-si3217x (3.10.49+0.2-1) to root…

1264

1265

(% style="background-color:yellow" %)Collected errors:

1266

1267

(% style="background-color:yellow" %)* satisfy_dependencies_for: Cannot satisfy the following dependencies for kmod-dragino2-si3217x:

1268

1269

(% style="background-color:yellow" %)* kernel (= 3.10.49-1-4917516478a753314254643facdf360a) *

1270

1271

(% style="background-color:yellow" %)* opkg_install_cmd: Cannot install package kmod-dragino2-si3217x.

1272

1273

(((

1274

In this case, you can use the –force-depends option to install such package as long as the actual kernel version is the same.

1275

)))

1276

1277

(% style="background-color:yellow" %)Opkg install kmod-dragino2-si3217x_3.10.49+0.2-1_ar71xx.ipk –force-depends

1278

1279

1280

== 11.2 How to recover the LPS8N if the firmware crashes ==

(((

Please follow this instruction to recover your gateway: [[Recover Gateway>>doc:Main.How to Recover Gateway if can't access it.WebHome]]

)))

(((

)))

== 11.3 I configured LPS8N for WiFi access and lost its IP. What to do now? ==

1292

1293

1294

[[image:1657159323292-776.png]]

(((

The LPS8N has a fall-back IP address on its WAN port. This IP is always enabled so you can use the fall-back IP to access LPS8N no matter what the WiFi IP is. The fall back IP is useful for connecting and debug the unit.

1299

)))

1300

1301

(% style="color:red" %)**Note: fallback IP can be disabled in the WAN and DHCP page.**

1302

1303

1304

**Steps to connect via fall back IP:**

1305

1306

~1. Connect PC's Ethernet port to LG01's WAN port

1307

1308

2. Configure PC's Ethernet port has

1309

IP: 172.31.255.253 and

1310

Netmask: 255.255.255.252

As below photo:

[[image:1652435256286-879.png]]

1316

1317

1318

3. In the PC, use IP address 172.31.255.254 to access the LPS8N via Web or Console.

1319

1320

Please note the latest firmware uses port 8000 for http and 2222 for ssh access.

1321

1322

1323

== 11.4 I connect to the LPS8N's SSID but LPS8N didn't assign DHCP IP to my laptop? ==

(((

This is a known bug for the firmware version before 2019-09-23 for LPS, the issue was fixed since version: LG02_LG08~-~-build-v5.2.1569218466-20190923-1402.

)))

(((

In the old version, user can use the [[fall back ip method >>||anchor="H10.3A0IconfiguredLPS8NforWiFiaccessandlostitsIP.Whattodonow3F"]]to access and configure the device.

)))

= 12. Order Info =

**//PART: (% style="color:blue" %)LPS8N-XXX-YYY//: (%%)**

1339

1340

(% style="color:blue" %) **//XXX~://**(%%)**// Frequency Band//**

1341

1342

* (% style="color:red" %)** 868**(% style="color:black" %) : valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.

1343

* (% style="color:red" %)** 915**(% style="color:black" %): valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920

1344

1345

(% style="color:blue" %) **//YYY~://**(%%)**// 4G Cellular Option//**

1346

1347

* (% style="color:red" %)** EC25-E**(% style="color:black" %): EMEA, Korea, Thailand, India.

1348

* (% style="color:red" %)** EC25-A**(% style="color:black" %): North America/ Rogers/AT&T/T-Mobile.

1349

* (% style="color:red" %)** EC25-AU**(% style="color:black" %): Latin America, New Zeland, Taiwan

1350

* (% style="color:red" %)** EC25-J**(% style="color:black" %): Japan, DOCOMO/SoftBank/ KDDI

1351

1352

More info about valid bands, please see [[EC25-E product page>>url:https://www.quectel.com/product/ec25.htm]].

= 13. Packing Info =

(((

**Package Includes**:

1360

)))

1361

1362

* LPS8N LoRaWAN Gateway x 1

1363

* Stick Antenna for LoRa RF part. Frequency is one of 470 or 868 or 915Mhz depends the model ordered

1364

* Packaging with environmental protection paper box

1365

1366

(((

1367

**Dimension and weight**:

1368

)))

1369

1370

* Device Size: 12 x 12 x 3 cm

1371

* Weight: 187g

1372

* Package Size: 14.5 x 13.5 x 6 cm

* Weight: 300g

= 14. Support =

* Try to see if your questions already answered in the [[wiki>>doc:Main.WebHome]].

1379

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8.

1380

Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before mentioned schedule.

1381

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to:[[support@dragino.com>>url:file:///C:/Users/11315/Documents/D:/Projects/LoRa%20Product%20Line/LG308%20Picocell%20Gateway/LG308/LG308%20%25E8%25AF%25B4%25E6%2598%258E%25E4%25B9%25A6/support@dragino.com]]

1382

1383

Wiki source code of LPS8N - LoRaWAN Gateway User Manual

Applications

Navigation