Summary

• Page properties (1 modified, 0 added, 0 removed)
• Attachments (0 modified, 3 added, 0 removed)
  • image-20221224174341-4.png
  • image-20221224174529-5.png
  • image-20221224174605-6.png

Details

Page properties

Content

...	...	@@ -1,3 +1,13 @@
	1	+
	2	+
	3	+**Table of Contents:**
	4	+
	5	+{{toc/}}
	6	+
	7	+
	8	+
	9	+
	10	+
1	1	= LoRaST v4 base Hardware =
2	2
3	3	Below hardware use LoRaST v4 module. They module support UART Access for AT Command and Firmware Upgrade.
...	...	@@ -8,6 +8,56 @@
8	8	**PS-LB **
9	9	)))|(% style="width:135px" %)SIB|(% style="width:199px" %)Instruction|(% style="width:230px" %)Instruction
10	10
	21	+= UART for AT Commands =
11	11
	23	+== Generate software set up for AT Commands via UART ==
12	12
	25	+1. Use a general serial tool.
	26	+1. Connect PC to device's UART interface
	27	+1. Set up serial tool with : BaudRate: 9600, databit:8, No parity, No flow control.
13	13
	29	+[[image:image-20221224170218-1.png||height="497" width="640"]]
	30	+
	31	+
	32	+== UART Connection for SIB mother board ==
	33	+
	34	+[[image:image-20221224171304-3.png||height="545" width="863"]]
	35	+
	36	+
	37	+
	38	+= UART for Firmware Upgrade =
	39	+
	40	+== General Instruction for UART update firmware ==
	41	+
	42	+LoRaSTv4 Base hardware support UART update firmware. the UART connection is the same as AT Command connection, with the need for two extra action. See below for the steps:
	43	+
	44	+ **Step1**: Set BOOT Switch to **PROG** mode. PROG mode is for update firmware specially.
	45	+
	46	+ **Step2**: Press **Reset** button, the module will then boot into program mode.
	47	+
	48	+ **Step3**: Use **TremoProgrammer** to update the firmware to LoRaST v4.
	49	+
	50	+ **Step4**: Set BOOT Switch to **FLASH** position. Press Reset button again and module will run the new software.
	51	+
	52	+
	53	+Below is the method for how to update via **TremoProgrammer:**
	54	+
	55	+1.  Software download link:  [[https:~~/~~/www.dropbox.com/sh/j0qyc7a9ejit7jk/AACtx2tK4gEv6YFXMIVUM4dLa?dl=0>>url:https://www.dropbox.com/sh/j0qyc7a9ejit7jk/AACtx2tK4gEv6YFXMIVUM4dLa?dl=0]]
	56	+
	57	+2.  Run** TremoProgrammer.**
	58	+
	59	+3.  Choose software and set the address to **0x0800D000**
	60	+
	61	+4. Rember to set BOOT Switch to FLASH after update
	62	+
	63	+[[image:image-20221224174341-4.png||height="471" width="374"]]
	64	+
	65	+
	66	+== UART Connection for SIB mother board for Program. ==
	67	+
	68	+Below shows the SIB board UART connection, reset button and BOOT Switch (Program Jumper) position. They can be used for firmware upgrade reference.
	69	+
	70	+[[image:image-20221224174605-6.png||height="569" width="880"]]
	71	+
	72	+
	73	+

image-20221224174341-4.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Edwin

Size

...	...	@@ -1,0 +1,1 @@
	1	+22.7 KB

Content

image-20221224174529-5.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Edwin

Size

...	...	@@ -1,0 +1,1 @@
	1	+1.6 MB

Content

image-20221224174605-6.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Edwin

Size

...	...	@@ -1,0 +1,1 @@
	1	+1.5 MB

Content