LPS8N - LoRaWAN Gateway User Manual

The LPS8N is an (% style="color:#4f81bd" %)**open source LoRaWAN Indoor Gateway**(%%). It lets you bridge LoRa wireless network to an IP network via WiFi, Ethernet, 3G or 4G cellular network. The LoRa wireless allows users to send data and reach extremely long ranges at low data-rates.

23

)))

24

25

(((

26

The LPS8N uses (% style="color:#4f81bd" %)**Semtech packet forwarder**(%%) & (% style="color:#4f81bd" %)**LoRaWAN Station connection**(%%) and fully compatible with LoRaWAN protocol. It includes a (% style="color:#4f81bd" %)**SX1302 LoRaWAN concentrator**(%%), which provides 10 programmable parallel demodulation paths.

)))

(((

LPS8N has (% style="color:#4f81bd" %)**pre-configured standard LoRaWAN frequency bands**(%%) to use for different countries. User can also (% style="color:#4f81bd" %)**customized the frequency bands** (%%)to use in their own LoRa network.

)))

(((

LPS8N can communicate with ABP LoRaWAN end node without LoRaWAN server. System integrator can use it to integrate with their existing IoT Service without set up own LoRaWAN server or use 3rd party LoRaWAN service.

)))

(((

)))

[[image:image-20220826090251-1.png]]

42

43

44

== 1.2 Specifications ==

45

46

47

(% style="color:#037691" %)**Hardware System:**

(((

Linux Part:

)))

* 400Mhz ar9331 processor

* 64MB RAM

* 16MB Flash

(% style="color:#037691" %)**Interface:**

58

59

* 10M/100M RJ45 Ports x 1

60

* WiFi : 802.11 b/g/n

61

* LoRaWAN Wireless

62

* Power Input: 5V DC, 2A, Type C

63

* USB 2.0 host connector x 1

64

* Mini-PCI E connector x 1

65

* SX1302 + 2 x SX1250

66

67

(% style="color:#037691" %)**WiFi Spec:**

68

69

* IEEE 802.11 b/g/n

70

* Frequency Band: 2.4 ~~ 2.462GHz

71

* Tx power:

72

** 11n tx power : mcs7/15: 11db mcs0 : 17db

73

** 11b tx power: 18db

74

** 11g 54M tx power: 12db

75

** 11g 6M tx power: 18db

* Wifi Sensitivity

** 11g 54M : -71dbm

** 11n 20M : -67dbm

(% style="color:#037691" %)**LoRa Spec:**

81

82

* Up to -140 dBm sensitivity

83

* 70 dB CW interferer rejection at 1 MHz offset

84

* Able to operate with negative SNR, CCR up to 9dB

85

* Emulates 49 x LoRa demodulators and 1 x (G)FSK demodulator

86

* Dual digital TX & RX radio front-end interfaces

87

* 10 programmable parallel demodulation paths

88

* Dynamic data-rate (DDR) adaptation

89

* True antenna diversity or simultaneous dual-band operation

90

91

(% style="color:#037691" %)**Cellular 4G LTE (optional):**

92

93

* Quectel [[**EC25 LTE module**>>url:https://www.quectel.com/product/ec25minipcie.htm]]

94

* Micro SIM Slot

95

* External 4G Sticker Antenna.

96

* Up to 150Mbps downlink and 50Mbps uplink data rates

97

* Worldwide LTE,UMTS/HSPA+ and GSM/GPRS/EDGE coverage

98

* MIMO technology meets demands for data rate and link reliability in modem wireless communication systems

== 1.3 Features ==

* Open Source OpenWrt system

105

* Managed by Web GUI, SSH via WAN or WiFi

106

* Remote access with Reverse-SSH or remote.it

107

* Emulates 49x LoRa demodulators

108

* LoRaWAN Gateway

109

* 10 programmable parallel demodulation paths

110

* Pre-configure to support different LoRaWAN regional settings.

111

* Allow to customize LoRaWAN regional parameters.

112

* Support Local decode ABP end node info and transfer to MQTT server

113

* Support different level log in.

114

* Support Semtech Packet Forwarder

115

* Support LoRaWAN basic station.

116

* Optional 3G/4G cellular connection

117

118

119

== 1.4 Hardware System Structure ==

120

121

122

[[image:image-20220830153228-1.png]]

123

124

125

== 1.5 LPS8N Applications ==

126

127

128

[[image:1657079055940-721.png]]

129

130

131

== 1.6 LED Indicators ==

132

133

134

LPS8N has totally four LEDs, They are:

135

136

* **Power LED **[[image:image-20220706115518-1.png||height="15" width="16"]] : This (% style="color:red" %)**RED LED**(%%) will be **solid on** if the device is properly powered.

137

* **Wireless LED** [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/LG308N%20-%20LoRaWAN%20Gateway%20User%20Manual/WebHome/image-20220705165446-6.png?width=15&height=15&rev=1.1||alt="image-20220705165446-6.png" height="15" width="15"]]: No function yet.

138

* **SYS LED ** [[image:image-20220706115518-3.png||height="16" width="16"]] : This **RGB LED** will shows different colors on different state:

139

** (% style="color:blue" %)**SOLID BLUE**(%%): Device is alive with LoRaWAN server connection.

140

** (% style="color:blue" %)**BLINKING BLUE**(%%): a) Device has internet connection but no LoRaWAN Connection. or b) Device is in booting stage, in this stage, it will (% style="color:blue" %)**BLINKING BLUE**(%%) for several seconds and then with (% style="color:red" %)**SOLID RED**(%%) and (% style="color:blue" %)**BLINKING BLUE**(%%) together

141

** (% style="color:red" %)**SOLID RED**(%%): Device doesn't have Internet connection.

142

143

* **ETH LED **[[image:image-20220706115518-4.png||height="15" width="17"]] : This LED shows the ETH interface connection status.

144

145

146

== 1.7 Button Instruction ==

147

148

149

LPS8N has a black toggle button, which is:

150

151

152

(% style="color:blue" %)**//➢ //Long press 4-5s: **(%%)the gateway will reload the Network and Initialize wifi configuration

153

154

**LED status: ** SYS LED will BLINKING BLUE Until the reload is finished.

155

156

157

(% style="color:blue" %)**➢ Long press more than 30s: **(%%)the gateway will restart and restore factory settings.

158

159

**LED status: ** When the user releases the button, the LED will TURN OFF.

160

161

162

= 2. Access and Configure LPS8N =

(((

The LPS8N is configured as a WiFi Access Point by factory default. You can access and configure the LPS8N after connecting to its WiFi network, or via its WAN Ethernet port.

)))

== 2.1 Find IP address of LPS8N ==

171

172

=== 2.1.1 Connect via WiFi ===

173

174

175

[[image:1657085974260-168.png]]

176

177

178

At the first boot of LPS8N, it will auto generate a WiFi network called (% style="color:green" %)**//dragino-xxxxxx //**(% style="color:black" %)with password: (% style="background-color:yellow" %)dragino+dragino

179

180

181

[[image:1652413127647-377.png]]

(((

User can use a PC to connect to this WiFi network. The PC will get an IP address 10.130.1.xxx and the DLOS8N has the default IP (% style="color:green" %)10.130.1.1

)))

=== 2.1.2 Connect via Ethernet with DHCP IP from router ===

191

192

193

[[image:1657086105922-299.png]]

(((

Alternatively, connect the LPS8N Ethernet port to your router and LPS8N will obtain an IP address from your router. In the router's management portal, you should be able to find what IP address the router has assigned to the LPS8N. You can also use this IP to connect.

)))

=== 2.1.3 Connect via WiFi with DHCP IP from router ===

203

204

205

[[image:1657086192720-649.png]]

206

207

208

If the LPS8N already connect to the router via WiFi, use can use the WiFi IP to connect to LPS8N.

209

210

211

=== 2.1.4 Connect via Ethernet with fall back ip ===

212

213

214

The WAN port also has a [[fall back ip address>>||anchor="H10.3A0IconfiguredLPS8NforWiFiaccessandlostitsIP.Whattodonow3F"]] for access if user doesn't connect to uplink router. Click [[here>>||anchor="H10.3A0IconfiguredLPS8NforWiFiaccessandlostitsIP.Whattodonow3F"]] to see how to configure.

215

216

217

== 2.2 Access Configure Web UI ==

**Web Interface**

Open a browser on the PC and type the LPS8N ip address (depends on your connect method)

223

224

[[http:~~/~~/10.130.1.1/>>url:http://10.130.1.1/]] (Access via WiFi AP network)

or

http:~/~/IP_ADDRESS or [[http:~~/~~/ IP_ADDRESS:8000>>url:http://192.168.1.xx:8000]]

229

230

231

You will see the login interface of LPS8N as shown below.

232

233

The account details for Web Login are:

234

235

(% style="color:#4f81bd" %)**User Name: root**

236

237

(% style="color:#4f81bd" %)**Password: dragino**

238

239

[[image:1652414287022-223.png]]

240

241

242

= 3. Typical Network Setup =

== 3.1 Overview ==

The LPS8N supports flexible network set up for different environments. This section describes the typical network topology. The network set up includes:

248

249

* **WAN Port Internet Mode**

250

* **WiFi Client Mode**

* **WiFi AP Mode**

== 3.2 Use WAN port to access Internet ==

255

256

257

By default, the LPS8N is set to use the WAN port to connect to an upstream network. When you connect the LPS8N's WAN port to an upstream router, LPS8N will get an IP address from the router and have Internet access via the upstream router. The network status can be checked in the (% style="color:#4f81bd" %)**home page**:

258

259

260

[[image:1657088560833-398.png]]

261

262

263

== 3.3 Access the Internet as a WiFi Client ==

264

265

266

In the WiFi Client Mode, LPS8N acts as a WiFi client and gets DHCP from an upstream router via WiFi.

267

268

(((

269

The settings for WiFi Client is under page (% style="color:#4f81bd" %)**System~-~-> WiFi ~-~-> WiFi WAN Client Settings**

270

271

272

[[image:1657088818095-182.png]]

)))

(((

In the WiFi Survey Choose the WiFi AP, and input the Passphrase then click Save & Apply to connect.

)))

== 3.4 Use built-in 4G modem for internet access ==

(((

(((

If the LPS8N has 3G/4G Cellular modem, user can use it as main internet connection or back up.

)))

(((

First, install the Micro SIM card as below direction

)))

(((

Second, Power off/ ON LPS8N to let it detect the SIM card.

)))

)))

[[image:1657090855037-497.png]]

(((

)))

(((

The set up page is (% style="color:#4f81bd" %)**System ~-~-> Cellular**

)))

(((

While use the cellular as Backup WAN, device will use Cellular for internet connection while WAN port or WiFi is not valid and switch back to WAN port or WiFi after they recover.

)))

(((

[[image:1657090932270-444.png]]

)))

== 3.5 Check Internet connection ==

323

324

325

In the (% style="color:#4f81bd" %)**home**(%%) page, we can check the Internet connection.

326

327

* GREEN Tick [[image:1652436675869-206.png||height="14" width="15"]] : This interface has Internet connection.

328

* Yellow Tick [[image:1652436705761-420.png||height="15" width="15"]] : This interface has IP address but don't use it for internet connection.

329

* RED Cross [[image:1652436787176-950.png||height="14" width="15"]] : This interface doesn't connected.

330

331

[[image:1657091099235-452.png]]

332

333

334

= 4. Example: Configure as a LoRaWAN gateway =

335

336

337

LPS8N is fully compatible with LoRaWAN protocol. It uses the legacy Semtech Packet forwarder to forward the LoRaWAN packets to server. The structure is as below.

(((

[[image:image-20220826090251-1.png]]

)))

(((

This chapter describes how to use the LPS8N to work with (TTN v3)[[ LoRaWAN Server>>url:https://www.thethingsnetwork.org/]] ([[www.thethingsnetwork.org>>url:http://www.thethingsnetwork.org/]])

)))

== 4.1 Create a gateway in TTN V3 Server ==

350

351

352

(% style="color:blue" %)**Step 1: Get a Unique gateway ID.**

(((

Every LPS8N has a unique gateway id. The ID can be found at LoRaWAN page:

)))

(((

[[image:1657091583941-544.png]]

)))

The example gateway id is: (% style="color:green" %)**a840411e96744154**

(% style="color:blue" %)**Step 2: Sign up a user account in TTN server**

372

373

374

[[**https:~~/~~/account.thethingsnetwork.org/register**>>url:https://account.thethingsnetwork.org/register]]

375

376

377

[[image:1657091739530-531.png]]

(% style="color:blue" %)**Step 3: Choose the TTNv3 Cluster Picker**

(((

[[image:1657091719947-297.png]]

)))

(% style="color:red" %)**Note: Choose the cluster corresponds to a specific Gateway server address**

391

392

393

* Europe 1** (% style="color:red" %)corresponding Gateway server address:(%%)**(% style="color:red" %) (% style="color:black" %)eu1.cloud.thethings.network

394

* North America 1 (% style="color:red" %)**corresponding Gateway server address: **(% style="color:black" %)nam1.cloud.thethings.network

395

* Australia 1 (% style="color:red" %)**corresponding Gateway server address: **(% style="color:black" %)au1.cloud.thethings.network

396

* Legacy V2 Console : (% style="color:red" %)**TTN v2 shuts down in December 2021**

397

398

399

(% style="color:blue" %)**Step 4: Create a Gateway**

400

401

402

[[image:1657091941182-367.png]]

403

404

Click the Gateway icon and then click Add gateway.

405

406

407

Open the following page:

408

409

410

[[image:image-20220706155323-5.png||height="579" width="1060"]]

411

412

413

[[image:image-20220706155323-6.png||height="582" width="1066"]]

(((

(% style="color:red" %)**Notice: Gateway Server address must match the gateway configuration, otherwise you will have problem for End Node to join the network.**

)))

After creating the gateway, you can see the gateway info, as below.

423

424

[[image:1657094130908-567.png]](% style="display:none" %)

425

426

427

== 4.2 Configure LPS8N to connect to TTN v3 ==

(((

You can now configure the LPS8N to let it connect to TTN network V3.

)))

(((

Make sure your LPS8N has a working Internet Connection first.

)))

(((

Choose the right server provider and click (% style="color:#4f81bd" %)**Save&Apply.**

)))

[[image:1657094183213-301.png]]

445

446

447

(% style="color:red" %)**Note: The server address must match the Gateway server address you choose in TTN V3.**

448

449

450

In the home page, we can see the LoRaWAN connection is ready now.

451

452

453

[[image:1657094202420-798.png]]

In TTN v3 portal, we can also see the gateway is connected.

458

459

[[image:1657094221515-510.png]]

460

461

462

== 4.3 Configure frequency ==

463

464

465

We also need to set the frequency plan in LPS8N to match the end node we use, so to receive the LoRaWAN packets from the LoRaWAN sensor.

466

467

468

[[image:1657094249818-468.png]]

In logread page, user can check the frequency actually used.

473

474

[[image:1657094333704-207.png]]

475

476

477

== 4.4 Add a LoRaWAN End Device ==

(((

This section shows how to add a LoRaWAN End device to a LoRaWAN network and see the data from TTN web site.

)))

(((

We use [[LT-22222-L>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/156-lt-22222-l.html]] IO Controller as a reference device - the setup for other LoRaWAN devices will be similar.

486

)))

487

488

[[image:1652422794767-871.png]]

(((

(% style="color:blue" %)**Step 1**: (%%)Create a Device definition in TTN v3 with the OTAA keys from the example LT-22222-L IO Controller device.

)))

(((

Three codes are required to define the device in TTN v3:

499

)))

500

501

* DEV EUI - Unique ID code for a particular device.

502

* APP EUI - ID code for an Application defined in TTN v3.

503

* APP Key - Unique key to secure communications with a particular device.

504

505

(((

506

A set of these codes are stored in each device by the manufacturer as the default codes for that particular device. Each device is shipped with a sticker with the default Device EUI as shown below.

)))

[[image:1657094382177-591.png]]

(((

(% style="color:red" %)**Note: You may be able to change these codes in a device by using a configuration facility on the device e.g. the LT-22222 uses a serial port access and a series of AT commands. Changing the codes may be necessary in the case where you have to use codes assigned by a LoRa WAN server.**

)))

(((

For the TTN v3 server, you can use the codes set in the device as in the following example.

)))

(((

Select **Add Application** to open the screen below.

)))

[[image:1657094417175-831.png]]

531

532

Open the **Application **select** Add end device**

533

534

535

Start Register the end device

536

537

[[image:1657094444802-101.png]]

538

539

(((

540

Select OTAA activation mode

)))

(((

The LoRaWAN version for your device should be provided by the manufacturer in a datasheet as LoRaWAN version or LoRaWAN specification. The most commonly used LoRaWAN versions are v1.0.2 and v1.0.3.

547

)))

548

549

[[image:1657094475730-208.png]]

550

551

First, input the End device ID, AppEUI and DevEUI.

552

553

554

[[image:1657094646429-966.png]]

555

556

Secondly, choose the corresponding frequency and LoRaWAN class capabilities.

557

558

559

[[image:1657094674045-755.png]]

560

561

(((

562

Finally, Application layer settings input the corresponding AppKey. Before saving the configuration, check that the data matches the device.

)))

(((

(% style="color:blue" %)**Step 2**: (%%)Power on LT-22222-L device and it will automatically join the TTN network. After joining successfully, it will start to upload messages to the TTN v3. Select the Live data tab and you will see the data appearing in the panel.

)))

(((

(% style="color:red" %)**Note that it may take some time for the device data to appear in the TTN v3 display.**

)))

[[image:1657094791060-639.png]]

580

581

582

= 5. Web Configure Pages =

== 5.1 Home ==

Shows the system running status.

588

589

590

[[image:1657094893942-726.png]]

591

592

593

== 5.2 LoRa Settings ==

594

595

=== 5.2.1 LoRa ~-~-> LoRa ===

(((

This page shows the LoRa Radio Settings. There are a set of default frequency band according to LoRaWAN protocol, and user can customized the band* as well.

)))

(((

Different LPS8N hardware version can support different frequency range:

604

)))

605

606

* (% style="color:blue" %)**868**(%%): valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.

607

* (% style="color:blue" %)**915**(%%): valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920

(((

(((

After user choose the frequency plan, he can see the actually frequency in used by checking the page (% style="color:green" %)**LogRead ~-~-> LoRa Log**

)))

)))

[[image:1657094930903-357.png]]

620

621

(% style="color:red" %)**Note *:** **[[See this instruction for how to customize frequency band>>doc:Main.How to customized LoRaWAN frequency band.WebHome]]**

622

623

624

=== 5.2.2 LoRa ~-~-> ABP Decryption ===

625

626

627

The LPS8N can communicate with LoRaWAN ABP End Node without the need of LoRaWAN server. It can be used in some cases such as:

628

629

* No internet connection.

630

* User wants to get data forward in gateway and forward to their server based on MQTT/HTTP, etc. (Combine ABP communication method and [[MQTT forward together>>doc:Main.MQTT Forward Instruction.WebHome]]).

631

632

(((

633

Detail of this feature: **[[Communication with ABP End Node>>doc:Main.Communicate with ABP End Node without LoRaWAN Network Server --- LG308.WebHome]]**

)))

[[image:1657095412271-942.png]]

639

640

641

== 5.3 LoRaWAN Settings ==

642

643

=== 5.3.1 LoRaWAN ~-~-> LoRaWAN ===

644

645

646

This page is for the connection set up to a general LoRaWAN Network server such as: [[TTN>>url:http://www.thethingsnetwork.org/]], [[ChirpStack>>url:https://www.chirpstack.io/]] etc.

647

648

649

[[image:1652423628833-467.png||height="357" width="755"]]

650

651

652

(% style="color:red" %)**Note:**

653

654

~*: User can ignore the latitude and longitude settings here, LPS8N will use the actually value from GPS module.

655

656

~**: Packet filter is to drop the unwanted LoRaWAN packet, instruction see here:

657

658

**See:** **[[Filter unwanted LoRaWAN packets>>doc:Main.Filter unwanted LoRaWAN packets.WebHome]]**

659

660

661

=== 5.3.2 LoRaWAN ~-~-> Amazon AWS-IoT ===

662

663

664

[[image:1652428499323-384.png||height="275" width="723"]]

(((

Please see this instruction to know more detail and demo for how to connect to **[[AWS-IoT LoRaWAN Core>>doc:Main.AWS IoT Core for LoRaWAN.WebHome]].**

)))

=== 5.3.3 LoRaWAN ~-~-> LORIOT ===

(((

Settings to communicate to LORIOT LoRaWAN Network Server: [[https:~~/~~/www.loriot.io/>>url:https://www.loriot.io/]]

)))

(((

Instruction: **[[Notes for LORIOT>>doc:Main.Notes for LORIOT.WebHome]]**

)))

[[image:1652428648903-878.png||height="266" width="731"]]

687

688

689

== 5.4 MQTT Settings ==

(((

If end nodes works in ABP mode, user can configure LPS8N to transfer the data to MQTT broker,

)))

(((

Instruction: **[[MQTT Forward Instruction>>doc:Main.MQTT Forward Instruction.WebHome]]**

)))

[[image:1652428705046-212.png||height="417" width="733"]]

== 5.5 System ==

=== 5.5.1 System ~-~-> System Overview ===

707

708

709

Shows the system info:

710

711

712

[[image:image-20220826091810-6.png]]

713

714

715

=== 5.5.2 System ~-~-> General ( login settings) ===

716

717

718

[[image:1657155183982-792.png]]

(((

(% style="color:#037691" %)**__System Password:__**

)))

(((

There are two login for LPS8N: (% style="color:blue" %)**root /dragino** (%%)or (% style="color:blue" %)**admin /dragino**. (%%)Both root and admin has the same right for WEB access. But root user has also the right to access via SSH to Linux system. admin only able to access WEB interface.

)))

(((

This page can be used to set the password for them.

)))

(((

(% style="color:#037691" %)**__Timezone: __**(%%)Set device timezone.

)))

(((

(% style="color:#037691" %)**__Port forwarding: __**(%%)Enable/Disable the HTTP and SSH access via WAN interface.

)))

=== 5.5.3 System ~-~-> Network ===

744

745

746

[[image:1657155288223-566.png]]

(((

(% style="color:#037691" %)**__LAN Settings: __**(%%)When the LPS8N has the AP enable, LAN settings specify the network info for LPS8N's own network.

)))

(((

(% style="color:#037691" %)__**WAN Settings: **__(%%)Setting for LPS8N WAN port

)))

(((

(% style="color:#037691" %)__**WiFi Settings: **__** **(%%)Setting for LPS8N WiFi IP when use it as WiFi Client

)))

=== 5.5.4 System ~-~-> WiFi ===

LPS8N WiFi Settings.

[[image:1657155457089-430.png]]

770

771

772

=== 5.5.5 System ~-~-> Cellular ===

773

774

775

While use the cellular as Backup WAN, device will use Cellular for internet connection while WAN port or WiFi is not valid and switch back to WAN port or WiFi after they recover.

776

777

778

[[image:1657155507672-204.png]]

779

780

781

(% style="color:red" %)**Note *: For LPS8N which doesn't have the cellular module, this page will shows Cellular not detected.**

782

783

784

=== 5.5.6 System ~-~-> Network Status ===

785

786

787

[[image:1657155554265-721.png]]

788

789

790

=== 5.5.7 System ~-~-> Remote Mgnt & Auto Provision ===

791

792

793

Auto Provision is the feature for batch configure and remote management. It can be used in below two cases:

794

795

796

[[image:image-20220707112053-4.png||height="451" width="995"]]

797

798

[[image:image-20220707112053-5.png||height="453" width="1004"]]

799

800

(% style="display:none" %)

801

802

(% style="display:none" %) [[image:1657157402578-508.png||height="450" width="992"]]

803

804

(% id="cke_bm_589629S" style="display:none" %) [[image:image-20220707092040-2.png||height="452" width="1002"]]

805

806

[[image:image-20220826091725-5.png||height="479" width="1004"]]

(((

Please see this document for detail: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8N/Firmware/Application_Note/&file=Auto-update-feature.pdf>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Application_Note/&file=Auto-update-feature.pdf]]

811

)))

812

813

(% style="display:none" %) (%%)

814

815

(((

816

R-SSH is for remote access device and management, introduction for how to use: [[Remote Access Gateway>>doc:Main.Monitor & Remote Access Gateway.WebHome]]

)))

[[image:1652429624400-864.png||height="432" width="716"]]

822

823

824

=== 5.5.8 System ~-~-> Firmware Upgrade ===

825

826

827

We keep improving the LPS8N Linux side firmware for new features and bug fixes. Below are the links for reference.

828

829

* **Latest firmware**: [[LoRa Gateway Firmware>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG02-OLG02/Firmware/]],

830

831

( [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8N/Firmware>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LIG16/Firmware]])

832

833

* **Change Log**: [[Firmware Change Log>>url:http://www.dragino.com/downloads/downloads/LoRa_Gateway/LG02-OLG02/Firmware/ChangeLog]].

834

835

( [[http:~~/~~/www.dragino.com/downloads/downloads/LoRa_Gateway/LPS8N/Firmware/ChangeLog>>url:http://www.dragino.com/downloads/downloads/LoRa_Gateway/LIG16/Firmware/ChangeLog]] )

(((

The file named as (% style="color:green" %)**xxxxx–xxxxx-squashfs-sysupgrade.bin **(% style="color:black" %)is the upgrade Image. There are different methods to upgrade, as below.

)))

(((

(% style="color:green" %)**Web~-~-> System~-~-> Firmware Upgrade**

)))

[[image:1657156052651-770.png]]

(((

Select the required image and click (% style="color:blue" %)**Flash Image.**(%%) The image will be uploaded to the device, and then click (% style="color:blue" %)**Process Update**(%%) to upgrade.

)))

(((

(% style="color:red" %)**NOTE**: (%%)You normally need to (% style="color:blue" %)**//uncheck//**(%%) the (% style="color:blue" %)**Preserve Settings**(%%) checkbox when doing an upgrade to ensure that there is no conflict between the old settings and the new firmware. The new firmware will start up with its default settings.

)))

(((

The system will automatically boot into the new firmware after upgrade.

)))

[[image:1657156094153-520.png]]

869

870

871

(% style="color:red" %)**NOTE***(%%): User can also upgrade firmware via Linux console

872

873

SCP the firmware to the system(% style="color:green" %)**/var**(%%)** **directory and then run

874

875

(% style="color:#4f81bd" %)**//root@OpenWrt:~~# /sbin/sysupgrade –n /var/Your_Image//**

876

877

878

(% style="color:red" %)**NOTE**(%%) : it is important to transfer the image in the /var directory, otherwise it may exceed the available flash size.

879

880

881

=== 5.5.9 System ~-~-> Reboot/Reset ===

882

883

884

[[image:1652430197132-330.png||height="256" width="724"]]

(((

)))

=== 5.5.10 System ~-~-> Package Maintain ===

891

892

893

[[image:1657156199070-491.png]]

894

895

896

Place to show what package has installed and possible to upgrade packages.

== 5.6 LogRead ==

=== 5.6.1 LogRead ~-~-> LoRa Log ===

902

903

904

Show the frequency for LoRa Radio and traffics.

905

906

907

[[image:1657156300781-933.png]]

908

909

910

=== 5.6.2 LogRead ~-~-> System Log ===

Show the system log

[[image:1657156341198-226.png]]

= 6. More features =

== 6.1 Packet Filtering ==

(((

Drop unwanted packets.

)))

(((

See: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Filter%20unwanted%20LoRaWAN%20packets/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Filter%20unwanted%20LoRaWAN%20packets/]]

)))

== 6.2 Remote Access ==

(((

Remote Access Devices for management.

)))

(((

Instruction: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Monitor%20%26%20Remote%20Access%20Gateway/?Remote%20Access>>http://wiki.dragino.com/xwiki/bin/view/Main/Monitor%20%26%20Remote%20Access%20Gateway/?Remote%20Access]]

)))

== 6.3 How to decode ABP LoRaWAN node ==

(((

Decode ABP:

)))

(((

[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Communicate%20with%20ABP%20End%20Node%20without%20LoRaWAN%20Network%20Server%20~~-~~--%20LG308/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Communicate%20with%20ABP%20End%20Node%20without%20LoRaWAN%20Network%20Server%20---%20LG308/]]

)))

== 6.4 How to set data to MQTT broker ==

(((

Only support ABP LoRaWAN End Node

)))

(((

Instruction: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/MQTT%20Forward%20Instruction/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/MQTT%20Forward%20Instruction/]]

)))

== 6.5 More instructions ==

970

971

972

[[LoRaWAN Gateway Instruction>>doc:Main.WebHome]](LoRaWAN Gateway)

973

974

975

== 6.6 Auto-Provision ==

976

977

978

Auto Provision is the feature for batch configure and remote management. It can be used in below two cases:

979

980

[[image:image-20220707092040-1.png||height="451" width="995"]]

981

982

[[image:image-20220707092040-2.png||height="452" width="1002"]]

983

984

[[image:image-20220826091546-4.png]](% style="display:none" %)

(((

Please see this document for detail: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8N/Firmware/Application_Note/&file=Auto-update-feature.pdf>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Application_Note/&file=Auto-update-feature.pdf]]

989

)))

990

991

(% style="display:none" %) (%%)

992

993

= 7. (% style="display:none" %) (%%)Linux System =

994

995

996

The LPS8N is based on the OpenWrt Linux system. It is open source, and users are free to configure and modify the Linux settings.

997

998

(% style="display:none" %) (%%)

999

1000

== 7.1 SSH Access for Linux console ==

1001

1002

1003

User can access the Linux console via the SSH protocol. Make sure your PC and the LPS8N are connected to the same network, then use a SSH tool (such as [[putty>>url:http://www.chiark.greenend.org.uk/~~sgtatham/putty/download.html]] in Windows) to access it.

1004

1005

IP address: IP address of LPS8N

1006

1007

Port: 22 (via WiFi AP mode) or 2222 (via WAN Interface)

1008

1009

User Name: (% style="color:green" %)**root**

1010

1011

Password: (% style="color:green" %)**dragino** (% style="color:black" %)(default)

1012

1013

After logging in, you will be in the Linux console and can enter commands as shown below.

1014

1015

1016

[[image:1657158198733-338.png]]

1017

1018

1019

The “** (% style="background-color:yellow" %)logread -f(%%)**(% style="background-color:yellow" %)” (%%)command can be used to debug how system runs.

1020

1021

1022

[[image:1657158190234-805.png]]

1023

1024

1025

== 7.2 Edit and Transfer files ==

(((

The LPS8N supports the (% style="color:green" %)**SCP protocol** (% style="color:black" %)and has a built-in (% style="color:green" %)**SFTP server**. (% style="color:black" %)There are many ways to edit and transfer files using these protocols.

)))

(((

In Windows, one of the easiest methods is using the [[WinSCP>>url:https://winscp.net/eng/index.php]] utility.

)))

(((

After establishing access via WinSCP to the device, you can use an FTP style window to drag / drop files to the LPS8N, or edit the files directly in the windows.

)))

(((

Screenshot is as below:

1042

)))

1043

1044

[[image:1652431650755-450.png]]

1045

1046

1047

== 7.3 File System ==

(((

The LPS8N has a 16MB flash and a 64MB RAM. The /var and /tmp directories are in the RAM, so contents stored in /tmp and /var will be erased after rebooting the device. Other directories are in the flash and will remain after reboot.

)))

(((

The Linux system uses around 8MB ~~10MB flash size which means there is not much room for user to store data in the LPS8N flash.

)))

(((

You can use an external USB flash memory device to extend the size of flash memory for storage.

)))

== 7.4 Package maintenance system ==

1064

1065

1066

LPS8N uses the OpenWrt [[**OPKG package maintenance system**>>https://oldwiki.archive.openwrt.org/doc/techref/opkg]]. There are more than 3000+ packages available in our package server for users to install for their applications. For example, if you want to add the **//iperf //** tool, you can install the related packages and configure LPS8N to use **//iperf //**.

1067

1068

(((

1069

Below are some example **//opkg //** commands. For more information please refer to the [[OPKG package maintain system>>https://oldwiki.archive.openwrt.org/doc/techref/opkg]]** **([[https:~~/~~/oldwiki.archive.openwrt.org/doc/techref/opkg>>https://oldwiki.archive.openwrt.org/doc/techref/opkg]])

)))

(((

**In Linux Console run:**

)))

(((

(% style="color:green" %)**root@dragino-169d30:~~# opkg update** (% style="color:black" %)~/~/ to get the latest packages list

)))

(((

(% style="color:green" %)**root@dragino-169d30:~~# opkg list** (% style="color:black" %) ~/~/shows the available packages

)))

(((

(% style="color:green" %)**root@dragino-169d30:~~# opkg install iperf ** (% style="color:black" %)~/~/ install iperf

1086

)))

1087

1088

The system will automatically install the required packages as shown below.

(((

(% style="background-color:#dcdcdc" %)//root@dragino-169d30:/etc/opkg# opkg install iperf//

)))

(((

(% style="background-color:#dcdcdc" %)//Installing iperf (2.0.12-1) to root…//

)))

(((

(% style="background-color:#dcdcdc" %)//Downloading //[[(% style="background-color: rgb(220, 220, 220); background-color: rgb(220, 220, 220)" %)//http:~~/~~/downloads.openwrt.org/snapshots/packages/mips_24kc/base/iperf_2.0.12-1_mips_24kc.ipk//>>url:http://downloads.openwrt.org/snapshots/packages/mips_24kc/base/iperf_2.0.12-1_mips_24kc.ipk]]

)))

(((

(% style="background-color:#dcdcdc" %)//Installing uclibcxx (0.2.4-3) to root…//

)))

(((

(% style="background-color:#dcdcdc" %)//Downloading //[[(% style="background-color: rgb(220, 220, 220); background-color: rgb(220, 220, 220)" %)//http:~~/~~/downloads.openwrt.org/snapshots/packages/mips_24kc/base/uclibcxx_0.2.4-3_mips_24kc.ipk//>>url:http://downloads.openwrt.org/snapshots/packages/mips_24kc/base/uclibcxx_0.2.4-3_mips_24kc.ipk]]

)))

(((

(% style="background-color:#dcdcdc" %)//Configuring uclibcxx.//

)))

(((

(% style="background-color:#dcdcdc" %)//Configuring iperf.//

)))

= 8. Upgrade Linux Firmware =

1122

1123

1124

We keep improving the LPS8N Linux side firmware for new features and bug fixes. Below are the links for reference.

1125

1126

* **Latest firmware**: [[LoRa Gateway Firmware>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG02-OLG02/Firmware/]],

1127

1128

( [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8N/Firmware>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LIG16/Firmware]])

1129

1130

* **Change Log**: [[Firmware Change Log>>url:http://www.dragino.com/downloads/downloads/LoRa_Gateway/LG02-OLG02/Firmware/ChangeLog]].

1131

1132

( [[http:~~/~~/www.dragino.com/downloads/downloads/LoRa_Gateway/LPS8N/Firmware/ChangeLog>>url:http://www.dragino.com/downloads/downloads/LoRa_Gateway/LIG16/Firmware/ChangeLog]] )

(((

The file named as (% style="color:green" %)** xxxxx–xxxxx-squashfs-sysupgrade.bin **(%%)is the upgrade Image. There are different methods to upgrade, as below.

)))

== 8.1 Upgrade via Web UI ==

(((

Go to the page: (% style="color:green" %)**Web ~-~-> System ~-~-> Firmware Upgrade**

)))

(((

Select the required image and click (% style="color:red" %)**Flash Image.**(%%) The image will be uploaded to the device, and then click (% style="color:red" %)**Process Update**(%%) to upgrade.

)))

(((

(% style="color:red" %)**NOTE**(%%): You normally need to (% style="color:blue" %)**//uncheck//**(%%) the (% style="color:blue" %)//**Preserve Settings**//(%%) checkbox when doing an upgrade to ensure that there is no conflict between the old settings and the new firmware. The new firmware will start up with its default settings.

)))

(((

The system will automatically boot into the new firmware after upgrade.

)))

[[image:1657158986600-386.png]]

1164

1165

1166

== 8.2 Upgrade via Linux console ==

(((

SCP the firmware to the system** (% style="color:green" %)/var(%%)** directory and then run

)))

(((

(% style="color:#4472c4" %)** //root@OpenWrt:~~# /sbin/sysupgrade –n /var/Your_Image//**

)))

(((

(% style="color:red" %)**NOTE**(%%): it is important to transfer the image in the /var directory, otherwise it may exceed the available flash size.

)))

= 9. OTA System Update =

1184

1185

1186

LPS8N supports system auto update via OTA, please see **[[this URL>>url:http://wiki.dragino.com/xwiki/bin/view/OTA%20Update/]]** for the detail of this feature.

= 10. FAQ =

== 10.1 How can I configure for a customized frequency band? ==

(((

See below link for how to customize frequency band: [[How to customized LoRaWAN frequency band>>doc:Main.How to customized LoRaWAN frequency band.WebHome]]

)))

(((

)))

== 10.2 Can I make my own firmware for the gateway, where can I find the source code? ==

(((

Yes, You can make your own firmware for the LPS8N for branding purposes or to add customized applications.

)))

(((

The source code and compile instructions can be found at: [[https:~~/~~/github.com/dragino/openwrt_lede-18.06>>url:https://github.com/dragino/openwrt_lede-18.06]]

)))

(((

)))

== 10.3 Can I use 868Mhz version for 915Mhz bands? ==

1218

1219

1220

It is possible but the distance will be very short, you can select US915 frequency band in 868Mhz version hardware. It will work but you will see the performance is greatly decreased because the 868Mhz version has an RF filter for band 863~~870Mhz, all other frequencies will have high attenuation.

1221

1222

1223

= 11. Trouble Shooting =

1224

1225

== 11.1 I get kernel error when install new package, how to fix? ==

1226

1227

1228

In some cases, when installing a package with **//opkg//**, it will generate a kernel error such as below due to a mismatch I the kernel ID:

1229

1230

(% style="background-color:yellow" %)root@dragino-16c538:~~# opkg install kmod-dragino2-si3217x_3.10.49+0.2-1_ar71xx.ipk

1231

1232

(% style="background-color:yellow" %)Installing kmod-dragino2-si3217x (3.10.49+0.2-1) to root…

1233

1234

(% style="background-color:yellow" %)Collected errors:

1235

1236

(% style="background-color:yellow" %)* satisfy_dependencies_for: Cannot satisfy the following dependencies for kmod-dragino2-si3217x:

1237

1238

(% style="background-color:yellow" %)* kernel (= 3.10.49-1-4917516478a753314254643facdf360a) *

1239

1240

(% style="background-color:yellow" %)* opkg_install_cmd: Cannot install package kmod-dragino2-si3217x.

1241

1242

(((

1243

In this case, you can use the –force-depends option to install such package as long as the actual kernel version is the same.

1244

)))

1245

1246

(% style="background-color:yellow" %)Opkg install kmod-dragino2-si3217x_3.10.49+0.2-1_ar71xx.ipk –force-depends

1247

1248

1249

== 11.2 How to recover the LPS8N if the firmware crashes ==

(((

Please follow this instruction to recover your gateway: [[Recover Gateway>>doc:Main.How to Recover Gateway if can't access it.WebHome]]

)))

(((

)))

== 11.3 I configured LPS8N for WiFi access and lost its IP. What to do now? ==

1261

1262

1263

[[image:1657159323292-776.png]]

(((

The LPS8N has a fall-back IP address on its WAN port. This IP is always enabled so you can use the fall-back IP to access LPS8N no matter what the WiFi IP is. The fall back IP is useful for connecting and debug the unit.

1268

)))

1269

1270

(% style="color:red" %)**Note: fallback IP can be disabled in the WAN and DHCP page.**

1271

1272

1273

**Steps to connect via fall back IP:**

1274

1275

~1. Connect PC's Ethernet port to LG01's WAN port

1276

1277

2. Configure PC's Ethernet port has

1278

IP: 172.31.255.253 and

1279

Netmask: 255.255.255.252

As below photo:

[[image:1652435256286-879.png]]

1285

1286

1287

3. In the PC, use IP address 172.31.255.254 to access the LPS8N via Web or Console.

1288

1289

Please note the latest firmware uses port 8000 for http and 2222 for ssh access.

1290

1291

1292

== 11.4 I connect to the LPS8N's SSID but LPS8N didn't assign DHCP IP to my laptop? ==

(((

This is a known bug for the firmware version before 2019-09-23 for LPS, the issue was fixed since version: LG02_LG08~-~-build-v5.2.1569218466-20190923-1402.

)))

(((

In the old version, user can use the [[fall back ip method >>||anchor="H10.3A0IconfiguredLPS8NforWiFiaccessandlostitsIP.Whattodonow3F"]]to access and configure the device.

)))

= 12. Order Info =

**//PART: (% style="color:blue" %)LPS8N-XXX-YYY//: (%%)**

1308

1309

(% style="color:blue" %) **//XXX~://**(%%)**// Frequency Band//**

1310

1311

* (% style="color:red" %)** 868**(% style="color:black" %) : valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.

1312

* (% style="color:red" %)** 915**(% style="color:black" %): valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920

1313

1314

(% style="color:blue" %) **//YYY~://**(%%)**// 4G Cellular Option//**

1315

1316

* (% style="color:red" %)** EC25-E**(% style="color:black" %): EMEA, Korea, Thailand, India.

1317

* (% style="color:red" %)** EC25-A**(% style="color:black" %): North America/ Rogers/AT&T/T-Mobile.

1318

* (% style="color:red" %)** EC25-AU**(% style="color:black" %): Latin America, New Zeland, Taiwan

1319

* (% style="color:red" %)** EC25-J**(% style="color:black" %): Japan, DOCOMO/SoftBank/ KDDI

1320

1321

More info about valid bands, please see [[EC25-E product page>>url:https://www.quectel.com/product/ec25.htm]].

= 13. Packing Info =

(((

**Package Includes**:

1329

)))

1330

1331

* LPS8N LoRaWAN Gateway x 1

1332

* Stick Antenna for LoRa RF part. Frequency is one of 470 or 868 or 915Mhz depends the model ordered

1333

* Packaging with environmental protection paper box

1334

1335

(((

1336

**Dimension and weight**:

1337

)))

1338

1339

* Device Size: 12 x 12 x 3 cm

1340

* Weight: 187g

1341

* Package Size: 14.5 x 13.5 x 6 cm

* Weight: 300g

= 14. Support =

* Try to see if your questions already answered in the [[wiki>>doc:Main.WebHome]].

1349

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8.

1350

Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before mentioned schedule.

1351

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to:[[support@dragino.com>>url:file:///C:/Users/11315/Documents/D:/Projects/LoRa%20Product%20Line/LG308%20Picocell%20Gateway/LG308/LG308%20%25E8%25AF%25B4%25E6%2598%258E%25E4%25B9%25A6/support@dragino.com]]

Wiki source code of LPS8N - LoRaWAN Gateway User Manual

Applications

Navigation