Version 64.1 by Mengting Qiu on 2024/01/15 11:00
Show last authors
1 (% class="wikigeneratedid" %)
2 **Table of Contents:**
3
4 {{toc/}}
5
6
7
8
9 = 1. LoRaST v4 base Hardware =
10
11
12 Below hardware use LoRaST v4 module. They supports UART Access for AT Command and Firmware Upgrade.
13
14
15 {{velocity}}
16 $xwiki.ssfx.use("js/xwiki/table/table.css")
17 $xwiki.jsfx.use("js/xwiki/table/tablefilterNsort.js", true)
18 {{/velocity}}
19
20 (% border="1" cellspacing="5" class="doOddEven filterable grid sortable" id="tableid" style="background-color:#f2f2f2; width:869px" %)
21 (% class="sortHeader" %)|=(% style="width: 269px; background-color: rgb(217, 226, 243);" %)[[Models(% class="wikiinternallink sortarrow wikiinternallink wikiinternallink wikiinternallink wikiinternallink wikiinternallink wikiinternallink wikiinternallink" %)~[~[image:/xwiki/resources/js/xwiki/table/img/arrow-none.gif?cache-version=1648720710000~|~|alt="⇵" border="0"~]~]>>path:#||onclick="ts_resortTable(this);return false;" class="sortHeader"]]|=(% style="width: 158px; background-color: rgb(217, 226, 243);" %)[[Mother Board(% class="wikiinternallink sortarrow wikiinternallink wikiinternallink wikiinternallink wikiinternallink wikiinternallink wikiinternallink wikiinternallink" %)~[~[image:/xwiki/resources/js/xwiki/table/img/arrow-none.gif?cache-version=1648720710000~|~|alt="⇵" border="0"~]~]>>path:#||onclick="ts_resortTable(this);return false;" class="sortHeader"]]|=(% style="width: 214px; background-color: rgb(217, 226, 243);" %)[[UART for AT Commands(% class="wikiinternallink sortarrow wikiinternallink wikiinternallink wikiinternallink wikiinternallink wikiinternallink wikiinternallink wikiinternallink" %)~[~[image:/xwiki/resources/js/xwiki/table/img/arrow-none.gif?cache-version=1648720710000~|~|alt="⇵" border="0"~]~]>>path:#||onclick="ts_resortTable(this);return false;" class="sortHeader"]]|=(% style="width: 226px; background-color: rgb(217, 226, 243);" %)[[UART for Upgrade Firmware(% class="wikiinternallink sortarrow wikiinternallink wikiinternallink wikiinternallink wikiinternallink wikiinternallink wikiinternallink wikiinternallink" %)~[~[image:/xwiki/resources/js/xwiki/table/img/arrow-none.gif?cache-version=1648720710000~|~|alt="⇵" border="0"~]~]>>path:#||onclick="ts_resortTable(this);return false;" class="sortHeader"]]
22 (% class="even" %)|(% style="width:269px" %)PS-LB, PS-LB-NA, SDI12-LB|(% style="width:158px" %)SIB|(% style="width:214px" %)[[Instruction>>||anchor="H2.2UARTConnectionforSIBmotherboard"]]|(% style="width:226px" %)[[Instruction>>||anchor="H3.UARTforFirmwareUpgrade"]]
23 (% class="odd" %)|(% style="width:269px" %)(((
24 SN50v3, S31-LB, S31B-LB,
25
26 D20-LB.D20S-LB, D21-LB, D22-LB
27 )))|(% style="width:158px" %)SN50v3|(% style="width:214px" %)[[Instruction>>||anchor="H2.3UARTConnectionforSN50v3basemotherboard"]]|(% style="width:226px" %)[[Instruction>>||anchor="H3.UARTforFirmwareUpgrade"]]
28 (% class="even" %)|(% style="width:269px" %)LHT65N|(% style="width:158px" %)LHT65N|(% style="width:214px" %) |(% style="width:226px" %)
29 (% class="odd" %)|(% style="width:269px" %)(((
30 RS485-LB, SE01-LB, SPH01-LB,
31
32 LMS01-LB, LDS12-LB, LDS40-LB,
33
34 DDS75-LB, DDS45-LB, DDS04-LB,
35
36 DDS20-LB, MDS120-LB, MDS200-LB, WSC2-LB
37 )))|(% style="width:158px" %)RS485-BL|(% style="width:214px" %)[[Instruction>>||anchor="H2.4UARTConnectionforRS485-BLbasemotherboard"]]|(% style="width:226px" %)[[Instruction>>||anchor="H3.UARTforFirmwareUpgrade"]]
38
39 = 2. UART for AT Commands =
40
41 == 2.1 General software set up for AT Commands via UART ==
42
43
44 ~1. Use a general serial tool.
45
46 2. Connect PC to device's UART interface
47
48 3. Set up serial tool with : BaudRate: 9600, databit:8, No parity, No flow control.
49
50 (((
51 4. The password is the last six characters of APPSKEY or PIN of box
52
53
54 **Example：**
55
56 APPSKEY= 41 85 71 A7 5D 7E 54 52 25 58 74 85 96 14 74 85
57
58 The password：147485
59
60 [[image:image-20230329162900-1.png||height="302" width="648"]]
61
62
63 )))
64
65 [[image:image-20221224170218-1.png||height="497" width="640"]]
66
67
68 == 2.2 UART Connection for SIB mother board ==
69
70
71 [[image:image-20221224171304-3.png||height="545" width="863"]]
72
73
74 == 2.3 UART Connection for SN50v3 base mother board ==
75
76
77 [[image:image-20230515102801-1.png||height="635" width="860"]]
78
79
80 == 2.4 UART Connection for RS485-BL base mother board ==
81
82
83 [[image:微信图片_20230809144604.jpg||height="673" width="791"]]
84
85
86 == 2.5 UART Connection for DS20L mother board ==
87
88
89 **UART Connection for DS20L mother board:**
90
91 [[image:image-20231212145142-1.jpeg||height="676" width="796"]]
92
93 **Interface definition:**
94
95 [[image:image-20231212144745-2.png||height="279" width="510"]]
96
97 **DS20L programming line:**
98
99 [[image:image-20231212150405-2.jpeg||height="297" width="669"]]
100
101
102 == 2.6 UART Connection for AQS01-L mother board ==
103
104 [[image:image-20240115110027-1.jpeg||height="749" width="953"]]
105
106
107
108
109
110 = 3. UART for Firmware Upgrade =
111
112 == 3.1 Check Your device already have bootloader ==
113
114 === 3.1.1 What is Dragino Bootloader? ===
115
116
117 Dragino Bootloader is a customizer made bootloader which support below features:
118
119 * OTA Update via LoRa
120 * OTA Batch update configure via LoRa
121
122 All Dragino End Devices base on LoRa ST v4 supports Dragino Bootloader.
123
124
125 === 3.1.2 How can i know if my device already have bootloader? ===
126
127
128 If a device has a bootloader. it will output bootloader info to UART when boot. As below:
129
130 [[image:image-20230514150410-1.png||height="398" width="815"]]
131
132
133 === 3.1.3 How to upload bootloader to device? ===
134
135
136 If your is LoRa ST v4 base hardware and doesn't have bootloader. You can upload a bootloader to it.
137
138 **[[Downlink Link for OTA bootloader>>https://www.dropbox.com/sh/g4cp2lm85ovr8hu/AADX-4aEE-7SuKQAKTWrgKHIa?dl=0]].**
139
140
141 (% style="color:blue" %)**Update a firmware via TremoProgrammer:**
142
143 LoRaSTv4 Base hardware support UART update firmware. the UART connection is the same as AT Command connection, with the need for two extra action. See below for the steps:
144
145 (% style="color:blue" %)**Step1**(%%): Set BOOT Switch to (% style="color:blue" %)**PROG**(%%) mode. PROG mode is for update firmware specially.
146
147 (% style="color:blue" %)**Step2**(%%): Press (% style="color:blue" %)**Reset**(%%) button, the module will then boot into program mode.
148
149 (% style="color:blue" %)**Step3**(%%): Use (% style="color:blue" %)**TremoProgrammer**(%%) to update the firmware to LoRaST v4.
150
151 (% style="color:blue" %)**Step4**(%%): Set BOOT Switch to (% style="color:blue" %)**FLASH**(%%) position. Press Reset button again and module will run the new software.
152
153
154 Below is the method for how to update via (% style="color:blue" %)**TremoProgrammer:**
155
156 1.  **TremoProgrammer** download link:  [[https:~~/~~/www.dropbox.com/sh/j0qyc7a9ejit7jk/AACtx2tK4gEv6YFXMIVUM4dLa?dl=0>>url:https://www.dropbox.com/sh/j0qyc7a9ejit7jk/AACtx2tK4gEv6YFXMIVUM4dLa?dl=0]]
157
158 2.  Run** (% style="color:blue" %)TremoProgrammer.(%%)**
159
160 3.  Choose software and set the address to (% style="color:blue" %)**0x08000000**(%%).
161
162 4. Rember to set BOOT Switch to (% style="color:blue" %)**FLASH**(%%) after update finish. And you should be about to see Bootloader info in output after update
163
164 [[image:image-20230515171651-1.png]]
165
166
167 == 3.2 Update Firmware (Assume the device already have a bootloader) ==
168
169
170 Video Instruction: **[[https:~~/~~/youtu.be/G_xEZnNjJmM >>https://youtu.be/G_xEZnNjJmM]]**
171
172
173 === 3.2.1 Update a firmware via Dragino Sensor Manager Utility.exe ===
174
175
176 ~1. Download **[[OTA Tool>>https://www.dropbox.com/sh/bqepfzvusv6ig8e/AACKB4J9pdY1I7s5kcKfCUGHa?dl=0]]**
177
178 2. Use below schedule to update:
179
180 [[image:image-20230526105151-1.png]]
181
182 [[image:image-20230526105910-2.png]]
183
184 [[image:image-20230520100541-5.png||height="535" width="799"]]
185
186
187 = 4. FAQ =
188
189 == 4.1 How to recover if upgrade wrong file to bootloader? ==
190
191
192 You can just upload the bootloader again.
193
194
195 == 4.2 How to recover if upgrade wrong firmware via Dragino Sensor Manager Utility.exe? ==
196
197
198 The UART upgrade via Dragino Sensor Manager Utility.exe is base on Dragino Bootloader. So if you are able to upgrade some file via this tool. It means the device has bootloder.
199
200
201 The upgrade via Dragino Sensor Manager Utility is base on firmware level and won't effect the bootloader. If you upgrade a wrong firmware file, you can try below:
202
203 ~1. UART upgrade via Dragino Sensor Manager Utility again to the correct version. The password should use the AT PIN for the wrong firmware.  (This method is not 100% work, depends which wrong firmware you have upgraded)
204
205 2. Use **TremoProgrammer **to update firmware. [[Insturction>>||anchor="H4.3HowtouseTremoProgrammertoupdatefirmwareifthereisbootloaderinthedevice3F"]]
206
207 3. Use **[[OTA update>>http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]**, this is base on Bootloader so it will work. Make you choose the correct frequency band (base on the firmware version in the sensor or use EU868 which is the default setting.)
208
209
210 == 4.3 How to use TremoProgrammer to update firmware if there is bootloader in the device? ==
211
212
213 Make sure your device already bootloader while use this update. Otherwise device won't be able to boot ( can be solve by upload a bootloader to the device).
214
215 LoRaSTv4 Base hardware support UART update firmware. the UART connection is the same as AT Command connection, with the need for two extra action. See below for the steps:
216
217 (% style="color:blue" %)**Step1**(%%): Set BOOT Switch to (% style="color:blue" %)**PROG**(%%) mode. PROG mode is for update firmware specially.
218
219 (% style="color:blue" %) **Step2**(%%): Press (% style="color:blue" %)**Reset**(%%) button, the module will then boot into program mode.
220
221 (% style="color:blue" %)**Step3**(%%): Use (% style="color:blue" %)**TremoProgrammer**(%%) to update the firmware to LoRaST v4.
222
223 (% style="color:blue" %)**Step4**(%%): Set BOOT Switch to (% style="color:blue" %)**FLASH**(%%) position. Press Reset button again and module will run the new software.
224
225
226 Below is the method for how to update via (% style="color:blue" %)**TremoProgrammer:**
227
228 1.  Software download link:  [[https:~~/~~/www.dropbox.com/sh/j0qyc7a9ejit7jk/AACtx2tK4gEv6YFXMIVUM4dLa?dl=0>>url:https://www.dropbox.com/sh/j0qyc7a9ejit7jk/AACtx2tK4gEv6YFXMIVUM4dLa?dl=0]]
229
230 2.  Run(% style="color:blue" %)** TremoProgrammer.**
231
232 3.  Choose software and set the address to (% style="color:blue" %)**0x0800D000**. (% style="color:red" %)**VERY IMPORTANT for this address**.
233
234 4. Rember to set BOOT Switch to (% style="color:blue" %)**FLASH**(%%) after update
235
236 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/WebHome/image-20221224174341-4.png?width=374&height=471&rev=1.1||alt="image-20221224174341-4.png" height="471" width="374"]]
237
238

Applications

Navigation

Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0